Search Documents

By S. E. Malouf, W. Thorpe

"The Chibougamau Explorers property comprises 35 claims or 1,726 acres in La Dauversiere and Rohault Townships along the west shore of Norhart Lake. The property is serviced by a twelve-mile all-weather high-way leaving the main St. Felicien-Chibougamau highway at mileage 121. This road junction will be a railway siding on the C.N.R. St. Felicien-Chibougamau branch line in early 1957. The property lies 30 miles due south from the town of Chibougamau. The mine-sponsored Chibougamau Explorers town has a population of 250 with 28 residences and a well equipped recreation centre.The original showing was found by Rider Storn, a prospector financed by Val d'Or interests during the 1950 field season. This showing did not stand up to detailed prospecting but it did lead to the discovery of the main zone by A. Oakley during the following winter.The company was incorporated in I 950 under the presidency of E. Ayrhart. Financing following the initial drilling involved an increase of capitalization from 3 to 5 million shares and the advent of financing and management control by Anacon Lead Mines Limited.Exploration and development to Jan. I, 1956, has included 42,331 feet of surface diamond drilling; 31,363 feet of underground drilling; a 3-compartment shaft to 1,245 feet, with 8 levels at 150-foot intervals; and I 1,054 feet of drifts, crosscuts, and raises. Ore reserves to the 900-foot level, proven and partly developed, total 546,725 tons averaging 0·30 ounces gold and 0·93 per cent copper. A mill with capacity of 500 to 750 tons will be installed by January 1956.GeologyThe Chibougamau Explorers property lies along the belt of Keewatin volcanics striking through Bachelor Lake, Opawica Lake, Doda Lake, Coapatina, Norhart Lake, and Rohault Lake, where it is in close proximity to the paragneisses of the Grenville series. The boundary of the paragneisses, a gradational contact, lies within a mile of the Chibougamau Explorers shaft collar."

Jan 1, 1949

By M. Pelser, H. Gous, J. H. W. M. Brits, K. Voogt

The effect of impurities; iron and selenium, on current efficiency and deposit quality in copper electrowinning was investigated using an at-line cell at the Rustenburg Base Metals Refiners’ Copper Tankhouse. The tankhouse is a direct leach, starter sheet electrowinning operation with a unique electrolyte composition. The effect of iron on the current efficiency in the at-line cell was found to be less severe than reported in literature. However, the distinction between the chemical impact of iron on current efficiency and the physical impact of iron on a starter sheet operation needs to be realised. The effect of selenium on current efficiency and deposit quality is also reported. INTRODUCTION Anglo American Platinum’s Rustenburg Base Metals Refiners’ (RBMR) Copper Tankhouse serves a unique function in the refinery flowsheet in that its primary functions are the removal of copper and production of acid for the leach circuit. This function needs to be performed to specification in order to keep the leach circuit operating optimally. Current efficiency is seen as an indicator of tankhouse performance and efficient energy use. The tankhouse plates starter sheets onto titanium blanks which, after stripping and preparation, return into the production cells for further plating. Approximately 78% of tankhouses surveyed (Robinson et al., 2013) use permanent cathode technology whereas older, smaller operations still use starter sheet technology. Drawbacks of the starter sheet technology are that the starters are thin and bend easily leading to increased shorts, they need to be removed after two days of plating to be manually straightened and are then returned to the cells. In addition, the electrolyte levels in the cells need to be adjusted during the plating cycle to improve loop adhesion to the cathode and reduce loop corrosion. The starter sheet technology is therefore very labour intensive and the final quality of the product is dependent on the quality of the starter sheets produced. In comparison, permanent cathode or direct plating technology lends itself to automation, allows for higher current densities and better cathode quality due to more robust geometric stability in the cell. The present barrier to implementation of permanent cathode plating at the RBMR Copper Tankhouse is the capital cost required to convert the tankhouse, i.e. blanks and stripping machine. At present, alternatives to titanium blanks, such as LDX 2101, are being investigated for the unique electrolyte composition of this tankhouse.

Jan 1, 2019

By A. H. Lang

"The name Barkc:rville district is applied loosely to the gold-bearing area around the historic town of Barkerville; the first mining camp in western Canada. The region is partly in the Cariboo mining division and partly in the Quesnel mining division. It contains two producing lode gold mines; the Cariboo Gold Quartz and the Island Mountain; and numerous other deposits. The regional structural pattern is outlined in this paper; the structural details of the producing mines are described in the papers that follow.The discovery of rich placer deposits in this district in 1860 was followed by the Cariboo gold rush. Placer mining in the area flourished until 1875 and then declined as the shallow diggings were exhausted, but important operations are still active. The total placer production amounts to about $50,000,000. An extraordinary number of quartz veins outcrop in the district, but many have only a small gold content. The miners soon recognized that the placer gold must have been derived from the erosion of these veins, and some directed their attention to the possibility of quartz mining. The erection of a 4stamp mill in 1876 was the first attempt at ore reduction in British Columbia, exclusive of arrastras. Efforts to mine the Cariboo lodes on a large scale were not successful, however, until 1933, when, due to the pertinacity of F. M. Wells and to the increased price of gold, the Cariboo Gold Quartz mine commenced production, followed by the Island Mountain mine in 1934. This success led to development work at many properties in the district, but the only ones that have reached production to date are the Columbia Tungstens, where scheelite has been mined intermittently since 1937, and the Cariboo Hudson, from which gold was produced in 1938 and 1939."

Jan 1, 1954

By Christiaan Zeilstra, Jan van der Stel, Koen Meijer, Gerard Louwerse, Tim Peeters

The steel industry is producing about 5% of the world wide CO2 emission. Therefore the European steel industry has defined a research program to reduce the CO2 emission by 50% per ton: ULCOS. Since its start in 2004 ULCOS has identified four technologies for further development. Two of these technologies which produce liquid hot metal are discussed. The ULCOS blast furnace is based on recycling of decarbonated topgas and the capture and storage of CO2. The concept has been demonstrated during three campaigns at LKAB EBF in Luleå, Sweden. The smelting reduction process HIsarna is a combination of the cyclone-technology and Hismelt. The process has been demonstrated successfully in four campaigns at a pilot installation on the IJmuiden steelmaking site.

Jan 1, 2015

By Ramesh Subramanian

Overview Background / History Undergraduate Programs Mining Engineering Chemical Engineering Mechanical Engineering Graduate Programs and Research Student Enrolment (2002 -) Future Plans

Oct 1, 2010

By A. S. Robb

SAMPLING of an ore-body is one of the fundamentals in its exploration, development, and exploitation. It is carried out to determine the gold value per ton of an ore-shoot and the probable gold output of the refinery. Sampling also places any broken ground in one of two classes, ore or waste. The value and importance of correct sampling has been shown repeatedly in the past. On the other hand, instances could be given where those in charge of mines have not believed in sampling, and the result has been the same in every case-disaster. This has in all probability been due to assuming that good-looking, well-mineralized rock was ore. Sampling in some form might have averted this misfortune. In this essay, only the method of sampling and the estimation of ore reserves is treated. All titles, figures, and values are fictitious. None of the illustrations can be directly applied to any portion of the Hollinger mine, except Figures 1 and 2, which are included with the special permission of the Canadian Mining Journal. METHODS OF SAMPLING Hollinger Consolidated Gold Mines, Limited, has, from the very beginning of operations, carried out an extensive system of sampling, and the results of this sampling have completely governed the whole mining programme. The Hollinger discovery was made in 1909 and prospecting and exploration of 'the surface began at once. Four men were given jobs as samplers and they sampled thoroughly all the outcrops and all bed-rock which could be exposed to view by removing the overburden. When shaft sinking began, samples were taken at two-foot intervals. In 1912, an underground gang of six samplers was organized, and the number was increased at a rate of about two men per year as the size and extent of the workings grew. No permanent record of sampling was kept until 1919, in which year an average of 11.6 men took 28,458 samples, cutting 113,894 feet of sample. From that time until the end of 1934, the average number of samplers varied, but the total number of samples cut, and the total footage sampled, increased.

Jan 1, 1937

By R. D. Brown

In the spring of 1977, Revenue Canada announced its intention to proceed in 1978 with a plan to impute a taxable benefit on interest-free and low-interest loans provided to employees. Such loan arrangements are often an important aspect of the compensation packages provided by many companies to their employees. Since the original announcement, there have been many submissions to Revenue Canada opposing this change, and the Finance Minister has now brought down a compromise solution with the introduction of a proposed amendment to the Income Tax Act. The amendment, which would not take effect until the 1979 taxation year, would require an employee, a shareholder or a related person to include a benefit in income measured as the difference between the interest on any such loan computed at bank prime rate and any interest actually paid. Only the amount of such a benefit in excess of $500 in a particular year would be required to be included in income. Of particular interest is the exclusion from these benefit rules of loans up to $50,000 in respect of the purchase of a house on the relocation of an employee and loans provided for the purchase of shares of an employer corporation.

Jan 1, 1978

By Phillip Mackey, Elmira Moosavi-Khoonsari

L'industrie du cuivre traverse une période passionnante, marquée par une forte demande, de bons prix et l'ouverture de nouvelles grandes installations. L'année 2022 a battu des records de production de cuivre, ce qui laisse entrevoir un potentiel de croissance supplémentaire. De grands projets sont en cours, comme la technologie Double Flash à Manyar, en Indonésie, qui peut produire plus de 500 000 tonnes de cuivre par an. À Munda, en Inde, on a construit la plus grande usine de cuivre du monde, qui produit plus de 1 000 000 tonnes de cuivre par an en combinant deux phases. De plus, l’installation de cellules de flottation de dernière génération au Mexique, au Chili et dans d'autres pays témoignent de la volonté de l'entreprise d'utiliser les technologies les plus récentes [1]. L'importance du cuivre dans la transition énergétique est évidente, l'accent étant mis à la fois sur la croissance et sur la protection de l'environnement. Cela se traduit par le développement d'usines de premier ordre dédiées aux pratiques durables.

May 2, 2024

By J. E. Gill

THE 1938 season was marked by a distinct lull in exploratory activity in the Province of Quebec. Quebec was not unique in this respect, but the condition appears to have been more acute here than in most other parts of the Dominion. Various causes may be suggested to account for this. The general disturbance in political and economic conditions throughout the world has certainly had an adverse influence. Uncertainty induced by changes in the mining laws of Quebec in 1937 contributed. A third cause was the belief, now held by many, that the easily accessible deposits in the main producing belt extending eastward from. the Rouyn district have now all been found and that new discoveries in this field will henceforth come more slowly and more expensively. A fourth is the lack of conspicuous success by companies and individuals who have interested themselves in less accessible areas to the north, notably the Chibougamau district. A fifth, the unattractive appearance, as viewed on published geological maps, of the vast area extending northward to Ungava bay and Hudson strait. A sixth, the attraction of such speculative funds as were available to the Northwest Territories, where spectacular finds were reported in the fall of 1937. Whatever may be the relative importance of these causes, languor in exploration will ultimately be reflected in production returns. This appears, therefore, to be an opportune time to take stock of the general position of the Industry in the Province and to consider ways and means of counter-acting those conditions which are now impeding, or will in the near future impede, its expansion. At the request of the Institute Secretary, Mr. Carlyle, I have prepared a brief summary of accomplishments to date and a discussion of some of the geological aspects of the problem.

Jan 1, 1939

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By J. R. Smith

"The Lake Dufault orebodies were discovered by deep surface diamond drilling. When a reasonable amount of outline drilling had been completed, the decision to go into production was made. The fact that shaft sinking, lateral development, the detailing of the orebodies and stope preparation were to be carried out as rapidly as possible necessitated very close scheduling.After a study of varions possible mining methods, an open-stoping system using long-hole blasting was chosen. Diesel-powered Transloaders were selected for the mucking and transportation of ore from the drawpoints to the orepass.At the time of writing, the choice of mining method appears to have been fully justified, although more time will be required to arrive at true operating costs and efficiencies."

Jan 1, 1966

By S. Kodama, G. Sasaki, K. Matsugi, K. Sugio, Y. B. Choi

"Pure aluminum (Al) matrix composites with changing the volume fraction of TiB2 particle content from 10 to 30% was fabricated by spark plasma sintering (SPS) process. Then the microstructure, density, dispersibility and thermal conductivity of the composites was estimated. As increasing TiB2 content, the dispersibility of particles and the density of the composites degraded slightly. And, the effect of the dispersibility of TiB2 particles on the thermal conductivity was quite little. The thermal conductivity of the composites was less than the theoretical value calculated by Maxwell-Eucken equation considering the effect of the density. It is due the influence of the interface heat transfer rate, because these composites have many small sized particles and have high interface density.INTRODUCTION Recently, metal matrix composites (MMCs) have been used widely in electric / electronic components, architectural materials, transportation equipment, aerospace and a precision instruments, because it’s superior properties have been greatly watched. Demand of MMC for industrial use has been increasing gradually. Furthermore, multifunction properties are required for the composites strongly. By integrating the dissimilar materials, the composites have various properties that we cannot get from monolithic materials. On the other hand, the response to the thermal management is required for materials, recently, and the need for the structural material controlling the thermal conductivity has been increasing. Especially, superior thermal conductivity and good mechanical properties from room temperature to high temperature are required for heat sink and heat exchanger at the same time. In late years, a study on the composites combining carbon materials and aluminum and copper has been developing, and actually the composites with high thermal conductivity which is not provided in the conventional materials is developed. On the other hand, non-oxide ceramics particles such as SiC and AlN, TiB2 have good thermal conductivity. Particularly, as TiB2 has good electrical conductivity, TiB2 containing MMCs is expected as innovative materials used as electric/ electronic components. Furthermore, as TiB2 has low density, high melting point, low thermal expansion and good deformation resistance, the development of high performance composites with multi-functional properties is expected. As thermal conductivity of pure Al and TiB2 are 225 and 66.4 W/mK, respectively, it is expected that the degradation of thermal conductivity by adding dispersant in Al matrix is suppressed. The authors have carried out a thermal conductivity, electrical conductivity, mechanical properties of 20 vol.% TiB2 dispersed Al composites (Sugio, 2016, Sasaki, 2016). In this study, the influence of quantity of addition of TiB2 on microstructure, thermal conductivity was studied minutely."

Jan 1, 2018

By Laura Kelsey

Contaminant Robust In Situ Water Extractor CRIWE Nafion-based water clean-up Extract purified water from natural extraterrestrial sources In situ water processing for downstream electrolysis Chemically resistant to process contaminants such as acid

May 1, 2013

"5.1. IntroductionThe sample preparation requirements for bulk analyses of platinum-group elements (PGE) are different from the requirements for ore microscopy and in-situ analyses. It is necessary that the initial sample collection results in as representative a sample as possible for both types of analyses. Ingamells (1980) believes, however, that sampling is always imperfect and that there is no such thing as a truly representative sample. Once collected, the usual low content and irregularly dispersed nature of the PGE require that samples for bulk analyses be made as uniform as possible, whereas in samples for ore microscopy and in-situ analyses the PGE must be concentrated. Because of the generally high specific gravity of platinum-group minerals (PGM), certain precautions must be taken, such as mixing the sample material in the bags prior to opening.5.2. Preparation forBulk Analytical MethodsThe principal factors that determine the size of the sample required for a bulk analysis are grade, heterogeneity and grainsize. Initially, the grade and sample heterogeneity can only be estimated and a sampling methodology is developed with experience. It is essential at all times, however, that the assayers have information about the source of the sample and the purpose for the analysis. Information on the grain-size, which can only be obtained through mineralogical analysis, is also very important for PGE analyses, but, unfortunately, is often ignored.5.2.1. Samples fromUnconsolidated DepositsConcentrations of PGE may occur in eluvial deposits as well as in a large variety of alluvial deposits, including those of fluvial and glaciofluvial origin. These deposits are often difficult to map and sampling is further complicated by the wide range, from sand-size to boulders, of the non-POE-bearing constituents, and by the irregular distribution and shape of the ""pay streaks"". PGE concentrations in unconsolidated deposits are largely composed of resistant Pt-Fe and Os-Ir-Ru alloys (cf. Cabri and Harris, 1975 and Raicevic and Cabri, 1976), thus making comminution to the usual-150 to -200 mesh somewhat unreliable, due to the malleability of these alloys."

Jan 1, 1979

By Gordon Sproule

THE papers presented to the Institute, and published in the BULLETIN, in the past three years, may be classified as follows: Geology, Mining, and Milling 89 or 58.5 per cent Smelting, Refining, and Refractories 17 " 11.2 " Mechanical and Physical Metallurgy 7 " 4.6 " General (Economics, Welfare, etc.) 39 " 25.7 " Total 152 100 These figure~ should be excuse enou.gh for. the present paper. As indicated by the title it is proposed: I.-To review briefly some of the more recent developments of Physical Metallurgy; and 11.-To show how Physical Metallurgy functions as the link between mining and production metallurgy on the one hand, and consumption engineering on the other hand. Io these days of specialization, papers of the kind being considered mostly gravitate to the American Society for Metals, the American Society for Testing Materials, the Institute of Metals, and the Iron and Steel Institute. In proof that there is a place for the newest and most specialized of these societies, the American Society for Metals, it may be said that in the Montreal Chapter there are 200 active members, and in the Ontario Chapter more than 200. Yet the overshadowing glamour of the mining industry proper, and the publicity it receives, result in an almost continuous dearth of students in metallurgical engineering at our universities. There are more jobs than graduates.

Jan 1, 1936

By K-A. Adamson

If fuel cells and hydrogen are to become a mass market reality a substantial amount of further research and development needs to be undertaken. Work in hydrogen storage, production, the economics of all aspects of fuel cells and hydrogen, materials balances, and product integration are just a few of the areas that are under focus. Setting R&D targets, and providing R&D funding are therefore areas that are central to the long term development of the market, and areas in which a number of governments worldwide are highly active. Some governments, such as Japan and Korea, have set a number of very ambitious, highly focused, long term targets and are backing this up with substantial funding, others such as the EU are working on a more integrated approach, wrapping some fairly fundamental R&D into large integrated projects which run in combination with a number of other market aspects, such as public acceptance and roadmapping. The US is slightly different, in that although is has a number of long term programmes and targets, FreedomCar and SuperGen being just two, the levels of funding are set annually with the passing of each years Fiscal Budget. This paper takes three high profile regions and analyses the R&D targets and funding levels for fuel cells and hydrogen. Criteria that will be looked at include: Time frame of target(s), level of ambition, funding issues, including: Funding windows, levels available, funding barriers, overall programme goals. The added value to this paper is that it will provide a clearer picture of where each region is heading, what are its strengths and weaknesses, in terms of R&D and where there may be areas for potential international collaboration.

Jan 1, 2005

By Zdenek D. Hora

British Columbia is an important producer of a variety of industrial minerals for both domestic and export markets. Some commodities such as limestone, dolomite, gypsum, calcium carbonate, silica, barite and magnetite are raw materials for well-established industries located in British Columbia, Alberta and northwestern USA. Others, like magnesite, sulphur, jade, asbestos, dimension stone and clay products, are mainly exported in processed form to overseas customers. Companies are developing markets for relatively new mineral products, including pumice, volcanic cinder and zeolites. A number of attractive geological targets have been identified by industry while research by government geologists has outlined the potential for refractory minerals, gemstones, garnet, nepheline syenite, carbonatites, residual kaolin, igneous apatite and peat.

Jan 1, 2001

By H. C. Gunning

Introduction The invitation to contribute a discussion on some of the broader features of the mineral deposits of our Cordillera seemed acceptable enough when presented several months ago. More mature consideration has impressed upon me the difficulty of making any constructive or very helpful contribution in the short time available and with my limited inspiration. Dr. Lang deserves our real gratitude for his general paper of nineteen pages at the beginning of the Volume. Into it, with the help of two diagrams and seven tabular summaries, he has packed a lot of useful information and has analyzed along several lines the data of the Volume's twenty-eight detailed papers on our mines and camps. He has added additional facts from his own knowledge of the region. I am sure that, like myself and the whole fraternity, he feels especially grateful to the eleven company geologists who found time to contribute detailed descriptions of mines they have studied. The Regional Situation With the Jubilee Volume and two recent publications of great value from the Geological Survey, we are more up-to-date on Cordilleran geology than we have ever been. But I would like to emphasize that we still have but fragmentary information. Brief study of G.S.C. Map 932A will illustrate this. Our knowledge of the Rocky mountains is limited to two narrow sections along the main railway lines, a somewhat larger area from the border north along the Mesozoic coal-bearing basins, and some reconnaissance along Peace river and the Alaska highway. There is some additional information on old maps, particularly those by G. M. Dawson, but it is very much of the 'exploratory' type. The other mapped areas are chiefly in the accessible region south of 'fifty-one', in the central part adjacent to and spreading north, recently, from the Canadian National railway, and along the edges of the Coast Range.

Jan 1, 1950

By Jiahao Xu, Namsoo P. Kim, Guikuan Yue

Iron (ferrous ions and ferric ions) plays an important role in the heap leaching of copper sulfide minerals and copper electrowinning. In our previous study, a novel oxidation-reduction potential (ORP) equation only based on the variables of temperature and nominal ferric/ferrous ratio was developed to predict the redox potential of the quaternary H2SO4-Fe2(SO4)3-FeSO4-H2O system, and its applicability was also extended to more complex acidic iron sulfate solutions, especially those generated during the acidic leaching and bioleaching of Printed Circuit Boards (PCBs) to recover copper. In this work, the broader range of applicability of this equation to other complicated acidic iron solutions containing copper ions has been extended and determined. Specifically, synthetic iron-containing solutions with copper ions according to the conditions of industrial electrolyte during copper electrowinning and heap leaching have been used to measure the ORP and test the developed equation. It seems that this equation can still be employed to predict the redox potential of the Fe3+/Fe2+ couple for the simulated solutions under conditions related to copper electrowinning and pregnant leaching solution generated during heap leaching over a wide range of solution concentration, nominal Fe3+/Fe2+ ratio and temperature. It has shown that the prediction and measurement of redox potential is highly useful to estimate and understand the iron chemistry of industrial leaching and electrowinning processes. INTRODUCTION It is well-known that iron (ferric or ferrous) ions are widely involved in the hydrometallurgical production of non-ferrous metals such as Cu, Au and Zn, mainly in the form of acidic iron sulfate solutions. As far as Cu is concerned, in a typical leaching-solvent extraction-electrowinning process, ferric ion plays a central role in the heap leaching process and is reduced to ferrous ions in the pregnant leaching solution. Ferric ion is the most important surrogate oxidant and the dissolved ferric/ferrous couple plays an important catalytic role in accelerating the leaching rate with oxygen as an oxidant (Peters et al., 1986; Schlesinger, King, Sole, & Davenport, 2011). In addition, during the traditional electro-winning process, oxygen is evolved at the anode, and copper is reduced at the cathode. A common idea is that iron in the electrolyte in copper electrowinning cell (with total iron of 1–4.4 g/L) plays an important role in reducing the current efficiency. According to the published results (Winand et al., 1975; Dew et al., 1985; Moats et al., 2009; Khouraibchia et al., 2010), thecurrent efficiency decreases linearly with increasing ferric ion concentration and the energy consumption increase was mainly caused by the decrease in current efficiency.

Jan 1, 2019

By R. C. Fernandes, F. L. Santos

Aluminum alloys in particular, have certain limitations when subjected to welding process. This is mainly present because aluminum alloys have high thermal conductivity, high contraction in solidification and high hydrogen solubility. Taking this into account, the FSW process has great potential for this application, since it is autogenous, held without metal melting and without the use of slags or shielding gases. From this concept, the aim of this study is to evaluate the joining of thin sheets of aluminum alloy 3105 H26 with 0.7 mm of thickness. To performing of the tests, some parameters were analyzed, such as: tool penetration in the sheets, attack angle, the type of welding tool and penetration control mode (position or force). The results indicated that the force control mode is most suitable for thin sheets, and the transient state at the beginning of welding was the most critical part to control the welding quality.

Jan 1, 2015