Search Documents

By David G. Winter

The Olive 8 excavation site in Seattle was surrounded on three sides by conditions requiring innovation, careful modeling, and extensive instrumentation to support use of a first-of-its-kind shoring system. The solution combined heavy soldier piles, long and steeply angled tieback anchors, and tightly spaced soil nails to support surcharge loads from a 33-story adjacent tower separated by a narrow alley housing critical utility lines. Land restrictions on two other sides of the site also required innovative applications of traditional methods. The Olive 8 project has won three state and local awards for innovation and has been reported on in Engineering News-Record and has been the subject of two feature articles in the Seattle Daily Journal of Commerce. This paper presents the conditions and site challenges, reviews the design analysis, discusses the shoring performance, and looks at other potential applications.

Jan 1, 2009

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017

By Kazunori Matsushita, Frank Vespi, Emi Walder, Mitsuo Nozu

During the runway expansion project at the Fort Lauderdale-Hollywood International Airport in Florida (FLL project), therewere complicated geotechnical issues with a number of cavities in the limestone-loose sand mixed ground thatexisted in many areas below the existing ground. Collapsing the cavities and compacting the runway foundation to secure the take-off and landing of aircrafts was a necessary requirement for the project. The Mammoth Vibro-Tamper (MVT) which produces less vibration and noise level, was proposed and accepted as the alternative to the originally specified Deep Dynamic Compaction (DDC) for the runway with its length of 1.5 miles and area of 570,000 square yards. In this report, the shallow compaction effect and reduced ground vibration with the MVT are presented in comparison with the DDC which was utilized on the same project in a different area of the airport. INTRODUCTION MVT was developed by Fudo Tetra Corporation in the 1960’s and has been widely used in Japan (more than 14,400,000 square yards). For example, at the Kansai International airport, a large area including aprons was compacted with the MVT. It is capable of compacting up to approximately 5m in depth by using a heavy steel plate (3m x 3m) and a strong vibrator motor (V-180, 10Hz) on top of the steel thick plate with specified time duration. We were involved in densification work with the MVT at the Fort Lauderdale Airport Project (Figure 1) from June, 2012 to February, 2014. Deep Dynamic Compaction (DDC) was originally specified as the compaction method to secure the relative density over 70% in every 2,000 square yards grids, however, we proposed the application of MVT to reduce the vibration risk and it was accepted as the alternative (Figure 2). The compaction work was completed in February 2014, without causing any delay in regard to the residual settlement due to the high embankment (H=60ft=18m).

Jan 1, 2018

Jan 1, 2001

By Gray Mullins

This paper presents results from model and full-scale tests to assess the interface bond between a cast-in-place concrete seal slab and steel H-piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid was displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also tested. In the model tests, eight 15 cm deep, W6 x 15 sections were used for two different embedment depths of 1.5d and 2d, d being the depth of the section. In the full-scale tests, 16 specimens 35 cm deep (W14 x 90 sections) were tested with the embedment varied between 0.5d-2d. The results show that significant bond stresses developed even in the worst placement condition. Recommendations made for revising current values in specifications have already been implemented by the Florida Department of Transportation.

Jan 1, 2013

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By Ganesh Kumar S.

"Soil reinforcement using stone columns is one of the well-developed ground improvement techniques for soft clay deposits. The load carrying capacity can be further improved by encasing it with geosynthetic material around the column which offers effective lateral confinement, prevents column contamination with improved drainage and strength characteristics. Improvement of undrained shear strength using vacuum consolidation is a type of hydraulic modification technique in which negative pore pressure will be developed which increases the effective stresses in soil without changing the total stress. The improvement in effective stress resulted in improved undrained shear strength of surrounding soil. In this research work, combined geosynthetic encased stone column and vacuum treatment method is examined for improving of extremely soft clay soils. The improvement in the time rate of consolidation and load carrying capacity of stone columns after vacuum treatment was studied using experimental investigations. It was observed that both load carrying capacity and stiffness of the encased stone column increased significantly with vacuum application. Also, application of vacuum accelerates rate of primary consolidation settlements. With this reduction in time, the construction activity can be accelerated which makes the project economically beneficial.INTRODUCTIONThe rising demand for the land for country’s infra-structure compels the engineers to work with even soft clay deposits which are not suitable for construction activities. As these soils have low bearing capacity and excessive settlement characteristics, ground improvement methods will be required before commencing construction. Among all available treatment methods, soil reinforcement and hydraulic modification technique are well-known popular techniques for its reduction in time required for consolidation settlement with improvement in load carrying capacity. When stone columns are used as a reinforcing member, it creates drainage with improves bearing capacity (Greenwood, 1970; Mitchell & Huber, 1983). However, the limitation includes lack of lateral confinement in very soft clay deposits, possibility of contamination, reduction in drainage path all which leads to the failure of stone columns (Mckenna et al, 1975). To overcome these limitations, encasement using geosynthetic material was adopted around the column which offers better lateral confinement, prevents intrusion of finer clay particle inside the column and provides effective drainage path with improved load bearing capacity characteristics (Van Impe, 1986; Raithel et al. 2005; Short et al. 2005; Borkemper et al. 2006; Murugesan & Rajagopal 2010; Kumar et al. 2014)"

Jan 1, 2017

By Chris G. Leach

"Abstract A seven storey Northbridge area of Perth, Western Australia presented residential apartment complex located in the an opportunity for a novel application of Cutter Soil Mix technology (CSM). The development included a two-level basement for car parking which covered the full site area. However, the basement was also required to extend under an existing single story heritage building. Soil conditions comprised 2m of fill overlying medium dense to dense sands that in turn were overlying a very stiff clay stratum at approximately 14-16m depth. The ground water table was located at a depth of approximately 1m below the natural surface level.A site boundary consisting of a reinforced CSM retention system and was designed and installed to allow the excavation to proceed to basement level. Two rows of temporary soils anchors or inclined struts were required to achieve this. A CSM support system for the heritage building was also designed and constructed to provide temporary support during excavation and permanent construction works. The brief for the contract works emphasised that it was vital that settlements of the heritage building be kept within strict limits.CSM is a relatively new introduction to the Australian construction market, using a modified trench cutter to mix a binder slurry with in situ soils, generally to form cut-off walls, retaining walls and soil improvement works. This project is understood to be first application of the CSM for underpinning work in Australia.This paper discusses the site background details leading to the decision by the client to adopt CSM technology, and the design and construction aspects to meet the challenges offered by this project.Introduction190 Newcastle St is a 7-level residential apartment complex located in the Northbridge area of Perth, Western Australia. The development includes a 2 level basement for car parking, which covers the full site area. The basement also extends under a single story heritage building, which remained in-situ throughout the building works.A site boundary retention system was required to allow the excavation to basement level to proceed. In addition, a support system for the heritage building was required to provide temporary support during excavation and permanent construction works."

Jan 1, 2014

By Liu Run, Jia Zhao-lin, Yan Shu-wang

"Piles with diameter larger than 2m in engineering can be defined as large diameter pile, and piles used for oil platform foundation in Bohai Gulf, are usually over 100m long and 2m in diameter. Such long piles have to be manufactured by segments before installation, because of transformation and hoisting difficulties. The segments of the pile are assembled by welding during installation one to another. Normally, assembling two pile segments takes one day or even a longer time, which mainly depends on construction conditions. After pile segment assembling, it proves to be difficult to restart the successive penetration. The mechanism of pile refusal is discussed and the process of driving a segmented pile is simulated with a finite element program. The calculating results show that, when the stick-up stability was satisfied, increasing the length of the last segment of the pile and assembling the pile segments when the pile tip penetrates into a clay layer could greatly ease the difficulty of driving the pile. Furthermore, cutting down the pile extension time is also one of the most effective measures to minimize the refusal risk.1. InstructionIn recent years, more and more oil platforms with six or eight legs have been adopted in Bohai Gulf, China. The leg piles with diameters of 2m or more have to be driven to about 100m below the sea bed. Such long piles have to be manufactured by segments before installation, because of transportation and hoisting difficulties. The segments of the pile will be assembled during installation, in which a successive segment will be attached to a formerly penetrated one by welding (Fig.1). The assembling work often takes one day or even a longer time."

Jan 1, 2014

By Steven R. Musselman

The bending strength and flexural stiffness of a micropile at its threaded connection is less than its intact strength and may fail due to thread slippage or by fracture through the pin (reduced cross-sectional area of male threads in the threaded zone of the casing). The mode of failure depends on the reduction in cross-section necessary for machining the threads, and details of the threaded connection such as the length of threaded connection, size and shape of threads, and the thread density (threads per inch). Based on data from bending tests conducted on 9-5/8 inch diameter micropile casing, a method has been developed to predict the ultimate moment capacity and initial bending stiffness of round threaded micropile connections. Two modes of failure were observed from four-point bending tests conducted at the University of Illinois on 9-5/8 inch casing with round threads. Threaded micropile casing connections with an effective thread length of 1.35 inches typically failed by slippage at the threads (jump out), while connections using an effective thread length of 1.89 inches failed by fracture of the pin. These two failure modes were described by W.O. Clinedinst in his report to the American Petroleum Institute on tension tests of threaded pipe casing. Clinedinst developed an empirical formula to determine the tensile strength of threaded connections. A method to predict moment capacity for threaded micropile connections by modeling the micropile cross-section and applying Clinedinst?s equation to determine the max tensile stress along the threaded connection while satisfying force equilibrium is proposed. The predicted moment capacity for threaded connections using this approach is within ten percent of measured for both modes of failure observed from the bending tests.

Jan 1, 2007

By Mohammed Sakr

This paper presents the results of a full-scale axial compression and tension (uplift) testing program executed on large-capacity helical piles installed in very stiff to very hard clay till soils (i.e. cohesive soils). A total of ten tests including six axial compression tests and four tension (uplift) tests were carried out. The results of the axial compressive and tensile pile load tests and field monitoring of helical piles with either a single helix or double helix are presented in this paper. Helical piles are traditionally used to support light to medium loads (i.e. loads up to 500 kN or 56 tons). However the results of the present study confirmed that helical piles can support significantly higher axial compressive loads up to 2450 kN or 275 tons, which is about 5 times traditional design loads. The study also demonstrated the high tensile capacities of helical piles which was as high as 85% of their compressive capacity. Hence helical piles can provide a viable design option for foundations supporting relatively heavy loads.

Jan 1, 2012

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

By Michael Quadagno

Hudson River Pier 86, home of the historic USS Intrepid Aircraft Carrier and the Intrepid Sea-Air-Space Museum, is currently undergoing a $30M reconstruction. This project involves the demolition of the old timber pile supported pier and construction of a new 150 ft wide by 782 ft long concrete pier, built over the footprint of the old piles. The new pier consists of steel pipe piles, precast concrete pile caps, and a composite deck, made up of precast, prestressed concrete planks and cast-in-place concrete topping. This paper focuses on both the structural design and construction of the new pier, with emphasis on the pile foundation. Pier 86 is unique in that it is required to resist the extremely high lateral loads imposed on it by the permanently moored 898 ft long aircraft carrier during severe storms. A total of 360 steel pipe piles support the new pier. These piles, which are 24 in. in diameter and range in length from 58 ft to 175 ft, were driven down to bedrock. The piles, each having 200 ton allowable capacities, work together to resist the significantly large lateral loads exerted on the pier by the ship. The installation of the piles was unique in that all the piles, including the ?super-longs?, were fabricated to-length offsite, delivered to the site via truck and barge, and installed in one piece, eliminating the need for field splicing. The Pier 86 reconstruction will be completed within an extremely aggressive 18 month schedule, from January 2007 through June 2008. The refurbished aircraft carrier Intrepid will return home in September 2008, and the grand re-opening of the pier will be on Veteran?s Day 2008. This paper provides a case history for owners, government agencies, engineers, and construction professionals that will be faced with the challenges of designing and building new piers.

Jan 1, 2008

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987

By Jamie D. McEwan

To cater for the future introduction of 12 car trains, London Blackfriars railway station is being extended from the north end to span across the River Thames. Following the demolition of existing buildings, a number of challenges had to be overcome including working adjacent to a live railway line, above live London Underground tracks and working in small restricted spaces. Trains entering and exiting two lines of track at the bridge's north end of track meant that access was difficult due to the location and proximity to existing infrastructure. The site was very much constrained and congested and there were also a series of works in place to maintain passenger flows so as not to inconvenience the travelling public. The site had been developed many times in the past resulting in a number of obstructions that would require removal during the piling work including old brickwork, reinforced concrete, redundant railway sleepers and track and existing concrete and timber piles. A number of solutions had to be devised to overcome these obstructions. Piling works were undertaken during the day and at night to meet programme.

Jan 1, 2011

By Giovanni A. Bonita

The new Embassy of the Peoples Republic of China in the United States (Chinese Embassy) is located in the Embassy Row portion of Northwest Washington DC. The 475,000 ft2 (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. The structure approaches the property line on all sides, and is immediately adjacent to several foreign embassies and a secure U.S. Federal Building. A vertical soil nail wall was used as the primary support of excavation (SOE) system for the project. The soil nail wall was irregularly shaped, benched in areas, and reached total heights up to 98 feet (29.9 m). The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Tight excavation requirements were defined for the project due to the location of the building relative to the property line, requiring fairly precise wall positions and shotcrete tolerances. Design challenges included soft soil conditions, inside wall corners, underground utilities, and seismic impacts from blasting. The paper will focus on the design, construction, and performance of the soil nail SOE system, as well as touch on the logistical and political factors that influenced the design. The paper also notes the Value Engineering and communication approaches that were generated during construction. These efforts resulted in a significant improvement in the quality control and quality assurance exhibited on site, expedited the schedule, and led to significant cost savings to the contractors, engineer, and owner.

Jan 1, 2006

By Alan J. Lutenegger

Some years ago, a method was developed to incorporate a grout column around square-shaft helical screw-piles and anchors to increase shaft buckling resistance under compression loading. An additional benefit of this grouted shaft is to increase the load capacity in both compression and tension, depending on the geometry of the lead helical section and the soil conditions. Because of the unique construction procedure, the contribution of the shaft to the total capacity has largely been unknown. The behavior of grouted shaft helical anchors in clay was investigated by performing full-scale axial uplift (tension) load tests on a series of anchors installed at the University of Massachusetts Geotechnical Test Site. In order to isolate the contribution of the grouted shaft to the total load capacity, anchors were installed with a wooden dowel connection between the lead helical section and extension sections on three of the four anchors so that only the shaft resistance would be measured during the load tests. The grouted shafts ranged in length from 10 to 30 ft (3 to 9 m). Initial tests were performed approximately 5½ months after installation. Nearly four years after the initial tests were performed, the tests were repeated to evaluate any significant change in capacity with time and/or repeat testing (preshearing). The soil conditions at the site are presented along with the load-displacement curves for both the initial and repeat teats and a discussion of the analysis of the results. Repeat load tests showed an increase in capacity from the initial testing, however the percent increase was not the same for all depths. The results demonstrate that considerable shaft resistance can be developed in clays from the grouted shafts as might be expected. Depending on the L/D ratio of the shaft and the contribution of the lead helical section, at working loads the shaft capacity can dominate the behavior.

Jan 1, 2011

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018