Search Documents

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By Bruce K. Cantrell

As part of a continuing study of diesel exhaust aerosol characteristics, the Bureau of Mines has applied Chemical Mass Balance (CMB) model source apportionment analysis to evaluate a size selective sampling method for determining the separate diesel exhaust and coal dust aerosol concentrations in a diesel equipped coal mine. Size selective sampling was used under the premise that diesel exhaust aerosol dominates the submicrometer aerosol size range, while most of the mineral dust aerosol is greater than 1 m. A micro-orifice, uniform deposit impactor (MOUDI) was used as the size selective sampling method. Concurrent samples of mine aerosol were collected using a dichotomous, respirable aerosol sampler. This sampler separated the fine and coarse size portions of its sample at 0.7 m. Trace element concentrations for in-mine aerosol sources and the dichotomous samples used by the CMB model were measured using Instrumental Neutron Activation Analysis. The CMB analysis, applied to both the fine and coarse fractions of the respirable mine aerosol, yielded the mass concentration contributed to each by diesel exhaust and mineral dust aerosol sources. The MOUDI size distribution data were analyzed using nonlinear regression to parameterize the fine and coarse fractions of the sampled aerosol and to estimate the contributions to each fraction from both coal dust and diesel aero- sol sources. For the diesel mine visited, analysis of the MOUDI samples yielded a value for the fraction of the fine aerosol attributable to coal dust of 15[]7% fine fraction coal from analysis of the MOUDI samples versus 25[]4% from the CMB analysis. The remainder of the fine aerosol in the mine was diesel exhaust aerosol. CMB analysis confirms the original premise for such sampling. After correcting for the presence of coal dust in the fine aerosol fraction, analysis of the MOUDI size distributions yielded estimates of respirable mineral and diesel exhaust aerosol concentrations that were accurate to with-in 10% of values determined by the CMB apportionment.

Jan 1, 1987

By Gordon T. Clark

The preliminary design of four mined stations and 7.2 km (4.5 miles) of tunnels for Seattle’s light rail transit system is described. Constraints that influenced the design and options that were studied are discussed. The hilly post-glacial soft-ground geology of the Puget Sound Region pushed the alignment deep. Mined underground stations at depths up to 75 m (250 ft) and shafts with excavated diameters of 20-m (65-ft) are required. A 460 m (1,500 ft) sub-aqueous crossing of Portage Bay and undercrossing of an active 12-lane multi-level freeway were two of the more significant design constraints.

Jan 1, 2001

By Garry G. Lowder

The regional geologic setting is essentially a volcanic island arc built upon an oceanic basement, consisting of basalt and minor pelagic sediments (the Tinombo Formation of Eocene - lower Miocene age. Trail et. al. 1974). -- An east-west chain of intermediate and acid calc-alkaline volcanoes (the Bilungala Volcanics) was built on the oceanic basement during the Miocene. The Bilungala Volcanics are flanked to the north largely by contemporaneous andesites and volcanoclastic sediments of the Dolokapa Formation. During middle to upper Miocene time the Bilungala Volcanics were invaded by large masses of predominantly dioritic intrusive rock and it is within one of these dioritic intrusive complexes, the Bone Diorite, that the cluster of porphyry copper systems occurs. Renewed volcanic activity in the Plio-Pleistocene produced acid pyroclastic rocks (the Pinogu Volcanicsi whose distribution is controlled by present-day topography. Structural trends, largely interpreted from SLR imagery, are pre- dominantly NW or NIWJ. The right-lateral Gorontalo Fault, which trends hW through the town of Gorontalo (Katili, 19691 is the most prominent structural feature. Many of the major structures in the Tapadaa district have similar orientations and may be sympathetically related to the Gorontalo Fault.

Jan 1, 1976

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

The Mesquite mine is being operated by Gold Fields Operating Co.-Mesquite, a subsidiary of Gold Fields Mining Corp. The mine Is located in southeastern California about 56 km (35 miles) east of the farming community of Brawley, California. The mine has been in commercial production since early 1986 and Is a conventional open pit mine developed on 6.1 m (20 foot) benches. The gold is recovered by heap leach using permanent heaps built in multiple 6.1 m (20 foot) lifts. This year's gold production will be in the range of 5,600 kg (180,000 troy ounces). Current ore production is about 18,140 tonnes (20,000 tons) per day while the total tons mined Is averaging 65,000 tonnes (72,000 tons) per day. The climate at the mine is extremely arid with rainfall of 7.6 cm (3 inches) per year. From early May until late October daytime temperatures generally exceed 37.8 degrees Celsius (100 degrees Fahrenheit) and can be as high as 37.9 degrees Celsius (120 degrees Fahrenheit).

Jan 1, 1989

By D. J. Pandelis, W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By P. D. Chamberlin

The interface between precious metal miners and gold refiners has been an uneasy interface over the years. The reasons for this interface and its apparent uneasiness and lack of trust include technical factors, economies of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates and sponge produced at the mine site are notoriously difficult to sample and a non-representative sample can be the cause of misunderstanding and distrust. Dore, however, is homogeneous and can be correctly sampled and analyzed. Second, the technology and chemistry of fine gold and silver production is complex and quite different from that of dore production. Most mining companies are content not to be involved with additional processing steps.

Jan 1, 1986

By Leon J. Jacobs, Kyle R. Ott

This paper discusses design and construction aspects of the tunnel, shaft and station for the Weehawken Tunnel and Bergen line Avenue Station. The project consists of a 1,269 m (4,156 ft) long existing railroad tunnel, which will be enlarged and equipped with a two-track light rail system. The project also includes construction of a deep underground station, with a large shaft connecting the surface station to the below ground station for access and ventilation purposes. Vibration and noise from blasting is a critical community issue and blasting adjacent to two 230-kV duct banks located in the tunnel invert required special blasting procedures.

Jan 1, 2003

By V. T. McLemore

The Wind Mountain (WM) nepheline syenite deposit is part of the alkalic complex in the Cornudas Mountains, which ranges in age from 34.6 ± 1.5 Ma to 36.8 ± 0.6 Ma. The WM deposit consists of a complex, zoned pluton that ranges from syenite porphyry to nepheline syenite porphyry. The WM deposit has potential use for ceramics and dark-colored beverage containers and consists of nepheline, k-feldspar, albite, and varying amounts of other minerals. Analcime also is present locally but must be avoided because it is unsuitable for ceramic and glass. Chemically the deposit consists of 56-63 % SiO2 17-21 % Al2O3 and 4.0-5 % Fe2O3. Although initially iron is high, when the crushed rock is passed through a specialized magnetic separator, the iron content drops to below commercial maximum standards of less than 0.5% Fe2O3. The WM deposit is currently under exploration and testing to determine marketability.

Jan 1, 1994

By D. D. Murphy

The Bureau of Mines has studied the mechanism of shear-flocculation of silica with stearic acid. At pH 6 and 12, shear-flocculation of silica was not observed with up to 10-4M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations 10-4 M (5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labelled with a doxyl group. The presence of the spin-labelling group did not greatly affect the shear-flocculation properties of stearic acid. Adsorption of labelled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicate the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-414 (5 lb/st). The results are discussed in terms of a possible mechanism for shear-flocculation.

Jan 1, 1993

By E. C. Roper

Landusky Mining, Inc. and Zortman Mining, Inc. are two registered Montana Corporations wholly owned by Pegasus Gold, Ltd. of Vancouver, B.C. The Zortman and Landusky Mines are located in the Little Rockies District of central Montana. The Zortman-Landusky mines produced 2,100 kg gold in 1982. A total of 3,250,000 t of ore per year are mined during the period March 1, to September 15, at an average grade of 1.04 gm/t (0.03 oz/t) gold and 13.4 gm/t (0.385 oz/t) silver at a cutoff grade of 0.35 grams of gold/ton (0.01 oz of Au/t) of ore. The stripping ratio during 1983 is anticipated to be 0.75/1 waste to ore. Combined average plant capacity of the two Merrill-Crowe plants is 9,840 lpm (2,600 gpm). The combined heap spray capacity of the two plants approaches 18,900 lpm (5,000 gpm). The mine employs approximately 200 people, about half of these work for the mining companies and the other half for the mining contractor, N. A. Degerstrom of Spokane, Washington. Net profit in 1982 for Zortman and Landusky Mining, Inc. approximated $4,900,000 at an average gold price of $11.40/gm.

Jan 1, 1983

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By J. Chai, Y. Qiang, D. D. Zhang

"In order to control Quaternary loose layer settlement in East China, there are monitoring results based on the 3 water level observation holes and 7 sand layer of fiber Bragg grating (FBG) strain sensor. Un-der the conditions of upper group water injecting to lower group of loose layer, the deformation characteristics of upper, middle and lower group of loose sandy soil layer changing with time and relationship with the water level are studied. The constitutive relation of stress-strain is also studied at different sand layers. Research results show that using water injecting from upper group into lower group of loose layer can ease the loose layer compression deformation. With the water level dropped, in East China soil creep deformation occurred, which accord with viscoelasto plastic model. The deformation of lower sand group has clear later effect and no direct relationship with water level. The results provide an important basis for the study East China stratum settlement model and water management. INTRODUCTION Ground-surface subsidence is a common geological disaster, which has the features of continuous, changing slowly, concealment (Y.P. Yin et al. 2005). Today, due to underground mining and constructions in formation compression, surface subsidence is wide-spread in the world, which is the environmental geological problems in the worldwide that cannot be ignored (Y.Q. Xu et al. 2006, D.L Gallo-way et al. 2000, Qiu, B. et al. 2011). The eastern region of China has generally geological disasters in coal mine geological caused by the thick loose layer settlement like as mine shaft failure. Stratum dehydration consolidation is a major cause of loose layer settlement (H.Y .Liu et al. 2007). A method of water injection using ground water to stable water level is proposed, which can effectively control the loose layer caused by compression settlement(J. Chai et al. 2012&.2013). Accurately knowledge the characteristics of strata deformation is the premise of settlement management (Q.C. He et al. 2006). Previous re-search (J.F. Miu et al. 1996, X.Y. Gu et al.1998, Y. Zhang et al. 2006), mainly studies are focused condition of the city pumping irrigation, de-formation characteristics of middle and up loose layers. On a group of aquifer in East China, the loose layer losing water is caused by coal mining, bottom water drainage and overlying strata water flowing fractured zone hydrophobic induced by mining, which the dehydration conditions have great difference from one to another. The Position of water loss is centralized in bottom aquifer, and the formers of ground subsidence geological environment and settlement mechanism are different. According to the study of stratum settlement, usually the de-formation of sand layer is ignored(C.H. Liu et al. 2004), but few studies show that the sand layer have the plastic deformation, and contains the creep deformation, water content of sand soil may become the main settlement layer (Z.X. Wei, 2002, C.H. Liu et al. 2004)."

Jan 1, 2015

By P. Kim Carroll, D. Nick Tiffany, Doyl M. Fritz

Thunder Basin Coal Company received the 1987 Wyoming Excellence in Surface Mining Award for construction of the State's first major sediment control reservoir to be designed using the new settleable sol ids standard. Use of this standard resulted in construction cost savings of more than $250,000; reduced water quality monitoring; enhanced downstream channel stability because of more natural sediment loading; allowed simultaneous establishment of permanent waterfowl and fisheries habitat; and provided a quality recreational site. This article will address factors associated with the design and construction of that sediment reservoir and the benefits that were realized. (Note: This paper was originally published in the proceedings for the 1988 National Symposium on Mining, Hydro1ogy, Sedimentology and Reclamation held in Reno, Nevada, December 5-9, 1988.)

Jan 1, 1989

By Thomas A. Palmer

Free cyanide has been successfully determined in ground and surface water by isolation using a microdiffusion technique followed by a pyridine-barbituric acid photometric finish. The determinable free cyanide includes hydrocyanic acid, ionic cyanide, and the cyanide of weak complexes such as cadmium, lead, manganese, and zinc cyanide. Complexes of copper, iron, nickel, and silver are sufficiently strong so the dissociation into free cyanide does not occur at the microdiffusion pH 7. Cyanate, sulfide, and thiocyanate do not interfere. Samples containing as little as 0.005 mg/L are successfully analyzed. The relative standard deviation is <10%. Samples stored at pH >I2 in the dark are stable at least three weeks.

Jan 1, 1981

By Abhiram Kumar Verma, Soumya Ranjan Mallick

Generally, waste such as soil and sandstone is used in mines for road construction or haul roads. In many such mines, it is challenging to design haul road pavement to match the dumper capacity. This paper investigates overburden soil to find its utility as a pavement material. It is found that overburden soil is unsuitable pavement material without stabilization; hence, nine composite materials are developed using overburden soil and RBI. Physical, mechanical and microstructural properties of unstabilized and stabilized soil are determined. Statistical analysis is carried out to assess the effect of soil type, RBI and curing period of strength characteristics of unstabilized and stabilized soil. ANOVA tests assess the influence of RBI percentage on soil geotechnical properties, and regression relations are developed. Two-way ANOVA shows the effect of RBI and soil type on soil geotechnical properties, whereas one-way ANOVA shows that the influence of soil type is more than the RBI. The regression relation is developed for CBR, UCS, Poisson’s ratio and modulus of elasticity with a good correlation coefficient. The performance of RBI is more with the finer material and reduces with an increase in the size of soil grains. The performance of the developed composite is better than the earlier developed composite based on overburden with fly ash, lime kiln dust, lime or clinker.

Mar 19, 2024

The Ernest Henry copper-gold project is located in North West Queensland, Australia and commenced production in late August 1997. Utilizing a philosophy of selecting the biggest proven equipment available Ernest Henry at full production ¥ill treat 9 Mtpa through a single grinding line over a 15 year mine life. 350.000 tonnes of concentrate a year will be produced, containing 95,000 tonnes of copper and 120,000 ounces of gold. The two mills recently commissioned at the Ernest Henry Copper/Gold Mine are a 10.4m x 5.1m (34 ft x 16.75 ft) SAG Mill and a 6.1m x 8.4m (20 ft x 27.5 ft) ball mill. The mills have a power draw of 11 MW (14745 hp) and 5.5 MW (7373 hp) respectively. While the SAG Mill is not the largest SAG Mill in the world, it is the largest shell-supported SAG Mill in the world. The Ernest Henry mills epitomize the new standard design of large grinding mills. The design was introduced more than 20 years ago and has been further developed from extensive experience with grinding mills, and the need to produce a design, which overcomes the recognized problems of large mills. The result is a design with the potential to be used for mills up to the largest for which machine tools can be found to fabricate and machine them, currently approximately 15m (48&apos;) overall diameter.

Jan 1, 1999

By Joe Keane

DOUG HALBE: The kickoff speaker, and my unanimous choice, is Joe Keane. Joe was born in Butte, Montana, and began his association with the mining industry as an under- ground miner at age 16. Currently he is president of KD Engineering and Metcon Research. He had it lucky when he went to school because there were only 44 elements in the periodic table, I understand. [laughter] Here&apos;s Joe. JOE KEANE: I&apos;m doing this under protest. Maybe we can start the slides. Mr. Halbe gave me this topic, but I don&apos;t like it. I don&apos;t like Mr. Halbe either [laughter] because of the way he shanghaied me into this. He called me up on the phone and said this is what you&apos;re going to speak about: "Five Things I Never Want to See Again in Plant Design," and I said, "Huh!" Then I started getting stuff from SME about how to make a presentation. I have decided to change the title to "More Than Five Things I Never Want to See in Plant Design," since you can&apos;t have a completely negative speech; you have to have other topics. So we will have some other, not completely nonrelated, topics to sort of break the tension. I tried to find a joke to open with. I talked to Omar Mutati. All of his jokes were either about Bill Clinton, our beloved President, or they were too filthy to say in a mixed group. [laughter] So I decided to start this out with a profound statement. The pro- found statement is, "The meek shall inherit the earth, but not the mineral rights," [laughter] by J. Paul Getty. J. Paul Getty was one of my favorite guys because when a real obnoxious reporter asked him one day, "How can I become wealthy?" he said, "Drill for oil and find it."

Jan 1, 1998

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003