Search Documents

By Charlie Graham, Helen Shang, Ashley Scott, Andrew Hall

"Approaches to Energy Recovery• Upgrading for electricity generation - steam turbines• Direct extraction- process improvement or space heating- support medium for animal or plant growth– fish or microalgae• Heat pumps- space heating/coolingWater Energy Grades• High (150+ °C) - electricity Generation• Medium (26 to 121 °C) - direct extraction• Low (5 to 18 °Celsius)- use of heat pump is required• Temperatures between zones will depend on circumstances for best use."

Jan 1, 2012

By J. F. Liu, L. Chen, C. P. Wang

"Calcite-cemented joints abound in the rock masses of Beishan area, which is the most potential area for the high-level radioactive waste (HLW) disposal of China. The mechanical properties of Beishan granite containing a calcite-cemented joint with a dip angle of 82° was investigated under uniaxial compression and the acoustic emission (AE) characteristics were also studied in this paper. Compared to intact granite, the calcite-cemented joint caused a decrease more than 50% in uniaxial compressive strength and a decrease more than 90% in shear strength. The Young’s modulus was also decreased, while the circumferential deformation of jointed granite was sharply increased. The AE monitoring system successfully recorded the process of micro-crack development and the results indicated that the risk of rock-burst could be reduced due to the appearance of calcite-cemented joint.INTRODUCTIONThe properties of jointed rocks differ considerably from that of intact rock. Due to the difficulties in specimen preparation, analogue experiments with artificially prefabricated fractures are often used to study the mechanical behavior of jointed rock (Chen et al. 2012; Kulatilake et al. 2001; Singh et al. 2001). However, natural joints are not quite similar to the artificial fractures and it is necessary to investigate the mechanical behavior of jointed rocks. Xie et al. 2011 studied the mechanical properties of marbles with natural joints by uniaxial compression tests and found that the uniaxial compressive strength of jointed rock is greatly decreased. With the unaxial compression tests, Jacobsson 2005, 2007 tested the intact and jointed granites, which were taken from the potential site for high-level radioactive waste (HLW) disposal of Sweden. However, no significant difference in strength or modulus was found. The above research results are inconsistent and it indicates the complexity of the mechanical properties of natural joints."

Jan 1, 2015

Experimental determination of the response of an AG/SAG mill treating two components of significantly different impact resistance is challenging for two main reasons: firstly, small scale laboratory tests have yet to be confirmed as valid representations of the full scale milling environment, and secondly pilot plant testing requires 10-20 tonnes of ore per scenario which precludes the use of drill core, rendering the process very expensive. In order to mitigate these difficulties, modelling was considered as a potential way forward. However, as the JKSimMet AG/SAG model currently has no capacity to simulate the interaction of two ore types with differing impact resistance, density and/or feed size distributions, an alternative modelling approach was developed. This approach aims to essentially calibrate the AG/SAG process under a set of given conditions, for which survey data and the ore properties of the main components in the feed blend already exist. This paper describes a new conceptual model, which provides a simplified approach for investigating the multi-component behaviour of two ores of differing hardness/SG in a given AG/SAG milling environment, and which can potentially be used for scale-up from laboratory/pilot testwork and geometallurgical estimation of throughput.

Jan 1, 2012

By Lizelle Glaner

An investigation was carried out by Mintek to investigate the influence of additions of gold to ?Fecraloy?, alloys based on Fe-Cr-Al. The aim was to try and improve the oxidation resistance of the ?Fecraloy? alloys at elevated temperatures over extended periods of time. The ?Fecraloy? alloys are very oxidation resistant alloys already employed in industry as substrates for metallic catalysts in auto-catalyst systems for high performance cars. Since their life and durability is limited by the slow, but steady, oxidation of the substrates, any change in the growth or stability of the oxides could be an improvement.

Oct 1, 2003

By R. B. Fermor

"AbstractAttention is drawn to the ventilation problems arising from the use of diesel vehicles underground, especially in view of the fact that diesel fumes in combination with other pollutants may be more harmful than diesel fumes alone or the other pollutants alone.Means for minimizing the harmful effects of using diesels underground are listed, and the quantities of air' required in mines in which diesel-powered vehicles are used are discussed. Mines are classified in three categories on the basis of severity of ventilation problems, and statistics are given for these categories.Details of the various components contributing to total ventilation needs are given, and the ventilation needs of individual mines in the three categories are listed. A description is given of the principles according to which main ventilation coursing is planned and the selection and siting of main fans is discussed.General Considerations in the Use of Diesel-Engined Vehicles UndergroundIN ORDER to reduce physiological hazards, present and latent, to workers in mines in which extensive use is made of diesel equipment underground, it is important that mine ventilation systems reduce the concentrations of rock dust, diesel fumes and particulate matter as rapidly as possible to an acceptable level in all parts of the mine.There is some evidence that the long-term effects of a combination of the above pollutants are greater than those of anyone of them alone, which makes the problem even more pressing."

Jan 1, 1977

By R. D. Brown

Higher employer costs and increased employee benefits will result from the current sweeping revisions of the un-employment insurance system now receiving consideration before Parliament. The new legislation, the Un-employment Insurance Act, 1971, will substantially increase the unemployment insurance costs of many employers through an increase in the level of employer contributions -generally, employer contributions will go to 1.4 times employee costs -as well as by extending coverage to many classes of employees now exempt. Under the new legislation, executives, technicians, teachers, institutional workers and others will be covered, and eligible for the higher benefits which it provides. For the first time, absence from work because of illness or accident may qualify individuals for unemployment insurance benefits.

Jan 1, 1971

By R. R. Rogers

Introduction The subject of cathodic protection is not new. In 1824 Sir Humphry Davy, in publishing the results of his investigations for the British navy, pointed out that copper could be protected from sea-water corrosion by connecting it electrically with zinc or iron. Since that time much work has been clone in this field, particularly in the protection of metals from the action of sea water, neutral brines, and treated and untreated waters. Special mention should be made of the successful protection of underground pipe-lines which formerly were badly corroded by the water in the ground. So far, magnesium alloy and zinc anodes have been the most popular. However, fairly recent work has indicated that aluminium anodes will give good service under certain conditions. The principle of cathodic protection has been applied extensively in coating steel articles with zinc and in cladding aluminium alloy sheet with pure aluminium. A valuable discussion of the fundamentals and applications of cathodic protection recently was presented in the Corrosion Handbook. A useful list of references was included in the article.

Jan 1, 1949

By D. J. Zuliani

A mass and energy balance for a modern electric arc furnace ("EAF") indicates that about 70% of the process energy losses are contained in the off-gas as chemical energy in the form of uncombusted CO and H2 and as thermal energy. Given the magnitude of the off-gas energy losses, improved EAF energy efficiency needs to focus first on controlling furnace practice to maximize "in-EAF" energy utilization and second, on recovering residual energy in the off-gas existing in the fume system. This paper focuses on the application of off-gas analyzers, sensors and process models to control and optimize "in-EAF" energy utilization efficiency. The paper will also discuss the application of heat recovery technology to EAF steelmaking.

Jan 1, 2015

By P. Fossi

This report describes a pilot-scale study of a hydrometallurgical process to treat high-grade nickel matte or a nickel-cobalt sulphide precipitate to produce high-purity electrolytic nickel. The first step of the process is the oxidative leaching of the nickel-bearing material by nitric acid; the nitrous gases generated during leaching are reconverted to nitric acid. The crude nickel sulphate nitrate solution is purified and is then subjected to a denitrification step. Nitrate separation is effected either by the crystallization of nickel sulphate or by precipitation of basic nickel carbonate. The electrolyte is prepared from the nitrate-free material and nickel is then recovered by electrolysis of the sulphate solution using insoluble anodes. Some technical and economic problems encountered with this processing route are discussed and the method is compared to the "all-chloride" process developed by Société Le Nickel.

Jan 1, 1977

By C. E. Baltzer

This paper highlights the electric power situation in Canada, and introduces brief explanation of the salient differences between electrical practice in the United States and Canada. The availability of bask energy in the two countries is touched on, also the hydro versus thermal outlook as applying to Canada. De-v2lopment of thermal-electric power is dealt with in some detail, followed by Canada's thermal-electric power requirements, present and future. The fuel requirements for steam-electric generating plant are assessed on the basis of a survey recently made, and the location and size of the major thermal plant operations are given. Fuel contractual obligations on the part ?of suppliers and consumers are mentioned. Finally, an opinion is expressed in regard to the types of f.uel in ?demand on a regional basis with emphasis on the need for coal in the several areas dealt with.

Jan 1, 1958

By Anthony A. Zoobkoff

Gotcha! ? What Did I Just Agree To? ? You can?t repeat or use anything you heard. ? Did you agree before you knew what you were going to be given, told or shown? ? If you knew what you were to be given, told or shown, would you have still agreed?

May 1, 2013

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By P. S. Arthur, G. R. F. Alvear

Development of a new smelting process is risky. Many novel processes in the metals industry failed to fulfil the initial expectations of their inventors. Large sums of capital have been invested in technologies that either didn't provide a satisfactory return on investment, or didn't perform at all, and had to be replaced. One of the keys to success in process development is incremental scale up of the technology, with potential problems being identified and rectified as early as possible. In this way the cost of any rectification that is required can be minimized. The ISASMELTTM process was developed to maturity by Mount Isa Mines through the 1980's and 1990's using incremental scale up. Commercialization only occurred once the process had been proven on laboratory, pilot and demonstration scale over many years. As a result ISASMELTTM technology now operates successfully at numerous plants around the world. The methodical approach to development of the technology has allowed owners to modernise their existing operations or create new businesses with significantly reduced technical risk.

Jan 1, 2011

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By R. I. Cavanagh, A J. Last

THE USE of higher grade charges in blast furnaces in the form of sintered or pelletized concentrates has been increasing rapidly. The question of beneficiation of iron ores for this purpose is therefore receiving much attention as more deposits are developed. Many iron ores may respond well to magnetic roasting procedures followed by magnetic concentration, however, in most cases other more standard ore dressing methods are competitive and cheaper. For magnetic roasting as applied to iron ore beneficiation, the present question is "Can it be economically justified in situations where it appears to produce good results?" The following collection of information on the general status and operations of magnetic roasting methods may be helpful in considering this question. Magnetic Roasting Magnetic roasting involves the transformation of non-magnetic iron oxides, hydrated oxides and carbonates by means of heat and suitable

Jan 1, 1961

By S. Noh, T. K. Kim, B. O. Lee

Future nuclear reactor systems such as a sodium-cooled fast reactor are being designed under severe conditions in terms of operating temperature and irradiation fluence compared to current commercial reactors. For realization of such systems, it is necessary to develop an advanced structural material having both high strength and irradiation resistance at high temperatures. Oxide dispersion strengthened (ODS) steel is considered as one of the most promising structural material because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density. Up to now, ODS steels have been intensively studied and developed to apply these materials to the in-core structural component of future nuclear systems. Several advanced ODS steels were designed and fabricated by a mechanical alloying, hot isostatic pressing and hot extrusion processes. This study focuses on the effects of heat treatment parameters during the fabrication process parameters on the microstructures of ODS steels for future nuclear system applications.

Jan 1, 2015

By L. Kraszewski

"IntroductionPortland cement is produced by burning an accurately proportioned mixture (raw feed) of finely ground limestone, silica, alumina, and iron oxide. The kiln discharge (clinker) is a chemically complex mixture of calcium silicates, aluminates and ferrites which when ground and blended with from 2 to 5 percent of calcium sulphate is sold as Portland cement.ManufactureThe most common raw materials are limestone and clay or shale. The raw mix is finely ground and heated to about (2600°F) 1430°C to decompose the calcium carbonate and combine the calcium oxide with silica, alumina and iron to form a partly fused clinker. The clinker is then ground, usually with a small proportion of calcium sulphate (gypsum), which regulates set. Cements with special properties are produced by varying the oxide composition and also by adding small amounts of chemical agents at the clinker-grinding stage or later.Clinker is manufactured by either wet or dry process methods. In the wet process, raw materials are prepared, blended and fed to the kiln as a water slurry (about 30-35% water) . In the dry process, raw materials are prepared, blended and fed to the kiln as a dry powder (about 0.5% water). The processing procedure is as follows:"

Jan 1, 1982

By Charles Goodeve

"BEFORE I begin, I should like to thank The Canadian Institute of Mining and Metallurgy for the honour they have bestowed in inviting me to give this address at the fourth annual C.I.M. Conference of Metallurgists banquet.Secondly, I should like' to convey the greetings of the Iron and Steel Institute of Great Britain in accordance with a request made by its Council at its last meeting. The I.S.I. hopes for the continued growth in strength of this annual Conference and in the collaboration between our respective societies.When I read the program of this Conference, it was brought home to me what a non-ferrons country Canada is. Also, I realized what enormous advances have been, and are being made, and what an ex-citing field non-ferrous metallurgy is for the scientist. This made me wonder, as I have done before, whether the future for steel was proof against these advances.At present, iron and steel stand astride the metallurgical world like a Colossus; I hope that the bronze industry will pardon my stealing their thunder and mixing my metaphors! Will this still be so in the future?The best way to answer this question is to take a look at the fundamentals to see why the iron atom dominates to such an extent that al! other metals are called ""non-ferrons."" Is its present position due to historical and therefore ephemeral reasons, or is there a fundamental difference between the atom of iron and those of other metals?"

Jan 1, 1966

By E. S. Allen, P. R. Kruesi, J. L. Lake

An electrochemical process is described for converting concentrates of base-metal sulphides to the corresponding pure metals and elemental sulphur. The application of the process to chalcopyrite is discussed. The process is also of potential interest in processing copper-nickel sulphides, and laboratory data concerning this potential are presented. The process creates neither air nor water pollution.

Jan 1, 1973

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt's progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008