Search Documents

By R. V. Ramani, R. Bhaskar

While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mine environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use. As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined. The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.

Jan 1, 1987

By L. W. Cope

Cuba is a mineral rich area, and the Cuban government is encouraging mining investment in the country. Joint ventures with government entities are encouraged. This paper will give some insights into the laws and regulations, and the agencies to contact for investment and development. The present-day situation of the US sanctions against Cuba will be covered.

Jan 1, 2004

By Phil Shelton

What exactly does clean coal mean? Mining coal creates dust and releases methane gas. And burning coal liberates CO2 and emits particulates, including SO2 and NOx. Coal creates wastes that are often stored in unsightly and potentially dangerous slag heaps and lagoons. When clean coal technology is discussed, it sometimes seems that creating modern or ?ultra super critical? coal-fired power stations is presented as the main or even the only answer. However, there may be a more holistic approach. Using the energy potential of coal is always going to have environmental impacts. Some of these will be negative. But the need to secure future energy resources demands that society tackle these negative issues and find ways to minimize and offset them.

Jan 1, 2010

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electric field (E-field) sensing to send text based communications using two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multi-site evaluation of available TTE systems in an effort to determine their operational sensitivity. INTRODUCTION Wireless, Through-the-Earth (TTE) communication technology is designed to achieve point to point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. This ability allows TTE communication to function without the need for intermediary communications infrastructure, such as repeaters. As a result, such communication systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers 1924; Pittman, Church and McLendon 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker 2006; Wadley 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer 1973; Geyer and Keller 1976; Geyer, Keller and Ohya 1974; Jakosky and Zellers 1924; Large, Ball and Farstad 1973). Although commercially developed TTE systems have demonstrated the ability to communicate through a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker 2006; Geyer and Keller 1976; Geyer, Keller and Ohya 1974; Ilsley, Freeman and Zellers 1928; Jakosky and Zellers 1924; Yenchek et al. 2012)."

Jan 1, 2016

By Ari Glazer

"Every year the tunneling business is expanding and collaboration with the International Society of City and Regional Planners (ISOCARP) for the future design of cities and urban communities is in the making. During the last half of this century, billions of people migrated to cities, and it is estimated that by 2030 almost five billion people worldwide will reside in urban communities. Hence, “Underground development will be an important tool in reshaping our urban areas to meet the challenges of the future without destroying their heritage or worsening their surface environment” (Esaki, 2005). In 2013, the Organization for Economic Co-operation and Development (OECD) estimated life expectancy to be around 80 years, meaning that in less than a decade we will need to bury billions of people in cities and urban communities, while trying to retain the deceased’s beliefs and customs. Religion plays a major role in our lives, and many people worldwide still decline to cremate their body after their death; therefore, cemeteries are essential for city inhabitants. Rites and traditions usually call for burials to be near the place of residence, which allows the remaining family members and friends to visit the grave frequently, at least in the first years. This is a challenge that urban designers and architects must confront while trying to solve the problems of future urbanization. In recent years, population growth, the rising cost of land and the extensive preservation of green areas have made cemeteries a burden and a nuisance, particularly for large cities and communities. Many graveyards that were once on the city's outskirts have become lifeless islands in populated areas (Fig. 1), rarely visited by the second and later generations. Cities worldwide face the challenge of allocating less land to maintain current burial practices. In response, some cities have begun to bury their dead at a great distance from the community; others have started to stacked burials, one on top of the other, while still others are constructing buildings and even skyscrapers for the practice of burial (Fig. 2)."

Jan 1, 2016

A joint research effort by Newmont Gold and Du Pont, working with Kurtis Mooney, of Tri-Combined Resources has developed a new ore-sample bag made of "Tyvek," a spunbonded olefin. "The goal was to find a bag with the best trade-off between efficient draining of moisture, minimal fines loss and compatibility with the conveyor drying process we were developing for our new assay lab," Charles Bucknam, analytical development coordinator for Newmont Metallurgical Services states. None of the available polypropylene, cotton or canvas bags had the needed combination of properties. "Our original tests in 1987 on the plastic bags we had been using showed an average loss of 5.4% of mud sticking to the bags when they were emptied into drying pans. Part of the sample was still in the bag as a residual." Tests on bags of "Tyvek" showed low residuals when the samples were dried in the bags before they were emptied, but about 3% of the fines were lost through the seams. Mooney recommended a new bag design, with fold-over seams.

Jan 1, 1990

By J. Finch, W. Petruk, R. G. Pinard

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections to characterize a mill product and determine the apparent mineral liberation. It was found that a representative polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly, individual screened fractions are not representative of the sample because minerals are partitioned during screening, and the quantities of soft brittle minerals are increased in fine grained fractions, whereas the quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (one Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analyzing each fraction and combining the data. Somewhat less accurate data would be obtained by analyzing a series of screened fractions that have a wider size range of particles (five Tyler size ranges).

Jan 1, 1987

By P. Sotiropoulos

In the framework of the Specific Programme: ?Promoting Competitive and Sustainable Growth? a detection system was designed and developed in order to provide an added value service beyond standard instrumentation. In the hydrocarbon industry it will be possible for the first time to detect in a pulse regime, two types of radiation emissions using a single device. This means that any saturation of hydrocarbons can be detected, irrespective of the degree of formation water mineralization, which is a major limitation on currently available neutron-gamma tools, where the formation water has a low mineralization.

Jan 1, 2006

By R. V. Ramani, S. Skankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken: •a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; •a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and •the mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies, it was observed that increasing the air velocity increased the rate of re-entrainment (Shankar and Ramani, 1994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1996

By A. Anderson, G. May, C. Kubank, S. Meik

The Kori Kollo operation is owned by Empresa Minera Inti Raymi S.A., a Bolivian mining company. Inti Raymi is an eighty-five percent owned subsidiary of Battle Mountain Gold Company (BMGC). The remainder of Inti Raymi is held by Zeland Mines S.A., a Bolivian mining company. The project is located near the village of La Joya, approximately 220 km south of La Paz, and 40 km north west of Oruro on the Bolivian altiplano. Inti Raymi started a heap leach operation in 1985. By 1988, following several expansions, 4,000 tonnes per day of oxide ore were being treated. At this time drilling was started to delineate the larger sulfide orebody. A feasibility study for the development of this deposit was completed in 1990, and following project approval, the engineering design was started later that year. During this period orders were placed for the major items of mechanical equipment. In July 1991, Minproc Engineers Inc. was awarded a firm price contract to design and construct the 14,000 tonne per day sulfide ore process facility.

Jan 1, 1993

By A. D. Hammond

"INTRODUCTION Vanadium deposits in Arizona are distributed all across the state, from the rim of the Grand Canyon to the Tombstone mining district in the southeast corner of the state (Figure 1). The combined past production of vanadium from Arizona and New Mexico ranks second nationwide, after deposits in the Colorado Plateau In the northeast corner of the state, in the Carrizo Mountains and Monument Valley of Apache and Navajo Counties, vanadium was produced as a by-product of uranium in deposits of the Salt Wash and Shinarump members of the Morrison and Chinle formations, respectively. The production took place between 1943 and 1970. Another source of vanadium in Arizona occurs in vanadate deposits associated with supergene enrichment of base-metal vein and replacement deposits. The most important vanadate mineral is vanadinite, a chloro-vanadate of lead. Presently, there are no primary mines of vanadium in the United States. In 2012, a small production of vanadium pentaoxide (V2O5) was reported as a by-product of uranium at the White Mesa uranium mine in Utah1. This paper describes vanadate deposits in Arizona with emphasis in three districts, namely, the Mammoth, Globe-Miami and Banner districts.VANADIUM EPIGENETIC DEPOSITS: VANADATES Almost all vanadium epigenetic deposits occur as vanadates in oxidized zones of lead, zinc and copper veins and replacement deposits. Vanadinite, descloizite and mottramite are the most common minerals in vanadate deposits. Descloizite is a vanadate of lead, zinc and copper. Wulfenite, a molybdate of lead is also present. These minerals replace supergene base-metal minerals, form crusts on faces of open cavities, or are inter-grown with residual clays in pockets. The vanadium content in vanadate deposits is believed to have been leached from the country rock by ground-water and transported through porous rocks until precipitating as a relatively insoluble vanadium compound or until the solution evaporated. Precipitation was brought about by local concentrations of cations of divalent lead, zinc or copper. Lead is a constituent part of almost all of vanadate deposits and the vanadium pentaoxide (V2O5) content in vanadate minerals seems to have a direct correlation with the content of lead in the hypogene mineral. Vanadate deposits are restricted almost entirely to the oxidized parts of vein or replacement deposits. It is rare that oxidized zones extend past 100 ft from the surface. Vanadate deposits are largely restricted to tropical and temperate zones and regions of dry climate. Arizona and New Mexico have the largest concentration of vanadate deposits in North America."

Jan 1, 2015

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By Ronald Allum

Arizona leads all other states in the value of gemstones produced with an annual production which exceeds $3,000,000. Gemstones are an important component of the mineral wealth of the State. Turquoise, peridot, chrysocoll a, petrified wood, fire agate and crystallized mineral specimens are among the gemstones commercially mined. Numerous additional deposits are operated by hobbyists. The State's reputation as a source of gemstones and specimens for the collector and lapidary adds to the economy of the State by attracting tourists. Production of gemstones further adds to the State's economy through employment in the value added gemstone processing industries and by employment of Native American craftsmen.

Jan 1, 1988

By Chris Roos

The mining industry has made strides in planning for operations to be safe for the workforce and public, to protect the natural environment, and to maximize value for shareholders. However, many of the techniques used to accomplish these goals are based on estimated models of mineral content, production efficiency, and economic performance. The industry has begun to recognize the need for understanding the uncertainty in these models, how it affects their decisions, and what the potential impacts are for each project. The challenge has become how technical professionals can effectively communicate the impact of this uncertainty and its importance to both technical and non-technical audiences. This paper presents mining engineers (and other technical professionals) with traditional and modern principles of data visualization and technical communication that can assist with communicating the effects of uncertainty in the mine planning process.

Jun 25, 2023

By R. Bishop, J. Baggett, J. Monsalve, N. Ripepi, A. Soni

Technology plays an ever-increasing role in improving the safety and efficiency of mining operations. Laser scanning and photogrammetry are two useful methods for capturing 3D digital representations of real world objects. While both technologies have been applied to the mining industry in numerous ways, the practical applications in an operating underground limestone mine has been tested for this paper, including for visualization and site characterization. Each technology is capable of creating highly detailed geospatial point clouds, but are all point clouds created equal? This paper presents a comparison of a laser scan and photogrammetry of a limestone pillar and addresses the strengths and limitations of each method for creating digital models of operating underground limestone mines. INTRODUCTION The United States crushed stone business is a ~$14 billion per year industry representing 1,430 companies which operate 3,782 mining operations across the 50 states. In 2017 alone, 1.33 billion tons of crushed stone was produced with 76% used predominately for road construction and repairs, but also for the production of cement, lime, chemical and agricultural uses. Over 70% of domestic crushed stone producers source their material from limestone and dolomite deposits, with currently only 82 mines (2%) operating underground (USGS, 2018). Underground mining requires a different technical skillset, and poses great challenges for production that must be both safe and economical. Therefore, there are many risks that an operation must mitigate in order to produce underground limestone. Some of the challenges in underground limestone mining involve geological hazards that are unique to the rest of the industry. The geologic features such as faults and weaknesses can be difficult to assess in a production environment (NIOSH, 1998). The consequences of failure due to improperly designed underground mining ground support systems, such as from a roof failure, are not only life threatening for the miners themselves, but can easily shut down an entire mining operation.

Jan 1, 2019

By S. M. Jarrett, W. B. Schmidt

Within the last year, the Nation has been shocked by two major tunneling disasters. Almost exactly a year ago 17 men died in the San Fernando Tunnel in an explosion attributed to gas. A few months later another 21 men died in an explosion laid to the same cause at Port Huron, Michigan. The analysis of the causes of these accidents is still continuing. While it appears that they differ substantially from each other in their specifics, they share the common trait that, like most industrial accidents, they might well have been prevented. Gas explosions in tunneling are neither new nor particularly unusual. Forty years ago, Assistant Director Jarrett was hired as a safety engineer on the Hetch Hetchy Aqueduct in California after an explosion that killed 12 men. Prior to 1946, in California alone, the Bureau of Mines had recorded 27 gas explosions incidental to hard rock mining and tunneling. The purpose of this paper is to review the status of the principal regulations affecting tunneling and to indicate some ways in which safer and more healthful conditions can be obtained. The Bureau of Mines was established by an Act of Congress of May 16, 1910. Since that time the Bureau has been making investigations and compiling and publishing health and safety data relating to mining and to tunneling. If any benefit is to come from an anaylsis of tunneling accidents, it must be the knowledge needed to prevent their repetition. The Bureau of Mines has also had informal discussions with the Department of Labor regarding the possibility of the Bureau's assuming that agency's responsibility for tunnel inspections.

Jan 1, 1997

By Kapila Pathirage, Michael S. Schultz, Gregory Sanders, Ulf G. Gwildis

Adequate understanding of the subsurface conditions along the alignment of a planned tunnel is key for managing project risk. For achieving this understanding, geotechnical borings are conducted during design. Where their spacing cannot reduce the risk of encountering differing site conditions (DSC) in-between borings to an acceptable level, supplemental exploration methodologies or data evaluation approaches may be required to bridge the data gap. This paper compares the exploration design approaches of recent tunnel boring machine (TBM) and microtunnel boring machine (MTBM) projects in the quaternary deposits along the Eastern Seaboard, the glacial geology of the Pacific Northwest, the sedimentary rocks of the South, and metamorphic rocks in western Germany, describing their respective effectiveness of managing DSC risk.

Dec 1, 2022

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open-pit and underground mines of all sizes are regularly collecting point cloud data as laser scanning (LiDAR) and photogrammetry surveying devices have become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely and safely, rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing. This article specifically focuses on digital outcrop modeling and digital terrain engineering. Point clouds. The high-resolution and increasing availability of point cloud technology is rapidly improving open-pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations and typically the reflective intensity and/or the visible three-band color of each point (Fig. 1).LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device.Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles and even in a mobile backpack shown in Fig. 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds,” but this article does not address these due to their higher cost and lower versatility and mobility."

May 1, 2016

By Steve Kral

Competition in the gold mining industry throughout the world has become fierce in recent years. The challenge facing operations personnel is to produce more gold for less money. Likewise, the explorationist's charge is to find more gold in a more cost-efficient manner. That means using new technology to find new gold deposits and expand present ones. More accurate mapping instruments are available to geologists in the search for new deposits. Advanced geophysical and geochemical methods enable explo¬ration teams to review previously mined districts in their search for minable reserves. Four technical sessions on the geology, exploration, and development of gold deposits were part of the program at `world Gold '89,' a Gold Forum on Technology and Practices," held by SME and The Australasian Institute of Mining and Metallurgy in Reno, NV, Nov. 5-8, 1989.

Jan 1, 1990

By Louis M. Perlman

Quantitative methods are, by now, a standard tool of the mining industry, and are commonly used by Research Departments in their evaluation of production methods and schedules, and their associated costs. Indeed, much sophisticated computer work has been devoted to such evaluation of controllable costs and capital requirements. These data are an important input into the project evaluation formula, which is probably the most important single calculation per formed by a mining company, since the result decides whether a particular project is viable. It is instructive to summarize the broad principles of project evaluation, since they are crucial to the remaining sections of this paper. PROJECT EVALUATION The most widely used method of appraising projects is known as Discounted Cash Flow (DCF) method. Two main variants are used; they are known as the 'not present value' (NPV) approach and the 'internal rate of return' (IRR) approach respectively. The difference between the two is that the former takes the firm's interest rate as given and uses this knowledge to calculate the present value of the project; whereas the latter calculates the highest interest rate the project could tolerate and still just breaks even. The technique is more simply discussed in terms of the first method (NPV).

Jan 1, 1972