Search Documents

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By A. Dave Mackintosh

Historical closure data has provided a description of the stress distribution patterns occurring around mine openings and enabled the development of a time ? distance plot predicting the location of the stress peak and its migration away from mine openings with time. Data collected from active mining areas during the 1970?s and 1980?s indicated the peak appeared to stabilize approximately 135m (450 ft.) from openings after four years. The region of high load and accompanying poor ground conditions in which the peak was centred was spread over approximately 45m (150 ft.) to 60m (200 ft.). Recent data from new development headings cut adjacent to 25 year old extraction areas suggests load transfer takes place over a much greater distance and time frame than predicted.

May 1, 2001

By J. Peterson

A review of blast designs and improved blasting practices at the Ekati??Diamond Mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine's well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. Ekati??uses 270mm holes for production blasting, and 165mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion / ANFO blends. The mine plan involves using 30m double benches. A 30m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15m benches. This paper summarizes the monitoring equipment and data gathered to date.

May 1, 2001

By A. A. Sirkeci, M. Tarkan, N. Acarkan, O. Kangal, G. Bulut

This investigation deals with the evaluation of the tailings of the Kirka Borax Plants. In this respect boron in the tailings was recovered and the utilization of the clayish fraction was investigated. There are five tailings ponds in Kirka four of which are used for the tailings of the borax concentrator and the remaining one is used for the tailings of the sodium penta-borax plant. Experiments were conducted with samples taken from ponds containing coarse fraction and fine fraction. Coarse fraction of Borax Concentrator were screened through a set of sieves. The fraction above 1 mm was removed with 41.5% recovery and 33.3% B203 content. Scrubbing was applied above 0.1 mm and products containing 32 to 34% B203 were obtained with recoveries around 35%. The tailings of sodium penta borax plant was also screened and it was found that 15% of boron reported to +1 mm size fraction with 35% B203 content. Sample containing fine tailings was treated by cycloning. The cyclone overflow was found to be below 6µm and it was separated to be used in the subsequent tests. The usage of cyclone overflow in paper, ceramics, glass, pigment and drilling industries was investigated. Since this fraction is mainly composed of carbonate minerals rather than clay minerals it was suggested that it may be used for construction and moulding purposes. Furthermore, the B203 content of the cyclone overflow was reduced to 2.4%.

Jan 1, 2004

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By Richard R. Walker, John J. Watkins, Allen C. Amos, Matulich. Angelo

THE KIDD CREEK MINE is located within the Abitibi greenstone belt, near its west end, in an area known as the Porcupine mining camp (Fig. 5). The Abitibi belt, long known for its many major gold and base metal deposits, is the largest Archean (early Precambrian) greenstone belt within the Canadian Shield. In the Porcupine area, the greenstone belt is composed principally of Keewatin (older Archean) basic to intermediate volcanics, with subordinate felsic volcanics developed• locally. Greywacke, mainly of volcanic derivation, occurs associated with and overlying these volcanics. Timiskaming (younger Archean) sediments, principally coarse clastics, unconformably overlie the Keewatin volcanics and sediments. The reader is referred to Goodwin and Ridler (1970) •r. for a more comprehensive description of the Abitibi belt.

Jan 1, 1974

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

By M. A. Bérubé

Le but principal de cette étude était de vérifier certaines hypothèses de nature minéralogique susceptibles d&apos;expliquer en tout ou en partie les variations importantes observées au concentrateur no 1 de Mines Gaspé quant aux performances du circuit B de broyage et de flottation. A cette fin, nous avons examiné six séries d&apos;échantillons prélevés lors d&apos;une campagne de mesures effectuée au cours de l&apos;été 1980. Ainsi, la capacité du circuit de broyage semble dépendre principalement devariation s dans les caractéristiques minéralogiqu es et texturales du minerai, par exemple du rapport grenat/quartz, le grenat ayant une influence néfaste sur le rendement de cette étape, contrairement au quartz . Quant au processus de concentration, la fraction du cuivre sous f orme de minéraux difficilement récupérés par flottation, en particulier des carbonates de cuivre, varie de façon significative dans le minerai, et cela peut certes expliquer en partie des récupérations parfois plus basses. Malgré ces variations important es de la composition minéralogique globale du minerai et de sa broyabilité, le degréde libération des sulfures de cuivre dans le produit de broyage dépend presque seulement de la granulométrie de ce produit. Afin de garantir des performances égales à l&apos;étape de concentration, il est fortement suggéré de contrôler cette granulométrie à un niveau constant.

Jan 1, 1984

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

By D. A. Pirttinen

The promotion of improved coal quality for thermal generation can benefit our national economy. The construction of electric generating facilities in Canada is expanding at a rapid rate to satisfy the demands of a rising population and new uses for electrical energy. With remaining economic water power resources in the process of development, generation from thermal sources continues to grow. The increase in thermal capability has been somewhat arrested by a de-pressed economy, widening of inter-provincial and state transmission networks and decisions to exploit certain water resources before high capital investment is further in-creased by rising construction costs. The introduction of extra high volt-age transmission lines will further delay thermal generation planning, but in due course, when the effects of restrictive factors have been dissipated, steam-electric generation from fossil fuels will rise to considerable proportions. In time, nuclear sources will contribute a growing share to thermal power, but, it is doubtful if nuclear participation will ever displace conventional fuels for steam rising, unless it can be adapted to operate efficiently for variable outputs in peaking service. It appears certain that fossil fueled

Jan 1, 1961

By P. H. Tolcher

Canada, as the Free World's largest mine producer of zinc and the third largest mine producer of lead, has a vital interest in the future growth in demand for these metals. This paper traces the development of lead and zinc consumption in the last two decades, both on a total-Free-World basis and by major market areas. How Canada, as a major mine producer, has shared in this growth is also indicated. In addition, future consumption for both metals in the current decade of the 1970's is fore-cast. The demand these projections will make on Free World mines, particularly on Canadian mines, is examined. Some of the opportunities and challenges the Canadian mining industry will likely face during this period are also dealt with.

Jan 1, 1971

By C. A. Y. Shephard, H. L. Brusset

Pressure maintenance by water flooding in the Pembina Field made consideration of wet crude dehydration and disposal of the produced water mandatory. Crude dehydration, the treatment and disposal of produced water, as well as the sale of gas and crude oil were expected to be handled more efficiently at one central point than at several conventional batteries. This plan was effected by routing the produced fluids to the central station by way of several well testing batteries referred to as satellites. To realize the full efficiency inherent in such consolidation the entire system was made self-regulating. Programming ensures the testing and proper routing of all products to their destination. Forty producing wells have been self-operated during the winter 1959 -1960 with gratifying results.

Jan 1, 1960

By Frank Otten, Jochen Greinacher

"In July 2017, Deilmann-Haniel signed a contract with IOO Slavkaliy to sink two 750 metre (m) deep freeze shafts for the Nezhinsky Potash mine in Belarus. This is the second shaft project where this technology is employed after two over 1,000 m deep shafts for a potash project in Saskatchewan, Canada, have been sunk by the application of the Herrenknecht Shaft Boring Roadheader (SBR) technology. Developed to sink shafts for green field projects in soft to medium hard rock, in frozen or unfrozen geology, the machine technology utilizes a roadheader-type cutterhead on a telescopic boom to mechanically excavate the rock, and a pneumatic mucking system to convey the muck from the face into the buckets. This leads to a manless face during the sinking cycle and thus a significant improvement in terms of workplace safety. For the Nezhinsky project, the SBR design was significantly modified in close cooperation between Deilmann-Haniel and Herrenknecht, based on the available experience and the special requirements of the project. Such modifications have been for example the adaptation of the Pneumatic Mucking System to cope with wet material as well as dry as originally planned or the shaft lining moving from shotcrete application to jump for and tubbing installation for which a step-change hands-off tubbing erector for the placement of segments was designed. Further modifications to optimize the machine technology for the requirements during shaft sinking were applied on the two machines for the Slavkaliy project as well as several revisions to match the special project requirements. The SBR is suitable for soft and medium hard rock up to 100 MPa UCS. The main design limits are maximum weight of the machine with 400 tonnes and length or height of 50 m due to the depth of the pre-sink. The Pneumatic Mucking System was changed in all components, sheaves and rope arrangement were redesigned and the concept of the hoist system was also re-engineered. The SBR in Belarus is configured for a daily sinking rate of three metres and all systems behind the cutting boom are not the bottle neck of the whole system. The works on site started in November 2017 including freeze hole drilling, construction works, site setup, installation of hoists winches, permanent headgears and other components required for sinking. The SBRs arrived on site in June/July 2018 and were preassembled on surface and then lowered into the 50 m pre-sink. SBR #1 started full face sinking in mid-December 2018, and SBR #2 in late January 2019. By the end of February 2019, the machines were at 150 m and 100 m depth respectively, and achieved up to 3.6 m/day concrete lined shaft. The SBR and the sinking system, the experiences, problems, technical solutions and performances of this challenging project will be presented in this paper."

Jan 1, 2019

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By W. E. Roscoe

The probability of making an exploration discovery in Canada can be calculated from Derry's (1970) data on exploration expenditures and number of discoveries over the last nineteen years. Considering an average exploration "try" to be $30,000, the probability of a discovery with one try has decreased tenfold from about 0.01 in 1951 to 0.001 in 1969. A plot of these probabilities can be extrapolated to the future, giving a 1969-71 three-year average probability of 0.00096 with 90 per cent confidence limits of 0.00042 and 0.00153. Using this probability, various calculations can be made, such as (1) the probability of making at least one discovery for any given exploration expenditure, (2) the probability of ultimate ruin or survival of the exploration investment process and (3) the expected value of an exploration investment. There is a critical minimum amount per discovery that must be re-invested in exploration, no matter how large the original investment is, for exploration to survive at all in the long run. Currently, this critical minimum is $31,200,000 with 90 per cent confidence limits of $19,600,000 and $71,400,000.

Jan 1, 1971

By Patricia Dillon

EHS Management Standards Communication and Reporting (8) ! Establish processes for internal and external communications ! Designate responsibilities for communication with COI ! Report as defined by senior management ! Report annually to employees, shareholders, COI on EHS and social performance Community Rights and Public Consultation (9) !Identify COI?s and establish process to hear concerns !Acknowledge and respond to complaints !Support local communities !Plan for closure and conduct public consultation !New projects include identification of COI?s, concerns to be considered in design

May 1, 2004

By Stanley Davidson

"The ore deposit mined by Falconbridge Nickel Mines, Limited, is one of the numerous nickel-copper sulphide bodies marginal to the large oystershaped mass of differentiated norite in the Sudbury district, famous as the world's most important nickel producing field. The unique character of the ore deposits of the district has resulted in its intensive geological study over a period of more than 50 years. The results of these studies have given rise to a voluminous geological literature and to a great deal of controversy as to the genesis of the ores. This description of the structural geology at the Falconbridge mine is presented in the hope that it may form a small part of the chain of evidence leading to a reasonably satisfactory explanation of the ore genesis.The mine, named after Falconbridge township in which the deposit occurs, lies along the southeast margin of the norite mass, which, however, is h::re concealed beneath a deep mantle of glacial sands and gravels averaging over 100 feet in thickness. As a consequence, the deposit was not discovered by the early prospectors, and it was not until 1916-17 that E. J. Longyear, of Minneapolis, located the ore by drilling(ll). The discovery was foreshadowed in 1899 by the work of Thomas A. Edison, who found indications of the deposit by what is believed to have been a combination of magnetic and electrical geophysical surveys. He sank a prospect shaft over what has to date proved to be the largest and richest ore section in the mine. A wet quicksand layer at the rock surface proved impenetrable, however, and the 'Edison' shaft never reached bed-rock.The Falconbridge property was acquired by the Lindsley interests in 1928, and ore output, since its inception in 1929, has gradually risen from a modest beginning to the present 2,000 tons and more daily. Total production in this period is 7,500,000 tons of ore averaging 1.72 per cent nickel and 0.89 per cent copper, together with a small but valuable content of precious metals, principally of the platinum group."

Jan 1, 1954

By D. J. MacKinnon, Kazi E. Haque

Ammonia present in a variety of mine/mill waste waters was almost completely oxidized to nitrogen by chloride mediated electro-oxidation. A closed circuit operation of preconcentration of ammonia on a suitable adsorbent (e.g. zeolite or a resin) followed by brine stripping of ammonia and electrolysis of the strip liquor seems to have sound technical, economic and environmental merits. The removal of ammonia, cyanide, cyanate or thiocyanate from a mine/mill waste water (e.g. gold mill), either individually or collectively, is also feasible by chloride mediated electro-oxidation technique. Further R&D investigations are necessary for the development of a closed circuit operation for the removal of ammonia, cyanide and thiocyanate; and also to obtain technical data for process cost estimates

Jan 1, 1996

By Z. D. Hora

has been no commercial production of either perlite or pumice in British Columbia. Several promising occurrences are known to exist but their development has been delayed due to difficult access and / or remote locations. The Empire Valley perlite deposit is located 120 km east of Clinton. The deposit appears to be a flat-lying volcanic flow 50 to 70 m thick that is part of an Eocene rhyolite and dacite volcanic assemblage. The Francois Lake perlite deposit occurs on the north shore of Francois Lake where perlite is part of a rhyolitic volcanic sequence. The exposure of perlite is about 13 m thick and is considered to be Eocene or Oligocene in age. The Uncha Lake perlite deposit is located about 5 km south Industrial Minerals in Canada of Uncha Lake. Perlite appears to be intercalated with porphyritic rhyolite flows that are comparable to those at Francois Lake. Showings are widespread but poorly exposed and thicknesses are unknown. The Mount Meager pumice deposit is located in the Lillooet River valley at the base of Plinth Mountain. Coarse pumice agglomerate forms a large talus slope that is undercut by the river. Unsorted, angular fragments up to 50 cm in diameter are intermixed with up to 30 per cent of sand and silt-sized particles. The exposed zone is about 200 m long and 50 m high; it is being considered as a source of lightweight aggregate.

Jan 1, 1984