Search Documents

By Yongteng Dong, John P. Quinn, Bradford Wesstrom, Guikuan Yue

With increasingly low-grade copper ores being mined, it is difficult to handle growing concentrations of As, Sb, Bi and/or Fe in the whole flowsheet, especially during copper electrorefining. To better elucidate the effects of those impurities on the quality of cathode deposit and/or current efficiency, a detailed speciation study of the electrolyte under industrial conditions is required to quantitatively describe their distribution in the solution, thereby facilitating their effective control and removal. In the present study, a thermodynamic model of complicated iron-arsenic-copper-sulfuric acid electrolyte under industrial conditions was developed. The main species of those elements involved in the electrolyte were first identified, and their thermodynamic data were collected and critically assessed. Those data were then used to estimate the activity coefficients of species, and to calculate the equilibrium constants from 25°C to 70°C. The developed model provides a mathematical tool that is capable of quantifying the concentrations of free ions and complexes in terms of temperature and solution composition. Finally, oxidation-reduction potential measurements were employed to validate the model. INTRODUCTION In copper electrorefining, impurities like arsenic, antimony, bismuth and/or iron can partially dissolve in the electrolyte and accumulate gradually, and eventually cause problems such as bad cathode deposit (co-deposition with copper or mechanical inclusion from the floating slime), lower current efficiency, etc., which eventually increases the operating costs. The presence of impurities may substantially reduce properties of copper products such as conductivity, corrosion resistance, mechanical properties, and leads to more energy consumption (Schlesinger et al., 2011; Jafari et al., 2017). To remove these impurities, various methods have already been proposed and applied in industrial copper production, such as solvent extraction, ion exchange, chemical precipitation, absorption by activated carbon, etc. (Cunningham et al., 1997; Navarro et al., 1999; Toyabe et al., 1987). In addition, adding reducing agents such as sulfur dioxide and trivalent arsenic could also precipitate arsenic, antimony and bismuth from copper electrolyte, by changing the distribution of impurities with various valence (Braun et al., 1976; Xiao et al., 2007). The disadvantages of those methods include high energy consumption, serious contamination, lower selectivity and efficiency, and so on.

Jan 1, 2019

By G. Chahal, L. C. So, S. Faucher, S. Mostaghel, S. -Y. Oh, S. K. Lee

Slag dumping and water granulation are the most commonly used slag treatment methods in the metallurgical industries. In both processes, water is present (by desire for cooling and dispersion or as a result of rain accumulation) and thus equipment and operations are designed to minimize and mitigate the risk of steam explosions resulting from the inappropriate contact of slag with water. Slag handling practices have, therefore, never been inherently safe; even good design, operation, and maintenance are not sufficient to prevent explosions or other related injuries from occurring. For slag handling to become inherently safe, our industry must eliminate the potential contact of water with molten slag. This is today feasible with the advent of dry granulation technologies, a review of which is presented, and it thus falls to us, in the metallurgical sector, to lead the way in their final stages of development and adoption. Furthermore, while slag dumping and water granulation offer some metallurgists the means of valorizing their slag as a by-product, for most, this is not the case. The energy in slag is lost through dumping and water granulation processes, and where slag is sold as a by-product, it is for its chemical content only. Here, dry granulation processes also offer advantages including the production of by-products which hold value in both their chemical content and physical properties and heat recovery. Dry granulation, therefore, augments the methods by which slag may be valorized over traditional processing methods.

Jan 1, 2015

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019

By George Carico

Research and related demonstration projects are being conducted in West Virginia on both existing and former coal surface mine lands to determine potential post-mine land re-use options that offer the greatest likelihood of future benefit and success. Examples of projects include renewable energy considerations that incorporate solar, wind, and/or biomass options, and contain components designed to educate business, government entities and the local community on renewable energy options and potential opportunities Multiple property re-use options are being researched and evaluated, based on site-specific conditions and characteristics, including infrastructure, local community needs and regional economic conditions. Re-use options being explored include innovative uses and needs, such as specialty housing, unique business and industrial needs, and an extensive variety of recreational and small business opportunities that best fit the specific needs of the local community and regional economic structure.

Aug 1, 2013

By S. M. Bradshaw, E. Charikinya

"Microwave induced cracks have the potential to enhance metal recovery from coarse sphalerite particles in heap leaching operations by creating new crack surface areas for lixiviant and enhancing value mineral exposure. The mode of fracture and the extent of mineral exposure due to microwave induced cracks have not yet been investigated. The objective of this study was to determine the extent of particle damage and mineral exposure in microwave treated particles. This was done using X-ray computed tomography (XCT) and image analysis techniques. XCT analysis was conducted on small (–5+4.75 mm), medium (–16+9.5 mm), and large (–25+19 mm) sphalerite ore particles before and after microwave treatment (MT). Geometrical properties, such as volume and surface area of each mineral phase in each particle was determined from the XCT reconstructed images using VGStudioMax image analysis software. These geometrical properties were used to calculate the interfacial areas of sulphide mineral grains in microwave treated particles before and after MT. The ratio of specific interfacial area after MT to specific interfacial area before treatment was used as an indicator of the degree of preferential grain boundary fracture. The results showed significant grain boundary fracture after MT at all sizes. For small sized particles, about 31% of the interfacial area was lost compared to 23 and 16% for medium and large particles, respectively. The results also showed an increase in the degree of mineral grain exposure of 28, 26, and 15% for small, medium, and large particles, respectively, after MT. These results provide experimental evidence supporting improved mineral exposure due to MT. INTRODUCTIONFor some years it has been suggested that microwave treatment (MT) of ores might result in preferential grain boundary fracture that would have benefits such as improved grain exposure and particle weakening. (Kingman, 2006). Most of the experimental work investigating the application of microwaves to mineral processing flow sheets has focused on assessing the benefits of applying microwave technology to flow sheets consisting of size reduction and mechanical flotation cells (Kingman et al., 2004). Experimental studies have shown that coarse crushing during tertiary grinding of microwave treated ore resulted in a better liberated coarser flotation feed (Scott, Bradshaw, & Eksteen, 2008). It has been suggested that improved liberation in milled flotation feed, was due to the presence of grain boundary fracture in microwave treated particles. However, this improvement in coarse particle liberation does not necessarily translate to a significant improvement in downstream flotation recovery (Kobusheshe, 2010). This is as a result of the size limit to the flotation of coarse material, due to detachment forces acting on particle-bubble aggregates, which increase as the particle size increases (Jameson, 2012). Current conventional, mechanically agitated flotation cells are not designed to float coarse material (Jameson, 2012). Hence it has been difficult to show the downstream processing benefits of applying microwaves to ores processed by comminution followed by flotation (Kobusheshe, 2010). It is clear from investigations carried out so far that inappropriate downstream exploitation of microwave treated ore would fail to realise a meaningful process benefit (Kobusheshe, 2010; Ali & Bradshaw, 2011)."

Jan 1, 2016

By H. Houali

Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items: ? Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists; ? Range of protection (potential of protection along the pipeline); ? Influence of the isolation resistance of the coating on the range of protection; Effect of the aging of the coating and its influence on the current of protection

Jan 1, 2005

Forward-Looking Statements Information set forth in this presentation may involve forward-looking statements under applicable securities laws. Forward looking statements are statements that relate to future, not past, events. In this context, forward-looking statements often address expected future business and financial performance, and often contain words such as "anticipate", "believe", "plan", "estimate", "expect", and "intend", statements that an action or event "may", "might", "could", "should", or "will" be taken or occur, or other similar expressions. Forward-looking statements or information relate to, among other things expected iron ore demand, timing for a production decision, expected share price drivers, potential railway options, timing, grade and quantity of potential resource estimates, employment and economic benefits, taxation estimates and timing of key project milestones. By their nature, forward-looking statements involve known and unknown risks, uncertainties and other factors which may cause our actual results, performance or achievements, or other future events, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. Such factors include, among others, the following risks: the risks associated with the need for additional financing; operational risks associated with exploration; fluctuations in commodity prices; title matters; environmental liability claims and insurance; reliance on key personnel and other risks and uncertainties discussed in the management discussion and analysis section of our interim and most recent annual financial statement or other reports and filings with the TSX Venture Exchange and applicable Canadian securities regulations. Forward-looking statements are made based on management's beliefs, estimates and opinions on the date that statements are made and the Company undertakes no obligation to update forward-looking statements if these beliefs, estimates and opinions or other circumstances should change, except as required by law. Investors are cautioned against attributing undue certainty to forward-looking statements. NI 43-101 Qualified Person Alderon?s exploration work on the Kami Project is supervised by Edward Lyons, P.Geo., the Chief Geologist for Alderon and a Qualified Person as defined byNational Instrument 43-101. Mr. Lyons has reviewed and is responsible for the technical information contained in this presentation. Mr. Lyons is a member in good standing of the Association of Professional Engineers and Geoscientists of British Columbia (APEGBC) and the Professional Engineers & Geoscientists Newfoundland & Labrador (PEGNL) as a registered Professional Geoscientist (P.Geo.).

May 1, 2011

By William Skinner, Jim Pae Lem, Massimiano Zanin

It is well known that the specific density of minerals has adverse influence on the classification performance of a hydrocyclone, particularly when liberated high density minerals such as gold or uranium are present in sulphide ores. These liberated heavy minerals often misreport to the underflow and recirculate to the system. Such phenomena does result in serious issues in a closed-grinding circuit, such as overgrinding, leading to production of flaky particles (as in gold) or ultrafines, in addition to increased energy inefficiency. In plants which present gold liberated at coarser size, loss of gold due to cyclone inefficiency is sometimes prevented by incorporating gravity concentrators into the grinding circuit to recover the gold. The work reported in this paper looks at whether the effect of density will prevent successful rejection of liberated U-bearing minerals in the –10µm size range of a plant re-cleaner feed, which is necessary to minimize penalty U accumulation in a copper concentrator. The study was carried out using a cyclone rig with spigot diameter of 0.25 inches in combination with batch flotation. It was found that the density effect is almost negligible at particle sizes below 10µm. Consequently, the liberated U-bearing particles finer than 10 µm were successfully removed in the overflow stream as rejects and hence U grade in the copper concentrate remarkably reduced, by 16 ppm. Based on the results, de-sliming of the re-cleaner feed was recommended for plant trial and implementation.

Jan 1, 2016

By M. Sanchez

In the last decades, the Chilean copper mining and metallurgical industry have had to modify their technological processes to meet the environmental regulations implemented by the Chilean government, and also to support the pressure of the public opinion. Thus, air quality standards for sulfur dioxide and particulate matter (primary and secondary), plans for reducing emission of arsenic by the Chilean copper smelters, effluents discharge limits, among others regulations were applied by the environmental agency. Additionally, agreements on cleaner production were carried out by mining sector and government. Now, a draft law on mine closure, and another on environmental mining wastes (abandoned mines) are being discussed by the authorities and the mining sector. In the context, production and environmental impacts in different ways to produce copper in the Chilean mining industry are reviewed and regulatory tendencies as well as abatement technologies today used are exposed and discussed in this presentation. Pyro, hydro and electrometallurgical processes employed and their current effluent and contaminants are presented showing various alternatives of treatment in the copper industry. An update of regulations established in Chile vis a vis copper production, with an especial attention to mine closure are also presented.

Jan 1, 2007

By Y. Masuda, Y. Nakamura, K. Haraguchi, A. Taniguchi, K. Arita

Availability of the elements originating from steelmaking slag for various marine phytoplankters including purely cultured strains and natural populations was tested in land and shipboard laboratories. The results obtained demonstrate that, although their solubility was not uniform among different slags, dissolved iron, silicate and phosphate from the slag stimulate phytoplankton growth. No negative effect of the slag addition on their growth was observed at lower dose, e.g. less than 200 mg/l. Since most coastal waters are the hypernitrogenous environment due to anthropogenic load of ammonium, the slag can be an ideal source of silicate and phosphate, which restore the hyper-nitrogenous condition into truly eutrophic condition with balanced Redfield ratio. In so-called HNLC (high-nitrate low-chlorophyll) oceanic areas such as the Southern Ocean and the subarctic North Pacific, where iron is almost only limiting factor of the phytoplankton growth, the slag could also be a source of iron and enhance CO2 fixation by phytoplankton photosynthesis. (Key words: carbon deposition in deep-sea, marine environmental remediation, phytoplankton, slag as a source of iron, phosphate and silicate.)

Jan 1, 2004

By Rainer Süss

An investigation was carried out by Mintek to investigate the influence of a range of alloying additions (vanadium, cobalt, zirconium, antimony and germanium) on the formability and hardenability of alloys with gold content >90 wt%. This paper reports on the hardening mechanisms that can be utilised to increase the hardness of gold (>90 wt% Au) by conventional alloying, as well as the hardening effect obtained by alloying with specific elements. Preparation methods for the alloys are described, which include the steps of melting, annealing, quenching, cold working and age hardening. Focus is given specifically on alloys that were developed at Mintek with a gold content >90 wt%, which are not only harder, but exhibit good resistance to tarnishing and corrosion.

Oct 1, 2003

By H. R. Manouchehri

"It is well understood that, apart from particle hydrophobicity, the flotation process is strongly influenced by the cell hydrodynamics. Once the chemical conditions were optimized and fixed, the flotation rate is essentially determined by impeller speed and the air flow rate.The collection efficiency in flotation is a product of collision, attachment and stability/detachment efficiencies. The collision efficiency for a given particle diameter is increased by decreasing the bubble size and bubble velocity as well as increasing the power input to the cell. The attachment efficiency, however, is defined by bubble size and its velocity. The detachment/stability depends on the relative magnitudes of the attachment force between the bubble and particles and the detachment force acting on the bubble-particle aggregates. For the particles having specific contact angle, the stability decreases as the energy input increases. Therefore, there must be an optimum energy dissipation to maximize recover of defined size fraction.A comprehensive laboratory study was devoted to determine the effect of power input in recovery of finely grind Cu-Ni bearing ore. Several flotation tests were conducted to define the hydrodynamic parameters for a laboratory scale Runge cell under different impeller speeds. An increase in flotation recovery of finely ground ore was observed when the impeller speed was increased from 450 to 1,200 rpm. The experimental results have shown increasing in water recovery and improving in flotation kinetics of fines by increasing the power input to the flotation cell. Implementation of the Wark flotation model to the experimental data revealed a good correlation between the experimental data and the model. For the particles having enough hydrophobicity the flotation rate increases by increasing the impeller speed due to a higher value for collision efficiency within the cell."

Jan 1, 2016

By Michael Klichowicz, Holger Lieberwirth

"For a detailed prognosis of mineral comminution processes, simulation tools like DEM still pose various challenges. Less realistic mineral structures can affect the results of simulation models such as bonded-particle models (BPM). Hence, in order to design mineral processes with these models as tools, representative mineral input data should be used. The article shows, how realistic 2D-structures can be modelled by taking advantage of the parameters identified by the Quantitative Mineralogical Analysis (QMA). Important quantitative parameters can be derived by analyzing three orthogonal thin or polished sections. For this reason point, line, and area analysis are applied. The mentioned parameters precisely describe the texture and structure of minerals. The newly developed software is able for the first time to semi-automatically analyze images of mineral structures using QMA. Moreover, statistically equivalent structures of minerals can be modelled using the QMA- parameters. Generating synthetic, but equivalent mineral structures opens the door for more reliable BPM based simulations. Within future research, the procedure will be adopted to generate 3D-structures. Therefore, QMA-based routines that already have been applied to generate 2D-models shall be utilized as basis. The aim of this procedure is to synthesize realistic microstructures based on certain statistical figures in order to improve comminution simulations.INTRODUCTION Due to its increasing capability, the use of computer technology is permanently intensifying in the design of mineral processes. The recent past has impressively shown that computer models can enhance the understanding of mineral processing. There is in fact a rising number of research activities, which are using simulation approaches to study various aspects of it. Weerasekara et al. (2013) give a comprehensive overview over the application of discrete element modelling (DEM) in the science of comminution.Nonetheless, using simulation tools such as DEM in general still poses a challenge. For a detailed simulation of a mineral comminution process with DEM, bonded particle models (BPM) appeared suitable in the past. The following issues, however, affect an appropriate prediction when modelling with BPM:• Simulations with high numbers of particles may need a lot of time for computation. • Internal modeling parameters like the spring and damper constants in DEM have to be adjusted by comparing its specific crushing behavior in the simulation to reality.• In order to use DEM for prediction of mineral processing, it is essential to validate the correctness of the models and assumptions, which is sometimes difficult. As Weerasekara et al. (2013) have stated it is crucial that the DEM method as well as the DEM code work properly.• It is challenging to implement the complex geometric structures of real minerals into the model."

Jan 1, 2016

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By S. Heusermann, S. Fahland, J. Behlau, A. Schäfers, J. Hammer

In the course of the deep subsurface use, the Federal Institute for Geosciences and Natural Resources has been carrying out extensive geological and geomechanical research and practical project work on domal salt structures, to prove their suitability e.g. for the disposal of radioactive wastes. Recent work on disposal sites has been taking into account the 3-D geological and geomechanical modelling of the underground structures. The geological models are generated using the special-construction openGEOTM code to improve the visualisation and interpretation of the geological data basis, e.g. borehole, mine, and geophysical data. For the geomechanical analysis of underground structures the JIFE finite-element tool has being developed to analyze large 3-D structures and to consider coupled THMC processes. The results of finite-element calculations, i.e. stresses, strains, displacements, and dilatant zones, are basic values for the evaluation of the stability of the structures and the long-term integrity of the geological barrier. As an example, the results of geological and geomechanical investigations of the Morsleben repository are presented including three-dimensional modelling of the entire geological structure of the central part of the mine as well as three-dimensional geomechanical model calculations to provide the necessary results for a long-term safety prediction.

Jan 1, 2015

By T. E. W. Nind

"A short description of the chamber lift method for producing oil wells is followed by some comments on compressor requirements and gas utilization. A quantitative analysis of the process is presented and, based on this analysis, criteria are suggested for selecting wells for which this type of lift might be suitable. The analysis leads to the conclusions that chamber lift is an efficient producing mechanism for wells having very low productivity indices (say about 0.05 bbl/d/ p.s.i. or less), but that for such wells optimum utilization of injection gas cannot be attained. It is suggested that the gas injection time per cycle should be kept as low as possible, compatible with a small oil fallback volume, and that the cycle frequency should be in the range of 20-40 cycles/ day. For wells with productivity indices of 0.2 bbl/d/p.s.i. or higher, chamber lift is relatively inefficient; how-ever, if well allowables are low it may offer an attractive, low cost, alternative to gas lift or pumping."

Jan 1, 1960

By The Honourable George Prudham

"I AM PLEASED indeed to be present with you here today and to be taking part in the proceedings of your convention. You have been greeted and welcomed to the Province by Premier Manning who is also provincial Minister of Mines and Minerals, and to this City by Mayor Hawrelak. As Minister of Mines and Technical Surveys in the federal government and as Member of Parliament for Edmonton West, I have been asked to share the honour of extending greetings and a cordial welcome to all.It is a happy coincidence that this representative national gathering, indicative of the growing strength and significance of a great basic Canadian industry, is taking place in the Macdonald Hotel, the new addition of which marks another important step forward in the progress of this City and district.This happens to be the third national convention of the C.I.M. that I •have had the pleasure of attending and I trust that I am not presumptuous in expressing the hope that I will have the opportunity of attending many more conventions of the Institute in my present capacity.Dr. Kidd has bestowed on me a high honour by asking me to be Co-Chairman of this Inaugural Session of the Convention and thus to share with him the responsibility of presiding over the proceedings of this afternoon."

Jan 1, 1953

By G. Capobianco

"The coal industry is an important part of Canada's economy - as an energy source, employer, and generator of export earnings. Coal comprises 71% of our fossil energy and with rapidly advancing handling and burning technology will clearly play a major role in our national energy mix, eventually as synthetic gases and liquids.International coal markets are very competitive and Canada is disadvantaged by long rail hauls to port, and a heavy tax burden. However, high mine productivity has allowed us to increase our markets.Currently, domestic markets are dominated by coal use for electrical generation, a market with significant growth opportunities.Strong growth is expected in export thermal markets, while metallurgical coal demand is projected to show little or no growth in the medium term. IntroductionThe coal industry is a vital part of the Canadian energy scene .• Coal supplies 17% of Canada's energy.• On a per capita basis, Albertans use more energy in the form of coal than they do oil and gas.• The value of Canada's exports of coal last year was equal in value to all the cars we imported from Japan.• Coal is our largest single export to our seco nd largest trading partner, Japan.• The value of coal produced in Canada exceeds the value of any other single mineral produced in thi s country.• In Alberta, the safety record for coal mines is on a par with that of department store clerks.• The coal industry employs about 25% of the total number of people employed in all metal mines in Canada, directly and indirectly accounting for about 50 000 jobs.Coal comprises 71% of Canada' s hydrocarbon energy resources on a crude oil equivalent basis . This is more than double our oil sands resource and dwarfs our conventional crude oil and gas resources (Fig. I). In the short term, coal as a solid fuel plays a significant part in the Canadian energy scene. In the longer term, coal, in the form of electricity and eventually liquids and gases, has a tremendous role to play. In 1986, Canada produced 57.8 million tonnes, slightly down from the record high of 60.8 million tonnes in 1985. Our exports in 1986 were 26.0 million tonnes, a growth of 53% in three years."

Jan 1, 1988

By Ron Tessier, Claude Bazin, Robert Grant, Mike Cooper

"Grinding simulators are now widely available to assist in the optimization of industrial circuits. They provide circuit operating conditions or flowsheet designs that yield a given product size distribution. However, they do not provide information of the impact of a change of product size distribution on the subsequent flotation or leaching stages. This paper presents a method to predict grade and recovery indices for a flotation plant as a function of the flotation feed size distribution. The application of the method to various size distributions allows the determination of the optimal fineness of grind. A case study for a CuPb rougher circuit of a New Brunswick complex sulphide processing plant is presented to illustrate the method.IntroductionIs the grinding circuit product fineness optimum for the subsequent separation steps? This is a question that is certainly very difficult, but critical, to answer. Laboratory and pilot plant testworks can provide clues as to whether grind should be finer or coarser. For a full scale operation there is no other way than trying to change the setup of the grinding circuit and verify the effect on flotation. True effects can, however, be masked by the numerous and unexpected disturbances inherent to grinding and flotation circuit operations. A good preliminary investigation requires a noise free environment to elaborate possible solutions for the question.Plant simulators provide this noise free environment. However, despite grinding and flotation simulators having evolved significantly for the last 20 years, very little is available on the integration of both simulators to analyze the effect of fineness of grind on metallurgical performances. For instance, a grinding circuit simulator may help to find the tuning of a grinding circuit that will yield the desired fineness of grind, but does not inform on the effect the new product size distribution will have on the separation stages. Linking grinding and flotation would require a flotation plant simulator with the rate and infinite recovery parameters for each mineral in each size interval considered. This approach is seldom used because of the tedious work required to estimate the model parameters. Recently Leroux(1992) proposed a method to predict mineral liberation from grinding ore of known mineralogical texture. Although the method is still at its infancy it may provide, when combined with a reagent conditioning model (e.g Niemi et al., 1982; Bazin et al., 1988), a way to simulate flotation without the need of entering the numerous parameters of a flotation model."

Jan 1, 1994

By Thomas J. Ferree

"IntroductionThe objective of this chapter is to provide important criteria relating to the operation and maintenance of spiral concentrators and Reichert cones, so that optimum performance can be achieved and maintained in a mill circuit. Little space will be devoted to the theory of the forces of separation or the technical details of the devices, as that in(ormation is available from other sources. The discussions in this chapter will be presented in a manner that should be interesting and useful to anyone who may be exposed to these methods of gravity separation. It is most important for the reader to understand that each application of the equipment should be considered on its own merit, as no two suites of minerals respond exactly alike in mineral processing circuits. The information herein should be useful as a guide toward increasing the metallurgical efficiency of the processes, irrespective of the type of minerals being concentrated.It is highly recommended that certain tools be made available to the personnel responsible for metallurgical performance of the spirals and cones; these include a set of standard type laboratory screens, a medium quality petrographic microscope, and a vanning plaque or gold pan. These devices, when used in conjunction with a basic understanding of the mill circuit, provide immediate knowledge on the characteristics of any sample in the mill circuit. The information gained by visual evaluation of sized fractions of products can solve many of the basic problems of mineral beneficiation, and at the same time increase the interest of the non-technical personnel associated with the plant operation. There are many problems associated with obtaining satisfactory performance from a mill operation. Many of the problems have to be solved using a technical approach. Some of the problems, however, can be solved with practical knowledge and common sense. It is hoped this chapter can provide a guide to both techniques."

Jan 1, 1989