Search Documents

By Edward L. McHugh

The study area, which comprises 28,443 acres within the Jacumba Wilderness Study Area, is in the California Desert Conservation Area, and along the U.S.-Mexico border 25 miles west of Fl Centro, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of mining claims, known mineral occurrences, and mineralized zones during the fall of 1983. Limestone resources were identified inside the study area; tungsten resources may he present. Metasedimentary rocks intruded by Cretaceous Quartz diorite predominate in the study area. Tungsten and some gold have been found in skarn zones along intrusive contacts; limestone deposits are in the pre-Cretaceous rocks. Tertiary and Quaternary volcanic flows, pyroclastic rocks, clay beds, and diatomite in lake deposits nave been investigated for possible non-metallic resources. Evidence of mining or prospecting was found at 26 sites in or just outside the study area. In 1983, 106 claims were held in 13 claim groups. One claimant was sporadically prospecting for gold on claims in the north part of the study area in 1983, and gravel was being mined from alluvium 1/4 mile to the east.

Jan 1, 1985

By T. F. Mitchell

During the investigation or the occurrence of manganese deposits in western United States, Bureau of Mines' examining engineers collected samples from four manganese properties in the Death Valley region, California. These were supplemented by samples submitted by owners of two other properties in the same area. Extensive laboratory tests were made to determine the, amenability of the ores to standard ore-dressing concentration methods. A small sample of high-grade oxide manganese ore from the McWhinney property, San Bernardino County, Calif., was submitted by the owner. Although the sample would sinter directly to plus 48 percent manganese grade, it appeared probable that the ore, if mined in quantity, would be lower in grade and would require beneficiation. Therefore, testing was conducted to remove the chief gangue constituent, calcite. The National Resources, Inc., property (also known as the old Owl Hole mine) is in the Owl Hole Springs district, I mile from Owl Hole Springs, San Bernardino County, Calif., near the southwest corner of Death Valley National Monument. The ore deposits occur as small lenses or ,pockets, evidently .replacements in limestone and granite. Laboratory work was done on a representative sample of orb procured by Bureau engineers.

Jan 1, 1949

By S. Benedict Levin

In the spring of 1944, during the emergency In the supply of strategic mica, the Bureau core-drilled six aggregating 913 feet, at the Blister mica Trim. Cheshire County, N.H. These holes indicated a downward extension or the mica shoot which was being mined at that time and developed information essential for economic mining of the deposit.

Jan 1, 1949

By ROLLIN THOMAS CHAMBERLIN

The studies herein reported were begun as a part of researches undertaken by the United States Geologü;al Survey looking to the more effcient utilization of the coal in the United States through the reduction of waste in its extnidion, and were continued as part of further researches having regard to the conservation of the fuel resources of this country and to the lessening of injuries and fatalities in coal mining. Among other phases of the general problem to be studied were the origin of the gas whidi escapes into coal mines, its modes of occurrence in the coal and rock strata, and the conditions governing its outflow into the mines. The subject of relative danger from destructive explosions due to gas and coal dust in different mines belonging to different coal fields was to be one of the principal lines of investigation. But this work was barely under way when the series of unusually disastrous explosions in the Naomi, .Monongah, and Darr mines of Pennsylvania and West Virginia, in December, 1907, afforded an exceptional occasion to observe the behavior of explosions on a large scale. Because of the opportunities for study afforded by these terrific explosions, the inquiry originally planned was d ¡verted to the more specific investigation of the conditions in tl10SC mines, and the examinations have been directed toward finding those qualities of gas and dust which were concerned in these explosions. The following discussion, therefore, consists essentially of a report on that subject; but it is far from being exhaustive, and is to be regarded as a preliminary outline of investigations which are still in progress. The first of the three mine explosions mentioned occurred in the Naomi mine of the United Coal Company, near Bellevernon, Pa., on Sunday, December 1, at 7.40 p. m. All the men who were within the mine at the time, fortunately only 34, were killed. Less than a week later there occurred in mines Nos. fì and 8 of the Fairmont Coal Company at Monongah, W. Va., the most disastrous mine explosion yet recorded in the annals of American mining. The mines were comparatively new and well laid out. Mine No.8 had been in operation only about two years and was the pride of the Fairmont Coal Company. Mine No.6 was first opened ahout four years earlier. In order to make it possible, in case of emergency, for either mine to be ventilated by the ventilating system of the other, the two sets of workings were connected underground. The F face heading of mine K o. 6 led direetly into No.2 north heading of No.8 mine. On Friday, Dcccmber 6, at about 10.30 in the morning, an explosion of unusual violcnce swept completely through both mines, pursuing its course throughout the numerous ramifications and bursting out of the two pit mouths, located It miles apart, nearly simultaneously. The slope of mine No.6 was only slightly damaged, but at the mouth of No.8 the destruction was very great. The fan was wrecked, the engine house was demolished, and mine timbers were blown across Monongahela River: As nearly as can be determined, 361 men were killed in the two mines by the explosion. .While the inspection of the Monongah mines was still in progress, on Thursday morning, December 19, at about 11.20, a similar explosion wrecked the Darr mine of the Pittsburgh Coal Company ut Jacobs Creek, Pu.; 238 men lost their lives in this explosion, which in number of casualties is second only to the :Monongah disustcr in the history of American mining. Of ull thc men in the mine at the , time of the explosion, only one mun, who happened to be within 100 feet of the ~iUrface on an old manway in a wet, unexploded portion of the mine, succeeded in escaping alive. The underground investigation of these mines was made in cooperation with Clarence Hall and ""Valter O. Snelling, of the United States Geological Survey, and James ""V. Paul, now of the Survey but at that time chief of the department of mines for vVest Virginia, to all of whom the author is greatly indebted for valuable assistance, suggestions, and advice. Mr. Paul will rcport on the nature of these explosions, the precipitating causes, their destructiveness, and the general cüliditions in these mines following the disasters. The present report is confined essentially to the laboratory examination of some of the explosive materials collected from these mines directly ufter the explosions.

Jan 1, 1911

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By P. R. Moyer

"INTRODUCTION The Federal Explosives Act (55 Stat., 863), as amended, was passed by Congress on December 26, 1941, and became effective immediately; it amended the Act of October 6, 1917 (4o Stat., 385). The purpose of the Act was to regulate the manufacture, storage, use, and possession of explosives in order to prevent sabotage and to assure that explosives and ingredients would not fall into unauthorized hands. Under the provisions of the Act, the Director of the Bureau of Mines was authorized to administer its provisions under the supervisions of the Secretary of the Interior.EXPLOSIVES-CONTROL DIVISIONTo administer the Act, necessary personnel were employed in accordance with the appropriation made from a special presidential fund and later by Congress, and the Explosives Control Division was organized as a part of the Health and Safety Branch of the Bureau of Mines constituting the fourth division of that branch. A central office was established in Washington, D. C., and field offices were designated largely at the offices of the Health and Safety Branch throughout the country, and 50 explosives investigators were employed and assigned to work from these offices under the direction of the district engineers of the eight districts into which the United States is divided by the Health and Safety Branch. The territory assigned to each investigator was based on the approximate amount of explosives stored in that area; however, smaller territories were assigned to investigators stationed near the Pacific coast, which was indicated as critical by the armed forces."

Mar 1, 1947

By Ann G. Kim, Thomas R. Justin, John F. Miller

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, PA. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic test and subsurface temperatures was not significant.

Jan 1, 1992

By Lloyd A. Morley

Two methods are presented to determine the mechanical shaft torque as a function of time for an induction motor. The methods are based on the motor equivalent circuit and use as input variables of the motor terminal voltage, line current, input power, and power factor. One method uses all four variables and the other uses only voltage and current. The test data deals specifically with continuous miners, but the theory could be applied to other mining machines driven by multiple induction motors. Results are given for the tramming, maneuvering, cutting, and cutting with loading operations and are in the form of a minimum, a maximum, and an average of the shaft-torque time function. The theoretical development and computer implementation are discussed for both methods.

Jan 1, 1978

By J. B. Janus

This report, the 22d in a series, gives analytical data showing composition and quality of tipple and delivered samples of coal collected during fiscal year 1972. This coverage lists mines located in 20 States. Ultimate analyses are given for most of the coalbeds listed. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. The deliveries were sampled in accordance with instructions issued by the Bureau of Mines, and the samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By T. T. Read, F. C. Houghten

"The bad effects upon the health and output of miners that result when the ventilating current in a mine lacks sufficient cooling power have been described by Harrington and Sayers in a previous report (1)*** The normal temperature of the human body is about 98.5°F. and whenever work is done by the muscles, indeed even when sitting still, the normal bodily processes generate heat which must be given off, otherwise the body will become overheated and a number of bad effects will be produced. If it were possible to so enclose a man that he could continue to breathe and no heat could escape from his body he would die within a short time. In a series of experiments made at the Pittsburgh Station of the Bureau of McConnell and Houghton (2) found that a dry-bulb and a wet-bulb temperature of 112.5°F could he borne for only 35 minutes, even when the subject was at rest. A wet-bulb temperature of 100.4°F (dry-bulb 157°F) could only be tolerated for 45°F minute. Under such conditions the bodily temperature rises as much as 45°F above normal and the pulse is accelerated. Very uncomfortable sensations are felt when the pulse rate exceeds 135. The human body, like any other internal combustion engine, must be cooled in order to function properly.Under ordinary circumstances the air surroundings people is enough coder than themselves to permit this heat generated within the boiy to be river off with¬out difficulty. At higher temperatures, or when the rate of work, with its corresponding generation of heat is high, the body can not throw off heat fast enough, so it begins to sweat and the evaporation of the sweat cools the body. But the results of the experiments cited above indicate that in still air, even with the body at rent, it can not adjust its temperature when the air is above 90° wet- bulb. J. S. Haldane (4) says ""at a wet-bulb temperature of 60°F the actual amount of work done by the miner begins to fall off; as the wet bulb temperature rinse farther the work Bona gradually diminishes to the vanishing point. Then the temperatures indicated by the wet-bulb exceeds 85°F hard work in a mine seems hardly or the commercial working of a mine the wet-bulb thermometer should not in generaI, be allowed to rise above 80°F, unless perhaps where there it a good current."

Dec 1, 1923

By G. R. Fitterer, C. H. Herty

"INTRODUCTION Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis in easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot—top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel.For a large tonnage of steels which go into articles manufactured by deep—drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low—carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, — that is to say, deoxidized with manganese and perhaps a small amount of aluminum, — the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper—central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low—carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel."

Feb 1, 1931

By Fredrick L. Johnson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 25,640 acres of the 29,680-acre Devil?s Garden Lava Bed, 21,040 acres of the 28,660-acre Squaw Ridge Lava Bed, and 9,100 acres of the 12,600-acre Four Craters Lava Bed Wilderness Study Areas (OR-D01-D02, OR-001-003, and OR-001-022, respectively) in order to evaluate their identified mineral resources. The study areas are located in Lake County, OR, about 50 air miles southeast of Bend. No mineral resources were identified in the three study areas. The areas are almost entirely underlain by recent lava flows. Cinder cones occur in each of the areas; however, the best cinder occurrences are in the Four Craters Lava Bed study area. Slab lava, of facing stone quality, is scattered throughout the Devil?s Garden Lava Bed study area, and to a lesser extent, in the Squaw Ridge Lava Bed study area.

Jan 1, 1987

By L. R. Willmott

An ethanolamine purification unit for removing carbon dioxide and hydrogen sulfide from Firscher-Tropsch synthesis gas was installed at the Bureau of Mines synthetic liquid fuels demonstration plant at Louisiana, Mo. The unit was a surplus Radford Girbotol unit from the Missouri Ordnance Works modified for a capacity of 90,000 std. cu. ft per hour of synthesis gas at 450 p.s.i.g., operating pressure. The hydrogen sulfide loading of the feed gas was specified at 500 grains per 100 cu. Ft. The unit was designed by the Girdler Corp. and installed by the Koppers Co. Initial operations were conducted far 11 days in May 1951. Thereafter 7 additional runs were made, varying lo duration from 8 to 54 days. The last run was terminated on May 29, 1953, the total time the Plant wars in operation being 219 days.

Jan 1, 1956

By Robert J. Evans

Capital and operating costs were estimated using a wet suppression, fabric filter, and a combination system of the two for hypothetical hard rock stone crushing plants located in central Pennsylvania, operating at 300, 600, and 1,000 tons per hour. Fixed capital expenditure for the dust abatement systems ranged from $49,129 to $249,162. Annual operating costs for the dust abatement systems ranged from $8,394 to $46,606 (0.9 to 3.2 cents per ton). If these dust abatement systems are properly sized, installed, and maintained, efficiencies approaching 95 percent can be expected for reduction in weight of dust particles emitted before control.

Jan 1, 1975

By E. D. Eastman

The basic character of the free energy r data relating to water and the oxides of carbon makes it desirable that the most representative values that can be obtained should be constantly available. The calculations of Lewis and Randall3 retain much of their of original value, but appear to require some modification in the light of more recent work. This paper has been written to incorporate the newer information and to present some estimate of the reliability of the resulting figures. The data upon which the calculations are mainly based are, for these substances, the equilibrium constants of the various reactions involved. The original work relating to these equilibria has, been reviewed and, where possible, weighted to correspond with its probable reliability. The differences in the results of the present from the earlier calculations are partly the consequence of this appraisal and partly of the inclusion of more extensive data, as will be indicated in detail in the succeeding sections.

Jan 1, 1929

By Robert L. Marovelli

The thermal conductivities of six rocks were measured by the transient line source method over the temperature range of -850 to 1,500° F. Close-fitting ceramic probes were used in 0.065-inch-diameter holes drilled through 5-to 6-inch-thick rock specimens. Taconite, granite, quartzite, and basalt were used in the tests. The method yields absolute data and is applicable to both laboratory and in situ measurements.

Jan 1, 1965

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 B. t. u. compared with 597,000 B. t. u. in 1936. These amounts represent roughly the heat obtainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at refineries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels were 11 percent higher than in 1930; the average operating ratio was 83 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 638,149 billion B. t. u. in 1936 to 663,966 billion B. t. u. in 1937.

Jan 1, 1938

By J. H. Adkins

The purpose of this research is to identify hazards associated with roof bolting and to make recommendations for procedural and equipment design changes to reduce those hazards. To that end, the project reviewed Literature on related research, collected and analyzed roof bolting injury data, normalized the injury data be exposure time to each activity and identified problem areas within the root bolting tasks. In addition, field data collection forms were prepared and mines selected for field work. In the field, observations were made of eighty (80) different roof bolting crews bolting one hundred fifty-five (155) place;, on forty (40) sections spread among nine (9) mines. Task analysis forms were used to record unsafe behavior or conditions for each crew and each place. Informal discussions were held with the mine's safety and training officer, the maintenance officer, one section foremen and, when possible, the observed crew, concerning the training and experience of the miners. Unsafe acts were categorized and related to the "Activity While Injured" categories developed during the accident analysis. For each of these categories one or more recommendations for corrective measure, machine modification, procedural change or job training were developed. The study produced over fifty (50) specific recommendations involving machine design, procedural, safety training and supervisional issues that would lead to reduced roof bolter injuries in the near term. The authors concluded, however, that only the development of truly hands off/remote bolting can eliminate or reduce to an absolute minimum the hazards to which the roof bolter is subjected.

Jan 1, 1977

By R. L. Grayson, S. S. Peng

"Abstract. Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include:l. Respirable mass concentration, 2. Mineral composition,3. Particle size distribution by mineral,4. Particle shape distribution by mineral,5. Particle angularity distribution by mineral, and6. Respirable size distribution.Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.INTRODUCTIONThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from dangerous exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al. (1971) whi3h has been used to establish the 2mg/m exposure limit in the United States. According to the model, exposure to respirable dust for 35 years at this level or less would prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP). The exposure limit, of course, must be adjusted whenever greater than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mass concentration exposure, which showed the highest correlation with incidence and progression of CWP. As Morgan; et al. (1973) noted, howev.er, the quantity of respirable dust inhaled is not the only significant factor. It is noted that although mass of respirable dust correlates highest with the incidence of CWP, it is not a causal factor. Indeed, the insidious processes causing the disease occur on the cell-particle scale, requiring microscopic investigation."

Mar 1, 1989

By George S. Rice

"The author was a member of a Commission sent by the Secretary of the Interior to France to investigate developments in mining and metallurgy under stress of war conditions, and also to observe the extent and character of the destruction of the collieries and the steel and iron plants, and methods which were being taken to reestablish them. This commission consisted of F. G. Cottrell, Chief Metallurgist of the Bureau of Mines, Frank H. Probert, Dean of the University of California Mining School, and George S. Rice, Chief Mining Engineer of the Bureau. While conducting this investigation a trip was made to the Saar Basin to observe the conditions there. Following this Mr. Rice acted as advisor on mining matters to the Representative of the Economic Council in an Interallied conference held at Cologne in April 1919, and subsequently visited the mining districts in central and southern France, Belgium, and Great Britain.The Germans, in planning a campaign for world supremacy, had as one of their first objectives the seizing of the important Briey iron ore deposits of France and the coal fields of Belgium and northern France.Large resources of coal and iron have led to the commercial greatness of the countries possessing them, as exemplified by the great development first in England then in the United States, and in Germany when the minette high phosphorus iron ores became useful through the invention of the Thomas and Gilchrist dephosphorizing process in 1878. However, this development was anticipated by the German scientific advisors in 1871, and led to the then known deposit of minette ore in Lorraine being taken from France by Germany.When these ores became available, Germany made such tremendous strides that its minette ore developments were not sufficient and importation of ore was necessary. Meantime France, by drilling, had established the extension of the minette ore field into French Lorraine. Then it was discovered that France had greater resources, while the German resources were being rapidly depleted.Although Germany, in its Westphalian basin, possessed the most important coal field on the Continent, containing the largest resources in coking coal outside of Great Britain, its coal was distant from the sea coast, so it could not be an important factor in the export business. No doubt this fact caused the German Imperialists to look forward: to securing the coal basin of Belgium and northern France for future ocean trade.It was a striking feature in the German conduct of the war that, although the steel and iron plants of Belgium and France and other industrial establishments in the invaded regions of Belgium and France were utterly destroyed, the iron mines in French Lorraine were not destroyed nor materially damaged by the Germans in their retreat, while the destruction in France continued until the day of the Armistice. The other striking fact is that the coal mines Of Belgium were not destroyed. It can only be conjectured whether this was due to President Wilson's threat of retribution, which did not stay their hand in France, or was due to the fact that they did not consider Belgium as a real competitor. It was evident they wished to cripple France industrially when they could not hold these northern provinces."

Dec 1, 1919