Search Documents

By A. J. Vietti

"Drought conditions and the possible lack of sufficient raw water supply are a constant reminder to the Southern African diamond miner of the need to minimize raw (new) water input while maintaining or expanding mine throughput.Since water input volume is directly related to water output (loss) volume, mainly to the tailings, it is obviously beneficial to dewater the tailings as much as possible. However, this may not always be as easily achieved as first thought. Owing to the unique mineralogy of each kimberlite deposit and the unique chemical profile of each raw water source, dewatering of the slurry is not a standard process that can be applied equally across the entire diamond industry.This paper presents a first-step strategy that kimberlite diamond mine operators should consider and apply to meet and exceed their watersaving targets. Introduction A common metric for measuring water use efficiency in a metallurgical plant is the amount of raw water used per ton of head feed treated (m3/t). The metric includes all water recycled from the dewatering process and from the tailings storage facility (TSF), and the only inputs are tons of ROM ore and cubic metres of raw water make-up to replace water lost to evaporation, seepage, and lock-up at the TSF (Figure 1).The volume of new raw water available to the process is not unlimited and a maximum monthly allowance is typically set during the mine permitting process. Consequently, if the volume of water lost exceeds the volume of new water available or alternatively, in times of drought where the allowable volume is unavailable, the plant has no other option but to reduce throughput.However, if the plant operator is able reduce the volume of water lost to the TSF, the plant will have additional capacity to either increase tonnage throughput or sustain nameplate capacity during periods of severe drought. The obvious conclusion, therefore, is to reduce the volume of water lost to the tailings by improving the efficiency of the dewatering process (typically gravity thickening) simply by increasing the density of the tailings being discharged. In practice, however, the unique mineralogy of each kimberlite deposit and the chemical profile of the raw water source used imply that at some mine sites, solid/liquid separation (or settling) of tailings slurries at the dewatering process is more easily achieved than at others. In these cases, simple practical steps such as firstly improving the flocculant reagent make-up and dosing control, and secondly focusing on thickener discharge control, are the only requirements for enhancing water recovery at the dewatering circuit. At other mine sites however, solid/liquid separation of the tailings may not be achieved at all, in which case efforts to increase water recovery by improving reagent dosage and thickener control would be fruitless unless the colloidal properties of the thickener feed slurry are modified."

Feb 1, 2019

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By Y. Fu, C. Aldrich

This study investigates the use of dense convolutional neural networks to estimate bubble size distributions in flotation froths. 20 videographically captured images of froths from an industrial platinum flotation plant in South Africa were labelled semantically with an image annotation tool, LabelMe (https://github.com/wkentaro/labelme). As a result, pixels in the images could be categorized into three classes, namely ‘bubbles’ (class 0), ‘bubble boundaries’ (class 1) and ‘background’ (class 2). A U-net architecture with a ResNet34 backbone was trained to segment the images via classification of the pixels in the images. 5 of the 20 images were used to validate the performance of the neural network. Explicit inclusion of the bubble boundaries as a class proved to be significantly more effective than training the network with two classes only (i.e. bubbles and background). However, the thickness of the boundary layer regions were critical. If too thin, it was difficult to distinguish between some contiguous bubbles and if too thick, some fine bubbles may not be identified. The results were promising, although there is still significant scope for improvement, among other by making use of more images for training and validation. Keywords: Flotation Froths, Convolutional Neural Networks, Deep Learning, Bubble size Analysis

Jan 1, 2020

By N. V. Nemchinova, A. A. Kozlov, A. V. Epiforov

The gold dissolution in sulfuric acid media during industrial oxidative leaching test of sulfide gold-copper flotation concentrates has been achieved. The reason for this was using technological water containing thiocyanates and cyanides, which can dissolve gold under these conditions. The carbon in column (CIC) process for gold recovery from these solutions was proposed. However, significant amounts of copper and iron were adsorbed onto the carbon during CIC technology industrial tests. This resulted in a decrease of the gold content in the loaded carbon up to 0.5 kg/t. Further development of the technology was conducted by optimisation of gold and impurities stripping and implementation of carbon reactivation. It was shown, that the copper extraction from the loaded carbon during cyanide treatment was about 95%. The copper content in the stripped carbon after cyanide treatment was 1.76 kg/t. The gold recovery during high-pressure elution by caustic solution was 98%. The hydrochloric acidic treatment with thermal pre-treatment (reactivation) for removing iron and calcium from gold-free carbon was proposed. In this case, the iron and calcium extractions from carbon were 40-45 and 50-55% respectively. These tests showed that for carbon recycling the sequence operations of ‘cyanide treatment, gold elution, thermal pre-treatment, hydrochloric acidic treatment’ can be used. Keywords: Thiocyanate leaching, recovery of gold, carbon adsorption, gold elution, copper stripping, thermal reactivation of carbon, activated carbon, carbon-in-column

Jan 1, 2020

By J. P. Gous, M. Tangstad, J. D. Steenkamp

In April of 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. One of the areas excavated systematically was the furnace taphole. The aim was to obtain a refractory wear profile of the tap-hole area, together with affected hearth and sidewall refractory. Subsequently, thermodynamic modelling was applied to quantify the potential for chemical reaction between refractory and slag and refractory and metal in the tap-hole area.

Jan 1, 2014

By F. T. Cawood, M. N. M. Cudjoe

The ability to conduct real-time material tracking in mines has been a long-standing challenge. Technological innovations such as radio frequency identification technology (RFID) have over the years contributed to the effective tracking of material flow and reporting of metal content. This paper outlines the laboratory procedures and results from testing the suitability of microdot technology as a viable technique for real-time material tracking in mining. The paper clarifies the reasons for conducting the test and presents the material safety data sheet (MSDS) from a South African and Canadian perspective. Microdots from three aerosol systems were immersed in water, heated to 100°C, and crushed into coarse and fine material. These tests were used to ascertain if the technology could withstand mining conditions. A strength, weakness, opportunity, and threat (SWOT) analysis was used to evaluate and compare microdot technology with RFID. It was shown that microdot technology has some potential to track ore parcels because data integrity was retained after exposure to post-blast mining conditions. However, more improvement is required to digitally detect microdots before the technology can be implemented at scale in the mining industry.

Apr 2, 2022

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran, J. Zoric

A methodology for building pragmatic physics-based models is here adapted to predict the erosion of ladle linings in the steel industry, in order to support operators when deciding whether the lining can be used safely for another heat. A defective lining may allow 140 t of molten steel to spill, with disastrous consequences for workers and plant. The adopted work flow for the development, challenges faced, and some model results are presented. One key learning outcome is that model development should allow time for maturing the process understanding, as well as for many iterations by ‘questions-responses and actions’ at various stages in the model development. Good interaction between the development team and industry case owner is an important success factor. Combining or extending the model with the use of machine learning and cognition-related methods, such as knowledge graphs and self-adaptive algorithms, is discussed.

Apr 16, 2024

By G. R. Baiden

Introduction The introduction of teleremote systems to underground mining can provide a significant improvement in the performance of a mine when compared with conventional mining techniques. This paper presents the concepts of teleremote mining in a case study showing how the systems work and the competitive advantage autonomation of mining techniques will provide for underground metal mining operations into the future. This paper is divided into two sections: the Mining Automation Program and What is next? On January 1st 1996 Inco Limited, Tamrock Oy, DYNO Explosives Group and CANMET formed a consortium for the development of teleremote mining equipment called the ‘Mining Automation Program’ or MAP. This program included a five-year research and development agreement that combines the talents of the above organizations to create mining equipment and systems for autonomating mining. The projects are based on the communication system currently sold and marketed by Automated Mining Systems Limited. The main components of the program investigated the development of a positioning and navigation module, autonomated systems using teleremote techniques for development and stoping, and software systems to support the use of this equipment. The program included the establishment of a test mine, at Inco’s 175 Orebody near Copper Cliff North Mine. This facility was unique allowing collaboration of companies and research organizations inthe design and testing of techniques and equipment used to apply autonomation to mining. Since the inception of the project other research alliances have been added to enhance the program. These include the application of ground support (Meyco/ Master Builders), muck pile recognition, the broadening of telecommunications links (PRECARN Associates Inc.-MALTA project) and the collection and processing of drilling core through the automated diamond drilling project (J.K.S. Boyles). MAP began as an idea a number of years ago with the fundamental question ‘Can an ore-body be profitably mined through autonomation?’ The concept was to design mining equipment and systems that would allow the teleremote operation of a mine. Automation was only one componentof this much larger teleremote mining issue. To start with, it was essential to prove or disprove the feasibility of this concept. The fundamental requirements are: • Telecommunications • Positioning • Navigation • Equipment • Software • Electronics • Mining Engineering • Organization. Each of these had to be considered. Technically, the feasibility of the project hinged on the successful development of a high capacity communication network, an accurate underground positioning system, a navigation system and finally the electronics and software that could integrate these. Mining equipment that could perform all the mining functions was the next requirement, along with explosive supplies that could be delivered to the holes teleremotely. Whatever the systems developed, they must be able to work in both bulk and selective mining situations and in varying conditions within a mine. Finally, the organizational issues of a change from our current method of operation to teleremote mining had to be understood. After five years of research and development the answer to the question ‘Can an orebody be profitably mined using autonomation techniques?’ is YES! There are still hurdles to overcome, however, the basic premise has been proven. The development and production of underground tunnels and stopes has been done. There have been interesting outcomes in terms of reduced effort to accomplish mining and the total time to mine. Definitions •Automationis the process by which a machine or system is run continuously including the ability for the system to self-correct. •Autonomationis the same as automation except that the process does not self-correct. •Teleremote operation is the operation of mining equipment over a network from any location out of line-of-sight of the machine. •Equipment Automationis the addition of technology to a machine that allows for unmanned operation of a machine and thus enhances the productivity of the operator. For example, a guidance system that allows a load-haul-dump to drive by itself, thus freeing the operator for other tasks. •Teleremote mining describes a mine process that combines the use of teleremote operation (potentially with some automation), positioning and process engineering, monitoring and control. •Tamrock DataSoloTMis a computerized drilling rig as shown in Figure 1. •Tamrock DataMini™ is a computerized development drill rig used for drifting and construction tunneling as shown in Figure 2.•Tamrock Toro 450™ is a LHD (Figure 3).

Sep 1, 2001

By P. de A. Barbosa, M. G. Bergerman, E. da Fonseca

Located in the state of Pará, Brazil, the Sossego copper and gold mine consists of a heterogeneous geological deposit. Its complexity derives from the hydrothermal alteration, the ore-forming event, which modified the host rocks, such as granite, and metamorphosed volcanic rocks into several mineral assemblages. Different mineral assemblages have led to differences in abrasiveness. A few Bond abrasion tests conducted during the mine feasibility study did not provide a robust abrasiveness database, thus the variation of physical properties for some mineralisation host rocks was not possible. Although several test methods may be used to determine ore abrasiveness, the Bond method is the one most commonly used in the mining industry. Despite being simple to carry out, this test method has certain limitations as to particle size and the amount of ore sample required, which often makes it difficult or even impossible to apply in the early stages of a project and in geometallurgical studies. The Laboratoire Central des Ponts et Chaussées (LCPC) test may provide an alternative, as it requires a smaller amount of fine-grained material. This study aimed to provide data on wear properties of various ore types from Sossego mine using the LCPC method. It included validation for 40 different ore samples using the Bond test as a benchmark. The results showed good correlation, indicating it may be possible to use the LCPC test as an alternative to the Bond abrasion test. A high abrasiveness index was found for acid metavolcanic rock, confirming the results observed in Sossego mill’s operating database, pointing to a mineralogical drive to amorphous quartz. Keywords: Abrasiveness, geometallurgy, copper ore, Bond abrasion test, LCPC

Jan 1, 2020

By C. Bergmann, V. Ross

The concept of underground ore processing, in which valuable ore and waste are separated at a coarse particle size to improve the economics of operations and minimise the environmental impact, seems attractive from a sustainability perspective. Perceived benefits of such an operation include energy and cost savings due to a reduced hoisting load, a reduced footprint of surface operations, and using material for backfill that has not been contaminated by process chemicals. Progress in the South African mining industry in this area has however been below expectation, and opportunities for underground processing in deep, narrow reef operations were therefore explored by an Excel-based simulation with sensor-based sorting (SBS) as concentration technology. Various PGM mining scenarios incorporating factors such as the mining rate, depth of operation, and effects of dilution and particle size on the metallurgical efficiency, were compared. Whilst these initial results can be regarded as indicative only, they have shown that the economics of such an operation are driven by selective mining at significantly higher rates than achievable with conventional methods. Also, the cost of preparing, conveying and placing rock backfill will need to be lower than that of hoisting waste and depositing it on a surface dump. Another aspect to be addressed is whether ore sorting machines would be able to operate under harsh conditions underground and what provision would need to be made to ensure their efficient operation. Further investigations should focus on refining costs, incorporating environmental considerations in the modelling of economics and sustainability, and compare greenfields with brownfield scenarios. Keywords: Ore sorting, hoisting, backfill, mining rate, economics simulation

Jan 1, 2020

By M. Ye. Scheglov, G. I. Voiloshnikov, S. M. Ryakhovsky, V. E. Dementyev, V. N. Alekseev, N. S. Voiloshnikova

Irgiredmet has substantial experience on RIP and RIL technology for gold recovery, having started development of ion exchange technology in 1964. Irgiredmet specialists were involved in the majority of RIL and RIP projects in the former Soviet Union and Russia, and took part in commissioning of practically all plants using ion exchange technology. Laboratory and pilot plant tests were conducted to develop process design criteria for designing 15 RIP plants of the former USSR using bifunctional macroporous anionite AM-2B or its analogs. This paper is devoted to the laboratory, pilot plant testing and introduction of RIP technology conducted in cooperation with GC Pertopavlovsk. Medium base resin PuroLite S992 (PuroGold) was used as adsorbent. Some adsorption regularities and the affinity of resin to metal cyanide complexes were studied. Laboratory batch and continuous pilot tests on resin-in-pulp process were held for oxidised ores from Pioneer, Albyn and Malomyr mines (Amur region, Russia) owned by the Petropavlovsk company. A simplified flowsheet for gold elution and resin regeneration was developed. Alkaline cyanide solution was used as gold eluent and gold was recovered from eluates by electrowinning. Process design criteria were developed on the basis of the testwork results, and the plants were designed and constructed by GC Petropavlovsk. The RIP plant at Pioneer was commissioned in May 2008, at Malomyr in August 2010, and at Albyn deposit in December 2011. These plants are currently in operation at design performance at throughputs from 3 to 6.5 Mt/year. The primary gold ores of Pioneer and Malomyr deposits are refractory to cyanidation; Irgiredmet also completed continuous testwork on RIP technology using medium-base resin for pressure oxidation (POX) residues derived from their flotation concentrates. In 2019 a hydrometallurgical plant for the treatment of refractory gold concentrate after POX was commissioned at Pokrovsky mine (Amur region). Keywords: Gold ores, cyanidation, RIP, RIL –processes, ion exchange resin, medium base resin, adsorption, elution, electrowinning

Jan 1, 2020

By L. A. Balzan, M. Kalicinski, F. Nieuwenhuys

GEOSCANs on belt analysers have been widely utilised in iron ore for nearly two decades. Since the first installations in 2003, the availability of accurate and reliable grade data has become standardised across iron ore mines in the Northern Cape, where various streams are monitored continuously to ensure the optimal functioning of plants. Assmang Khumani has been at the forefront of technology adoption and has implemented 19 GEOSCANs at various locations throughout the plant, monitoring run-of-mine, stockyard feed, beneficiation plant feeds, and products. Over the years, collaborative advances in the technology have allowed for numerous benefits and gains to be made. In recent times, there has been a concerted effort on the development of analysis for phosphorus in the material flows, and based on Scantech's experience in the phosphate industry, this element has now been calibrated to achieve statistically acceptable and repeatable accuracies for real time analysis of this element on many of Khumani's GEOSCAN analysers. This paper provides an overview of GEOSCAN use at Khumani, while focusing on the development of phosphorus analysis. A case study of analysis results is presented for a range of analysers that have been calibrated for this element, as well as a discussion on the benefits obtained as a result of this analysis. Keywords: Online analysis, real-time, process control

Jan 1, 2020

By N. Naudé, J. de Villiers, C. P. Bergmann

It is proposed that the physical and chemical composition of individual mineral particles are an appropriate basis from which to model the performance of minerals processing equipment. Such a particle-based approach enables modelling across disciplines such as comminution, classification and flotation and automatically generates the traditional mass and chemistry balances. The general approach followed is to generate full grade-recovery curves for a separator by sampling product and tailings at varying mass yields. AutoSEM characterisation of each sample provides particle data that is used to reconcile mineral deportment and liberation to the measured size and assay data. In this way, partition surfaces can be generated and modelled. In this paper, an empirical model for the performance of a gravity spiral concentrator treating fine chromite ore is proposed. The model is based on the combination of two partition surfaces and is able to accommodate both forward and reverse gravity concentration effects per size fraction. The results show that this approach is well suited to represent spiral performance for the cases evaluated. The effect of two feed particle size distributions on the performance of the Multotec SC21 and SC25 spirals is demonstrated. Simulations are run in an Excel environment, linked to Python-enabled routines for enhanced data management and calculation speed. Keywords: Spiral concentrator, gravity separation, particle-based modelling

Jan 1, 2020

By R. Rubin, P. A. Laxen, G. S. M. Becker

An account is given of developments in the use of activated carbon for the recovery of gold from cyanide solutions. The carbon-In-pulp process employed at the Homestake Mine is described, and its various applications in South Africa and their effectiveness are discussed. Probable future work on the carbon-in-pulp process and other possible applications of carbon for the recovery of gold are outlined.

Jan 1, 1979

By P. A. Corbeil, C. Swart, F. Miller, V. Falmagne

Automation technologies are increasingly adopted in different mines worldwide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHD’s at Noranda’s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHD’s and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda’s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Sep 1, 2001

By G. J. Krige

The extent of ground movements and stress concentrations in the vicinity of the reef in the deep mine-shafts used in the South 4frican gold-mining industry have led to the requirement that special tower structures be developed to span the reef intersection zone in several new shafts. So that structural engineers are able to design these towers, it is necessary to model the dynamic behavior of conveyances traversing them in some way, to provide a means to determine the magnitude of the forces generated. This paper describes the development of two such procedures. The first is a numerical method, utilizing a step by- step integration technique to track the motion of a conveyance through a tower. This technique has been implemented in a computer program, and some results are given.

Jan 1, 1995

By J. M. Czaplicki

The problems connected with deep mine hoisting and the increasing complexity of this process can be analysed through the application of such mathematical tools as stochastic modelling to study the effectiveness, reliability or safety of hoist methods. To relate these theoretical investigations to real practice, knowledge about components, their stochastic nature and stochastic order of appearance is necessary. This paper presents results obtained during the ten-year (1976-85) period of research undertaken in the Polish mining industry by the Mining Mechanisation Institute of the Silesian Technical University, Gliwice, Poland.

Jan 1, 1987

By M. J. Kanda, T. R. Stacey

Thin spray-on liners (TSLs) have been used as sealants and rock support in tunnels for over 25 years. Laboratory tests have indicated satisfactory properties that can provide adequate strength, adhesion, toughness, and elasticity as part of rock support systems in mining excavations. These characteristics are, however, not always demonstrated in practice, when mine environmental conditions do not correspond with laboratory environmental conditions. The shortcomings of TSLs experienced in the mining industry have raised concerns, resulting in scepticism from some operators regarding their utilization. The research described in this paper aims to investigate TSL performance in environmental conditions similar to those experienced in mines. Brazilian indirect tensile (BIT) specimens were prepared from precast shotcrete and coated with TSLs. The specimens were then exposed to different environmental conditions for up to 112 days before BIT testing under various conditions: laboratory room temperature and humidity; saturated room temperature; and combined saturated and high temperature (50°C). Additional uncoated shotcrete and TSL BIT specimens were prepared for comparison purposes. The results of the BIT tests showed that environmental conditions have a significant influence on the tensile strength enhancement of shotcrete by TSLs. Water-based TSLs are most likely to be suitable for high humidity environments, although their performance decreases at higher temperatures. Numerical modelling of TSL-coated BIT samples confirms the potential limitations of designing TSL support based only on laboratory testing carried out under room conditions.

Jul 1, 2021

By M. Mathey

The application of the Monte Carlo technique to production planning and everyday economic decisionmaking in mine production management is demonstrated. The logic is detailed using an example of underground production with continuous miners (CMs) and truck haulage. It is argued that availability of equipment and personnel are the predominant variables influencing mine output and productivity and that those availabilities may be well represented by binomial probability distributions. The probabilistic model is implemented in a standard Excel® spreadsheet with Palisade’s @Risk add-on to facilitate simulations. Starting from model calibration against data obtained from a mine’s annual reports, some general interdependencies of availability, utilization, productivity, and costs of production processes are outlined. Finally, several possible options and their consequences as regards production improvements are explored.

Dec 13, 2022

By А. А. Vasiliev, Y. G. Seredkin, А. V. Aksenov, А. Y. Senchenko

Refractory gold-containing concentrates usually contain gold enclosed in sulphides as well as in rock-forming minerals. Another difficulty is that gold often occurs as very fine inclusions of several micrometres, and even smaller than 1 micrometre, or can be part of the mineral composition at the structure level. Processing of such concentrates is a challenge. Ultrafine grinding and further oxidation are applied for gold liberation. The paper deals with the results from the study of gold deportment using Qemscan, and atmospheric oxidation testwork involving Albion Process™ on a gold-containing concentrate with a high content of refractory gold in sulphides and gangue minerals. Albion process testing was performed at Institute TOMS with the participation of Glencore Technology Pty Ltd (Australia). Additionally, conventional cyanidation testwork was carried out for the concentrate processing. As an alternative technology of gold liberation, oxidising roasting with arsenic stabilisation was used. The results from the study make it possible to assess the efficiency of the above-mentioned methods of gold liberation, and applicability of Albion technology to recover gold from the refractory concentrate. Key words: Gold, refractory concentrate, Albion Process, atmospheric oxidation, oxidising roasting, leaching

Jan 1, 2020