Search Documents

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By Christian Heinz, Doug Harding

TBMs can last for decades and be rebuilt project after project with proper maintenance. How successful can rebuilt TBMs be? At the DigIndy Tunnel System in Indianapolis, Indiana, USA, a rebuilt TBM was used to great effect. The 6.2 m diameter Main Beam, originally manufactured in 1980, bored 40+ km of tunnels and set three world records in its size class of 6 to 7 m, including a best month of 1,754 m. In this paper, the authors analyze the TBM rebuild, performance and lessons learned to make recommendations for future projects seeking to use rebuilt TBMs over long distances.

Jun 23, 2024

By Ulrich Maidl, Gustavo Aguiar, Argemiro Ferreira, Marco A. Peixoto Silva, Marc Comulada

"Metro Line 5 in Sao Paulo is being constructed. This lot extends for 4,940 m with twin EPB shield tunnels under a dense and busy urban area, with an excavation diameter of 6.9 m. The tunnels run predominantly in the tertiary soils of Sao Paulo where extensive experience exists from previous EPB shield tunnel projects. However, new experience is being gained in Sao Paulo in shield tunnelling through Saprolite, the weathered product of the underlying Gneiss crystalline basement, through the resulting residual soils and in rock-soil mixed face conditions. Furthermore, experiences in difficult mixed face soil conditions with overconsolidated clay at the face in combination with loose sands at the crown under the groundwater table will be presented. Additionally, the design, operational and controlling approach followed for the shield drive at particular critical cross-sections where the shields were driven close or under buildings. INTRODUCTION Within the framework of Sao Paulo´s metro network expansion, the excavation of the shield tunnels for Metro Sao Paulo Line 5 is currently taking place. The present paper deals with the description of the most relevant features from the construction of the Line 5 – Lot 3 tunnels. The paper presents how particular challenges were dealt maximising potential of EPB shield tunnelling technology. Challenges were posed not only by the difficult boundary conditions of urban shield tunnelling, such as shield drive under buildings, but also by complex geotechnical situations. PROJECT DESCRIPTION The great urban area of São Paulo is one of the biggest cities in the world, with around 20 Million people living in the city and in the suburb area. The city faces great mobility problems and in the last years the government has been investing great amounts on the megacity´s metro expansion. The Line 5 Extension plays an important role to connect the south area to the central area of the city, with a whole extension of 11 kilometres, including 11 new stations. It is estimated that this line will transport almost 900.000 passengers/day. The first stretch of the expansion, Lot 3, consists of two single tunnels, almost 5 kilometres long each, crossing 4 stations. Figure 1 shows details of the Line 5 Expansion."

Jan 1, 2016

By D. H. Carlson, J. H. Johnson, C. F. Renders

Introduction Diesel-powered vehicles are used extensively in underground mines throughout North America. The bulk of the diesel vehicles found in underground mining operations are used for loading and ore haulage, as well as for transportation of personnel and supplies. Along with the advantages of using diesels underground is the disadvantage associated with diesel-tailpipe particulate-matter emissions (DPM). The concentration of DPM in the ambient air of US underground metal mines is not now regulated by the Federal Mine Safety and Health Administration (MSHA). However, recent studies have shown DPM to be mutagenic (National Institute of Occupational Safety and Health, 1988), and the American Conference of Governmental Industrial Hygienists (ACGIH) has recommended that the exposures of per¬sonnel to DPM be limited to an 8-hr time-weighted average concentration (threshold limit value or TLV) of 0.15 mg/m3 (Anon., 1995). The authors, while making measurements in a number of US underground mines that use diesel haulage equipment, found mine air DPM concentrations ranging from 0.2 to 2.36 Mg/M3 (McCawley and Cocalis, 1986; Watts et al., 1989; Cantrell et al., 1991; Haney, 1992; US Bureau of Mines, 1992; Watts, 1992; Watts et al., 1995). If the proposed DPM TLV were to be adopted as a permissible exposure limit (PEL) for US underground mines, the proposed limit of 0.15 mg/m3 PEL would be lower than any of the concentrations measured in the earlier studies and would represent more than a 15-fold reduction from the maximum 2.36 mg/m3 concentration. A 0.15 mg/m3 PEL would also represent a 4.5-fold reduction from the average 0.68 mg/m3 measured mine ambient air DPM concentration reported in this paper. Other diesel tailpipe emissions that are now regulated underground include carbon monoxide (CO), with a PEL of 50 ppm; nitrogen dioxide (NO,), with a PEL of 5 ppm; nitric oxide (NO), with a PEL of 25 ppm; and sulfur dioxide (SO,) with a PEL of 5 ppm. Because the concentrations of these gaseous pollutants and DPM are affected by the state-of-maintenance (Waytulonis,1992), it is important that a means be developed to measure emissions from engines that are now in service to determine when maintenance is needed. The current study was the result of an inquiry by mine¬maintenance personnel who had been receiving complaints about high concentrations of diesel soot (DPM) in mine headings from load-haul-dump (LHD) vehicle operators. Mine-maintenance personnel were searching for an objective test to determine if the diesel tailpipe particulate emitted was excessive. The mine was also evaluating electronically controlled, two-cycle, naturally aspirated, direct-injection diesel engines on some of their JCI (John-Clark Inc.) load-haul-dump (LHD) vehicles. These LHD vehicles were used to haul freshly blasted ore from mine headings to a feeder breaker. The feeder breaker breaks down the larger chunks and feeds the broken ore onto a conveyor. Michigan Technological University, in past studies, developed an emissions-measurement apparatus (EMA) ca¬pable of measuring diesel vehicle tailpipe pollutant concentrations (Chan et al., 1992; Chan et al., 1993; Carlson et al., 1994). At the time of the study reported here, most of the mine's LHD vehicles used a 12-cylinder, four-cycle, naturally aspirated prechamber diesel engine. The study was undertaken in cooperation with mine maintenance supervisors from late 1992 through July 1993. The objectives were to compare diesel exhaust emissions between the 6-cylinder, two-cycle, electronically controlled, direct-injected diesel engine and the 12-cylinder, four-cycle, prechamber diesel engine and to, then, use the data collected, in conjunction with mine ambient air measurements, to demonstrate the application of the "deterioration factor" (Chan et al., 1992), which is a measure of the state-of-maintenance of mine-vehicle engines that are now in service. The information would be used to identify vehicles that need maintenance to reduce emissions. The data reported here are unique in the sense that they combine underground diesel vehicle ambient and tailpipe

Jan 1, 1999

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

The oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bi, Pb, Sb, As, and Cu contents in the speiss by two-step simulation differed from the industrial data by 0.6 wt.%, 0.8 wt.%, 2.6 wt.%, 7.2 wt.%, and 8.6 wt.%, respectively. Twostep simulation results indicated that the speiss partitioning of Sb, As, and Cu increased from 60.1%, 32.3%, and 27.5%to 81.6%, 67.8%, and 47.2%, respectively, with the smelting temperature increasing from 1050 °C to 1250 °C. While the metal partitioning of Sb and Cu increased from 0% and 2.7% to 15.2% and 13.3%, respectively, with the separation temperature increasing from 400 °C to 700 °C.

Oct 19, 2020

By Sihua Lei, Hong Zhong, Shuai Wang, Yu Gan, Zhanfang Cao

High purity MgO is widely used in various fields as an important magnesiumcompound. The separation of Mg and Ca is of great importance for the preparation of high purity MgO from dolomite. In this study, the key effects of carbonization temperature and nano-calcium carbonate agglomeration on the separation mechanism of calcium and magnesium have been investigated. The results indicated that the reaction in the carbonization process was stepwise. Precise control of the carbonization temperature was essential for the formation of Mg(HCO3)2 due to its low reaction efficiency at lower temperatures or decomposition markedly at higher temperatures. Meanwhile, there was a common-ion effect in solutions containing Mg2+ and Ca2+. Nano-CaCO3 particles were formed during carbonization and agglomerated with the prolongation of static time. A product with a purity of 99.56% MgO and 0.16% CaO was obtained under the optimized conditions: ratio of liquid–solid 30 L/g, carbonization temperature 22–25 °C, carbonization time 1 h, and refining time 4 h. This work has important guiding significance for the preparation of high purity magnesium oxide from dolomite.

Apr 21, 2020

By M. H. Rauschkolb, J. A. Cremeens

Geotechnical solutions were developed for closure of two historic, remote underground mines in the deserts of southern California. Closure criteria included access closure, minimal site impact, and optimum use of native materials. The closure designs and construction activities incorporated techniques for protecting sensitive biota, particularly bats and desert tortoise. The types of mine openings that were closed include adits, declines, shafts, daylighted stopes, and dugout dwellings. The desert locations permitted implementation of cost-effective closure techniques that relied upon the use of native materials. The strategies and techniques developed for these desert closures are adaptable to other climates.

Jan 1, 2002

By Amila Sandaruwan Ratnayake, T. Dilmi. U. Wijewardhana, H. C. S. Subasinghe

The value addition potential of ilmenite was examined using several characterization techniques. Raw ilmenite is composed of 93.65 wt.% of FeOTiO2, 3.55 wt.% of SiO2, 1.22 wt.% of Al2O3, and the remainder being other minor oxides. Ilmenite and powdered carbonized coconut shells were mixed in the weight ratio of 4:1. A separate fraction of the same mixture was added with powdered seashells in the weight ratio of 4:1:0.5. Six fractions of each mixture were distinctly milled from 1 to 6 h in a planetary ball mill. XRD spectra (broadened and diminished reflections of ilmenite) and FTIR observations (Ti―O―Cbonding) of milled samples indicate the possible incorporation of carbon into the ilmenite structure. Any clues of an occurrence of new rutile peaks were not observed in XRD spectra of milled samples. Consequently, the carbothermic reduction has not been initiated during mechanical activation. In this case, samples powdered for 6 h in a mill were isothermally annealed for 2 h under normal airflow at temperatures of 800 °C, 1000 °C, and 1200 °C, respectively. According to the X-ray diffractograms, the annealing temperatures of 1000 °C and 1200 °C exhibited almost similar trends with rutile (R), pseudobrookite (PB) and elemental iron (F), and a very few ilmenite (I) peaks. Consequently, 6 h of milling and 1000 °C annealing were concluded as the optimum conditions for the carbothermic reduction. Moreover, this study indicated seashells as a potential rate raiser for the carbothermic reduction of ilmenite at 800 °C. Therefore, this process is applicable to upgrade ilmenite into a mixture of synthetic rutile and elemental iron.

Mar 29, 2021

By M. Ramachandran, R. G. Reddy

"A direct route for the reduction of magnesium oxide to magnesium using thermal plasma processing, with methane as the reducing gas, has been systematically evaluated. A feasibility study of the reduction reaction has been performed on the MgO-CH4 system at different methane concentrations and temperatures. The effects of changes in the key process parameters, such as the oxide-to-methane ratio and plasma power, on the yield of magnesium have been systematically evaluated. A maximum yield of about 61 mol% Mg was obtained using power of 20.0 kW and a molar ratio of MgO:CH4=1:1. Phase, morphological, elemental and binding energy analyses were performed on the product powders to understand the reduction reaction. Surface oxidation was observed in smaller magnesium particles in all the experiments, while the in-situ sintering of magnesium rods was observed at a molar ratio of MgO:CH4=1:1.5. Magnesium carbide (Mg2C3) was observed in the product, and its mechanism of formation is proposed using phase equilibrium data and a predominance diagram.IntroductionMagnesium has an excellent combination of low density and high strength. These properties have increased worldwide demand for and use of magnesium. Two major processes are used in the commercial synthesis of magnesium metal. The first method is electrolytic reduction and the second is thermal reduction using Pidgeon process. These processes can be classified as traditional techniques, but there are numerous emerging technologies that aim at reducing the production cost of Mg, its environmental impact and energy consumption. Thermal plasma processing is one emerging technique that has great potential in all the abovementioned key areas of magnesium production.Traditional reduction techniques. Two major reduction techniques, namely electrolytic and thermal reduction, have been used in the commercial production of magnesium. Electrolytic reduction is typically carried out in electrolytic cells from magnesium chloride (obtained from seawater or well and lake brines) (Tripp, 2009). The following simplified reaction shows the reduction of magnesium chloride to liquid magnesium and chlorine gas:"

Jan 1, 2015

By Ricardo D. Presnell, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Russell C. Babcock, William L. Gunter, Thomas R. Gibson, Douglas N. Halbe, Jay W. Hammitt

The Barneys Canyon orebody is a sediment-hosted disseminated gold deposit located 8 km (5 miles) north of the Bingham Canyon porphyry copper mine. Mineable oxide reserves are 8.6 million tonnes (9.5 million short tons) grading 1.64 g/tonne (0.048 oz/ton) gold. Host lithologies are carbonates and siliciclastics of the Park City and Kirkman-Diamond Creek Formations of Lower Permian age. Gold distributions are controlled by favorable stratigraphic units and associated alteration, and structures. Dominant alteration is decalcification and bleaching of carbonates, and argillization and bleaching of sandstones. Gold to silver ratios are greater than 1:1. Anomalous trace metals include arsenic, antimony, mercury and thallium. The Melco deposit lies 2.4 km (1.5 miles) southwest of the Barneys Canyon deposit. It is spatially associated with a steeply northwest-dipping siliciclastic breccia in the Kirkman-Diamond Creek Formation at the contact with underlying orthoquartzites of the Freeman Peak Formation. Both gold-bearing oxidized and sulfide lithologies are present, often in sharp contact. Mineable oxide reserves are 2.8 million tonnes (3.1 million short tons) grading 2.40 g/tonne (0.07 oz/ton) gold. Anomolous trace metals include arsenic, antimony, mercury and thallium, which are generally present in concentrations greater than those at Barneys Canyon, particularly in sulfide-bearing material. A spatial, temporal and genetic relationship is proposed between the Melco deposit and late-stage gold mineralization at Bingham Canyon, although both the Melco and Barneys Canyon deposits have many similarities to Carlin-type gold deposits.

Jan 1, 1990

By Kumar Vikram

Rich reserve of prime quality limestone in east khasi hills of India and abundant quantity of low-cost fuel (Natural Gas) in Bangladesh made Lafarge Surma cement limited a joint venture company of Lafarge France and Cementos Molins Spain to envisage an integrated cement plant at Chatak District-Sylhet) a bordering town of Bangladesh. Since April 2006 the single flight 17 km Long Belt Conveyor (LBC) built by M/S Larsen & Toubro Ltd. (L&T), ECC Division an engineering and construction company of India, is feeding limestone/shale to the Lafarge Surma cement plant. This engineering marvel was created on a turnkey basis with technology support of M/S Aumund France

Jan 1, 2008

By S. W. Swerson

25.1-THE PURCHASING FUNCTION The word "purchase" means "to obtain by paying money or its equivalent; to buy for a price." This definition is all too simple to properly describe the word "purchase." One should consider the basic objectives of purchasing-to procure the right material, of the right quality, in the right quantity, at the right time, from the right source at the right price. Here it should be noted that in purchasing it is recognized that the best quality or grade of materials may be the only grade to purchase for a specific job. However. there are other jobs where the medium, standard or poor grade of materials is the right quality, as the lesser grade will perform adequately. In some companies the purchasing department makes the decision as to the right quality, while in others this function is shared with other departments. Years ago in business the owners controlled the purchase of required materials and services by performing the task themselves. The owners obtained the type materials and services they needed and paid the price demanded. This function was performed along with all the other duties requisite to the owner of a business, namely, clerical, hiring and firing of personnel, financial management, etc. As companies grew in size, clerical duties were assigned to other personnel and the owner usually retained the purchasing authority. This same division exists today in many small companies. However, in the larger companies, the purchasing function has been assigned to a separate department. Importance of the Purchasing Function-The larger the company the greater the need for a separate department to perform the purchasing function. Today the purchasing agent for most larger progressive companies has policy-making authority. Therefore, it is reasonable for him to report to the president or vice president of his company. Studies of several hundred companies show the purchasing department head reporting to top management 87.5% of the time. This fact in itself is indicative of the importance of recognizing that effective purchasing requires a department staffed with specialists in the field of procurement with knowledge and experience sufficient to perform in today's complicated business atmosphere. In the manufacturing field it is a common axiom that usually half of the company's dollar expenditures are for materials. If a purchasing department functions properly and the right product or service is purchased and a savings accomplished, the contribution to the net profit of the company is much greater, as opposed to sale dollars, where only a small portion is carried forward to net profit. Thus, the importance of the purchasing department and the contribution it can make to the success of the company are obvious. 25.1.1-THE PURCHASING FUNCTION 1. Responsibilities of the Purchasing Function-The purchasing agent in performing his function is acting as an agent for the company and others in the company requiring materials and services. Accordingly, he is committing the company for materials and services subject to certain limitations which the board of directors may stipulate. In view of this, the purchasing agent,'^ position must of necessity he

Jan 1, 1973

By I. Pordea

The materials used for the construction of buildings contain natural radionuclides of the U238 and Th232 series and are ? 50% due to land radioactivity. Another component of natural radioactivity is K40, with ? 40%. The presence of these radiopollutants in the final products (i.e. bricks, concrete) due to body irradiation is by two pathways: external irradiation and internal irradiation. External irradiation is due to gamma radiations emitted by Pb214 (RaB) + Bi214 (RaC) from the U238 series, by Ra228 (Mezothoriu I) + Ac228 (Mezothoriu II) + Tl208 (ThC??) from the Th232 series and by the K40 radionuclide. Internal irradiation is due to inhalation of radon (Rn222) and Rn220 (Tn) plus short life descendents (Po, Pb, Bi), radionuclides which are present in concrete. A fraction from radon present in concrete enters into a house leading to internal irradiation by inhalation. In Romania, the maximum concentration of radon allowed for new buildings is 200 Bq/m3.

Jan 1, 2008

By E. Sirolli

In recent times, with rare exceptions, most economically viable ore discoveries have been large, low-grade and located in remote parts of the world. Mining companies have often shown to be incapable of mitigating their social and economic impact on local communities. Sustainable development and relations can be achieved by implementing bottom-up methodologies to the top-down tools already in use by mining companies. In order to magnify the importance of enterprise facilitation as a primary method for community development, data from 25 years of community based work around the world was used. Results highlight the need for a grassroots approach to local economic and community development, which focuses on the creation of a parallel economy in communities. Using solely top-down methodologies for developing community relations is shown to be a limited resource for mining companies. There are fundamentally two dangers for mining companies: alienating the local population, resulting in militancy and lengthy legal battles to obtain a license to operate; and, being accountable for building social and economic infrastructure that are not the company?s responsibility.

Jan 1, 2012

By Osvaldo A. Bascur, J. Pat Kennedy

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. The lack of an integrated approach makes the profitability of metallurgical plants lag behind that of other industries despite technical advances that have occurred in recent years. This results in significant deterioration in the ability to maintain a "smart” operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. Combining real-time infrastructure with portal technology is becoming an accepted methodology. This paper introduces real-time portals and team sites to support decision making by work- groups which require both real-time and documentary information from manufacturing assets, vendors, head office and the Internet. Workers get insight from the overall process effectiveness index based on key variables such as losses due to plant availability, performance efficiency and rate of quality. Real-time portals and smart clients are part of any real-time performance management (RtPM) solution. Three case studies in large metallurgical complexes are presented. PLANTS ARE YOUR STRATEGIC HANDICAP Information technology is arguably one of the fastest moving technologies used by the mining/metallurgical industry. However, the business model for managing that

Jan 1, 2004

By Derek J. McCracken, William G. Holroyd

Emery is a rock that at one time held a large share of the abrasives market. The introduction of synthetic abrasives, however has forced it to settle for only certain niches in the marketplace. This loss of market share is due mainly to the higher amounts of impurities and weaker internal structure that naturally occurring minerals have compared to manmade materials. The use of rocks and minerals as abrasives dates back to early man, who used flint, quartz, and other natural materials to fabricate various tools. During the 19th century, with the Industrial Revolution imminent, the character of the abrasives industry was changed forever as synthetics were introduced. Frank B. Norton is credited with producing the first manmade abrasive when, in 1855, he manufactured a vitrified grinding wheel using emery grit and clay. Before Norton's accomplishment emery had been the only commercially available abrasive. The latter part of the 20th century has seen synthetics capture an increasing share of the abrasives market from natural materials. The term emery is believed to have been derived from the words emeri (French), smeriglio (Italian), and smiris (Greek). The term corundum, for the principal mineral of emery, seems to have originated from kauruntaka, the Indian name for the mineral. GEOLOGY Emery is a gray to black, granular rock comprised of various minerals including corundum (A1,0,), an iron-bearing mineral (usually magnetite-Fe,O,, hematite-Fe,O,, or hercynite- FeAI,O,), and several trace impurities such as mullite, titania, silica, and magnesia. The hardness of emery normally ranges between 7 and 9 on the Mohs scale, depending on its mineral com- position and level of impurities. Corundum, the hardest mineral in emery, typically has a hardness of 9. The specific gravity of emery ranges from 3.2 to 4.5, also depending on mineral composition and purity. The crystallography of each mineral contained in emery differs somewhat. Corundum exhibits an hexagonal crystal structure, whereas magnetite forms within the isometric system, frequently as octahedral crystals. Hercynite, an iron spinel, is also isometric. Hematite has an hexagonal structure but often is found as botryoidal and reniform masses. Principal deposits of commerical emery are found in the United States, Turkey, and Greece. In the United States two emery producers in the Westchester County-Peekskill area and one in the Cortlandt County area of New York closed their mines in the late 1980s. Commercial production in the United States now comes only from the western Cascade Range in Oregon. The emery in New York has a typical A1,0, content of 41.5%. Most of the rock is not true emery because it contains a mixture of spinel and magnetite but very little corundum. The deposits are of Late Ordovician-Early Silurian age and consist of veins in which emery is mixed with olivine, pyroxene, and hornblende. The veins evidently were formed by contact metamorphism and are surrounded by Precambrian schists that contain mica, sillimanite, cordierite, garnet, and quartz. The deposits in Oregon were formed during Miocene time by the contact metamorphism of ferrunginous bauxite by intrusive lamprophyric dikes and plugs. Emery is found in thin layers bordering these tabular dikes, which are usually oriented perpendicular to bedding, and in "surficial placer deposits. The emery deposits in Turkey occur as small, massive, lens- shaped bodies and as surficial placers. They are believed to have formed during Permian and Triassic times. In Greece the principal site of emery production is at Cape Emeri on the Island of Naxos. These deposits consist of lenticular masses of emery surrounded by marble. They originated during Mesozoic time, evidently by metasomatic replacement. Smaller deposits on several other Aegean islands were formed by the metamorphism of bauxite or other alumina-rich materials.

Jan 1, 1994

By H. Kinilakodi, R. L. Grayson

In 2010, the U.S. Mine Safety and Health Administration (MSHA) began holding hearings on a new coal mine respirable dust rule, which proposed a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the “hot spots” where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines’ compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, average mining height and selected “hot spot” counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications for the need for better dust control methods.

Jan 1, 2012

By Stanley J. LeFond

The Republic of Botswana, one of the newer countries of southern Africa, attained independence on September 30, 1966. It covers an area of about 225,000 square miles (582,000 square kilometers) which makes it slightly larger than France, or slightly smaller than Texas. It is bounded by Zimbabwe, the Republic of South Africa and Namibia, including the Caprivi Strip. Angola and Zambia are close neighbors. (Map 1). Botswana lies at the center of the southern African plateau at a mean elevation of 3,300 feet (1,000 m). It is a natural habitat for most species of African fauna. The rolling sands and extensive grasslands of the Kalahari Desert cover the southwest. The climate is sub- tropical. Summers, although tempered by north- easterly breezes, are hot, but mean maximum temperature seldom rises above 100°F (38°C). Winters are dry with wide temperature variations, which often give rise to frosts.

Jan 1, 1981

By CASSANDRA L. HOEBBEL, Jennica L. Bellanca

High-fidelity, immersive training is known for its learning and logistical benefits. While other industries have used virtual reality (VR) for decades, the same uptake has not been seen in mining. NIOSH recently developed an adaptable, scalable VR training platform, VR Mine Rescue Training (VR-MRT), which has attracted significant industry interest. NIOSH is using VR-MRT to understand the barriers to adoption and implementation of VR. As a part of a larger effort to assess the effectiveness and implementation of VR-MRT, researchers have conducted pre-implementation interviews. In this paper, the authors use feedback from individuals at various implementation levels to assess the acceptability and appropriateness of VR-MRT and identify potential implementation barriers for VR more generally. Researchers also describe ongoing efforts to overcome these barriers as NIOSH works to position VR-MRT as a supplemental resource more generally for mine safety training.

Feb 1, 2025

By A. E. Desrosiers, R. L. Kathren, D. L. Haggard, J. M. Selby

INTRODUCTION The radiological health significance of thorium-230 stems from its tendency to separate from the uranium238 parent, concentrate in bone tissues, and to subsequently irradiate the radiosensitive tissues lining the bone surfaces and the bone marrow. Indeed, thorium-230 may be the radionuclide which contributes the major dose following intake of natural uranium (Hartley and Pasternack 1979). This is reflected by the most recent recommendations of the International Commission on Radiological Protection, which specify the limits shown in Table I for the annual intake of radionuclides by occupationally exposed workers (ICRP 1979). TABLE 1. Occupational Annual Intake Limits (microcuries per year) for Selected Uranium Nuclides and Daughters (ICRP 79) [Radionuclide Ingestion Inhalation] [Uranium-238 200 0.05 Uranium-235 200 0.05 Uranium-234 200 0.03 Thorium-234 300 200 Thorium-230 3 0.02 Radium-226 2 0.5] Clearly, the relatively low annual limit of intake for thorium-230 shows it to be of greater radiological concern than its parent radionuclides. Because of the greater toxicity and different metabolism of thorium-230, monitoring only for uranium-238 does not satisfactorily identify the possible hazard from thorium-230 nor does it provide any real indication of the metabolism or biodynamics of these two radionuclides. Thorium-230 has a half-life of 80,000 years and can be detected by direct counting of the alpha particles or photons emitted during its transformation to radium-226. The 4.69 and 4.62 MeV alpha particles are distinctive and specific indicators of thorium-230 and are emitted with abundances of 76% and 24%, respectively. The principal photon, a 68 keV gamma ray, is emitted in only 0.37% of the transformations and is, therefore, not useful for low level measurements. The other photons emitted have even lower yields, or, in the case of radium L x-rays, are non-specific and, hence, useless for quantification. High sensitivity measurements of thorium-230 currently are usually accomplished by wet washing of the sample substrate, quantitative chemical separation of thorium atoms, and, finally, direct measurement of the alpha particles emitted from a massless deposition. This procedure is complicated, expensive, and time-consuming, and subject to interferences from uranium, other actinides, and other thorium isotopes. Recently, the feasibility of low-level measurement of thorium-230 by neutron activation analysis (NAA) was demonstrated (Kathren, Desrosiers and Church 1980). Two principal variations of the NAA method were used in this study: 1) instrumental NAA technique and 2) post-irradiation radiochemical separations (RCS). Instrumental NAA procedure is a nondestrucive technique which is preferred because of its simplicity. The procedure is as follows: after irradiation with a known neutron fluence, the samples are transferred to a clean container and quantitative gamma spectroscopy performed. With the radiochemical separations procedure, the sample is initially treated as in the instrumental technique. However, after irradiation, a known amount of "carrier" is added to the sample. The element(s) of interest are then separated from the rest of the matrix by distillation, precipitation and extraction techniques. The resulting sample, now free of interferring elements, is then ready for gamma-ray analysis. The use of a "carrier" is to determine the loss of element-of-interest during the chemical separations process. The neutron activation cross section of thorium-230 has an epicadmium resonance value of 1,010 barns (Mughahghab and Garber 1976) and a thermal neutron cross section of 23 barns. The 25.52 hr thorium-231 produced releases two photons of significance: an 84 keV complex, (6.5% yield) and 25.6 keV (15% yield) (Lederer and Shirley 1978). The 84 keV complex is particularly useful for quantification since neither natural uranium, thorium, their daughters, or activation products emit photons in this region. However, the higher yield of the 25.6 keV photon may result in increased sensitivity if there are no other photons of similar energy emitted by other radionuclides in the sample. PRELIMINARY STUDIES Thorium-230 standard stock solution was prepared from a pure sample of the oxide purchased from Oak Ridge National Laboratory. From this stock solution a series of samples were prepared for irradiation in the TRIGA Mark I reactor at Reed College. Various dilutions were prepared as well as thorium-230 spiked urine samples. Irradiation times varied from 1 to 54 minutes in a neutron fluence rate of 1.84 x 1012 n/ cu m-sec. The neutron spectrum was abundant in thermal neutrons, having a Cd ratio of approximately 10. Treated urine samples were also analyzed by the NAA instrumental method. Analysis of untreated urine samples was not possible due to the high background

Jan 1, 1981