Search Documents

Advances were made during 19b5 in many phases of a broad program designed to increase efficiency in the mining, preparation, and utilization of coal. Also recorded were achievements in activities devoted to mine health and safety, coal resources, and mine explosives. Featured in this report is a review of progress in environmental studies relating to coal mining and utilization. Environmental projects comprise a comprehensive program to facilitate mine reclamation and reduce air and water pollution associated with extraction and use of coal. Publications cited throughout this report present results of the coal program in greater detail. Organizations, institutions, and companies contributing to the program are listed in appendix A. Centers and laboratories conducting the coal research and related investigations appear in appendix B.

Jan 1, 1966

Continuously monitor air-borne radon daughters that are a hazard to underground miners. Approach A beta detector continuously counts beta activity collected on a filter paper to allow calculation of exposure in working level units. How It Works At each Site a constant flow pump draws mine air through a fiberglass filter located in front of a beta detector (pancake type Geiger Mueller tube), Radioactive particles (products of the radon 222 gas emanating from the mine walls) collect on the filter and decay, releasing alpha and beta particles as well as gamma rays. A portion of the beta particles penetrate the Geiger tube window and create electrical pulses in the tube. These pulses are then amplified and sent by a coaxial type or shielded electrical cable to a central monitor located some distance from a working level detector. At the central monitor incoming Signals are amplified and fed into two channels, (See the block

Jan 1, 1979

Enhance coal mine worker safety and productivity by developing a means to control and predict coal mine mountain bumps. Approach The Bureau of Mines has been engaged in extensive research to understand coal mine mountain bumps and their effect on underground coal mining in the United States. Information was collected on the geologic conditions, mining techniques, and engineering parameters at five mountain-bump-prone mines. Although research has not yet evolved to the point where mountain bumps can be effectively predicted or controlled, such studies are invaluable for providing clues that can lead to the development of mountain bump mitigation technology. Case Study Results and Recommendations Mountain bumps in coal mines are explosions of the coalbed that violently release the strain energy stored within it into openings created by mining. Such an event is not only dangerous to mine workers, but can cause substantial amounts of damage to mine equipment, resulting in productivity loss and downtime. In a coal mine, the occurrence may cause coal to be expelled violently from the coal face or coal pillars or cause the mine floor to heave suddenly. Coal bumps are usually accompanied by a very loud noise and tremors or vibrations. Such ground failure:; usually occur in the vicinity of an active gob line in an active retreating room-and-pillar panel, or at or near the face in an advancing or retreating longwall mining panel.

Jan 1, 1989

By Z. Zhiqun, V. A. Marple, B. Y. H. Liu

"IntroductionIt is commonly understood that aerosol particles may be injurious to human health if they are of a size that enables them to enter the respiratory tract. Coal Workers' Pneumoconiosis (CWP) is one disease known to be caused by coal mining related particles.The location in the respiratory tract where the particles are deposited is primarily a function of the equivalent aerodynamic diameter (EAD) of the particle. The equivalent aerodynamic diameter is the diameter of a spherical particle with a density of 1.0 gm/cm3 with the same falling speed as the particle in question. For a spherical particle the calculation is rather simple in that the equivalent aerodynamic diameter is simply the diameter of the particle in question multiplied by the square root of the density of the particle. For irregularly shaped particles, such as coal particles, there is no simple way to make the EAD calculation. For example, Figure 1 is only one of an infinite variety of particle shapes that can be found in practice and the aerodynamic size of this particle and, therefore, its deposition location in the respiratory tract would be nearly impos-sible to estimate accurately.The normal method for determining the aerodynamic diameter of particles has been to experimentally measure the size of the particles in a settling chamber or with an inertial classifier such as an impactor, cyclone or a centrifuge, since inertial classifiers have the property of classifying the particles according to their aerodynamic diameters."") However, these devices can only give limited information on the EAD of a single particle with a specific shape. Impactors and cyclones, for example, collect particles in size ranges and not at a specific size, so the determination of the EAD of a specific particle is not possible. A centrifuge, on the other hand, can measure the EAD of a specific particle but the equipment is costly and procedure laborious, and it may not be possible to disperse a particle of a specific shape into the centrifuge. The centrifuge can be used to determine the EAD of clusters of spheres in various arrays, but introducing particles of a specific irregular shape may not be feasible. Furthermore, the EAD is a function of the orientation of an irregularly shaped particle and the orientation of a particle in an inertial classifier is unknown. The orientation may also vary as the particle passes through the classifier.Because of the difficulty in determining the EAD of an irregularly shaped particle, we have undertaken a program to apply theoretical numerical methods to calculate the EAD of any shape particle. In our laboratory we have, for some time, been using numerical methods to determine the flow field of air within instruments such as impactors, (2) inlets, (3) and virtual impactors (4) Recently, this technique has been expanded into the three-dimensional regime, and the flow fields and particle motion characteristics within cyclones (5) and glove boxes have been studied. We have now begun to use these numerical three-dimensional flow programs to study the flow field around irregularly shaped particles to determine their drag coefficients, falling speed, and thus, their EAD."

Mar 1, 1989

This Bureau of Mines report reviews the development of the world potash industry. The trends leading to the present market situation of oversupply arid low prices, which threaten; the domestic potash industry, are presented and analyzed. Because the major threat to the domestic industry comes from Canadian imports, the report focuses on the comparative economics of United States and Canadian production. The study resulted in these major conclusions: 1. Balance of world supply and demand is foreseeable in 1975, but it could be delayed by planned expansion. 2. Balance of U.S. supply and demand could occur as early as 1974-75 or as late as 1981. 3. Nearly all U. S. production capacity vis-a-vis Canadian competition is now uneconomic. Prices cover out-of -pocket costs for only 30 percent of U.S. production. 4. U.S. producers will be undersold by Canadians in 60 to 90 percent of the U.S. market. Canadians also will have the edge over United States and European producers in export markets. 5. U.S. firms have invested in 60 percent of the planned 1971 Canadian production, and they have large holdings in Saskatchewan. 6. The decline in the U.S. potash industry probably reduced personal income in Carlsbad, Eddy County, N. Mex, the chief potash-producing area in the United States, about $21.5 million between 1966 and 1969.

Jan 1, 1970

By Ivette E. Torres

The final 26 tables of this chapter, tables 24-49, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Mainly because of the separation of the countries that formed the U.S.S.R., the column that provided a 5-year average, was deleted. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1992. This group of tables now includes each of the top 19 crude minerals in 1983 in terms of value of their output plus 3 others of lesser rank. These 22 crude mineral commodities accounted for more than 98 % of the estimated value of world crude mineral production in 1983. Coal production, included in the 1983 value of production table as two separated entries, is combined in one table in this chapter. World output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1994

By B. D. Nash

The object of this research was to investigate the technical feasibility of preparing chromium metal by the thermal decomposition of bisbenzene chromium. Bisbenzene chromium, a pi-bonded sandwich type organometallic compound, was thermally decomposed under reduced pressure to form a metal plate on a heated substrate. Metal recovery was close to 100 percent of theoretical, with deposition rates up to 20.8 mg/hr/cm2. Metal purity was dependent not only upon the purity of the starting material, but also upon the sublimation rate of bisbenzene chromium. Total detectable metallic impurities ranged from a low of 18 ppm to several hundred ppm. In general, metallic impurities were less than 100 ppm. Carbon, the major nonmetallic impurity, ranged from less than 0.3 percent to more than 10 percent. The carbon contamination is most likely a result of the decomposition of the organic portion of bisbenzene chromium. An unusual property of some of the deposits was their outstanding corrosion resistance. Unlike pure electrolytic chromium, which dissolves readily, these deposits were insoluble in hot mineral acids.

Jan 1, 1968

By John Durkin

A computer model has been generated to evaluate speech intelligibility of individuals wearing conventional and electronic hearing protectors. For speakers talking at normal levels in noise levels of 65 db(Lp) or less, it was found that conventional hearing protectors significantly reduced speech intelligibility. Under the same conditions, electronic protectors provided scores equal to those for the unprotected individuals while providing protection from high noise levels. Therefore, electronic hearing protection is valuable in areas where high noise level is intermittent.

Jan 1, 1979

By R. M. Santmayers

[This paper presents one of a series of digests of foreign mining legislation that is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining legislation of Bulgaria was prepared from a copy (in French) of the Mining Laws of Bulgaria, promulgated by Royal Decree No. 33 of I. arch. 31, 1910, and published in the "Journal Official," No. 83, April 14, 1910, and checked against a digest prepared by Maynard B. Barnes, First Secretary, American Legation, Sofia, Bulgaria, dated June 10, 1932, which was transmitted through the courtesy of the Department of State. CLASSIFICATION OF MINERAL SUBSTANCES Mineral deposits are classed either as mines or quarries. (Art. l.) Tunes are deposits, the products from which must be processed. Under this class specific mention is made of the metals (gold, silver, copper, lead, zinc, iron, chrome, titanium manganese, tungsten, tin, mercury, platinum, cobalt, nickel, cadmium, aluminum, molybdenum, bismith, uranium, antimony, arsenic), sulphur and other "analogous" mineral substances, phosphate rock, iron pyrites, sulphates, saltpeter, alum, boracic acid and its compounds, talc, asbestos, amber, graphite, merschaum and precious stories of all kinds, reek salt and other salt, peat, coal, petroleum, ozocerite, asphalt and all other bituminous substances. (Art. 2.)]

Jan 1, 1933

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

Develop an inexpensive, reliable means of quickly detecting and locating trapped miners in underground coal mines, particularly after a mine accident. The Limitations Although the Bureau of Mines has performed extensive research on the use of electromagnetics for locating trapped miners, much of its research trends toward the development of long-range systems designed to locate an underground transmitter from the surface. Such location systems are beneficial; however, there are several limitations regarding their use. Two limitations are weight and cost of the equipment. Most long-range detection systems would be too heavy and cumbersome to be accepted by miners as part of their daily protective equipment. Since such long-range detection systems are usually expensive, it would not be economically feasible for every miner to be provided with a system.

Jan 1, 1984

By E. D. Eastman

There are three researches upon the specific heat of water vapor by the method of explosion that are sufficiently advanced in technique and suitable in plan to justify careful study of their results , with the double purpose of fixing the best available experimental values and indicating the attainable accuracy of the method. These three researches comprise the work of Pier , Bjerrum , and Siegel.5 The work of earlier date than Pier's suffers from obvious inaccuracy of measurement , while the experiments more recent than Siegel's , such as those of Womersley6 , of Bone and his collaborators , and of Maxwell and Wheeler , 8 are for the most part not well designed for the accurate determination of the heat capacities in question . Some of the errors to which they are especially subject have been discussed by David and by David and Thorp.

Sep 1, 1930

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 2010

"Reports are sometimes heard of one ill effects of pneumatic tools on the hands of workmen. In consequence of such reports, Dr. Francis M. Barnes, Jr., M..D. of St. Louis, Missouri, was retained by the operators to make an investigation of conditions in the Bedford, Indiana, region, and the result of this investigation was published the Journal of the Missouri State Medical Association, Volume 16, February 1919. A brief review of this report may be of interest to all users of pneumatic tools, or operators of plants where such tools are employed.The investigation was made during December 1917, and involved an examination of general working conditions, and a careful physical examination of stoneworkers who had long used pneumatic tools. As the Bedford district is the most important structural limestone producing center in the country, the results of this investigation may be regarded as fairly conclusive as to the general effect of pneumatic tools on limestone workers."

Jan 1, 1920

By C. M. K. Boldt

The Bureau of Mines surveyed waste disposal sites at 18 metal and non-metal mines and conducted laboratory and full-scale field tests to de-termine the effects of tailings deposition techniques on physical properties of tailings pond beaches. Survey data included measurements of beach slopes, descriptions of deposition techniques, and measurements of beach physical properties taken at various distances from the point of discharge. Laboratory tests involved depositing two types of tailings, each with different grain-size distributions, into a settling trough and determining the resultant physical properties of settled materials along the length of the beach. Side confinement and the closeness of the water pool to the point of deposition caused the laboratory results to be inconclusive. Full-scale field deposition tests conducted at the tailings pond of a cooperating mine showed that there were similarities in relationships between exit velocities of tailings slurry and physical properties of the settled tailings on the beach.

Jan 1, 1988

By E. C. Perkins

This report describes a ferric chloride trap, based on formation of a low-melting sodium chloride-ferric chloride mixture of near-eutectic composition, and its use in chlorination of impure titaniferous materials. The trap is placed in the hot gas stream between the chlorination reactor and the condenser. Virtually all of the iron is removed by the trap. The condensed titanium tetrachloride is free of suspended solids and contains only a trace of iron. Four examples are given of the use of the ferric chloride trap in chlorination of impure titaniferous materials. INTRODUCTION In the Kroll process, ductile titanium metal is produced by reducing titanium tetrachloride with magnesium metal.4/ In commercial practice, titanium tetrachloride is produced by chlorinating titaniferous materials in the presence of carbon.2/ In 1957 most producers were using rutile, and virtually all plants were designed for its use. About four-fifths of the domestic consumption of rutile was imported from Australia. The Bureau of Mines, under provisions of contract DMP-116 with the General Services Administration, studied electrosmelting of domestic ilmenites and titaniferous magnetites to produce high-titanium slags with pig iron as a byproduct. Under the same contract, chlorination studies also were being made of these slags. Smelting was done at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., and chlorination at the Electrometallurgical Experiment Station, Boulder City, Nev.

Jan 1, 1958

By J. B. Gayle

A half-ton experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial, slot-type ovens. The reasons for constructing an oven of this Size, the details of the design, and the operating characteristics of the oven have been given in previous publications.3/4 The present report deals with the reproducibility of test-oven data and the effects of variations in flue temperature on the physical properties of the cokes produced. Also included are the results of 2,400° carbonizing tests for several coals and coal blends not included in the earlier reports.

Jan 1, 1955

By Connie S. Musulin

Radon concentrations in shallow uranium mines such as the Bureau of Mines experimental research mine are affected by barometric pressure changes. The radon concentrations show a significant correlation with absolute pressure; but over a period of days, a steady rise or fall in barometric pressure will result in noncorrelation of data. Fan shutdowns also affect radon concentrations, and an equation was derived to determine the time required for the radon concentration to return to normal after a fan shutdown, whether the ventilation is blowing or exhausting.

Jan 1, 1982

By D. Harrington

Coal mines and mining-, as well as metal and nonmetallic mines and min¬ing, are not inherently unsafe, although mining people think they are and would like to have everyone else think so. It is now being demonstrated that mines can be operated with essentially as much safety as any other major industrial enterprise; but most mining people, including workers as well as officials, have been slow to realize or admit this. In the past, and with most people even at present, the idea has prevailed that it is utterly impossible to operate a mine without accidents. Although, as in all other kinds of industrial activity, it is true that some injury is likely on occasion to occur to some workers and an extraordinary accident may occur to one or more persons under exceptional conditions, mines can be operated with few if any accidents if a reasonable amount of the right kind of precautionary effort is exerted and kept in effect.

Jan 1, 1934

By B. K. Cantrell, K. L. Rubow

"Quantifying exposure to diesel exhaust aerosol in an underground coal mine depends on the ability to measure this component of respirable mine aerosol separately from coal dust. Such measurement is complicated by the carbonaceous nature of both the diesel and coal dust particulate that make up the respirable aerosol. Hence, special sampling and analytical techniques must be used to distinguish between these two aerosol components.As part of a continuing study of diesel exhaust aerosol characteristics, the U.S. Bureau of Mines has applied size selective sampling together with gravimetric analysis to separate and measure respirable diesel exhaust and coal dust aerosol concentrations in diesel-equipped underground coal mines. This technique is based on the premise that the diesel portion of the aerosol is predominantly submicrometer and the mineral dust portion is mostly greater than 1 µm in size. In the study, chemical mass balance (CMB) modeling, based on the distribution of chemical elements in aerosol and aerosol source material samples, is used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.Based on the results of the study, the Bureau, in cooperation with the University of Minnesota and the U.S. Mine Safety and Health Administration (MSHA), have developed a prototype personal diesel exhaust aerosol sampler for underground coal mines. The sampler has three stages: a preclassifier stage to select for respirable aerosol, an inertial impaction stage with an aerodynamic diameter(d) size cut at 0.8 µm to separate diesel aerosol from mineral dust and collect the mineral dust, and a final filtration stage to collect the diesel fraction of the sample. The sampler has been evaluated in both laboratory and field experiments conducted by the Bureau, MSHA, and the Generic Minerals Technology Center for Respirable Dust (GMTC-RD)."

Mar 1, 1992