Search Documents

By H. J. lgner

Hydraulic fills are widely used in the tabular, steeply dipping stopes of the South African gold and platinum mines as an integrated process within a daily cycle of drill and blast. There is therefore only a small time window in which to fill the geotextile bags used as primary fill containment, without the risk of loosing production. Consequently, mines tend to increase the flow rate to the stopes, although this compromises adequate drainage, consolidation and strength development during filling. Recent underground measurements inside the geotextile bag have revealed that at high rates of rise and at 25 degrees dip, the backfill can remobilise within a limited area inside the geotextile bag during filling. This sudden downward surge of backfill exerts, for only a few seconds, additional loading on the geotextile, its supporting mesh and the props. This unstable behaviour poses a serious threat as it can push props out of place, thereby damaging the geotextile bag and causing a mud slide in the stope. To reduce the risk of accidents, the phenomenon of sudden slumping was further investigated for various filling conditions in the laboratory. The results confirmed that the maximum pressures associated with the sudden slumping can be more than five times those experienced during steady-state consolidation. Based on this new insight, the current best practice for hydraulic backfilling was critically reviewed. A practical approach to implementing meaningful standards is presented to ensure safe operations in relation to the consistency of the backfill quality and the appropriate matching of geotextile characteristics with backfill properties.

May 1, 2007

By Robert D. McKellar, Luke Frawley, Okrasa. Richard

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By J. Awmack, M. A. Tomlinson, P. J. Lind

"Peñasquito is a complex polymetallic deposit containing gold, silver, lead, zinc, and copper and is one of the largest producers of gold in Mexico. Mining activity is currently transitioning to a second open pit, Chile Colorado, which will be mined concurrently with the existing open pit, Peñasco. The ore bodies are located within diatreme pipes and into the surrounding sediment formation. In the coming years, mining will be carried out in more sedimentary zones, which are significantly higher in organic carbon content. Organic carbon in the feed influences both flotation and leaching operations. Several changes are being implemented to the Peñasquito flowsheet to mitigate the effects of increased organic carbon in the plant feed. These include the use of alternate reagent schemes, construction of a carbon pre-flotation circuit, implementation of a pre-leach flotation circuit ahead of pyrite leach, and evaluation of a tertiary process for separation of carbon and precious metal minerals.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas in the Mazapil municipality (Figure 1). Peñasquito has been in operation since 2009, with mining carried out by open-pit methods. Oxide ore has been processed in a heap leach facility and sulfide ore is treated in the sulfide processing plant. The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 465,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead in lead concentrate, and 263 million lb of contained zinc in zinc concentrate (Goldcorp Inc., 2017). To recover more of the contained gold and silver and to mitigate the impact of increasing organic carbon content in the ore, a number of significant changes are being made to the operation."

Jan 1, 2018

By M. W. Grabinsky, J. H. Curran

"Characterizing the spatial distribution of rock stresses is a challenge, especially in the geologically complex environments typically found at most metalliferous mines. Therefore, instead of focusing, specifically, on the task of making stress measurements, the engineer should instead attempt to develop a better understanding of the interaction between stress, mining geometry and rock mass behaviour. This paper demonstrates such an approach using a Canadian Shield hardrock mine case study, in which geomechanical models are used to relate stress, mining geometry, and rock mass properties to observed excavation response, and numerical modelling is used to better quantify this interaction.IntroductionUnderstanding how the mine geometry, field stresses and rock mass interact to produce the observed rock mass response to mining can be a significant challenge. Consider our present ability to quantify the basic geomechanical design input data. Mine geometry is normally quantified in more detail than is required for analysis purposes. Our understanding of rock mass strength and stiffness is far from complete, but established procedures do exist to obtain estimates of these parameters based on index and laboratory testing data and field mapping. Our ability to quantify field stresses is probably the most limited, in part because stress measurements are difficult and expensive to carry out, and in part because the stresses vary to an unknown degree from point to point within the rock mass. The engineer must, therefore, consider whether or not stress measurements are justified and, when they are, where the average stress state needs to be quantified and how many of which type of measurements will be required to determine the average stresses.Such was the case at Ansil mine, a massive sulphide deposit in hard rock located at a depth of more than one kilometre in the northern Québec portion of the Canadian Shield. The Ansil orebody was relatively rich, but small, with the potential for significant stress-related problems. As a result, geomechanical design had to be done carefully from the start – there would be little opportunity to modify the mining strategy once production had begun, and the economic consequences of stope dilution and rock mass instability would be severe. An extensive stress measurement campaign was carried out, but the determined stress magnitudes were unexpectedly low. The designers were, therefore, faced with a dilemma:"

Jan 1, 1997

By Leroy C. Stewart

Owing mainly to the use of ethylene dibromide in the production of tetraethyl lead for gasoline treatment, there has been a tremendous increase during the past decade in the demand for bromine. In the United States, production, derived mainly as a by-product from the treatment of brines from salt wells, rose steadily from about two million pounds in 1924 to nine million pounds in 1931. In 1936, production amounted to between 20 and 21 million pounds. Much of the increase during the past four or five years has been due to the operation of the Ethyl-Dow Chemical Company's plant, which extracts bromine directly from sea water. The process employed by the Ethyl-Dow Company is somewhat similar to that in use on salt-well brines at their plant at Midland, Michigan, but whereas these brines contain around 1,300 parts per million bromine, sea water contains only 65 to 70 p.p.m.-about as much as the waste effluent in the brine process. By intensive research, however, a process was developed whereby a very considerable percentage of the bromine content of sea water could be recovered, and at a satisfactory operating cost. In its essentials, the process consists in liberating the bromine from the sea water by treat-ment with chlorine, blowing the bromine out of the water by a current of air, and finally absorbing it in a solution of soda-ash.

Jan 1, 1938

By T. Marolt, J. Likar, E. Grøv, J. Žarn

"Underground structures are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, not at least nuclear facilities. When the wider area is subject to earthquake activity, underground constructions should be analyzed on seismic and static loading. Observations showed that the underground structures have significantly less seismic risk than surface structures. Available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. Simulation of earthquake loading on underground structures, in the present paper is given the various aspects of analyzing the potential damage and instability of underground facilities. INTRODUCTIONThe development of methods and computing resources used for para-seismic engineering has finetuned the evaluation of the seismic strength of buildings and equipment. Reinforcements may therefore be decided, not simply on the basis of a reassessment of the hazard, which constitutes input data for the calculation of structures and equipment, but also on the basis of developments in para-seismic engineering. Underground facilities are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, material storage, and sewage and water transport and not at least nuclear facilities. Although in the past showed that the underground structures are significantly less seismic risk than on the surface, the professional researches and their results are accessible. Seismic resistance of underground structures is analyzed from several aspects. The currently available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. For better interpretation of earthquake loading on underground structures, are given below the various aspects of analyzing the potential damage and instability of underground facilities in rock. One of the early studies which covered this are of investigation were prepared by Dowding and Rozen (1978). They grouped damages due to earthquakes in underground structures into three main categories:- damage from ground shaking- damage from fault dislocation- damage by earthquake-induced ground failures (e.g. liquefaction and landslides)."

Jan 1, 2015

By E. L. Martheleur

Introduction In October, 1945, the Coal Division of the Institute appointed a Committee on The Use of Electricity in Coal Mines, with the following terms of reference: ?To study under which conditions in each deposit the use of electricity can be brought closer to the coal face and which types of electrical machinery can be recommended?. It was not until the beginning of this year (1946) that the Committee had a chance to convene and .discuss the conclusions which are embodied in this report. Mr. McLeod, as Chief Electrician of the Dominion Coal Company, is intimately concerned with that Company's installations, and Mr. McIsaac, as Electrical Inspector of Coal Mines for Nova Scotia, is well acquainted with installations in all coal mines in the Province. The knowledge of both has been very valuable in helping to draft this report.

Jan 1, 1946

By R. B. Nourse, S. F. Gwynn-Jones, S. Nikolic, M. L. Bakker, I. McDougall, H. Joubert

"Tenova Pyromet’s core furnace knowhow and expertise has been built within the ferroalloy and nickel/platinum group metal (PGM) industries with the supply of electric furnaces for a number of nickel/PGM operators, including Eastplats, Lonmin, and Anglo-Platinum in South Africa, Mineraçào Serra Da Fortaleza in Brazil, and Norilsk Nickel in Russia. Tenova Pyromet has also supplied the electrode columns and associated electrode equipment – the heart of the electric furnace technology – for cobalt recovery in furnaces in Zambia and the Democratic Republic of the Congo. The quantity and size of projects undertaken by Tenova Pyromet has provided the opportunity to continuously improve furnace designs and the scope of supply, culminating in the most recent nickel/PGM project currently under construction at Northam Platinum. Through this innovative culture, the Tenova Pyromet Base Metals Initiative was formed in 2015 to develop the Novasmelt™ Furnace; a next generation optimised Top Submerged Lance (TSL) furnace design. The combination of Tenova Pyromet’s advanced Novasmelt™ product with our industry leading electric furnace technology are discussed with reference to applications for nickel and cobalt production. Flowsheet arrangements are compared summarising potential capital savings, operating requirements and achievement of downstream product quality.INTRODUCTION Tenova Pyromet is a leading player in the field of smelting technology development and equipment supply. Tenova Pyromet is the result of the union of three furnace suppliers under the Tenova banner: Techint Technologies (Tagliaferri), Core Furnace Systems Corp (Lectromelt) and Pyromet Technologies. The furnace experience of the combined groups dates back over a century with the earliest Lectromelt going into production in the early 1900s. Throughout the modern era, Tenova Pyromet has developed a reputation for providing dependable innovative smelting technology, high quality equipment and sound project execution to a worldwide client base with customer plants operating in Europe, Southern Africa, North America, South America, Russia, Kazakhstan, the Middle East, South Korea, and India. Tenova Pyromet’s core knowledge and expertise was developed in the South African ferroalloy, base metals, and platinum group metals (PGM) smelting industries. Tenova Pyromet has spent considerable effort on development and has contributed significantly to improve the state of the smelting industry. Tenova Pyromet’s electrode columns have become widely renowned and are now providing significant benefits, especially in increased furnace availability, to many smelting furnace operators. The electrode column is the heart of the furnace as it delivers a controlled amount of electrical energy, at an optimum depth in the burden/bath, to the smelting process. Every furnace is custom designed to the specific operating range and optimal operating point of that furnace and process"

Jan 1, 2017

By Barry Hope, Javier Rico

"Goldcorp’s Hoyle Pond mine has recently completed several projects which have impacted the overall ventilation system. The project includes extending the Fresh Air Raise (FAR) to depth, development of a new Return Air Raise (RAR), and the installation of new sensors and ventilation controls throughout the mine. Two years after the completion of #2 Winze, the mine is ramping up its ore production to 1,300 tpd (up from 1,100). To ensure safe and profitable production, a reliance upon technology has been needed to provide the required ventilation to the work areas according to the mine plan. To systematically assess the mine’s ventilation in real-time, a significant increase in remote monitoring was required. This included installing additional flow, pressure, temperature and gas sensors. The first step in upgrading the existing monitoring was to purchase airflow and differential pressure monitors and install them in key areas of the mine. This paper presents the process of expanding the monitoring capability at Hoyle Pond mine, the selected equipment and the results of the implementation. The intended goal was to improve safety while minimizing capital and operation costs. The monitors were installed in strategic locations to provide immediate feedback on the impact of changes to the primary ventilation airflows. Comparing the available sensor technologies, installing them and systematically monitoring the ventilation served as a first step towards developing a mine wide Ventilation Control System. In addition, the initial state of the monitoring and control system, with final results and the chosen solution for the mine site, are presented. INTRODUCTION The Hoyle Pond mine is located in the City of Timmins, within the Porcupine mining district, Ontario, which has produced more than 70 million ounces of gold since 1910. Currently, approximately 60% of Porcupine Gold Mines gold production comes from the Hoyle Pond underground mine. Mechanized cut and fill and long-hole mining methods are used to extract the ore. The remainder of the ore comes from the Hollinger Open Pit mine. The Dome Underground mine ceased operations in 2017. Hoyle Pond is currently mining at 1820 meters below the surface and plans to go deeper. The average dry-bulb as wet-bulb temperature underground varies according to the depth and surface conditions which has extremes of –40°C in winter to +30°C in summer. The total airflow volume pushed down from surface is 240 m3/s to accommodate the diesel-powered equipment needed for normal operations. In order to improve the quality of air underground a program has been implemented to use diesel particulate filters, starting with the truck fleet and 6-yard scoops, followed by the intention to implement the rest of the functional diesel-powered equipment and eventually move to electric equipment."

Jan 1, 2019

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale simulation method has been developed to study the material scratching processes on nanoscale single crystals. The model simultaneously captures the atomistic mechanisms near the free surface and the long range mobility of dislocations and their interactions, without the computational cost of full atomistic simulations. The method also permits the simulation of system sizes that are approaching experimentally accessible systems, albeit in 2D. Simulations are performed on single crystal aluminum to study the atomistic details, surface evolution, and generation and propagation of dislocations for a variety of scratching depths at room temperature. Simulations demonstrate the power of the developed method in capturing both long-range dislocation plasticity and short-range atomistic phenomena during tool advance. Variations of scratching normal and tangential forces are investigated and related to plastic deformation and dislocations generation during the simulation process.

Jan 1, 2006

By David G. Meadows

During the last decade Antofagasta Minerals? Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.

Jan 1, 2012

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited available technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "observational construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of a mountain tunnel (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert et al. requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electro-optical distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily management measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this proposed method. It then presents the typical results of a field demonstration test at a tunnel under construction. Lastly, the predictable range from the stratum boundary at which ground stiffness changes are discussed based on the results of three-dimensional numerical analysis.

Jan 1, 2015

By CIM Mineral Resource, Mineral Reserve Committee

Industrial minerals are generally considered to include non-metallic minerals, mineral products, or materials that provide raw material inputs for the construction, chemical, and manufacturing industries. They are often relatively low-value and bulky materials that are generally used close to where they are produced; however, some raw materials may be transported hundreds of kilometres to manufacturers and customers (ENDM, 2021). They do not include the metallic minerals, mineral fuels, or gemstones, and are used in industries based on their physical and/or chemical properties (Wikipedia, 2021). In contrast to most metallic minerals, a general distinguishing characteristic of the industrial minerals sector is their general low degree of market elasticity in relation to the market prices and product specifications. The estimation of either a Mineral Resource or a Mineral Reserve (MRMR) for an industrial minerals deposit can be affected to a significant degree by a number of factors that are not typically applicable to metallic mineral deposits. These factors can include such considerations as the particular physical and chemical characteristics of the final product, product quality issues, market size and market access. In some cases, such information may be confidential and proprietary. One of the key challenges of the industrial minerals sector is to define a commonly accepted listing of which types of minerals, materials, or mineral deposits can be considered as industrial minerals (Mining Standards Task Force, 1999). Although definitions for what constitutes an industrial mineral can vary in detail, general descriptions can be found in American Geosciences Institute (2021), Fastmarkets IM (2021), Snowden (2019), SME (2021) and Wikipedia (2021). A brief listing of some of the materials and minerals that are generally considered to be industrial minerals is provided in Table 1. For the purposes of this document, all references to industrial minerals include not only the minerals, materials, and mineral deposits themselves, but also the various commercial products that are derived from these sources.

Nov 19, 2023

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By David Ulrich Furrer

Materials and manufacturing processing technologies have played an important role in the development and capabilities of nearly all manmade products. Market drivers for fuel efficient, low cost, environmentally friendly, more capable transportation has given rise to significant materials challenges and subsequent developments. The rate of improvement and implementation of new commercial products can be limited by the rate of new materials and process technology development and qualification. As many materials are being designed for unique requirements and even location-specific unique properties, the implementation of tools and methods to enable rapid characterization and validation of material definitions and design systems must also be accelerated. A review of new integrated material, manufacturing process and component designs, engineering processes and emerging tools and methods will be discussed. The linkage of computational materials science and engineering into component design will also be discussed along with the challenges and opportunities for further growth and application of integrated computational materials engineering (ICME).

Jan 1, 2015

By Ryan L. Veenstra

This paper presents a modelling study of a cemented paste backfill in an underground stope. The model was developed to help provide a better understanding of what is happening in the stope during the filling stage of the stope. In order to do this, the model incorporates the paste rise rate, stope geometry, and time-dependent input parameters. This paper looks at the effect of geometry in two parts. The first part compares a series of simple rectangular stope models. These models differ in size both in two and three dimensions. The second part compares the results of four 2D models together and then to the field instrumentation data. Part of this section introduces the geometry and instrumentation within the test stope.

Jun 1, 2012

By Henry Lepp

Introduction A shaft sinking operation carried out at the Viking Yellowknife mine in the spring of 1947 presents certain features, especially as regards speed of sinking and low cost, that may be of interest to Institute members, and especially to those who are not familiar with conditions and costs in the Northwest Territories. After collaring, the inclined, two-compartment shaft was sunk 130 feet by four miners in twenty-eight days at a direct cost of only $53.19 per foot. All things considered, this is a remarkable performance, even if it does not actually establish a record. The property is at Morris lake, some forty-five miles north of Yellowknife. Formerly owned by Athona Mines (1937), Limited, it was acquired by the then newly incorporated Viking Yellowknife Gold Mines, Limited, in 1947. Surface work and diamond drilling in 1946 disclosed a number of veins and masses of quartz in a sill of diorite which lies conformably within sedimentary rocks. The sill strikes N.30°E. and dips at 70° to 85° southeast, and has a mean width of 40 feet over its explored length of 3,000 feet . Both the quartz and the diorite carry gold and are mineralized with pyrrhotite and lesser amounts of galena, sphalerite, chalcopyrite, and arsenopyrite. Of thirty-five holes drilled in the mineralized zone, the core from twenty showed visible gold. Sampling of drill cores indicated several ore shoots in the north and central parts of the sill. Assays, however, were somewhat erratic, possibly due to the fairly widespread presence of visible gold, and it was decided that the deposit could best be explored by underground sampling. Accordingly, late in 1946, plans were laid for the sinking of a shaft.

Jan 1, 1948

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

By L Gill

The four basic types of electric motors -squirrel-cage, wound rotor, synchronous and D.C. -are de-scribed, with particular reference to speed-torque characteristics. The three classifications of squirrel-cage motors, C.E.M.A. B, C and D, are compared, and methods of selection for specific drives are outlined. Wound rotor and synchronous motors are covered from the viewpoint of construction details, methods of operation and control required. The application of these motors to crushers, conveyors and ball mills is described and reasons for their selection are given. The application of D.C. motors to haulage equipment and mine hoist drives is included, and the basic principles of a variable voltage drive are illustrated. Efforts have been made through-out to provide specific examples of motor selection, with particular reference to the mining industry. THIS paper will attempt to answer the question -"which motor should be used for a specific drive?" Although it is impossible to cover the complete subject of electric motor application here, we hope to give some idea of the types of motors available and why certain types are used on specific applications.

Jan 1, 1963