Search Documents

By A. M. Galperin

Back analysis is a very important procedure for proper understanding of physical processes. Back analysis can be used to establish the role of different factors, define parameters to be calculated and formulate the behavior of natural or physical processes based on field experimental results. It is evident that, in order to obtain the necessary data for back analysis, field observations are required. For the Michailovsky region (Kursk Magnetic Anomaly, KMA) the long-term strength characteristics of the clay covering the quarry slopes were established with the help of back landslide calculations. The obtained data allowed quantification of the shearing resistance parameters at the presence or absence of intermittent dips of discharge in the pit bank massif structures. Based on the results of investigation for material composition, strength and deformation of finely dispersed (clay-chalk) deposits in the Kursk Magnetic Anomaly including measuring of the settlements of filled structures, complex probing and laboratory determination of water-physical and mechanical properties of "man-made" soils, engineering-geological zoning of filled structures was carried out.

Jan 1, 2005

By D. T. Iseley, David Bennett, Christopher Norris

The microtunneling test program is one of three main elements of the research project, "Trenchless Construction: Evaluation of Methods and Materials to Install and Rehabilitate Underground Utilities." The other elements of this project include an evaluation and demonstration of horizontal directional drilling technology and pipeline rehabilitation systems. The research is a Corps and Industry cost-shared project funded under the Construction Productivity Advancement Research (CPAR) program. The laboratory partner is the U.S. Army Engineer Waterways Experiment Station (WES), Geotechnical Laboratory. The industry partner is the Louisiana Tech University's Trenchless Technology Center. Industry participants are contributing over half the total cost of this research. The overall objective of the CPAR program is to improve productivity in the U.S. construction industry, thereby enhancing the competitiveness of the U.S. industry in domestic and overseas markets. The Corps and other federal and state agencies will benefit by realizing reduced costs, enhanced safety and better products and services as the products of this research program are developed, tested, and pushed into the market place. The microtunneling demonstrations and evaluations were performed during September and October 1992 at a specially constructed test facility built at WES in Vicksburg, MS. The test facility is 104 m (340-ft) long, 5 m (16-ft) wide, and 4 m (13-ft) deep. It was constructed, ironically, by first excavating a trench into which 6 different types of soils were placed and compacted in approximately 18.3 m (60-ft) long sections. The soil profiles include a lean silty clay (loess), a dry sand, highly plastic buckshot clay, wet sand, clay gravel and silt. The interfaces between soil profiles were sloped to simulate mixed face conditions as the machines exit one zone and enter another, and provided challenges to ground control and alignment and grade control during these transitions. Moisture and density tests were performed on all materials in each lift to assure uniformity. Horizontal inclinometers and 3 levels of settlement plates were installed at key locations in the test bed. The settlement plates and rods and the horizontal inclinometers, together with surface survey points, provided data to evaluate settlement and heave along the test section. Penetration resistance was measured in each section of the completed test bed. Strain gages were installed in 8 of the 0.6 m (24 in.) diam. Hobas pipe sections to measure strains in the pipe as it was being jacked into place. Steering jack loads, jacking thrust loads, and cutterhead torque were also measured during the drives. The results of these tests will be used together with other information to develop guidelines for conducting feasibility studies and selecting proper methods compatible with anticipated conditions.

Jan 1, 1993

By V. F. Swanson

M&MP, Volume 6, No. 4, November 1989, pp. 190-196

Jan 1, 1990

By Robert H. Shannon

Coal is the primary fuel for U.S. electric per generation -- over 78% of U.S coal production. In 1987 over 56% of electric per generation was from coal-fired plants. Areas of concern confronting the expanded use of coal for per generation include environmental, political and the nation's energy security and economy. These matters and available alternatives and options directed to the expanded use of coal are reviewed.

Jan 1, 1989

By Donald O. Rausch, William E. Hawkes, Odin Jr. Strandberg

INTRODUCTION Kennecott Copper Corp.'s Tintic Div. Burgin mine is a 725 t/d (800 stpd) lead-zinc producer, located in the east Tintic mining district, 5.6 km (3.5 miles) east of Eureka, and 130 km (80 miles) south of Salt Lake City, UT. The Burgin mining complex includes three shafts, shop, dry, and office facilities, and a 454 t/d (500 stpd) flotation concentrator. Production and ser¬vice entry to the mine is through a 4.26-m (14-ft) diam concrete-lined production shaft, and a three-compart¬ment rectangular shaft. A connection with the Apex No. 2 shaft and the Burgin mine provides a second exhaust airway. Bear Creek Mining Co., Kennecott's exploration sub¬sidiary, began exploration of the Burgin mine area in 1957 with the sinking of the 335 m (1100 ft) deep No. 1 shaft. A station was cut at the 320-m (1050-ft) level of the shaft and extensive drifting, diamond drilling, and some winzing and raising confirmed the presence of a major lead-zinc ore body, the main portion of which oc¬curred below a hot saline water table. Surface facilities and the 4.26-m (14-ft) diam concrete-lined production shaft were completed in 1966. Ore production has been steadily increased to 725 t/ d (800 stpd) since 1966. The collar elevation of the No. 2 production shaft is 1731 m (5678 ft) above sea level. The mine's three levels, the 1050, 1200, and 1300 are at elevations of 1414.6, 1356.4, and 1338.1 m (4587, 4450, and 4390 ft), respectively. The approximate elevation of the hot saline water table is 1382.6 m (4536 ft). The earliest production on the east Tintic mining district was from the Eureka Lilly mine in 1909. Later, in 1916, the Tintic Standard mine was discovered, and pro¬duced ores with a gross value of $80,000,000 through 1956. The Eureka Standard mine located 1.6 km (1 mile) southwest of the Burgin mine produced ore worth $12,000,000 from fissures in the Tintic quartzite along the Eureka Standard fault. Ores produced from the east Tintic mining district through 1971 are valued at $151.3 million. The production from the entire Tintic district is approximately $500 million. GEOLOGY The Burgin ore deposit occurs as replacement bodies in limestone, dolomite, and shale. Numerous fault struc¬tures and rock formations make the mine geology com¬plex. The mineralization is strongly associated with sev¬eral major geological features, which include the Ophir formation, consisting of limestone, dolomite, and shale as the favorable host rock, and the structural influence of the east Tintic thrust, the Eureka Standard and sev¬eral other significant faults. Fig. 1 depicts the Burgin 1300 level workings, a generalized configuration of the ore body, and the main geological features. Covering the quartzite, limestone, dolomite, and shale facies enclosing the Burgin ore deposit are 183 to 274 m (600 to 900 ft) of andesite. The Burgin ore consists of massive sulfide and oxide lead-zinc ores with significant silver and cadmium val¬ues. The main ore minerals are galena, cerrusite, and spalerite. Extensive manganese oxide deposits are associated with the lead-zinc ore occurrence. A limited

Jan 1, 1982

By Michael G. Nelson

Underground coal mining practice often requires that some coal be left in place at the seam boundaries after mining, for purposes of ground control, quality control, machine guidance, or good operating practice. Many methods for measuring the thickness of boundary coal have been developed, but only the natural % R gamma background method as bee used in routine operations. Use of this method is constrained by the level and consistency of the natural gamma background in the bordering strata, the accuracy of the gamma detection instrument, and the elevation profile of the seam boundary being detected. Computer simulations for three commercially available gamma detection instruments, designed for mine use, showed that measurement of boundary coal thickness by the natural gamma method can provide satisfactory input for horizon control systems when the gamma detector is large, when the sensor is mounted on the mining machine, and when the elevation profile of the seam boundary does not change rapidly in the direction of advance.

Jan 1, 1993

By E. A. Schmidt

In 1962, while investigating the tungsten potential in the Thompson Creek area for Union Carbide Corp., Henry T. Eyrich obtained anomalous concentrations of molybdenum (up to 19 ppm Mo) from stream sediment samples collected along Pat Hughes Creek, a tributary to Thompson Creek. Follow-up investigations by Eyrich during the same year disclosed the presence of a hydrothermally altered and molybdenite-bearing granitic exposure in the headwaters of Pat Hughes Creek about 2.4 km (1.5 miles) upstream from the sample point. The altered outcrop measured about 549 by 305 m (1800 by 1000 ft), contained abundant northwest-trending quartz veins locally with molybdenite, and was overlain and surrounded by the Challis volcanic extrusive sequence of mid-Tertiary age. Eyrich's subsequent soil and rock chip geochemical sampling program over the altered outcrop area showed a general increase in the molybdenum content to the northwest toward the postmineral Challis volcanic cover. Over a distance of about 305 m (1000 ft), values in the altered intrusive rock increased from less than 5 ppm Mo to over 600 ppm Mo, with aconcomitant intensity of the hydrothermal alteration pattern. Based on these geochemical results and on preliminar; megascopic hydrothermal alteration studies, Eyrich correctly concluded that the altered outcrop is an erosional window and that molybdenum mineralization of sufficient grade could exist beneath the Challis volcanic cover some distance further to the northwest. His recommendation to test the area of potential molybdenum mineralization with several drill holes was, however, declined by Union Carbide in 1962. The property remained unclaimed until 1967, when Eyrich joined Cyprus Mines Corp. Acting on Eyrich's recommendation, Cyprus immediately staked 26 lode mining claims to cover not only the altered intrusive outcrop, but also the northwest trend of mineralization where it projected beneath Challis volcanic rocks. Eleven of these claims are now patented.

Jan 1, 1991

By L. Adler

Determining whether a railroad locomotive will skid under varying conditions is a fairly routine, pervasive problem. However, some of the equations provided are wrong, others are at best murky. All require correction or clarification. Skidding during heavy braking is a crucial safety problem, possibly resulting in loss of control and collision. It can also be an economic detriment, ruining wheels and tracks and, by inhibiting acceleration, causing reduced full-speed times. While skidding is less likely for rubber-tired equipment, a comparable problem exists for tractor-trailers operating on poor surfaces. The primary reference is to the SME Mining Engineering Handbook (pp. 14-11, Eqs. 7 and 8), which is taken as authoritative and normative (Brantner, 1973). Fundamentally, the physical weight of the locomotive can never be negative (-). However, based on this reference it can be negative on adverse grades, during braking (Eq. 7), and on favorable grades, whether accelerating or braking (Eq. 8). Additionally, it should be noted that the term rW should be Rw. To avoid having the locomotive weight turn out negative, "absolute value" brackets must enclose the right-hand expression of both equations. Also, the weight of locomotive can be greater than the right-hand side value introducing the common "greater than or equal to" symbol (>_). While these alterations are easy to make, the use of the algebraic sign associated with each term is still confusing, as

Jan 1, 1991

By Charles A. Maliszewski, James M. Galvin, Gerhard Urschitz

With obvious signs of deterioration, the double track, historically registered Bergen Tunnels as part of the commuter rail system in New Jersey waited for rehabilitation for a long time. Serious water in filtration not only caused operational and safety hazards for the electrified rail line but also deteriorated and structurally compromised the tunnel lining. An innovative rehabilitation program was developed to enlarge the tunnel and to provide a new waterproofing system and final lining. For the rock excavation and support New Austrian Tunneling Method (NATM) principles were utilized, while water tightness was achieved by installing a PVC membrane waterproofing system followed by a reinforced cast-in-place final lining. Experienced on-site supervision generated additional savings during construction by streamlining support elements based on geologic conditions encountered.

Jan 1, 2003

By Jamal Rostami, Jürgen Schmitt, Rohola Hasanpour

"Double Shield TBMs can be used in fast track projects for accelerated completion where there is limited information available on ground conditions and there are possibilities of encountering weak ground and shear zones. As such, the shielded TBMs are the primary choice of the machines in long tunnels, but face the possibility of entrapment in squeezing ground, which entails long delays and major risks. This paper examines the possibility of using ground improvement methods to increase ground strength, and thus, increase the capability of the machines to cope with squeezing ground conditions. In this study, 3D finite difference simulation of a shielded TBM in squeezing ground was performed to estimate the operational parameters including required thrust to get a machine out of an entrapment. This analysis was also used to evaluate the possibility of preventing machine jamming by the implementation of pre-excavation ground improvement to increase the strength of the ground. INTRODUCTION In order to face adverse tunneling conditions especially using a shielded TBM in squeezing ground, new shield designs, with extra thrust and torque, step shield geometry with reduced shield diameter from front to the back, and conical shape shields have been used. In addition, many of the new machines have the capability to implement ground improvement at distances up to 50 m ahead of the face in order to reinforce the ground and further increase in their chances to cope with squeezing ground conditions. While these features have been added to the machine, there has not been a thorough evaluation of their impact on improving the chances to avoid machine jamming in weak rocks at high depth, which is conducive to rapid convergence of the ground."

Jan 1, 2016

By T. P. Meloy

Improvement of grade and recovery requires the use of optimum processing circuits. Critical to an optimum circuit is the set point for separation. With the introduction of the concept of circuit analysis (Meloy, 1982), it became possible to determine optimum circuits for a given task. No analysis, however, has yet been made as to the grade requirements of the larger circuits. Williams and Meloy (1982), reviewed the literature and concluded that, within the operating range, most unit operations involved in particle separation behave linearly. For the purposes of this analysis, linearity will be assumed. Grade, G, is defined as the weight of the coal mineral, C, that appears in the product, divided by the weight of the coal mineral plus the weight of the gangue mineral or waste mineral, Q, which appear in the product.

Jan 1, 1982

By Edward Hall Smith

The E1 Indio Mine is located in the Andes mountains about 180 kilometers East of La Serena, capital of the Fourth Region of Chile. It is reached by an international highway running up the Elqui Valley as far as Juntas from where the last 42 kilometers is on a road constructed by the Company. The plant is located at 3.900 meters above sea level among extremely rugged terrain with nearby mountains rising about 5.500 meters. Climatic conditions at these altitudes are severe with winter temperatures down to -20°C. Snow storms lasting several days and leaving up to two meters of snow have been experienced, while fierce winds are corm=.

Jan 1, 1984

By Nathaniel Arbiter

The increasing size of flotation cells as the use of flotation has increased is traced from the first United States application of the process in Montana in 1911 through the following eight decades, using data from the Taggart handbooks (1927) and (1945), from the SME Handbook (1984), and from recent manufacturers' catalogues and other sources for the 1980s and 1990s. With the earliest mechanical cells less than 1 m3 (359) in volume and the largest now available at 200 m3 (7,000ft3), three requirements are necessary: 1) demonstration of advantages in replacing smaller volume by larger volume cells; 2) estimating power requirements, impeller dimensions, and operating rpm by correlation equations; 3) considering effects of using larger cells, in necessarily much shorter rows, on process kinetics. The resulting seven tables that address these problems are presented, and their implications discussed.

Jan 1, 1999

By John C. Nigro

Bench scale and pilot plant research was conducted using dolomites (CaO,MgO) lime as the basic additive in the preparation of self-fluxed pellets from a typical magnetic taconite concentrate (5.57 S_2). The specific objective of this investigation was to ascertain the viability of the magnesia lime pellets in high temperature oxidizing and reducing atmospheres. Pellet basicity and induration temperature were major parameters affecting fired pellet quality; temperatures ranging from 1,200° to 1,250" C appeared to be the most favorable for production of self-fluxed pellets with basesities (B) above 1.0. Comparison of the mechani¬cal and metallurgical properties of regular (acid) and self-fluxed pellets (B 1.55) produced under similar conditions in a modified grate pelletizing machine showed that the self-fluxed pellets were more resistant to abrasion and to high and low temperature reduction disintegration, an important consideration in commercial application. The Plus 3 mesh Linder index increased from 68 percent (regular pellets) to over 90 percent (self-fluxed pellets). The reducibility and swelling indices of the self-fluxed pellets were found to be comparable to the regular pellets.

Jan 1, 1972

By Graham Jones

During 1982 Ash Grove Cement Company contracted with Wagester, Walker, Thornton & Company to convert a Calcimatic rotating hearth kiln at its Portland, Oregon lime plant from gas/oil to coal firing. Increasing costs of natural gas and No. 6 fuel oil made this conversion mandatory if the plant was to remain competitive. Unique features of this project are 1) the distributors of pulverized coal to eighteen small burners around the inner and outer perimeters of the doughnut-shaped kiln, and 2) the attrition-dryer-pulverizer mill. Ash Grove, a century-old lime and cement producer headquartered in Overland Park, Kansas (Kansas City area), looked at various schemes for multiple burner firing before employing Wagester, Walker, Thornton & Company. W.W.T. of Pitts- burgh, Pennsylvania was formed in 1980 by acquiring the Solid Fuels Division of the Pullman Swindell Corporation. This division had been active in developing solid fuel firing for brick tunnel kilns, principally in the Southeast. They continue to supply such systems firing wood waste as well as coal to the brick industry and have also converted two Calcimatic lime kilns for Dixie Lime, Sumterville, Florida, a fluid bed calciner for Texas Gulf in Aurora, North Carolina, and a chrome concentrate kiln for Diamond Chemicals at Castle Hayne, North Carolina. Testing and a proposal have been made for INMETCO, Elwood City, Pennsylvania, on an annular hearth furnace for direct reduction of iron ore to metallic iron.

Jan 1, 1984

By Robert B. Fulton, Gill Montgomery

Fluorspar is the commercial name for fluorite, a mineral that is calcium fluoride, CaF2. The name, derived from the Latin word fluere (to flow), refers to its low melting point and its early use in metallurgy as a flux. It is the principal industrial source of the element fluorine. Two other minerals, cryolite and fluorapatite, have significant fluorine content. Cryolite, sodium aluminum fluoride, Na3AlF,, is a rare mineral that has been found in commercial quantities only in Greenland. The natural material has been supplanted by synthetic cryolite for its principal industrial use in the manufacture of aluminum. Fluorapatite, Ca5F(PO3)2, is a source of phosphate for fertilizer manufacture, containing a small percentage of fluorine. Commercially mined deposits of apatite have varying amounts of fluorine, chlorine, hydroxyl, and carbonate. HISTORY Fluorspar was used by the early Greeks and Romans for ornamental purposes as vases, drinking cups, and table tops. Various peoples, including the Chinese and the American Indians, carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola in 16th century Europe. Fluorspar mining began in England about 1775 and at various places in the United States between 1820 and 1840. Production grew substantially following the development of basic open hearth steelmaking, wherein it is used as a flux. Use was stimulated by growth of the steel, aluminum, chemical, and ceramic industries, particularly during World Wars I and 11. Fluorocarbons entered the picture in 1931. The use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel began in 1942. Differential flotation for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s and the application of heavy media concentrating methods to the treatment of low grade ores in the 1940s were outstanding technological advances that facilitated increased production. Pelletizing and briquetting of flotation concentrates for use in steel furnaces and the development of flotation schemes for beneficiating ores containing abundant dolomite and barite have been major improvements in the industry. USES OF FLUORITE Fluorspar is used to make hydrogen fluoride (HF), also called hydrofluoric acid, an intermediate for fluorocarbons, aluminum fluoride, and synthetic cryolite. It is used as a flux in the steel and ceramic industries, in iron foundry and ferroalloy practice, and has many minor specialized uses. Hydrogen fluoride is produced by reacting acid grade (97% CaF,) fluorspar with sulfuric acid in a heated kiln or retort to produce HF gas and calcium sulfate. After purification by scrubbing, condensing, and distillation; the HF is marketed as anhydrous HF, a colorless fuming liquid, or it may be absorbed in water to form the aqueous acid, usually 70% HF. Synthetic cryolite, organic and inorganic fluoride chemicals, and elemental fluorine are made from hydrofluoric acid. The acid itself is important in catalysis in the manufacture of alkylate, an ingredient in high-octane fuel for aircraft and automobiles; in steel pickling, enamel stripping, and glass etching and polishing; and in various electroplating operations. The manufacture of one ton of virgin aluminum requires about 12 to 29 kg of fluorine content in synthetic cryolite and aluminum fluoride. This quantity, through improved technology and recovery practices, is being lowered significantly in countries with the most advanced technology (i.e., Australia and Sweden), while others (i.e., Surinam and South Africa), remain at the high end. Elemental fluorine is prepared from anhydrous hydrofluoric acid by electrolysis. Gaseous at room temperature and pressure, fluorine is compressed to a liquid for shipment in cylinders or in tank trucks. Elemental fluorine is used to make uranium hexafluoride, sulfur hexafluoride, and halogen fluorides. Gaseous uranium hexafluoride is used in separating U235 from U233 by the diffusion process. Sulfur hexafluoride is a stable high dielectric gas used in coaxial cables, transformers, and radar wave guides. Halogen fluorides have important applications, mostly as substitutes for elemental fluorine, which is more difficult to handle. Emulsified perfluorochemicals, organic compounds in which all hydrogen atoms have been replaced by fluorine, are undergoing investigation as promising blood substitutes. They transport oxygen and, in conjunction with a simulated blood serum, perform many functions of whole blood. With further development, these organic compounds may ultimately, in emergencies, be useful in saving lives of animals and humans during periods of acute shortages of natural blood. Inorganic fluorides are used as insecticides, preservatives, antiseptics, ceramic additives, and fluxes and in electroplating solutions, antioxidants, and many other products. Boron trifluoride is an important catalyst. Organic fluorides are volume leaders in the fluorine chemical industry. Fluorinated chlorocarbons and fluorocarbons are prepared by the interaction of anhydrous HF with chloroform, perchlorethylene and carbon tetrachloride, and are characterized by low toxicity and notable chemical stability. They perform outstandingly as refrigerants, aerosol propellants, solvents, and cleaning agents and as intermediates for polymers such as fluorocarbon resins and elastomers. Fluorocarbon resins are inert compounds that have unusually low coefficients of friction and have found a number of applications as lubricants for parts that cannot be oiled, e.g., bearings for window raising equipment located inside of automobile doors, in small electronic equipment, for the manufacture of chem-

Jan 1, 1994

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

By W. Blake, J. K. Whyatt, B. G. White

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations in in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence collected from the Lucky Friday mine by US Bureau of Mines researchers, as well as a review of previous case studies, demonstrated that in situ stress variations affect the [spatial] distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies. they are too expensive and, depending, on conditions, may be too difficult to collect. However, information on borehole and raise breakouts: deformation of mine openings: and patterns of seismicity, ground-control problems and rock-burst damage can be used to build a stress database. In conjunction with maps of mine structure and geology and models of rockmass behavior, this database can then be used to build a map of in situ stress variations. Such a map could provide a means of anticipating patterns of mining-induced seismicity and. Thus, could be the basis for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1997

By H. Para, A. Aguirre, G. Artadi

Mining is a very important economical activity in Peru which has been recently developed without considering environmental aspects. Here, we show an experience at the Milpo mine, situated 4,200 meters above sea level; a mining company that has the value of being one of few from the last decade that is engaged in consolidating a model of environmental protection. The model includes aspects of contamination prevention and control, with bioindicators such as pasture cultivation, vegetables, forests, and hydrobiological species breeding. Socially, through means of development programs in natural areas, forestation and support to rural agriculture, together with environmental education, it is being demonstrated that it is possible to ensure tangible results in environmental conservation and the well-being of the populations around the mine.

Jan 1, 1998

By K. N. Santini

Natural zeolites are gaining recognition as an important commodity with an increasing number of industrial and consumer applications. This potential has prompted the Anaconda Minerals Company and other firms to investigate occurrences and markets for zeolites. The deposits of mordenite-rich tuff at Rome are of interest for their economic potential and for the excellent opportunity they provide to study a zeolite deposit formed in a hydrologically closed basin. Location The Rome property is located approximately 9 km west of Rome, Oregon, in Townships 31S. and 32S., Range 41E., Malheur County. It lies within the Owyhee Uplands of the northern Basin and Range physiographic province (Figure 1). The area discussed here includes a major portion of the depositional basin in which the zeolitic tuffs occur.

Jan 1, 1982