Search Documents

By John W. Adams, W. D. Bensema, Motohisa Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Robena No. 4, located near Waynesburg, Pennsylvania. One technique measures noise over the entire electromagnetic spectrum of interest for brief tine periods. With present instrumentation, the spectrum can be covered from 40 Hz to 400 kHz. It is recorded using broad-band analog magnetic tape, and the noise data are later transformed to give spectral plots. The other technique records noise envelopes at several discrete frequencies for a sufficient amount of tine to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and amplitude probability distribution plots. The general results are that at frequencies below 10 kHz, power line noise within the mine is severe. Impulsive noise is severe near arcing trolleys, and at lower frequencies near any transmission line. Carrier trolley phone signals and harmonics are strong throughout the mine whenever the trolley phone is in operation. Additional information beyond that included in this report may be obtained from the authors, who are with the Electromagnetics Division of the National Bureau of Standards.

Jan 4, 1974

By Carlton E. Brown

Broom and Yant6/ recently described a. microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter) and the thermal precipitator8/ . This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a micrcprojection method for counting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the ventilation Department of the Anaconda Copper Miring Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By H. C. Miller

Several agencies of the Federal Government are engaged in research and fact finding relative to petroleum and natural gas, and others are concerned with carrying out the provisions of specific laws that affect these natural resources in their broad aspects. The Bureau of Mines, however, is the only Federal agency designated by law to engage in research in oil and natures gas production, chemistry, refining, and

Jan 1, 1941

By Thomas Fraser, E. A. Holbrook

The data in this bulletin were obtained during an investigation of screening practice by the University of Illinois engineering experiment station and the United States Bureau of Mines under a cooperative agreement between them and the State of Illinois Geological Survey Division. Earlier work on this subject includes a study of the general practice of coal preparation in Illinois, made in 1914 and published in 1916/ and an investigation of Illinois coal-w.ashing methods, results of which were published in 1912 in a bulletin 2 that contained complete information on the methods then in use for sizing washed coa 1.

Jan 1, 1925

By Robert J. Shanley

The computer program, HYBMODE, has been developed to meet the need for a fast and economical method for clustering data points on the sphere. The algorithm used in this development is an extension of D. Wishart's one-level mode analysis. The program can be used to cluster either vectorial or axial data; it is currently being used by the Bureau of Mines to cluster fracture orientations.

Jan 1, 1974

By A. Baldwin

This report describes the engineering feasibility and economic advantages of a unique new mining machine using cutting bits that take a constant-depth linear cut in the coal face. The studies show that this innovative new cutting concept, being developed by the Bureau of Mines, can be designed into the basic continuous mining machine. The resulting miner would be attractive to mine owners because coal could be mined with minimum generation of airborne respirable dust, substantial increases in productivity, and elimination of methane ignition due to cutting.

Jan 1, 1977

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

By Constantine C. Popoff

Several limestone deposits in western Washington were examined by the Bureau of Mines in 1946. This report presents data obtained from the investigation of limestone deposits in the vicinity of Arlington, Snohomish County, Wash. The work consisted of surface surveys and sampling. Samples were taken where complete, or nearly complete, sections of limestone were exposed or where individual beds were exposed at a number of separate .localities. Areas were cleaned by blasting prior to sampling. Channel samples were cut where practical; otherwise chip samples taken. Twenty-one samples were taken. The locations of the samples and the analyses are shown on maps accompanying this report.

Jan 1, 1949

By Norma Golumbic

The primary purpose of the Bergius (hydrogenation of coal) and Fischer-Tropsch (hydrogenation of carbon monoxide) processes is the production of synthetic liquid fuels. This objective is of importance in insuring an adequate supply of motor fuels and lubricating oils in the United States. In the urgency of the basic research and process development work on synthetic liquid fuels, the possibilities for the production of synthetic chemicals inherent in these processes have hitherto received little attention in this country. However, the by-products, as well as the primary products, from the Bergius and Fischer-Tropsch processes are rich source materials for organic chemicals. The overhead oil from liquid-phase hydrogenation of coal, for example, contains benzene, toluene, xylene, cyclohexane, methylcyclohexane, aromatic solvents, about 20 percent tar acids (largely phenol, cresols, and xylenols), and 3 percent nitrogen bases. Wax, alcohols, and acids are by--products of the Fischer-Tropsch synthesis. In addition, techniques have been developed which make possible the production of aliphatic hydrocarbons, alcohols, acids, aldehydes, and other oxygenated organic compounds. These chemicals are more valuable on a unit basis than gasoline. Because of continued rapid expansion of the plastic, resin, lacquer, and solvent industries, larger amounts of many of these chemicals will be needed in the near future.

Jan 1, 1949

By H. V. Makar

An aluminizing dross which is accumulating as a waste material in substantial quantities was tested for possible use as a steel deoxidizer. This material, consisting mainly of aluminum, silicon, and iron, was used to deoxidize laboratory-scale melts ranging from 7 to 100 pounds. Oxygen analysis showed that the aluminizing dross was effective in reducing oxygen levels in steel. A direct comparison with aluminum wire showed the dross material to be at least as effective. Under similar test conditions with 7-pound melts, 3 grams of aluminum reduced the oxygen concentration from 210 to 175 ppm, while 4 grams of aluminizing dross (equivalent to approximately 2 grams aluminum) reduced the oxygen concentration from 250 to 170 ppm. An additional 4 grams of aluminizing dross produced a final oxygen concentration of 140 ppm.

Jan 1, 1972

Spectrochemical methods were developed to determine beryllium in the concentration range 0.0015 to 4.0 percent in siliceous mineral beneficiation products. Two methods are described. They are (1) a fusion-pellet-spark procedure (spark method) and (2) a sustaining alternating-current arc procedure (arc method). In the spark method the sample is fused with lithium tetra-borate and vanadium pentoxide. The resulting bead is crushed, mixed with powdered graphite, and briquetted. This is analyzed spectrographically using controlled high-voltage spark excitation. In the arc method the sample is diluted with germanium metal, graphite, and vanadium pentoxide. Weighed charges are packed into cupped graphite electrodes and subjected to excitation with a sustaining alternating-current arc. Vanadium serves as internal standard for both methods. Effects due to matrix variations in samples and standards are eliminated either by fusion with lithium tetraborate in the spark method or by dilution with germanium and graphite in the arc method. Beryllium determinations show deviations from accepted chemical values of approximately 5 and 8 percent for the spark and arc methods, respectively. Analyses can be made more rapidly by the arc procedure with a sacrifice in precision and accuracy. Either method can be applied to the determination of beryllium in silicate rocks.

Jan 1, 1962

By R. R. Sayars

"Carbon monoxide is a gas slightly lighter than air, with which it diffuses readily to make a homogeneous mixture. It will burn and has a wide explosive range, that is, an explosion is possible when the air contains from 15 to 73 per cent of the gas3. This explosive range is about the same as that for hydrogen and over nine times As Tide as that for marsh gas (methane). Like air, it has neither color nor taste and has no odor in concentrations usually encountered, therefore it cannot be detected by the ordinary senses with which men are endowed. It is produced by burning carbon containing fuels, no coal, wood, gasoline, etc., whenever not enough air or oxygen is supplied to burn and oxidize the fuel completely.The human race has probably been exposed to this gas since men first began using fires in confined or sheltered places. The poisoning as usually encountered is an acute condition resulting from breathing atmospheres con¬taining this gas. A number of eases described in the ancient literature Indicate that carbon monoxide was a frequent cause of death by accident, suicide and is a means of punishment or torture. A quotation by Lewin from Aristotle who lived in 384-322 B.C., states that ""animals collapse from harmful odors as men gets a severe headache and often dies through charcoal vapors"". The Roman knew that smoke was poisonous, and used the greenest most smoke-producing wood to put persons to death. The occurrence of carbon monoxide increased in frequency through the years until at the present time it is found in the home as well as in many industries. The following table gives the approximate percentage of carbon monoxide found in gases from various sources of poisoning.4"

Apr 1, 1924

By Frank B. Fulkerson

Barge traffic on the Nation's inland waterways over the past 15 years has been increasing at a rate much faster than intercity freight traffic by all modes, largely due to the growing consumption of mineral commodities, development of more powerful towboats and large and more specialized barges, improvements to loading and unloading facilities, and competition among bargelines for contract shipment of bulk commodities. The Bureau of Mines, in a study to determine barge traffic projections for inland waterways in the South-Central States to the year 1980, gathered data on origin-destination patterns by commodity, quantity moved, equipment used, and rates charged; the trend of each of these factors over time; and the extent of competition between water trans-port and other means of transportation. The Mississippi River and the Gulf Intracoastal Waterway, which together carryover half the Nation's barge traffic, are major carriers of coal, crude petroleum, steel, marine shells, sulfur, salt, cement, and alumina. Greater quantities of these products will be transported by barge; however, oil pipe-lines and unit trains for coal are expected to limit increased barge traffic of these two commodities. Increasing quantities of fertilizer materials will be transported upstream. Although congestion at certain locks is a current problem, the Mississippi River below St. Louis and other open-river stretches have the capacity to handle the increasing number of barges for the foreseeable future.

Jan 1, 1969

By S. D. Cramer

Corrosion research is being conducted by the Federal Bureau of Mines to determine suitable construction materials for geothermal resource recovery plants. As part of this research, the corrosion resistance of 31 iron-nickel-, aluminum-, copper-, titanium-, and molybdenum-base alloys was characterized and evaluated in laboratory corrosion studies in low-and high-salinity geobrines representative of those found in the Imperial Valley, Calif. General, crevice, pitting, weld, and stress corrosion were measured at 105° and 232° C in deaerated brines and brines containing dissolved 02, C02, and CH4 General corrosion rates in deaerated brines at 105° and 232° C were usually below 5 mpy for the alloys tested except carbon steel, the low-alloy steels, Monel 400, 70-30 cupronickel, and the aluminum-base alloys. Dissolving carbon dioxide and methane in the brines at 2320 did not markedly alter these results. However, the introduction of oxygen, which can enter the brine during process operations, seriously degraded the corrosion resistance of many alloys by increasing the incidence of stress corrosion cracking, crevice corrosion and, except for the titanium-base alloys, pitting. In deaerated brine at 2320 C, the general corrosion rates for carbon steel and the low-alloy steels were relatively unaffected by pH in the range of 6.1 to 3.0. However, general corrosion rates increased sharply below pH 3.0. In deaerated brine at 232° C, welds in several iron-, nickel-, and titanium-base alloys corroded at rates comparable to the general corrosion rates of the alloys, but the addition of oxygen to the brine increased corrosion rates for welds in Inconel 625 and E-Brite 26-1. Alloys exhibiting good corrosion resistance in the deaerated Salton Sea KGRA-type brine at 232° C were E-Brite 26-1, Inconel 625, Hastelloy S, Hastelloy G, Hastelloy C-276, TiCode-12, Ti-0.2Pd, Ti-2Ni, Ti-1.7W, and TZM. The alloys most resistant to corrosion in oxygenated Salton Sea KGRA-type brine at 232° C were the titanium-base alloys. These alloys appear the most suitable for use in the construction of geothermal resource recovery plants. Carbon steel and the low-alloy steels are unsatisfactory for high-temperature, high-salinity brines and alternative low-cost materials with improved corrosion resistance should be sought.

Jan 1, 1980

By John C. Machisak

THIS INFORMATION CIRCULAR contains 1956 and 1957 injury experience and employment data for metal mines in the United States and Alaska. Unlike previous publications, this report covers only metal mining and contains statistical data on injuries and employment pertinent to metal mines and mills reporting voluntarily to the Bureau of Mines on an annual basis. Injury and employment data for the nonmetal industries, which from 1911 through 1955 were published in the same series as the metal industries, for the first time will be published separately as an information circular entitled "Injury Experience in the Nonmetal Industries, 1956 and 1957." The Bureau of Mines is authorized to make requests for injury and employment data, and the information submitted by operators of metal mines and mills is a step forward in promoting safety in the metal-mining industry. Every effort has been made to make this coverage as complete as possible.

Jan 1, 1960

U.S. Bureau of Mines contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment", was an investigative effort involving: ? Study of the fire problem on large mobile mining equipment ? Identification of equipment most prone to fire, to serve as a design case example ? Design of an improved fire protection system ? Demonstration of the developed system This effort was performed during the period June 1972 through May 1973, and was conducted in two phases. Phase I, June through November 1972, was devoted to identifying the fire problem and developing and evaluating design criteria. Phase II involved translating the design into hardware and demonstrating its effectiveness during actual fire tests, first on a wooden mockup of a truck, then on an operating truck at a working mine site.

Jan 1, 1973

By J. R. Thoenen, J. D. Warne

"INTRODUCTION Red-iron-ore deposits in northeast Alabama have been exploited at vari¬ous times for nearly 6o years. About 3-1/2 million tons of ore have been produced in the Gadsden district; but mining activity has been dormant since 1926, and furnaces within this section of the State now suffer a shortage of red ore.To alleviate these shortages, work by-the Bureau of Mines was recommended after preliminary investigations. 4/5/ Diamond drilling, to determine the lateral and vertical extent of ores of known deposits in Greasy Cove and on Shinbone Ridge, was done from August 1946 to May 1947, as Project 9-106, Alabama Red Iron Ore. Three holes were drilled in each area.ASKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of domestic mineral resources to the end that they- make the greatest possible contributions to the national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as possible after its conclusion. The Mining Division, Lowell B. Moon, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests."

Jun 1, 1948

By Knox Van Dyke, Vincent Castranova, Lixin Wu, Mark J. Reasor, James M. Antonini

"One of the proposed mechanisms involved in the pathogenesis of silicosis is that inhaled silica dust activates a ""respiratory burst"" in pulmonary phagocytes, such as macrophages and neutrophils. This increase in oxidative metabolism results in enhanced generation of reactive oxygen species which if produced in excess, would overwhelm natural defense mechanisms and cause damage to the lung parenchyma. This damage would then result in scarring, fibrosis, and decreased gas exchange.Weiss and LoBuglio' have listed several oxygen species produced by phagocytes which may be involved in cellular injury. These oxidants include superoxide anion, hydrogen, peroxide, hydroxyl radical, and hypochlorous acid. Superoxide anion (0;) is generated from molecular oxygen by the plasma membrane bound enzyme NADPH oxidase according to the following reaction:Once generated, superoxide anion can form hydrogen peroxide:In the presence of myeloperoxidase and halide, hydrogen peroxide can form hypochlorous acid:Superoxide and hydrogen peroxide can also form highly reactive hydroxyl radicals. Hydroxyl radicals can be generated slowly by the Haber-Weiss reaction:In addition. hydroxyl radical production can be catalyzed via the Fenton reaction:Hydroxyl radicals can also be generated from the reaction of superoxide and hypochlorous acid as follows:Recent investigations suggest that, in addition to the reactive oxygen species discussed above, nitric oxide may be a potential mediator of silica-induced toxicity.2-4 Nitric oxide (NO') can be generated by the cytosolic enzyme nitric oxide synthase according to the following reaction:NO synthase exists in two forms. i.e.. a constitutive. Ca2+-calmodulin-dependent form and an inducible. Ca2+-calmodulin-independent form. In pulmonary phagocytes. the activity of the constitutive form of NO synthase is low. However. NO synthase can be induced in macrophages and neutrophils by a variety of stimulants such as lipopolysaccharide. interferon y. chemotactic peptide, platelet activating factor, or leukotriene B4.3.5Once generated. nitric oxide can combine with superoxide anion to form peroxynitrite as follows:Peroxynitrite is a potent oxidizing agent. In addition, peroxynitrite can form peroxynitrous acid. which in turn can produce hydroxyl radical and nitrogen dioxide (all of which exhibit strong oxidizing potential) by the following reactions:Oxygen metabolites have been shown to cause lung damage in vivo.6 Such damage includes edema. leakiness of the alveolar endothelial/epithelial barriers, and airway constriction.7 Superoxide and hydrogen peroxide have been associated with membrane damage and cell lysis.8 These oxidants have also been associated with alteration of cytoskeletal structures at cell-cell junctions and elevation of transepithelial conductance in cultured monolayers.9 Macrophages or neutrophils can be stimulated by bacteria or phorbol myristate acetate to produce sufficient oxidant levels to lyse lymphoma cells.10 This cell killing is inhibited by catalase but is unaffected by superoxide dismutase. hydroxyl radical scavengers. or azide. i.e., an inhibitor of peroxidase. This implicates hydrogen peroxide as the active oxidant. Similarly. Weiss et al.11 have reported that hydrogen peroxide is critical in the death of cultured endothelial cells due to neutrophil activation. In addition. hydroxyl radicals generated by monocytes have been associated with cell injury.12 Lastly. peroxynitrite has been shown to oxidize sulfhydryl groups and to inactivate proteinase inhibitor making the lung more susceptible to damage caused by phagocytotic enzymes.' Therefore. a strong case can be made that activated pulmonary macrophages and neutrophils are capable of causing oxidant injury. This chapter presents in vitro and in vivo data indicating that silica is associated with the production of reactive oxygen species from these pulmonary phagocytes."

Jan 1, 1998

By J. Dean Warner

In 1984, as part of a project to evaluate Alaskan occurrences of certain critical and strategic minerals, the Bureau of Mines investigated a columbium-bearing regolith on upper Idaho Gulch, near Tofty, AK. The regolith is derived from weathering of a dolomitic marble and consists mostly of iron oxide minerals with accessory apatite, zircon, xenotime, rutile, monazite, and the columbium minerals aeschynite, columbite, and ilmenorutile. Two regolith lenses contain 340,000 lb of columbium resources at an average grade of 0.07 pct. Calculated composite concentrates from two regolith samples (approximately 200 lb each) contained 53 and 57 pct of the columbium at grades of 0.97 and 0.86 pct, respectively. In each case the grade could be improved to 1.1 pct Cb with a sacrifice of 9-pct recovery. The regolith's mineralogy, trace-element geochemistry, and similarity to descriptions of other columbium-enriched regoliths suggest that the underlying marble may be a carbonatite. The lack of associated alkalic igneous rocks and the stratiform nature of the regolith, however, may be interpreted as evidence for sedimentary origin of the marble. The marble and regolith are a lode source for some of the minerals in the Idaho Gulch placer deposit.

Jan 1, 1986