Search Documents

By Michael J. Pratko

The bulk handling industries have long been plagued with problems in their attempt to obtain one of their major goals - the maximum efficiency for which a bulk handling flow system was designed. Mentor Dynamics Ltd. is an international firm with offices in Canada, Japan, and the United States. Mentor Dynamics Ltd. is in the business of solving the "why not" of a system and engineers the solution for the problem. Studies of the varied difficulties encountered with bulk flow systems indicate that 90% of all flow problems fall into one or more of the following categories: abrasion, impact, sticking, and/or inadequate design. These problems can occur with a myriad of bulk solids: coal, gypsum, aragonite, phosphate, fly ash, ore. Solutions to the problems are as varied as the problems. The proper lining material, ceramic, urethane, rubber, and/ or ultra high molecular weight polyethylene, must be coupled with the correct fastening system, annular ring and 'F' cap, weld washer, button head fastener, weld studs and/or nuts and bolts.

Jan 1, 1982

By M. Zhang, H. Ni, F. Zheng, M. Guo

"In the present work, we investigate the effects of roasting temperature and time on the transformation of the titanium (Ti)-bearing phase and magnesium aluminate spinel (MgAl2O4) phase in Ti-bearing electric arc furnace molten slag during the molten sodium hydroxide (NaOH) treatment process. With applied temperature of 700 °C for 60 min, and a mass ratio of Ti-bearing electric arc furnace slag to NaOH, or Rslag/NaOH, of 1:1.2, the conversion ratios of the Ti-bearing phase and the MgAl2O4 phase reached about 98.3 percent and 88.1 percent, respectively. Moreover, investigation of the reaction kinetics indicate that the conversion of these phases during the molten NaOH treatment process is a typical solid-liquid reaction, and it can be theoretically described by the unreacted shrinking core model. The conversion ratio of the Ti-bearing phase was found to be controlled by the chemical reaction step, with an apparent activation energy of 41.76 kJ/mol. The decomposition of the MgAl2O4 phase was found to be controlled by the surface chemical reaction in the early stage of 0 to 20 min from start of reaction, changing to diffusion control in the later stage of 20 to 60 min. The apparent activation energies of the process were determined as 55.88 and 22.72 kJ/mol, respectively.IntroductionChina has rich mineral resources of vanadium–titanium magnetite ore deposits, and the iron and steel industry in the country produces millions of tons of titanium (Ti)-bearing slag every year. The problem of how to dispose of the Ti-bearing slag has attracted much attention, and various approaches have been developed, including the acid process (Li et al., 2007; Zhang et al., 2011; Zhang and Nicol, 2010; Li et al., 2011), alkali fusion process (Han et al., 2012; Middlemas, Fang and Fan, 2013; Nayl, Awwad and Aly, 2009; Lasheen, 2008; Zhang, Qi and Zhang, 2009), carbonization and chlorination process (Liu et al., 2008; Tao et al., 2012; Fu et al., 2012; Liu, 2009), selective crystallization process (Lei and Xue, 2008; Li et al., 2011; Zhang et al., 2007a, 2007b). However, these processes have been beset by various functional, economical and ecological problems (Yu and Chen, 2010). With environmental protection regulations becoming increasingly rigorous, and demand growing for the comprehensive utilization of resources, the focus is on methods to treat Ti-bearing slag with high efficiency and mild reaction conditions (Nazari and Riahi, 2011; Wu et al., 2013)."

Jan 1, 2017

By Sumit Kumar Hota, Asadi Srinivasa Reddy, Ashok Kumar, Ashish Agrawal, Surajit Sinha, Chandra Sekhar, Tanay Ray

In the current operational facility, due to the absence of pellet pot facility, a novel technique is developed wherein the pellets with different chemistries prepared in the laboratory are fired in an induration machine by placing them inside the Inconel baskets. In the present work, an attempt is made to optimize the pellet chemistry by developing 2 different flux pellets, viz., low basicity (B2: CaO/ SiO2 = 0.3) pellets and high basicity (B2 = 0.9) pellets, and further the effects of basicity on pellet properties, viz., cold compressive strength, porosity, swelling index, reducibility index, and softening and melting temperature, are studied. It has been found through the multiple operational trials that increasing the basicity of pellets from 0.3 to 0.9 results into improving the pellet strength, reducibility and softening and melting characteristics. Moreover, it is observed that the swelling index of pellets is reduced by adding 2% MgO to both low and high basicity pellets that could be attributed to the formation of high melting point slag in pellets. The operational trial has resulted into producing pellets that exhibit a combination of desired mechanical strength, improved swelling, and reducibility index and possess better softening–melting behavior among all the chemistries studied.

May 24, 2022

By Richard E. Ray

INTRODUCTION Main mine fan installations at underground coal mines must be designed to comply with the requirements outlined in 30 CFR (Code of Federal Regulations) Part 75. However, very little emphasis is typically placed on the aerodynamic optimization of shaft collar designs, ductwork configurations, and the selection of a fan isolation, or "closing door," system. Field testing has shown that poorly designed systems may produce large pressure losses between the shaft and fan inlet, as well as air turbulence problems which adversely impact fan efficiency and sometimes fan structural integrity. This paper analyzes each component of a surface exhaust fan system for an underground coal mine: • The shaft collar arrangement, • The 45 or 90-degree turning duct that isolates the fan motor from the return airstream, • Alternative ductwork arrangements for parallel fan installations, • The self-closing doors or dampers that are required for multiple fans, and • Horizontal and vertical evas6 arrangements on the discharge side of the fan. While discussion is limited to axial fan installations at shaft mines, most of the recommendations would also apply to centrifugal fan installations and to main mine fans for drift mines. FEDERAL REGULATIONS The mandatory safety standards for underground coal mines that apply to the installation of main mine fans are listed in 30 CFR Part 75.310. Stipulations which impact the design of the fan sys- tem arrangement are contained in paragraphs (a)(l), (a)(5), (a)(6),(d), and (1) of 75.31 0: • Each main mine fan shall be installed on the surface in an incombustible housing; • Each main mine fan shall be protected by weak walls or explosion doors in direct line with possible explosive forces; • Explosion doors or weak walls shall have a cross-sectional area at least equal to the area of the return air shaft or drift opening through which the pressure from an underground explosion would be relieved; • Each main mine fan shall be offset by at least 4.57 m (15 feet) from the nearest side of the mine or shaft opening; • Automatic closing doors shall be provided to prevent possible air reversals through the fans in mines ventilated by multiple main mine fans. The installation of main mine fans underground is prohibited by 30 CFR Part 75.310, (a)(l). Providing explosion doors or weak walls in line with a possible underground explosion and offsetting the fan 4.57 m (1 5 feet) from the edge of the shaft preclude the installation of the fan directly over the shaft. In addition, 30 CFR Part 75.507-1 specifies that all electrical equipment used in return air courses be permissible, which requires locating the fan motor outside of the airstream exhausted through the fan. To comply with the Part 75.310 regulations, explosion doors are typically located directly over the shaft as part of the shaft cover or 'bonnet." A sufficiently long section of ductwork placed between the shaft enclosure and fan, equipped with a 45 or 90- degree turn, enables the fan to be offset at least 4.57 m (1 5 feet) from the shaft and the motor to be isolated from the airstream. The need for the turn in the ductwork can be eliminated by driving the fan from the discharge side, instead of from the inlet side, and providing for a 90-degree bend in the evas6. For multiple main mine fan systems, self-closing doors can be located on the inlet or discharge side of the fan. FAN SYSTEM COMPONENTS A poorly designed exhaust fan arrangement will produce turbulent conditions at the fan inlet and significant pressure losses between the shaft and fan. Field tests have shown that pressure losses through inlet ductwork at some installations may constitute as much as 30 percent of the total mine head. Unfavorable flow conditions may cause a change in the operating point on the fan performance curve, resulting in reduced fan efficiency and pres- sure generation capability. In some instances, poor airflow distribution through the fan may create mechanical stresses that lead to fan blade or fan housing fatigue failures. The objective in designing an air duct arrangement for a fan system is to provide a low cost duct that will move the air from the shaft to the fan in a uniform air distribution and with minimum energy requirements. The optimum solution is a compromise between technical and economic factors. Aerodynamic design considerations for the shaft collar and cover, fan inlet ductwork for both single and parallel fans, self-closing doors, and evas6 are discussed in the sections below. Shaft Collar/Cover To prevent excessive turbulence and non-uniform air distribution through the fan, a smooth transition for the change in direction of airflow at the top of the shaft must be provided. However, the concrete lining of the shaft is abruptly terminated at the surface at many coal mine installations (see Figure I), creating a sharp 90-degree bend. The airflow exiting the shaft becomes heavily concentrated in the upper portion of the horizontal fan in-

Jan 1, 1997

By Thomas L. Hurst, Joseph M. Hans

INTRODUCTION The former Shiprock uranium mill site is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the mill site are located on the Navajo Indian Reservation. The millsite was built on a 230 acre tract leased by Kerr-McGee Oil Industries Inc., and was operated from 1954 to 1963. The Vanadium Corporation of America and its successor, the Foote Mineral Company, operated the mill from 1963 to 1968. During its entire operation, 1.5 million tons of uranium ore was milled producing 3711 tons of U308 concentrate. The concentrate was sold to the former U.S. Atomic Energy Commission. During milling, the ore was crushed to less than 35 mesh and acid leached to remove the uranium. The [ ] uranium was removed from the leach solution by solvent extraction and the uranium-barren solution discharged into raffinate ponds for disposal by evaporation and seepage. The spent solids (tailings) were pulped with waste process fluids and water and discharged to form tailings piles. The piles (ponds or dams) were formed with earth starter dikes. The dike walls were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. Since only a small fraction (0.25 percent) of the ore was U308 by weight, most of the ore bulk ended up as wastes. The wastes contain nearly all of the uranium decay chain radionuclides present in the ore except uranium. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and wastes reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a Tribal enterprise. In order to provide skilled personnel to operate earth moving equipment, a heavy equipment operator's training school was also established on the mill site and was administered and operated by NECA. The U.S. Public Health Service (PHS) and the Environmental Protection Agency (EPA) staff conducted radiation surveys at four inactive uranium millsites on the Navajo Reservation in April 1974. During the survey of the Shiprock millsite, it was noted that the training activities were degrading its radiological condition. Both the PHS and EPA staff recommended that the training activities be directed towards the decontamination of the millsite area and interim stabilization of the tailings piles. Preparation for the decontami-nation work commenced in April 1974. In order to facilitate the decontamination activities, the mill site and its contaminated environs were divided into major areas labeled A through F (Figure 2). Areas A, B, and C are defined as "perimeter" areas and contained surface contamination ranging from 5 to 30 cm deep. Area D defined the mill yard and contained contamination ranging from 0.6 to 5.5 m deep. Area E contained several raffinate ponds which were removed to line up the northwest boundary of the tailings pile and to move the contaminants away from the vicinity of the occupied on-site buildings. The contaminants in Area E ranged from 0.05 to 5.5 m in depth. Area F encompassed the ore storage yard. Contaminants in this area ranged from 0.18 to 1.2 m deep. Washes, however, had contamination exceeding 7.6 m deep.

Jan 1, 1981

By M. Sadegh Safarzadeh, Erich U. Petersen, Jan D. Miller

"An acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2•4H2O, PbSO4 and Cu0.47Fe0.53SO4•H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 hours with a sulfuric acid-toconcentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different concentrations. The purpose of this paper is to present our examination of the effects of sulfuric acid dosage on the extractions of Cu, Fe, and As from an enargite concentrate. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.IntroductionThe occurrence of enargite (Cu3AsS4) in copper ores and concentrates and the associated high arsenic values in such resources have resulted in a considerable decrease in the demand for such concentrates because they cannot be economically processed using conventional technologies such as smelting and atmospheric leaching (Mihajlovic et al., 2011). The exploitation of such problematic deposits through competitive treatment strategies will be required in the near future in order to satisfy increasing pressure from the copper market. It is expected that the average arsenic grade of copper concentrates will increase from 0.17% in 2008 to 0.22% by 2020 (Mayhew et al., 2011).The acid bake-leach process was identified and selected for further investigation at the University of Utah as a possible process alternative for the treatment of enargite concentrates. In this case, adequate amounts of concentrated sulfuric acid are mixed with the concentrate and heated to the temperature range 150-300°C. Subsequently, the baked material is leached with water/weak acid and the acid bake-leach process has some advantages over conventional sulfuric acid leaching (Prater et al., 1970). During water leaching, metal sulfates are released in solution, after which they can be extracted through well-known hydrometallurgical techniques. While the majority of the work has been done on oxide minerals, there is a limited record of sulfuric acid baking of sulfides."

Jan 1, 2015

By Janet A. Johnson, T. B. Borak, K. J. Schiager

INTRODUCTION In the USA regulatory agencies have adopted standards which limit the allowable concentration of ore dust in underground uranium mines. The American Conference of Governmental Industrial Hygienists has recommended a threshold limit value for silica which has been incorporated by reference in federal regulations (30 CFR 57, 1980). The Nuclear Regulatory Commission (NRC) imposes a limit for unprocessed uranium ore dust for reducing the exposure to radioactive materials from inhalation (10 CFR 20, 1980). We have been unable to trace the origin of the NRC standard. Recently the ICRP has published recommendations concerning limits for intakes of radionuclides by workers (ICRP, 1979). We have used the ICRP methodology to compute the dose equivalent commitment to lung and bone from inhalation of insoluble ore dust particles. These values were used to derive air concentrations which would provide an acceptable risk for induction of cancer from occupational exposure. Results indicate that the new ICRP recommendations are more restrictive than the present NRC standard for radioactivity. The maximum allowable dust load in a uranium mine will depend on both the concentration of silica (% Si02) and the amount of radioactivity (% U308). We have combined these standards assuming complete independence of biological hazard to establish boundary conditions for which either silica or radioactivity is the dominating factor. Based on these results we present suggestions for analysis of ore dust to insure compliance with regulatory agencies. SILICA STANDARDS Silicosis, fibrotic lung disease produced by crystalline silica, was one of the earliest forms of occupational disease to be recognized. The pulmonary lesions caused by silica, silicotic nodules, consist of concentrically arranged bundles of collagen fibers. Fusion of these nodules results in progressive massive fibrosis causing alveolar changes which decrease ventillation and blood flow in the lungs. The current Threshold Limit Value (TLV) for mineral dusts is based on the concentration of free silica. The standard is expressed in three forms: (1) Particle count standard: TLV (mppcf) = 300/(% Si02 + 10) (mppcf = million particles per cubic foot) (2) Respirable dust mass standard: TLV (mg/m3 ) = 10/(% respirable Si02 + 2) (3) Total dust standard: TLV (mg/m3 ) = 30/(% Si02 + 3) The most commonly used form is the respirable mass standard. These curent values for silica are based primarily on epidemilogical studies of Vermont granite workers and other occupationally exposed workers. In the Vermont study no cases of silicosis were seen in individuals employed after dust control measures were initiated and whose subsequent exposure averaged less than 5 mppcf. The free silica concentration in the airborne dust to which these workers were exposed averaged 25%. A concentration of 10 mppcf of granite dust is considered equivalent to 0.1 mg/m3 quartz. The current respirable mass standard allows a maximum silica concentration of 0.1 mg/m3. NIOSH (1974) has recommended a reduction in the current TLV for respirable silica to 0.05 mg/m3 Si02. As with radiation standards, the TLV for mineral dusts is an upper limit for time weighted average exposure. It is recommended that dust concentrations be maintained as far below the TLV as current practices permit. RADIATION STANDARDS The present concentration limit for airborne natural uranium in ore dust prior to chemical separation is 75 µg of uranium per m3 of air ( 10 CFR 20, 1980) . This corresponds to 1.85 Bq/m3 (50 pCi/m3 ) of natural uranium, U-238, U-235 and U-234 and is equivalent to 3.7 Bq/m3 (100 pCi/m3 ) of gross alpha activity with radioactive equilibrium between the long-lived alpha progeny through Ra-226. The origin or basis for this standard is not known, but it presumably includes both chemical toxicity and risk from somatic radiation injury. Recently the International Commission on Radiological Protection (ICRP, 1977) has published recommendations concerning the objectives and criteria for limiting radiation exposures. This was followed b y a revision of the limits for intake of radionuclides by workers (ICRP, 1979; ICRP, 1980). The previous compilation of limits for internal emitters was published by ICRP Committee II in 1959 (ICRP, 1959). The latest version includes new methodlogy outlined in ICRP Publication 26 (ICRP, 1977) as well as extensive metabolic information

Jan 1, 1981

By Robert M. Abrams

The passage of an ore pulp through the froth flotation process results in the production, after dewatering, of a finely divided concentrate. This intermediate product Trust be handled to the subsequent process facilities via belt or other types of conveyors, hoppers, bins, chutes and feeders, and the like, Flotation concentrate has some difficult handling properties such as abrasiveness, sluggishness when moist, or fluidity when dry, These characteristics require the judicious selection or design of handling, equipment and the careful engineering of transfer chutes. It is to the special problems which are encountered in this in-plant handling procedure that this paper is addressed. The methods which will be discussed have beer. developed primarily for the handling of the froth flotation concentrates of copper, leap, and taconite iron ores, but may be generalized, with appropriate modifications, to apply to other similar metallic concentrate&. The controlled feeding of concentrates frog: bins and hoppers is covered alone with some of the techniques used to transfer concentrates from ore belt conveyor to another. Methods are described for unloading belt conveyors into bins or storage tiles, The reclamation from storage piles is also treated.

Jan 1, 1976

By W. S. Fyfe, G. Southam, T. J. Beveridge

Sporosarcina ureae was able to grow in the presence of tip to 10-ppm L-asparagine complexed gold. However, 10 ppm Au3+ was found to be highly toxic to Sporosarcina ureae, killing 109 bacteria/mL within a few seconds. To compare the effects of these responses on gold mobility, an in vitro bacterial biofilm model was developed to examine the interaction be¬tween Sporosarcina ureae and ionic gold or L-asparagine gold complexes in gravity fed columns. The immobilization of ionic gold was between 80% and 90% over a period of one week. But, as the available cellular reactive sites became saturated, immobilization decreased to 14% within two weeks. In the L¬asparagine-gold system, gold immobilization in the cytoplasm occurred at a high rate (80% to 90%) throughout the experi¬ment, with limited toxicity towards Sporosarcina ureae. The bacterial immobilization and detoxification of L-asparagine¬complexed ionic gold was associated with a low molecular weight, i.e, <5,000 dalton (atomic mass unit), intracellular protein fraction. This peptide-complexed gold would allow for the continued biogeochemical cycling of gold under ambient (<100°C) surface or near-surface conditions.

Jan 1, 2000

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By R. V. Ramani

This paper is based on the thesis that the demand for computer-oriented mining engineers will continue to sharply increase in coming years. It presents the philosophy behind the development of a mine systems engineering program at The Pennsylvania State University. The paper discusses the current status of mining engineering education and the problems encountered in integrating extensive computer background and education into a traditional mining engineering program. The paper analyzes the interrelated roles of research, graduate studies, and continuing education in developing a comprehensive program of study. It is hoped that this program philosophy will be useful to other institutions which are contemplating new programs and courses in emerging technologies.

Jan 1, 1982

By Ralf Plinninger, Pafos Busch, Richard Gradnik

This paper presents the details of the Bad Bergzabern tunnel project. This tunnel is the main part of the B427 federal road bypass, intended to improve the regional traffic infrastructure and to reduce the traffic load in the historic city centre of the health resort Bad Bergzabern. Located in the south-western part of Germany, the project area is situated at the eastern margin of the so-called Palatinate Forest, a low mountain region of mainly triassic sediments with a complex and variable geological history. The German federal government, represented by the office of mobility of Rhineland- Palatinate, awarded the contract to BeMo Tunnelling, a specialized Tunnelling company with a long history of innovation and success in NATM tunnelling. The contract includes the construction of two separate tubes with a length of approximately 1,44 km (0.9 mi)—the road (main) tunnel with a cross section of 101 m2 (1,090 sq ft) and a parallel rescue tunnel with a cross section of ca. 23 m2 (250 sq ft.) Both are connected by six cross passages. Tunnels and cross passages are excavated according to the principles of the New Austrian Tunnelling Method (NATM). Due to BeMo Tunnelling’s technical expertise and capabilities, the project team was able to engineer a speed-up concept that saves money and time for the construction team and client. This paper presents the innovative approach BeMo Tunnelling made to optimize the execution of the tunnelling works and the challenges the project team is facing with regard to a complicated geological situation, countermeasures against an increasing effect of climate change and volatile prices for construction materials.

Jun 13, 2023

By Ing. Ludwig Schlebusch

The significant growth of the world population and its demand for an increasing standard of living leaves no other choice than continuously augmenting industrial production and making available steadily greater quantities of raw materials at still better qualities. Therefore, any raw material has to be utilized to the greatest possible extent and processed at optimum economy on large mechanical equipment. The layout of processing facilities of large throughput rates can be based on multiple or single lines. The latter enables the application of large machines of optimum size. Proven equipment for homogenizing, classifying, separating superfine material, sorting and dewatering are-now available in optimum sizes. By the use of these large machines operating cost of pit coal preparation plant can be significantly lowered by reducing the specific requirements regarding space, capital investment, energy, operation and maintenance.

Jan 1, 1980

By Jeremy Cawley, Horry Parker Jr., Clint Wilson

The 5180 m EPBM drive on the Lower Olentangy Tunnel (LOT) is predominantly within glacial overburden. To connect LOT with the existing OARS deep tunnel in limestone bedrock, the upper 15 m inside diameter Vine Street retrieval shaft telescopes down to 6.7 m in diameter and extends into the karstic Columbus Limestone to a depth of 51 m, where a 104 m SEM tunnel will connect to OARS shaft 6. Pre-excavation grouting was reuired prior to lower shaft excavation to reduce potentially high groundwater inows. This paper discusses the secant pile installation, grouting program, shaft excavation, and hydrogeologic observations.

Jun 23, 2024

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By D. W. Park

Geologic condition is one of the most important factors for longwall mining operations, especially, the existence of faults limits the mineable area, or cause stress variations at the longwall face. Recently, a longwall panel passed through a fault at the Shoal Creek Mine of Drummond Company, Inc. The fault was situated diagonally along the longwall face and the coal seam was displaced up to 2.4 m (8.0 ft) in a mode of a normal fault. LoSCoMS (Longwall Strata Control and Maintenance System) was used for monitoring shield pressure every minute and interpreting data in terms of setting, developing and final pressures. The results of the analysis regarding the influence of the fault on the shield pressure are presented.

Jan 1, 1999

By T. C. Vogt

Earlier we described the uranium mineralogy of an areally broad sampling of Crownpoint ore, including the characterization of organic carbonaceous material associated with the uranium mineral. (1) We also reported on the leaching behavior of Crownpoint ores with a mild alkaline leaching system, oxygen (02)-sodium bicarbonate (NaHC03). (2) There was a wide range of leaching responses, with samples from some areas leaching at a slow rate with low uranium recovery. Evidence indicates that in these samples the organic material is intimately associated with the uranium mineral and shields it to some extent from contact by the leachate. (1,2) One method to obtain faster leach rates and higher recoveries is to use a chemically severe leaching system such as sodium hypochlorite (NaOCI) as an oxidant. (3) The use of sulfuric acid (H2SO4) and an oxidant for leaching ore in surface milling operations is widely practiced to effect high recovery of uranium (U308) from the ore. (4,5,6) The U308 is mobilized as the disulfate complex, U02(S04)224-, or possibly, the trisulfate complex, U02(S04)34-, is the soluble species. (7) Sulfuric acid leachate formulations were used in the first in-situ leaching operation in the Shirley Basin in Wyoming. (8) More recently H2S04 formulations have been used in the Rocky Mountain Energy field tests in the Powder River Basin (Bear Creek) and in the Teapot forma¬tion at Nine Mile Lake site near Casper. (9,10) Laboratory studies related to the use of H2SO4 for in-situ leaching have been reported (11-17) and Yan has .reported packed column leach studies on Crownpoint ore using H2504 and oxidant. (18)

Jan 1, 1981

By W. C. Hellyer

In an autogenous grinding circuit in which feed at approximately nine inches top size is reduced to a size suitable for subsequent processing, the build- up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge. 9, (1) The buildup of a "critical size" fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large diameter steel balls to the grinding charge. This has certain disadvantages, such as; (i) an increase in mill liner wear; (ii) wear on the steel balls, and; (iii) some loss in flexibility in grinding circuit operations resulting from difficulties in removing the steel balls by means other than by grinding out.

Jan 1, 1970

By E. C. Winegartner

In producing and selling coal, the coal company is faced with many different parameters by which the quality of its product is evaluated. One type, which we choose to call the economic parameters, includes moisture, ash, sulfur, and Btu&apos;s. These are reasonably well understood by both the coal supplier and the customer, and the dollar values can be placed on them. This is the group of parameters of primary interest to most purchasing agents buying coal. A second group of parameters governs how the coal will behave in the boiler itself and is of primary concern to the engineers designing the boiler and to the men who must operate and maintain it. Since we have not yet learned to put dollar values on these parameters, they generally show up in coal contracts simply as cutoff points, the purchaser simply saying that he will not accept coal outside of certain limits.

Jan 1, 1975

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993