Search Documents

By Christoph Schulte-Schrepping, Bou-Young Youn, Rolf Breitenbücher

"The main requirements of two-component grouts are a high workability and sufficient stability against sedimentation with a retention time of more than 72 hours, as well as a rapid strength development im-mediately after grouting. Component A usually consists of OPC, water, bentonite, and retarding agent. Component B, a liquid accelerator, is added to Component A during grouting at the end of the shield tail. Current investigations on different compositions of Component A showed a high workability lasting for at least 72 hours. The workability could be extended with increasing amount of the retarding agent to a certain degree. An increase of the bentonite content improved the stability of the mix, but had a negative impact on the flowability respectively the workability of Component A. High compressive strengths could be rather achieved by an adapted mixing ratio of Component A and B than by increasing the amount of the accelerator. Thereby, the interactions and compatibility of the selected constituents play an essential role. INTRODUCTION In mechanized tunneling with segment linings, the annular gap between segment ring and soil must be filled instantaneously with an adequate grouting mortar. The main functions of the annular gap grouting are to stabilize the tunnel lining and to minimize settlements of the ground surface at the same time. Thereby, two contradictory requirements are demanded on annular gap grouts: On the one hand a high workability and sufficient stability against sedimentation, on the other hand a rapid strength develop-ment immediately after grouting. Besides single-component grouts, which achieve the necessary stiffen-ing by dewatering into the surrounding soil, two-component grouts are used, especially in cohesive soils with a very low permeability. Basically, annular gap grouts are almost exclusively defined on empirical basis. Fundamental studies about the constituents and composition of the grout as well as the related achievable properties are still missing so far. Therefore, it is necessary to investigate the material-specific correlations regarding the relevant parameters of annular gap grouts – workability and flowability, stability of the mix as well as strength development – in comprehensive experiments. Based on the knowledge gained from the investigations, it should also be possible, to perform the grouting material according to a real design concept and thus, to ensure an adequate grouting in prac-tice considering the geological and hydro-geological conditions."

Jan 1, 2016

By Sean Warren, JOSEF BOURGEOIS

The potential of rockfall at open-pit mines presents a continuous hazard to mine workers and is typically mitigated by designing catch benches at empirically determined widths. The National Institute for Occupational Safety and Health (NIOSH) is working in conjunction with industry and academia to revisit and update current catch bench guidelines to better match acceptable risk tolerances for modern mining practices. To begin this process, a rockfall testing program was designed to gather empirical runout and bench catchment data at partnering mine sites in the Western United States. This paper presents a detailed description of each component of the rockfall testing program, including scouting and safety plan development, equipment requirements, synthetic rock development for uniform testing across varying bench configurations, local rock collection for testing of mine-specific geology, data acquisition during testing, and data processing. Additionally, this paper describes how the program has been updated over time according to lessons learned during initial rockfall testing.

Feb 1, 2024

By C. Ostrowski, Z. Fajklewicz, K. Jakiel

Results of the application of the micro-gravity method in predicting rock bursts and rock mass deformations are discussed. Research was done in the Daisy black coal mine, Upper Silesia, Poland, during 1979-1980. At that time, microgravity investigations helped increase the safety of coalbed exploitation in progress. During the first stage of exploitation, a mining shock of 107 J energy was predicted in a region where 40 miners worked.

Jan 1, 1987

By P. Gelfi, G. Hill, A. Showell, V. Martins, R. Dunne, R. Jenkins

Carbon attrition losses are not usually a prime consideration for CIP equipment selection and CIP plant design. However, the costs as a result of carbon attrition and associated gold lost with carbon can be high. Recorded carbon losses for Newcrest operating gold plants were shown to vary widely from plant to plant. The Tuckabiana plant recorded an overall loss of only 0.3g carbon /t ore which is very low by industry standards. A comparative carbon management study was undertaken by Newcrest to highlight the reasons for the excellent record of Tuckabiana operation compared to other Newcrest plants. This paper discusses the results of the comparative study and high­lights areas of concern with respect to carbon attrition.

Jan 1, 1995

By John Brett

BHP Australia Coal Pty. Ltd. (BHPAC) manages and, through its parent company BHP, partly owns seven large opencut mines in the Bowen Basin of Central Queensland, Australia. In terms of developments in surface mining in Australia, the operations of BHPAC are as representative as any. The seven mines managed by BHPAC produce a combined total of about 40 Mt/a (44 million stpy) of mostly high quality coking coal. They also produce small but increasing amounts of thermal and PCI coal. Virtually all of the coal produced is sold on the export market. In 1993, Australia exported 133 Mt (146 million st) of coal. Salable production was 172 Mt (189 million st) in New South Wales and Queensland and 180 Mt (198 million st) nationwide. Mining systems Surface coal mines in Queensland can be typified as large, long-strike-length, shallow-dipping and sometimes multi-seam dragline operations. There are exceptions. Blair Athol, for instance, works a 30- to 40-m (100- to 130-ft) seam beneath shallow cover but is still a dragline operation. Moura is truly multi-seam and steeper dipping but also is still a dragline operation. Mines in the Ipswich area are small shovel-truck operations.

Jan 1, 1995

By S. G. Haycocks, M. Karmis, C. Haycocks

Risk assessment is a primary factor in the decision to mine some near surface orebodies, such as limestone, by either surface or underground methods. Identification and quantification of risks demonstrate that environmental concerns are greater for surface operations than underground, and may include such factors as runoff, spoil piles, aesthetics, dust, and large site reclamation. Risk assessment also includes local public feeling towards surface and underground operations while considering the balance between environmental impacts and the economic effects of mining on the local community. A complete understanding of the risks involved permits a comprehensive and accurate comparison between the two mining alternatives.

Jan 1, 1992

By DEVY DYSON, Brian Hart, JOHN LANGHANS, Stamen Dimov, STEVE YOPPS

A recent Nevada Gold Mines research program focused on pressure oxidation pre-treatment of a Carlin-type double refractory ore from the Turquoise Ridge Mine. The research team found that both arsenian pyrite and carbonaceous matter were highly oxidized within an hour at 300 °C using a bench-top autoclave reactor and that the gold recovery from the residues after cyanide/carbon-in-leach approached the technical limit set by the amount of gold encapsulated by silicate minerals. Although the 60-min pre-treatment at 300 °C yields robust performance when treating a whole ore, copper additives can catalyze the oxidation rate of carbonaceous matter and reduce the residence time needed at elevated temperature. Certain gangue minerals are susceptible to dissolution in acidic solutions at 300 °C, and this may cause poor gold recovery. This recovery challenge is mitigated by keeping free acid in the discharge solution below a key threshold.

Jun 21, 2022

By A. Röttger, W. Theisen, J. Küpferle, M. Alber

"Wear of TBM tools significantly affects tunneling advance rates. Wear-prediction models are based (amongst others) on the abrasivity of the present geology, which is determined via laboratory tests. To evaluate the results from such tests in context, this work considers the tribological system TBM tool from a materials technology perspective. In so doing, the microstructures of different application-oriented materials are presented and discussed in terms of their wear behavior and wear resistance. The significant influence of tool materials on the abrasivity of the geology and thus wear prediction models has already be identified. LCPC, Cerchar and nano-scratch experiments have been performed as confirmation. Material-dependent wear mechanisms and their correlation in terms of tunneling have shown that it is mandatory to consider the complete tribological system to estimate the wear of TBM tools. 1 INTRODUCTION Mechanized tunneling is vital to ensure necessary infrastructure development in megacities like Tokyo (Bay Tunnel), Istanbul (Eurasia Tunnel) and Mexico City (Tunnel Emisor Oriente). The use of Tunnel Boring Machines (TBMs) has been established for many years. In contrast to other methods such as boring and blasting or excavation using dredgers, tunneling with TBMs allows simultaneous excavation and removal of both the mineral and tunnel lining by tubbing segments or shotcrete. This makes tunneling more efficient, allowing for faster development of the tunnel in both hard rock and soil [1]. When budgeting such tunneling projects, precise planning and coordination in terms of tunneling technique choice (e.g. EPB or Slurry-shield), the relevant geology, and the associated penetration rates and tool wear are required. In particular, wear to TBM tools has a significant impact on tunneling progress. Due to wear, tools become dulled or lose their functionality because of brittle material behavior, thus reducing penetration rates and therefore tunneling efficiency [1]. As a result, additional tool changes are necessary, leading to higher overall costs due to down times and maintenance costs. Therefore, there is strong interest in a reliable and precise wear prediction model for TBMs. As already mentioned, the geology and associated wear of the tunneling tools define the maintenance times."

Jan 1, 2016

By William Gleason

"Modern society demands much more from the mining industry than just the raw materials it produces. In addition to providing copper, gold, coal and other minerals that make society function, the industry must conduct its operations in a safe and environmentally sustainable manner. This includes the equipment used and the engines that power the machines.In the United States, Tier 4 diesel engine standards that were set by the U.S. Environmental Protection Agency (EPA) are the strictest emissions requirement for off-highway diesel engines. This requirement regulates the amount of particulate matter (PM) and nitrogen oxides (NOx) that can be emitted from an off-highway diesel engine. In Europe, the Euro V standards are driving technology advancement in the sector.The European Euro V standards are required for new equipment manufactured beginning in January 2019. U.S. Tier 4 standards for heavy-duty off-road engines came into effect with model-year 2014 vehicles and equipment. China 6 standards come into effect in July 2020. India’s Bharat Stage VI standards will take full effect in 2020, and the phase-in of BSVIcompliant clean fuels began in April 2018.Caterpillar, Cummins and MTU are three of the leading manufacturers of engines for the mining sector. Each company is working toward creating efficient engines that can function in the often harsh environments found at openpit and underground mines around the world. In short, society is placing demands that are challenging engine manufacturers to deliver a product that can do more work while consuming less fuel and emitting fewer emissions.Technologies range from selective catalytic reduction (SCR) and diesel particulate filters (DPFs) to other engine strategies and emissions control technologies, which deliver near-zero black carbon and nitrogen oxide emissions, and lower greenhouse gas emissions. Caterpillar’s investmentCaterpillar, the world’s largest producer of mining equipment and mining engines, has been at the forefront of the changing demands placed on the industry and has remained on the cutting edge of engine development over the years, thanks to its investments in the sector.“Caterpillar made the choice to fund major engine and machine development work — even during a deep trough in the mining industry — so that Cat machines would meet Tier 4/EU Stage 5 mandated compliance dates of Jan. 1, 2018 / Jan. 1, 2019, respectively. For Caterpillar, these efforts enabled our mining trucks to provide improved engine component life to help our customers’ total cost of ownership (TCO) and produce a neutral TCO compared to our Tier 2 products,” said Jeff Castleman, new product introduction manager, large mining trucks for Caterpillar."

Aug 1, 2019

By Sheldon P. Wimpfen

Sand and gravel has been, and will continue to be, our principal construction material. Most of us are familiar with the patterns of past growth. Today we will examine the present status of this vital industry. We shall also attempt to look into the future to see where it is going and to evaluate the constraints that are being imposed. Natural aggregates are among the lowest in value of all bulk industrial minerals. From the processing point of view, sand and gravel production is relatively simple since the products are sized materials obtained from a deposit of satisfactory physical soundness. They can be used either loose or bound to provide bulk, strength, or protection. One of the main uses of coarse aggregate is in concrete as a filling material. As a general rule, the coarse aggregate constitutes about three-quarters of the volume of concrete. The other main use for aggregate is as a roadstone or roadbase to provide protective and stabilizing bulk beneath the road surface. Also it is used in a mixture with petroleum products as the wearing course on top. The sand and gravel industry is geographically widespread. In general, the output of operations is directly proportional to the amount of construction in any area. A wide variety of other aggregates compete with sand and gravel, including crushed stone, blast-furnace slag, clinker, and artificial and natural lightweight materials.

Jan 1, 1972

By S. K. Sharma, D. A. Stanley

The US Bureau of Mines is investigating the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters, namely, shear rate, polymer dosage, and polymer concentration, on floc growth and to determine the applicability of a model for predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. The results showed that the model reproduces the experimental data with only reasonable accuracy and that it was relatively insensitive to the parameters. Results of the flocculation study showed that increases in the polymer dosage had a greater effect on the time required to reach the maximum floc size than on the floc size itself: It was also determined that, given all the above parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on floc growth.

Jan 1, 1995

By Carrie Smith

The Society for Mining, Metallurgy & Exploration’s annual conference and expo, MINEXCHANGE 2026, will take place Feb. 22–25, 2026, at the Salt Palace Convention Center in Salt Lake City, UT. The event will foster a hub for innovation, technical exchange and policy discussion for the global mining industry. Over four days, attendees will take part in short courses, technical sessions, field trips and networking events that highlight the advancement of the mining industry. The conference’s keynote session, titled “Regaining America’s Mineral Dominance,” will start at 8:30 a.m. on Feb. 23 in the Grand Ballroom E–J. The speaker will address the sweeping policy actions now shaping the nation’s mineral future, following a series of executive orders issued by the Trump administration designed to bolster domestic mineral production and energy security. These directives, including Immediate Measures to Increase Domestic Mineral Production (EO 14241) and Establishing the National Energy Dominance Council (EO 14213), have set in motion a coordinated effort across the Departments of Interior, Energy, Defense and Commerce to enhance the United States’ position as a global leader in critical minerals. The invited speakers include Utah Governor Spencer J. Cox and Nate Foster, managing director of Rio Tinto Kennecott, who will examine how policy and industry are converging to meet surging demand for minerals essential to modern technology. Governor Cox is expected to highlight Utah’s long-standing role in American mining, from the early development of Kennecott Copper to its current position as a producer of 40 of the nation’s 50 identified critical minerals. Foster, meanwhile, will offer insights into Rio Tinto’s extensive operations in Utah, including the Kennecott Copper Mine — one of only two operating copper smelters in the United States — and the company’s ongoing efforts to build more resilient, sustainable supply chains. Rio Tinto’s work in critical mineral production, from copper and tellurium in Utah to new operations in Arizona, has made it a fundamental figure in the U.S. mineral economy. Projects such as the Resolution Copper development and the revival of Gunnison Copper using Rio Tinto’s innovative Nuton technology illustrate how private-sector leadership is driving sustainability in domestic mining. These advancements come at a critical moment for the industry, as copper prices remain near historic highs. The keynote session will emphasize that meeting future mineral demand will require a concerted effort between government, industry and technology partners to secure responsible, domestic production. Immediately following the keynote, the Robert E. Murray Innovation Award Lecture will start at 10 a.m. as part of the same session. Lucy England, managing director at FLSmidth, will present on “Sustainable Copper Mining Flowsheets and the MissionZero Mine.” England, who has spent more than 25 years in mineral processing and innovation, will discuss how FLSmidth’s MissionZero initiative aims to develop the world’s most efficient

Feb 1, 2026

By D. Dunbar

The flooding of open pits is now receiving considerable attention from the mining industry as an option that may minimize environmental impacts, particularly when anoxia in pit-lake deep waters can effectively eliminate oxidation of pit-wall sulfides. This paper describes a state-of-the-art, coupled physical-geochemical pit-lake model. The model is used to verify that a controlled, two-stage infilling of the open pit at the Kori Kollo gold mine, southeast of La Paz, Bolivia, would result in a cost-effective, environmentally responsible closure strategy. By filling the pit initially with highly saline surface waters and naturally saline deep groundwater and then capping with fresh river water, a very stable and strongly stratified pit lake will be developed. In addition, the stratification will result in the isolation of metal-rich saline bottom waters from surface waters of good quality. Results of this model provide defensible predictions of the physical stability and evolution of water quality in the Kori Kollo pit lake over time. The model results indicate that anoxic conditions will develop below the fresh-saline water boundary within one to two years, followed by the rapid onset of sulfate-reducing conditions in the bottom waters. Hydrogen sulfide produced by sulfate reduction will readily react with dissolved metals to form highly insoluble metal sulfides. The process results in the gradual removal of metals from the water column and the concomitant improvement of water quality over time. A notable benefit of this strategy is that it can be fully integrated with other mine site closure options as well as future environmental-management strategies. The proposed plan allows for the safe isolation of saline waters, the potential for passive treatment in anoxic bottom waters of ARD seepage from other mine site operations, should they arise, and a repository for future reactive wastes that could be effectively isolated in a physically and chemically stable environment.

Jan 1, 2003

By Merrill P. Allen

The Vernal phosphate rock concentrator is located in the Uinta Mountains near Vernal, Utah. Ore is sedimentary rock from the Phosphoria Formation. Truck and shovel mining is done at a rate of 11,500 TPD. Run of mine ore is crushed and then milled through a SAG mill and ball mill to minus 16 mesh. Milled ore is deslimed using cyclones and hydrosizers. Sands are conditioned with fatty acid, petroleum sulfonate, diesel fuel and frother prior to primary rougher and cleaner flotation. Primary flotation tailing is milled to 95% minus 48 mesh, deslimed in cyclones, conditioned using reagents previously described, and then processed through rougher and cleaner scavenger flotation. Product of scavenger cleaner concentrate is upgraded by reverse flotation of dolomite. Flotation concentrates are combined and dewatered, pulp being milled to 99.5% minus 65 mesh and then thickened to 65% solids. Product is pumped from storage through a 10 inch, 94 mile pipeline to a conversion plant at Rock Springs, Wyoming. Mill tailing is stored behind an earthen dam, water from the settled tailing being reclaimed for mill use.

Jan 1, 1993

By Mucella Ersoy, Nese Celebi

Management Information System (MIS), is a system using formalised procedures to provide management with appropriate information to make timely and effective decisions. Before developing MIS, first functions of the organisation should be defined and grouped into subsystems. After determining the information required and produced by each system and interaction between subsystems, the related data resources should be structured into a series of databases and files. In this study, the MIS developed for Soma Open Pit Mines, Turkey is described in this respect. First, analyses of the existing system including user requirements and scope of the system are given. Then the designed information system, its subsystems, interaction between subsystems and system structure are presented in detail.

Jan 1, 2002

By Michael Michaylov, Elena Vlasseva

On the basis of well known and widely used in mine practice retreat longwall mining system, physical and mathematical models of air leakage dynamics have been created. Flow is assumed viscous-inertial and considering natural anisotropy of porous media of a gob area. As a result of modeling pressure and leakage distribution and velocity field can be defined. Thus the model presented in this paper can be used as aerodynamical prediction of gob area characteristics.

Jan 1, 1995

By A. F. Barsotti

Apart from jewelry, holistic apparel, and special collections of color and sometimes rare crystal specimens, the average layperson has little or no appreciation of the omnipresence of minerals or mineral derived products in the home. From concrete in the driveway to aspirins in the medicine cabinet, minerals, especially industrial minerals, play a major role in day to day living. For a better appreciation of this let's look into the a day of the life of a fellow named John, and see how much we depend on industrial minerals. The sounds of soft violins nudged John from his sleep. The melodic sounds of Beethoven's Pastoral coming from his radio alarm clock brought him out of his dreams. He reached for the reading light switch, then checked his watch--6:30 a.m., and another day of work. As he got up, the darkness outside reminding him of winter coincided with the soft voice of the all night disk jockey forecasting the fall of four inches of snow. Warm beads of water beating on his face removed all remnants of sleep and, like a stimulant, the morning shower brought thoughts of yesterday and plans for a new day. These carried over as he looked himself in the mirror while shaving and brushing his teeth.

Jan 1, 1993

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By Y. F. Vasyuchkov

In general a term "unconventional mining or "non-traditional mining technology" getting more and more familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in Figure I:

Jan 1, 1997

By T. A. P. Sankar, S. Gundiah, Pradip, R. A. Kulkarni

Two modified polyacrylamide flocculants, namely polyacrylamide with glycolic acid functionality (PAMG), and a copolymer of acrylamide with N-acryloyl-[T]- aminobutyric acid (HPVP), were synthesized, characterised and evaluated for selective separation in apatite/quartz and apatite/dolomite/calcite systems, respectively. PAMG flocculant was found selective in the separation of tricalcium phosphate (TCP) from its mixtures with quartz at acidic to neutral pH range. The selectivity deteriorated at alkaline pH. In contrast, polyacrylic acid (PAA) flocculant was found most effective only in the alkaline pH range. HPVP flocculant (even though flocculating all three minerals namely apatite, dolomite and calcite) was observed to be quite selective for the separation of calcite from apatite-dolomite minerals in single mineral tests in the presence of sodium hexametaphosphate dispersant at neutral pH. There was, however, no selectivity observed during tests on synthetic mixtures. This loss in selectivity is attributed to the phenomenon of hetero-flocculation, as reported earlier, for separation in an apatite-dolomite system with polyethylene oxide.

Jan 1, 1993