Search Documents

By J. M. Mitchell

Kuala Lumpur, Malaysia is underlain by karstic limestone. Firm clays, mudstones and siltstoncs of the Kenny Hill Formation overlie the limestone for about two thirds of the city. The remaining third has deep deposits of very soft alluvium, or tin mining slimes, overlying the limestone. It is only recently that large buildings have been constructed in the area. Arup Jururunding have been concerned with several projects located on the limestone, although space here only permits the description of four sites in detail. The experience has allowed the development of a design approach for the foundations. The aim is to make the architectural scheme compatible with the geology. This is not always possible, and examples are given of both situations. The case histories give examples of compensated foundations, and piled foundations include steel H-piles, precast concrete piles, micropiles, bored piles with rock sockets, and barrettes up to 90m deep.

Jan 1, 2010

By W. J. van Niekerk

Ballast Nedam is in Surinam constructing two bridges that will improve communications in the coastal region. The bridges will cross the Coppenam and Surinam rivers and will be founded on open-ended steel piles over 60 meters in length. The majority of piles are inclined and support prefabricated concrete girders forming the roadway. In most locations the stratum is consolidated cohesive layers extending to a depth in excess of 60 meters. For this reason, before pile driving operations commenced, it was decided that a number of test loads would be carried out determine the capacity of the piles. Loading tests were carried out on specially installed piles as well as on piles that would be used as working piles to support the structure. Working piles were dynamically tested using Pile Driving Analysis (PDA) equipment. This decision was based on the inclination of the piles, the cohesive nature of the soil and the increase of strength after the piles are driven. A good insight has been obtained into the real strength of the soil by comparing dynamic and static loading tests on vertical test piles. This made it possible to determine the required length of pile.

Jan 1, 2000

By Bruno Gemmi

A new warehouse built with prefabricated components over an area underlined by soft marine soil deposits started showing differential settlements well before its completion. Its 103 spread footings carrying up to 4,000kN (450t) axial loads had been cast on jet-grouted columns extending and penetrating a layer of sand at a depth of 10m (33ft). Investigations performed to assess the wholeness and consistency of the jet-grouted columns revealed a state of loose jet-grouted masses and uncontrolled, off target migrations of the jet-grouting. Most of the jet-grouting itself was settling. The following remedial solutions were suggested: 1. Construction of new and better controlled jet-grouted columns. 2. Cement-based soil grouting. 3. Expanding resin injections. 4. Minipiles drilled-through the existing footings and reaching into a denser layer of sand existing at 23m below grade. Remedial solution 1. was immediately discarded due to cost and the possibility of a repeating failure in this non-granular and highly compressible soil. Tests of remedial solutions 2. and 3. were carried out. The outcome of the grouting was monitored by Electro Resistivity Tomography (ERT) (Bares et al., 2003), an innovative 3D electro tomography procedure showing where grout had been actually placed and its migrations off target. A successful 4,000kN (450t) load tests confirmed the validity of the solution. Finally, upon the completion of a successful load test, solution 4. was chosen. It supplied the highest degree of reliability thanks to the ease of controlling the final and actual location of the minipiles and to the higher safety factor provided. All remedial work to install the minipiles was eventually performed inside the building. Additional load tests and settlement measurements confirmed the adequacy and success of the chosen solution.

Jan 1, 2011

By Naresh Koirala

The Greater Vancouver Regional District completed installation of a 2.5 Km long, 2400 mm diameter concrete sewer in Delta, British Columbia in 2000. The sewer traverses through area of peat and soft ground. The ground investigation along the sewer alignment consisted of cone penetration tests and auger drilling with standard penetration tests. The gravity sewer is supported on precast, pretensioned spun concrete piles imported from Malaysia which had never been used for a major project in North America. The capacities of the installed piles were tested using pile driving analyzer (PDA) and three static load tests. A total of 46 PDA tests were carried out during pile installation. The paper describes the pile vetting process the owner went through prior to accepting the piles for use in the project and performance of the piles. It compares the pile capacity estimated from the PDA tests with that estimated from soil mechanics methods using data from cone penetration tests and standard penetration tests. The ranges of estimated capacities calculated by different methods are discussed from design capacity selection considerations.

Jan 1, 2004

By Frank Haehnig, Kjell-Åke Averstad, Johannes Glückert

"AbstractThe Söderströmstunneln is part of the Citybanan project that is currently under construction in the centre of Stockholm. Main part of the lot Söderströmstunneln is a 300m long immersed tunnel connecting the inner-city islands Södermalm and Riddarholmen. It consists of three tunnel elements that have been immersed in summer 2013. Since the solid bedrock is descending in that area to more then 40m depth, the tunnel elements have been placed and are permanently supported on four pile groups that have been constructed in advance. The common Swedish system of steel core piles has been used to built the pile groups. Drilling and installation of the steel cores piles in free water depth of up to 20m had to be done from a pontoon. The steel core piles are connected with underwater concrete pile caps.IntroductionCitybanan is a new 6km long double track railway tunnel running beneath central Stockholm including two new underground stations Odenplan and Stockholm City. When completed in 2017 commuter trains will have their own tracks through Stockholm, whereas the remaining railway traffic will continue to use the exisiting two tracks (see Fig. 1). This will double the capacity of the railway traffic through Stockholm. The Swedish transport administration Trafikverket is the client for this project. The design and built contract is carried out by the German contractor Züblin Spezialtiefbau GmbH together with their Swedish subsidiary Züblin Scandinavia AS.As the new Citybanan tunnel is in large parts situated below the bedrock level, it can be executed as rocktunnel in the common drill and blast method. Between the two inner-city islands Södermalm and Riddarholmen the tunnel is crossing the Söderström, an arm of the lake Mälaren. Here the bedrock is descending to a deep valley with more then 40m depth. To connect the rock tunnels between these islands a 300m long immersed concrete tunnel supported on pile foundations is currently under construction."

Jan 1, 2014

By Harry G. Poulos

Ground movements can arise from a large number of sources and can have a significant effect on nearby piles and deep foundations. The loading of the piles by ground movements is a different mechanism to that arising from direct applied loading to the pile head, and consequently it is not generally possible to adequately analyze the effects of ground movements simply by applying some type of equivalent loading to the pile head. The main effects of ground movements are the development of additional movements, axial forces and bending moments in the piles, and thus the key design aspects are related to movements and to the structural integrity of the pile. However, the ultimate geotechnical load carrying capacity is generally not affected by the ground movements themselves. This paper will describe an approach to the analysis of ground movement effects on piles, considering axial and lateral movements separately. Some of the main features of pile response will be discussed for three specific problems involving ground movements: 1. Piles near and within embankments; 2. Piles near an excavation for a pile cap; 3. Piles subjected to seismic ground motions.

Jan 1, 2007

By Tom Szynakiewicz

Micropiles are routinely used in the United States for foundation support and underpinning applications. The high capacities achievable with the use of micropiles, combined with specialty rigs for easy installation in low headroom and difficult access areas makes them a good choice for situations often encountered on existing commercial projects. The bond zone of the pile is typically drilled into a competent stratum such as sands, gravels or bedrock. In this paper, the authors will discuss a project where the lack of a shallow ?competent stratum? led the geotechnical contractor to create their own bond zone for the micropiles using jet grouting. Due to problematic clay (CH) soils, the original foundation of a six story office building in west Houston had experienced up to five inches of differential movement in-between the shallow under-reamed shafts. The owner desired a permanent solution to the problem without disturbing the majority of the tenants. The structure was underpinned with a hybrid system of jet grouted micropiles as well as jet grouting alone and the structure was re-leveled using hydraulic equipment to within a 0.25? tolerance. Design, construction and sequencing of the project are discussed in the paper. QA/QC methods are also discussed, including coring for verification of jet grout column diameter as well as a full-scale micropile compressive load test. The structure was successfully re-leveled and the entire project was completed without disturbing any tenants on the floors two through six.

Jan 1, 2008

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By Alec C. Bloem

A 55' deep excavation encompassing almost a city block in London, Ontario required a lateral earth retention system to provide both temporary excavation support and a permanent groundwater cut-off wall for a proposed office complex. The system selected was an interlocking Drilled Shaft wall with 3-4 levels of tiebacks. The specifications required the system to be designed for movements or settlements around the excavation of ¼" max. Design to be by the Contractor with design parameters and a comprehensive soils report provided. An extensive system of instrumentation in the form of inclinometers and survey targets were used to monitor vertical and horizontal movements of the shoring system and adjacent properties. Introduction The project, One London Place, is a two phase office tower development in downtown London, Ontario. Phase one consists of a 24 storey office tower on the northwest part of the site, with five levels of below ground parking over the entire site "Figure 1". A second office tower will be constructed at a future date.

Jan 1, 1991

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By R. Heath Forbes

The route of a new, 4-mile long, electrical transmission line passed through residential neighborhoods and commercial areas of a small town in the South Carolina Coastal Plain. The new line consisted of 54 new poles and a one-mile underground section. Most of the new poles were constructed within 50 ft of existing structures, and in some cases, within 8 ft to 20 ft. A widely-space subsurface exploration consisting of 20 cone penetration test soundings indicated the subsurface conditions along the alignment generally consisted of saturated, loose to medium dense, fine slightly silty to silty sand. The pole foundations consisted of 20 to 30 ft long, prefabricated ?caissons? (essentially an open-end pipe pile with a prefabricated connection system at the top) with diameters of 28 to 56 inches. The steel caissons were installed with vibratory pile hammers. To help prevent damage and defend against possible allegations from nearby property owners, vibration and settlement monitoring was performed during all foundation installation activities. Limited structural condition assessments were also performed before and after foundation installation. For 53 of the 54 foundations, the ground vibrations recorded at distances coincident with the nearest structure locations ranged from 0.05 inches per second to 1.46 inches per second. With consideration of the dominant frequency, the majority of these values were below the commonly used USBM vibration limits. For a foundation installation that was only 8 ft from the nearest structure, a peak particle velocity of 3.06 inches per second was recorded, which exceeded the USBM limits. For all cases, the measured ground surface settlement was negligible (i.e., less than ¾ inch). Several spurious claims alleging vibration-induced damage were made, but the monitoring program provided an adequate defense. One claim involving artwork that fell to the floor during foundation installation at a distance of 8 ft from the house was deemed legitimate.

Jan 1, 2011

By Y. Duraisamy

This paper presents the compressibility of tropical peat reinforced with cylindrical cement column. When a cement column installed vertically in peat, its compressibility was reduced because of the hardened skeleton matrix formed by cement particles bonding with adjacent soil particles in the presence of pore water. The effects of diameter, number of columns and cement proportions in cement columns on the compressibility have been investigated in this study. The results indicated that compressibility index Cc and Ca decreased with the increase in diameter of the cement column. Specimens with 45 mm and 60 mm diameter of cement column were cured for 28 days, after which they were subjected to Rowe Cell Consolidation test. Based on the results obtained, it shows that cement columns can successfully reduce the compressibility of tropical peat.

Jan 1, 2007

By Lance A. Roberts

Micropiles are commonly utilized for applications other than foundation retrofit. In bridges, for example, micropiles can serve as the permanent foundation elements or can be used in temporary support applications. In this paper, a case study on the use of micropiles for the 18th Street Expressway Bridge rehabilitation/repair project in Kansas City, Kansas is presented. In the project, micropiles were utilized for support of six temporary jacking structures, which allowed the bridge to be lifted while repairs were completed. A group of six micropiles was required to support each jacking structure. The required compressive service load per micropile was approximately 300 kips (1300 kN) and the settlement of the micropiles under the service load was to be limited to 0.5 in. (12.7 mm). Two field compression tests were conducted as part of the project. The field load test data was integrated within a soil-structure interaction capacity approach in order to analyze and permit the shortening of the design bond length for the production micropiles.

Jan 1, 2009

By Alun J. Davies

This paper describes a design-build project for the construction of a tanker wharf for 150,000 dwt vessels. The tankers deliver oil from offshore oil fields to a Transshipment terminal on the south coast of Newfoundland. The project described is an expansion to a previously constructed facility, adding an additional berth. The first berth was designed conventionally as concrete structures supported on groups of independent, single piles. The second berth was awarded to Peter Kiewit Sons' Co. Ltd. based on an alternate design which utilized a "jacket" concept whereby prefabricated steel frames are placed on the seabed and serve as permanent templates and also give lateral support to the piles, thereby increasing their load capacity. This led to economies and time savings. Discussed herein is the design process and the field installation, covering the jackets, driven pipe piles, and the rock anchors.

Jan 1, 2000

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006

By John E. Lens

How much trouble can narrow vertical fissures in bedrock cause on a shallow bedrock site? Enough trouble so end-bearing H-piles range between 8 and 100 feet long in a single pile cap and tiebacks range from 40 to over 100 feet long within a 10 foot wall span. Sloped bedrock surfaces also complicated the tieback installation as the drill casing followed the sloped rock surface while drilling and caused unanticipated bending (and sometimes breaking) of the drill string. Warned via pre-construction rock probes and cores reaching over 80 feet deep at the Winooski, Vermont project site, the design and construction team expected anomalies in pile driving and tieback drilling due to fissures in the bedrock filled with soil and weathered-rock. The degree of abruptness in the variability in the rock surface, and its impact on pile driving and tieback drilling were less predictable. Close monitoring of pile and tieback installation, redesign of pile caps, and lengthened tiebacks overcame these anomalous fissures. This paper shares the lessons learned for overcoming these geologic challenges to benefit designers, contractors bidding the work, and ultimately, the owner, with lower contingencies.

Jan 1, 2006

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By Rob Jameson

"The demand for commercial and residential construction has continued to evolve across the United States over the last decade. Our markets demand larger, deeper and inherently more complex structures, located within increasingly constrained urban locations and with challenging geotechnical conditions. As project demands incrementally escalate, specialty contractors are continuously challenged to extend their state of practice. Development in the size and capabilities of construction equipment, tooling, techniques, monitoring and verification systems over the last decade has consistently allowed contractors to build larger and deeper. For support of excavation (SOE), in addition to scale, selection of the most appropriate system has been a key to success in the most challenging ground conditions. This selection process is based on sound engineering and construction practice, and also prior experience, both positive and negative. Ultimately many Owners have chosen to manage their risk of SOE construction through design-build contracts, which allows specialty constructors to optimize the balance of cost, schedule, scope and associated risk based on their local expertise. Successful implementation of a design-build methodology begins long before a contractor is selected, with identification of key project requirements and risk factors during the feasibility studies and design development phases. In these early stages of the project development, advice and budgets are frequently solicited from Specialty Contractors. The Owner, Construction Manager and Consulting Team will filter this input from multiple sources to provide their specific recommendations, develop construction documents and select the appropriate form of contracting. Only in the final stages, after award of a Design-Build Subcontract, can the successful specialty contractor directly influence risk management approach on the project. A case study is presented from Block 9 in San Francisco’s Transbay District. This project demonstrates the incremental identification, assignment and mitigation of construction risk through the planning and design build process for SOE on the deepest planned excavation in San Francisco.INTRODUCTIONThe mature urban development market in United States results in high demand for complex Support of Excavation (SOE) schemes on constrained sites. The Design-Build approach can be applied to increasingly difficult SOE challenges, combining regional specialty subcontractor knowledge and experience in order to optimize solutions for cost and schedule. The most successful applications will involve early engagement of shoring subcontractors within the project teams, during feasibility and design development stages, in order to identify key scope and risk issues, and their potential solutions. Throughout the project development, it is important to reasonably assign responsibility for construction risks amongst the project stakeholders who are best able to control them.This paper presents a case history for San Francisco’s Block 9, a well-planned and successfully executed design-build SOE project in San Francisco’s Transbay Redevelopment area. Throughout the 4 year period from the Developers initial proposal to the Redevelopment agency, through completion of excavation down to subgrade, the project team developed a series of increasingly refined SOE schemes, with corresponding scope definition and cost and schedule estimates. This program relied on early identification of key challenges and risks for the project, and evolved through multiple phases of proposals as first the General Contractor (GC) and then Specialty Shoring Subcontractor were engaged for the project. The scheme, cost and schedule refinements continued throughout construction in order to accommodate unanticipated conditions and events as they unfolded."

Jan 1, 2017

By S. Hardy

The paper describes state of the art non-linear analyses of the pile groups that were employed during the raising of the 133m high triumphal arch which forms the centre piece of the new Wembley stadium in North London. The deformation behaviour of these piles groups was critical during the lifting process, due to the slendemess of the arch structure. The issue was made more critical by the high profile nature of the project. The results of Class A (Lambe (1973)) predictions of the pile group movements are compared with observed displacements and rotations which were accurately measured on site. To illustrate the importance of soil non-linearity on pile group behaviour, comparison is also made with pile group analyses which assume a linear soil stiffness.

Jan 1, 2006

By Dan A. Brown

The following paper was written by Dr. Dan A. Brown, P.E. Brown is an Associate Professor at Auburn University's Department of Civil Engineering. The paper was originally presented at a FHWA's Transportation Research Board meeting and is presented here with the author's consent. Construction and design of drilled shaft foundations in hard pinnacle limestone requires flexibility from all parties involved due to the variability of the subsurface conditions. This article describes some strategies which have been found useful in the Birmingham, Alabama area. The importance of well trained and experienced field personnel in these conditions is noted. It is also vital that engineers understand the construction challenges so as to provide both quality assurance and cost effectiveness in design and in the specifications.

Jan 1, 1991