Search Documents

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970

By T. F. Torries

The primary merit criteria used by the mining industry is internal rate of return (IRR) rather than net present value (NPV) although NPV is favored by academicians. This paper discusses the problems with IRR and NPV and compares the multi-goal nature of decision makers and their need for information with the characteristics of NPV and IRR. Conclusions are that both NPV and IRR are needed for investment ranking, that NPV suffers the same multiple root problem as does IR.R, and the determination of incremental IRR to reach NPV consistent project ranking is misguided in practice.

Jan 1, 1997

By Abdallah Khair, Nathalie Risso, Arie Herrera, Victor Tenorio

This study introduces a machine learning strategy to optimize icy regolith extraction from the Shackleton-de Gerlache Ridge using autonomous mining equipment. The model incorporates key parameters—distance, road gradient, vehicle load, speed, recharge logistics, and regolith water content—into a cost framework for excavation, hauling, and dumping. Regression models estimate energy and time requirements; classification predicts terrain navigability; clustering groups craters for efficiency; and K-Nearest Neighbors (KNN) determines optimal routing and scheduling. The system adapts to a six-month daylight cycle to maximize productivity and minimize costs, enabling intelligent planning for sustained lunar resource extraction under extreme environmental and logistical constraints.

Feb 22, 2026

By G. Vijaya Kumar, B. Srinivasa Rao, G. V. Krishna Rao

The paper outlines the ventilation practices prevailing in coal mines of Singareni Collieries Company (South India). The high annual average surface temperature and relatively steep geothermic gradient results in virgin strata temperatures in the region of 38- 42°C creating environmental problems in the working places. Expensive methods of air cooling can not be employed as the mines are small, and production and productivity do not justify the costs of artificial cooling of mine air. Controlled recirculation of mine air -- the unconventional technique being tried with success in some coal mines in U.K. has been analysed for improving the environmental conditions. The analysis shows that the method is safe, cost effective and can be applied with very little extra equipment.

Jan 1, 1991

By Robert S. Saunders

Cast iron tubbing for two centuries was the only practical watertight shaft lining for deep waterbearing formations. However, since World War II composite welded steel and concrete lining has gained favor and today is often preferred. While tubbing may not be applicable in all cases, a good argument can still be made for this time-honored method. Watertight linings are complex structures designed to withstand both hydrostatic fluid pressure, non-uniform loading created by ground forces, and vertical bending caused by subsidence. Resulting stresses in the lining can be high. To date linings have been designed that withstand hydrostatic pressures as high as 1,500 psi. Watertight linings must be robust, constructed of the highest quality materials, and manufactured and installed with precision. Therefore, such linings are expensive. Today's ductile cast iron tubbing is greatly superior to gray iron formerly used for tubbing, and is stronger, and more resistant to corrosion than welded steel lining. Tubbing, unlike steel linings, can be installed in wet conditions and used to control water inflow and stabilize unconsolidated ground as the shaft is deepened. Steel lining requires absolutely dry conditions for welding, which often necessitates expensive ground freezing and a primary lining.

Jan 1, 1985

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977

By Michael D. Sopko

This paper describes the project implementation from financing, through the engineering and construction phases, mine and process plant commissioning as well as operating experience realized to-date. The single line flowsheet used to process the lateritic nickel ore to a 75 percent nickel matte is presented with emphasis on the main pyrometallurgical operations. These include a rotary dryer, a unique reduction kiln, a 45 000 kVA electric furnace and two Pierce-Smith type converters. Associated infrastructure facilities and services necessary to sustain the 11 300 tonnes (12 500 short tons) per year nickel production rate are also described.

Jan 1, 1979

By F. G. Miller

To improve coal flotation Bethlehem Steel Corporation's Research Department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies5 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the bas is for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14M x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level.

Jan 1, 1968

By Michael Robert Hodson

I. Introduction The free market cash price of aluminium in the third quarter of 1985 is approximately $1000/tonne, well below the short as well as the long run marginal costs of production. The current disparity between marginal costs and price, as well as the pattern of prices since their high level in 1980, has led many economists to question whether prices are governed by the 'fundamentals'. Prices, some would argue, are the result of speculation; and speculation is irrational, little influenced by the fundamentals of the industry. The object of this paper is first to examine the relation between the fundamentals and price. A number of simple models are formulated and some empirical evidence is given to show that prices are not very different from costs. There are good reasons why costs and prices have fallen since 1980. Second, the connection is drawn between the fundamentals and speculation. To do this the concept of 'rational expectations' is defined and applied to a model of the aluminium industry. Then speculation is introduced into the model and the characteristics of the solution are examined. The object is to discover the new factors that determine prices and the basic change in the nature of the solution that is caused by speculation. 2. Prices and the Simple Supply-Demand Model Consider a simple model of the aluminium industry. Demand, D, is determined by economic activity, A, given exogenously, and inversely by the price, P. Supply, Q, is determined by the inverse of the rnarginal cost curve, and so varies inversely with exogenous factor costs, C, and directly with price. Price is determined by the equality of supply and demand. Given the equilibrium level of demand, price in this model is equal to the rnarginal cost of producing the required level of demand, P = MC (Dl. Algebraically, [ ] How well does this simple model explain the change in prices during the last five years? Table I shows the LME cash price and the estimated marginal cost of producing consumption during the second quarters of 1980 through 1985. The figures in the table show that price and the marginal cost of supplying demand both fell between 1980 and 1982, rose in 1983 and by 1985 had fallen again. Only in 1984 is the direction of change different. And during the 1980 to 1985 period, marginal costs fell by approximately $560/tonne while the LME cash price fell by $678/tonne. There is a correspondence between the fundamentals of cost and price over most of the individual years and the period as a whole.

Jan 1, 1986

By E. J. Haas, K. A. Rost

"This study sought to identify changes in continuous mining machine (CMM) operators’ risk perception and risk behaviors as a result of adding a proximity detection system (PDS) into their environment. To accomplish this research task, 9 CMM operators from 5 locations were interviewed. Interviews were thematically analyzed for constructs including patterns in risk perception and behavior before and after PDS integration and the process of adapting to the PDS. Operators discussed standing in the red zone less than they did before using the PDS; however, they also discussed other risky decisions they made while learning how to operate their CMM with the PDS technology such as “cheating” the technology and working faster to meet production goals. The process of relearning job tasks with technology and unintended behaviors as a result of that relearning process need to be taken into account when introducing new technology into the mine environment. The study results show an in-depth view of mine workers’ perspectives and how their job tasks and environment could be or are affected when learning how to use new technology that are relevant to companies and mine operators when introducing new technology into the mine environment. INTRODUCTION Established “red zones” can help prevent striking and pinning incidents by providing guidance to continuous mining machine (CMM) operators about where they should stand and not stand while operating a CMM. Although red zones influence operator placement positions, these guidelines are not foolproof safety mechanisms. Depending on the job task and circumstances of the mine environment, a CMM operator may unintentionally or intentionally stand in a red zone. For example, CMM operators may work in close proximity to their CMM for better visual attention cues and the ability to work at a higher rate of production [1-3]. To further enhance protection and prevent collisions between vehicles and mine workers, a proximity detection system (PDS) was developed for the industry. The PDS determines an individual’s position relative to a specific piece of machinery, issues visual and/or audible warnings to the mine worker to change positions, and, if necessary, disables machine motion [4]. The introduction of new technology within other sectors has been identified as a factor that influences work decisions. Specifically, previous research demonstrates that when technology debuts there can be an initial intrinsic risk perceived among users about how the technology will interact with their current environment and behaviors; however, these ambiguities, including the possible risks and benefits, are seldom studied [5]. Some research suggests that the constant presence of technology can disrupt situation awareness and decision-making capabilities by increasing worker responsibilities and worker cognitive demands [6-8]. Further, if workers’ perceived risks both with and without technology are misjudged, unsafe decisions that result in human error and injury may be more likely [9-11]. Although these statements are provided within a broad contextual framework, they support the need to study how technology is perceived among end users in their own environment. Because research about technological impact on worker behaviors has suggested both positive and negative consequences of technology, this issue is worth addressing in the mining industry. Specifically, research has not determined whether CMM operators view their placement choices in the red zone as safe or risky and what effect PDS technology has, if any, on risk perception and subsequent risk behavior."

Jan 1, 2015

By Peter B. Lilly

I appreciate the opportunity to tell you something about Kerr-McGee's Galatia Mine in Southern Illinois. This new underground mine was a departure for us since our previous experience had been gained in large surface mines in Wyoming. Although we were new, we did have the corporate experience in the operation of deep uranium and potash mines in New Mexico and Wyoming, and an earlier underground coal mine in Southeast Oklahoma. In arriving at our final design, we evaluated numerous concepts and finally settled on a two seam mine sharing a single shaft and slope. The mine, in turn, would be supported by a heavy media processing plant designed to optimize the yield from either seam. Further, we wished to be able to keep the two seams separate so that we could sell either seam separately or in a blend. Due to the thickness of the coal, the practical area dedicated to the mine provided forty to fifty years operations at the selected mine capacities. It was important, therefore, that our design and selection of hardware and systems provide for long life and low maintenance in order to compete in today's competitive markets.

Jan 1, 1984

By Robert Snow, Francisco Sotillo

Six types of amines were evaluated in the cleaning step of the rougher concentrate for the Crago “Double Float” process in terms of relative selectivity. Selectivity of these amines was ranked based on both batch and locked cycle flotation tests. Two parameters were used for selectivity ranking, the Selectivity Index, SI, and the ratio of insol rejection to the tailings weight percentage, R*. The comparison of the flotation results of the batch tests of the cleaning step of the Crago process for an unsized amine feed generated the following ranking from the most selective to the least selective mine: Quaternary > Primary [ ]Tertiary [ ] Condensate > Ether > Secondary(?).

Jan 1, 2002

By E. Scott Bair

Renewed interest in the vast reserves of anthracite coal in eastern Pennsylvania led to the use of a numerical model for simulating the hydrologic effects of constructing an open-pit anthracite mine. The proposed mine would be approximately 1800-m (5900-ft) long, 1000-m (3300-ft) wide, and 300-m (1000-ft) deep. A two-dimensional, finite-difference, ground-water flow model was used to calculate ground-water seepage rates into the proposed mine, to evaluate the effectiveness of various deep-well dewatering systems, to calculate drawdown in adjacent wells and properties, and to estimate the capacity of the water-treatment plant. Site-specific values of pertinent hydrogeologic parameters were used in the simulations.

Jan 1, 1980

Since 1992 the Grasberg Mine, located in the remote regions of Indonesia, has utilized the Modular Mining System. Over the last several years, major steps have been taken to maximize this productivity enhancement system. These steps include; the Automated Lineup, the Linear Program upgrade, tracking of Mean Time Between Failure, a MEDS system interface, a VMIS system interface, and implementation of the new Graphical Operator Interface Console with Global Positioning, This application of new technology and innovation has lead to improved performance, understanding and reporting, as well as the quality of the Indonesian Engineers. These efforts have contributed 10 Grasberg achieving one of the lowest mining costs in the copper industry.

Jan 1, 1998

By Eric Gilmore, Ron Tudor, Gregory E. Korbin, Bill McCormick, Brad Bush

INTRODUCTION Las Vegas has recently been termed the “Construction Capital of the Country”. It has also been acknowledged as the fastest growing city in the country for several years running. The rapid growth improves the economic picture of the region but it also imparts unusual demands on the area’s infrastructure. In 1994 the Southern Nevada Water Authority (SNWA)was working on a master plan to address the rapid growth. A long range analysis revealed the need for additional water treatment capacity and delivery systems. Short term projections showed that the current system would reach capacity in the summer of 1997 with the possibility of demand exceeding the supply. The River Mountains Tunnel #2 is part of a $150M scheme to quickly upgrade the system to meet the short term demand, improve the overall system operation and allow for a smooth transition into the larger additions being planned for the future. The SNWA selected Carollo/Black & Veatch (CBV) to provide detailed design and construction management for the upgrades. The River Mountains Contracts consisted of five separate contracts broken out separately to stream line a very aggressive (just 34 months) design and construction schedule. Necessary work included four miles of excavated and lined tunnel, connections from existing pipelines to and from the new tunnel including large diameter (to 3.66m(144 in)) valves, a 18 927cu m (5 million gal) regulating reservoir, a surge tank and a 170 343cu m (45 million gal) reservoir to add additional storage to the system. Notice to Proceed was given to Kajima Engineering and Construction (Kajima) on May22, 1995 for the construction of the River Mountains Tunnel #2. The design called for a tunnel to be driven 6070m (19 915ft) in rock and lined to a finished diameter of 3.71m (12.17ft).Excavation began on December 14, 1995 and holed through on April 30, 1996. Lining began on June 25, 1996 and a notice of Substantial Completion was issued on December 13,1996. This paper describes the measures taken to complete the tunnel in 18 months from Notice to Proceed to Substantial Completion. THE RIVER MOUNTAINS SITE The River Mountains are a low range of rugged mountains separating the Las Vegas Valley from its main supply of water, the Colorado River at Lake Mead. They are volcanic in origin and the harsh desert environment has left them as expanses of exposed bedrock rising 305m (1000ft) above the valley with little or no vegetation. An existing 3.05m (10ft)

Jan 1, 1997

By C. Anastasiadis

The wettability of sandstone was investigated using the technique of dielectric spectroscopy in the frequency interval 1kHz-1MHz. The natural wetness of the material was modified to get two different sets of samples, one with sea-water wetness and the other with crude oil wetness. Measurements showed that the electric responses of water-wet and crude oil-wet samples were markedly different beside the fact that the dielectric response of both groups of samples obeys a general fractional power law. The dispersivity, of the complex permittivity component that expresses the material loss with respect to the electric field was found to be the most suitable parameter to check the wettability of the samples.

Jan 1, 2005

By Edoardo Misano, Magali Schivre, Martino Semeraro, Alain Bochon

"INTRODUCTIONThe Laboratoire Souterrain de Modane (LSM) is an underground research laboratory located in the Western Alps on the French – Italian border. It is located in the middle of the 13km long Fréjus highway tunnel that links Modane (France) to Bardonecchia (Italy) in correspondence of the highest overburden of 1800m. The LSM current activity is mainly based on the investigations about the dark matter and requires very sensitive instrumentation which shall be protected from cosmic rays. To comply with the new legislation about safety in tunnels, the highway tunnels owners agreed in 2007 the construction of a parallel safety tunnel, at an average distance of 50m from the existing tunnel and the laboratory owner CNRS (Centre National de recherche scientifique) also decided to extend the existing laboratory with the construction of a new 17000 m3 cavern allowing the installation of wider and more powerful instruments that could increase chances of success of research. Preliminary studies stated that, considering both geological and functional issues, the most appropriate location for the new laboratory shall be in between the two tunnels and parallel to the existing laboratory (see Figure 1).Hence, the CNRS asked Systra, already in charge of the works supervision of the safety tunnel, to realize the design of the new cavern. The laboratory extension includes the construction of a 40 m long cavern with 300 m² cross section and two smaller tunnels connecting the safety tunnel and the existing laboratory to the new cavern. The minimum distance between the front face of the new LSM and the highway tunnel is about 25 m.The French and the Italian authorities, responsible of the exploitation of the Fréjus highway tunnel, asked the CNRS to develop an accurate study indicating that the construction of the laboratory extension would not have any negative impact on the existing structures of the highway tunnel. The main results of the developed study by Systra are summarized hereafter. The construction works should begin prior to the end of the construction works of the Fréjus safety tunnel in 2018."

Jan 1, 2016

By C. Ptacek, D. Hiller, J. L. Janbor, H. Mccreadie

Between 1991 and 1994, metallurgical residues from a pressure-oxidation autoclave at the Campbell Au-quartz mine at Red Lake, northern Ontario, were neutralized with dolomite-rich flotation tailings and were deposited in a polyethylene-lined disposal area. Mineralogical analysis indicates that most of the As occurs as a crystalline ferric sulfarsenate, and some is associated with Fe oxides and with K-H3O jarosite. Field pore-water geochemical data from 1994 and 1995 showed increases in Fe(II) and As(III) concentrations, suggesting that the sulfarsenate and jarosite are dissolving; none of the discrete As phases included in a thermodynamic database limit dissolved-As concentrations, and these concentrations may continue to increase. These results demonstrate the potential for Fe and As loading through groundwater systems.

Jan 1, 1998

By V. Roze, R. N. Parkinson, R. Shepherd

The alphaDOSIMETER is a complete, integrated system designed to monitor the immediate worksite of underground miners where the disintegration for radon daughters is a risk to the health of mining personnel. The dosimeter weighing little more than one pound is worn by each miner throughout the entire shift and is powered by the miner's cap lamp battery. After this integration period, the unit is connected to a reading network whereupon the day's data is dumped, calculated and stored. Beginning in July 1980, prototype units were subjected to vigorous underground testing in uranium mines in Canada and the United States and in tin mines in Cornwall, U.K. The testing results are summarized and proposals advanced for a typical mine monitoring system utilizing the alphaDOSIMETER.

Jan 1, 1981

By Michael Deutscher, Jozef F. Zurawski

Part of Capital Improvement Project SE-754 tendered by New York City Department of Design and Construction included installation of a 96-in. (2.47 m)diameter sewer by pipe jacking methods. The pipe selected by the Contractor, EIC Associates, Newark, New Jersey, was a glass-fiber-reinforced thermosetting resin pipe installed in two reaches: 72 m (235-ft.) and 222 m (728-ft.). The machine selected for the excavation was an open face shield. This paper describes the set up of the tunneling operations, subsurface conditions, progress of excavation, pipe performance and other details of the project including unexpected difficult ground conditions that were encountered during excavation and how these conditions were overcome.

Jan 1, 2003