Search Documents

By K Inoue

The pressure oxidation of molybdenite concentrates in acidic and alkaline media has been studied. The conditions of the selective oxidation of copper and iron sulphide minerals with a quantitative copper leaching by ferrous-ferric-sulphate solution have been found and explained from the point of view of electrochemical kinetics. The partly oxidised residue consisting of molybdenite and (hydro-) oxide of iron (III) was then decomposed by oxygen in alkaline media. Effects of the main parameters, such us oxygen pressure, leaching temperature, solid-liquid phase ratio, autoclave stirring speed as well as lixiviants nature on the molybdenite oxidation rate have been established.

Jan 1, 2000

The geotechnical factors controlling the design of the open pit slopes of the Pasminco Century Mine near Lawn Hill, Queensland are presented below. Pasminco Century is a stratiform shale hosted zinc deposit in the Lawn Hill Formation that is overlain in part by the Thorntonia Limestone Formation. Both the mineralisation and overburden is located within a competent rock mass such that intact rock strength and discontinuity spacing is generally sufficient to prevent large-scale slope failure by breakage through the rock mass. Rather, overall slope stability issues are dominated by the major discontinuities within the rock mass. The deposit is located in a structurally complex regime, it consists of a synclinal basin which is truncated by easterly striking normal faults through its centre and northern and southern limits and by an unconformity on its eastern and western margins. Deposit geometry and slope stability is further complicated by small-scale folding, a pattern of northeast and southeast striking subvertical faults and north easterly dipping thrust faults with their associated fault emplaced blocks of Lawn Hill Formation in the overburden. The large size of the deposit requires a staged mining approach with the excavation of both final pit walls around the external sides of each stage and interim pit walls along the internal boundaries between adjacent stages. The deposit geometry and major discontinuities control not only the final pit wall design but also interim wall location and orientation, excavation sequence and in some stages the excavation schedule. Two and three-dimensional limit equilibrium stability analyses were conducted using both deterministic and probabilistic approaches to determine appropriate pit wall design criteria and to select a suitable excavation sequence and schedule.

Jan 1, 2000

By D Clarke, I Minniakhmetov

This paper describes the application of the SBRE framework to model the Olympic Dam deposit, one of the largest copper and uranium deposits in the world. Geostatistical simulations are the best practice for quantifying uncertainty in the mineral value chain and estimating resources. However, these simulations are currently undertaken on an ad hoc basis in the mining industry due to the high requirements in computing resources and capabilities in advanced geostatistics. The SBRE project provides a standard framework to test, build, and run conditional simulation workflows, which has been applied to the Olympic Dam deposit. Conventional geostatistical methods face challenges when modelling the Olympic Dam deposit, such as non-stationarity, non-linear correlations, and a large number of grid blocks to simulate. To address these challenges, a combination of methods was used, including projection pursuit multivariate transform, trend-residual decorrelation, pluri-Gaussian simulations, and turning-bands simulations. Various tools and applications were used to build the model, including in-house developed applications, Autovariogram software (Varify), and the RMSP python library. All computations were accomplished on the AWS cloud using the EC2-Batch service. The final set of simulations was validated using various methods, such as grade-tonnage curves, histograms, swath plots, and variogram reproductions, as well as validation using historical samples back-testing. The study highlights the importance of an automated, modular, and scalable framework in the development of conditional simulation workflows and describes the learning gained from trials of different combinations of methods and software

May 24, 2023

By M Zhu, G Tranell, N Simkhada, K Jakovljevic, M Wallin

Silicon is a vital element in many products today, such as electronic components, solar devices, high-quality alloys, and many others. The growing global demand highlights the need for the development of sustainable production methods to meet this demand as an alternative to the current carbothermic reduction, submerged arc furnace (SAF) based process. An alternative to this is the aluminothermic reduction of quartz in a CaO-SiO2 slag, which not only reduces direct carbon dioxide emissions but also promotes the utilisation of secondary raw materials such as quartz fines, aluminium dross and scrap as well as secondary alumina (SA) from dross recycling. In the current study, the effects of SA and CaF2 additions to slag on the resulting metal composition and metal yield were explored. Results were compared with thermodynamic simulations using FactSage™ 8.1. Experimental results show that, in agreement with thermodynamic simulations, the silicon content of the alloy is increased, while the Ca is decreased for starting slags where CaO-SiO2 is partly replaced by CaF2. Similarly, the addition of SA to the initial slag results in an alloy with a higher silicon content.

Jun 19, 2024

By I Grewal, M Lundt

Dense medium separation (DMS) is one of several preconcentration methods used for early waste rejection from run-of-mine ores at relatively coarse particle sizes prior to additional milling and beneficiation. DMS has been used extensively in the coal, diamonds, mineral sands, base metals and iron ore industries to produce either a final product or as a preconcentration step. Laboratory scale and pilot test work at the Met-Solve laboratory in Canada has demonstrated successful separation and upgrading of other minerals such as lead, zinc, copper and lithium based ores using DMS.This paper reviews historical dense media systems, results from the pilot-scale multi-stage DMS Separator “Condor” system, as well as production plants and associated laboratory heavy liquid separation (HLS) test work on various minerals. The mineral systems tested included a lithium bearing ore and a fluorspar ore. Other minerals were tested but are not reported in this paper.Pilot plant test work on a fluorspar ore showed that 41.6% of the mass could be rejected to the tailings stream while 95.3% of the CaF2 was recoverable to the product stream. On a spodumene sample that was tested, it was possible to reject 55% of the mass to tailings while recovering over 90% of the lithium.In recent market conditions and with the decreasing grades in existing ores, preconcentration should be a consideration to maximise the value of certain operations.CITATION:Lundt, M and Grewal, I, 2017. Dense media separation – a valuable process for preconcentration, in Proceedings MetPlant 2017, pp 122–130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By N Tuffs, R Peace, S Xue

Mine gas control is a major issue in most of the gassy underground coal mines, due to its direct impact on safety, production delays and cost of production. Analysis of the gas data, from different collieries in Australia showed that longwall gas emissions have increased substantially over the years. Simply increasing the number of goaf holes in the panel or decreasing goaf hole spacing seems not to be effective, in controlling high goaf gas emissions. A major research project has been undertaken by CSIRO in collaboration with mine sites to address this goaf gas control issue with the aim of developing effective and optimum goaf gas drainage strategies. The project has combined extensive field studies with computational fluid dynamics (CFD) models, to characterise goaf gas flow patterns and develop effective gas control strategies. The research work specifically involved review of gas control issues at field sites, goaf gas monitoring, tracer gas tests, CFD simulations and extensive field trials. Field demonstration studies of the new optimum strategies have been conducted at two collieries in Australia. The project results have shown that the optimum strategies were highly successful, in improving the overall efficiency of goaf gas drainage systems, at both the field sites. Results of the goaf gas flow characterisation studies and field demonstration studies are summarised in this paper.

Jan 1, 2005

By T Higuchi, T Yamamoto, K Takehara

Iron ore fines are used as raw materials for sintered ore for blast furnaces in the world. Since the production and quality of sintered ore have a great influence on the stable operation of a blast furnace, many technologies were developed for controlling the heat profile in the sintering machine, which largely affect the sintered ore properties. In particular, the influence of oxygen in the suction gas, which plays an important role in combustion, was investigated over the years. It is known that increasing the oxygen ratio by about 30 per cent not only significantly improves the combustion rate, but it also increases the strength and yield of sintered ore. However, the details of the mechanism for improving these qualities are unknown. In this study, we investigated the influence of oxygen enrichment at higher ratios (O2: 21–40 per cent) and tried to understand the sintering behaviour enhanced by oxygen. The effect of oxygen enrichment on sintered ore quality and the heat profile were evaluated by sintering tests using a quartz glass pot. From the results, sintered ore yield had a maximum value for O2 = 30 per cent, but strength was increased for O2 = 40 per cent. From heat pattern analysis, it is clear that the high temperature holding time also reached a maximum at O2 = 30 per cent. Furthermore, we found that with increased oxygen ratio, the combustion speed (flame front speed) was increased, but the area of combustion was enlarged. It is considered that there could be a maximum oxygen ratio value for the yield from the balance of these positive and negative effects on high temperature holding time. To clarify the reason for strength improvement, thermodynamic calculations were performed and it was found that melting behaviour could be improved by changing the oxygen ratio.

Sep 18, 2023

By B Washington, A Campbell, R Taylor

A sampling and measurement program was undertaken on the reaction shaft of the Olympic Dam copper flash smelting furnace. The object of the work was to provide information to validate a mathematical model of the burner and reaction shaft. Samples and measurements were undertaken through the burner inspection ports and the South East (SE) shaft sampling port about half way down the reaction shaft. Samples were collected to enable the calculation of particle loading of shaft gases, or sizing and chemical analysis of the partly-combusted feed, and the preparation of polished sections. Measurements were made of the temperature and sulfur dioxide content of the atmosphere, as well as plume velocity.To implement the program it was necessary to design and construct the following specialised items of equipment. For use at the burner inspection ports: a cup sampler for obtaining samples below the burners (temperature, solids loading and samples for characterisation).For use at the SE shaft sampling port and also at the settler level: trough sampler (plume definition and samples), isokinetic sampler (used as a velocity probe in this work), temperature probe (temperature traverses across the shaft), and sulfur dioxide probe (SO2 measurements across the shaft).The design of the sampling and measuring equipment is described, and examples are cited of the types of information obtained. The problems arising from working in a hot environment with molten or sticky particles are discussed.

Jan 1, 2005

By M F. L Gibson

The issue of flyrock is very important in the operation of all mineral extraction sites that use blasting. Unlike the other environmental effects of blasting, ground vibrations and air overpressure, flyrock is (or should be) a rare event, with severe consequences which may include damage to property, injury or fatalities. These physical consequences are often matched by a loss in public confidence in the management of the operation, mistrust and bad press. In this work a deterministic analysis of flyrock was carried out using the equations of a particle in motion with drag. The solutions to these equations were used to reproduce the curves of Lundborg et al (1975) for the relationship between flyrock boulder size and maximum ejection distance. A probabilistic approach based on Monte Carlo simulation was built up with the analytical model using published data together with local case study material. A typical quarry blast situation was modelled and estimates of safe standoff distances were determined using risk assessment techniques.

Jan 1, 2001

By I Gray

While in some cases it is vitally important to measure the virgin stress in rock prior to tunnelling there are a number of cases where such stress measurement is really not required. The concept of having to have a number to put in a numerical model representing a continuum is often quite inappropriate. This paper discusses the cases when virgin stress measurement is required and the most appropriate means to measure it. The techniques discussed cover all of the overcoring systems, hydrofracture and borehole breakout measurements. It also covers the use of rock surface stress measurement, which is easy to perform and should be used to check for changing stress conditions. Unfortunately this technique has been ignored in recent times because engineers are addicted to numerical models requiring far field stresses rather than measuring the real values that exist where they matter – at the tunnel wall. A case is presented in which the measurement of surface stress in a tunnel boring machine tunnel enabled the far field stress to be determined in what must be the world’s largest overcore.CITATION:Gray, I, 2014. The measurement of rock stress for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By O Dominguez

Significant value can be added to ore supplied from the mine to the mill by measuring its quality in real time and performing grade control additional to that within the mine. Responsibility for ore quality between the mine and mill stockpiles is not always clear due to operational siloes so geologists and mining engineers need to be involved collaboratively with metallurgists to optimise ore value prior to processing. Sensors, such as the GEOSCAN-M which utilises high specification Prompt Gamma Neutron Activation Analysis (PGNAA), that measure conveyed ore flow representatively (continuous and fully penetrative) and in real time have been used in the minerals sector since 2003 and have been successfully applied in multiple commodities. Quality can be measured within the mine where material is conveyed underground or in-pit. Bulk ore sorting is used to divert increments of waste from the ore stream to upgrade material sent to the crushed ore stockpile (COS) as well as to create run-of-mine (ROM) stockpiles of different qualities to maximise blending opportunities and accommodate processing priorities, eg blending out deleterious content. The real time composition measurement can be combined with moisture and fragmentation analysis data for improved ore type characterisation, to control ore blending, for feedback to the mining schedule and block model reconciliation, and feed forward control for grinding and processing operations. The paper discusses various parameters measured and derived in existing operations that are used to maximise coarse waste rejection and metal recovery, optimise plant feed quality consistency, and reduce consumables; power, grinding media, water, reagents, and minimise fine tailings generation. Innovative geometallurgy applications are also discussed.

Mar 22, 2022

By R Berry, S G. Walters, J A. Hunt, D Collett

The texture of an ore type is fundamental in understanding the metallurgical behaviour of an ore. This study will show examples of how quantified textural attributes (mineral shape, grain size and mineral association) can be obtained from automated and scanning electron microscope (SEM)-based microscopy and utilised using advanced image processing techniques. Examples will be shown of integrating quantified and semi-quantified meso- and macro-scale textural attributes as well as how they relate to texture-based visual logging systems. The implications of texture for processing behaviours such as comminution, liberation and recovery will be discussed. This research is part of a major collaborative geometallurgical project undertaken at the Centre of Excellence in Ore Deposits (CODES, University of Tasmania) and the Julius Kruttschnitt Mineral Research Centre (JKMRC, University of Queensland). The authors wish to acknowledge financial support and permission to publish from the sponsors of the AMIRA P843 GEMIII project.

Jan 1, 2008

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A Sellgren, M R. Carstens, R Visintainer

There is a wide variety of industrial pastes or non-settling slurries pumped in mining, dredging and reclamation projects as products, refuse and tails. The types and/or names of some of the common ones are alumina red mud, phosphate clays, tar sands mature fine tails, tar sands (CT) consolidated clays and fly ash. The pipeline performance or friction of these varies dramatically with the type, its concentration and the particulars of the actual slurry making it difficult to select pumping equipment and to design associated pipelines. The GIW Hydraulic Laboratory in Grovetown Georgia has tested a number of these slurries over the last 30 years for various mining customers. Where available in the public domain and/or where permission has been obtained, the results of those tests are presented in this paper in a form usable for pipeline and pump system designers and users.

Jan 1, 2005

By A P MACONOCHIE

The methods used and some of the results obtained from a major geotechnical study of the Ok Tedi mine area, Papua New Guinea, are described. The study was carried out at both regional and local scales and extended over a two-year period. A team of individual engineers and scientists from a variety of disciplines carried out the work. This study may provide a model for other investigations in similar environments.

Jan 1, 1992

By B E. Hall, J Poniewierski, A J. Hills

Following a review of life-of-asset work at MMG’s Rosebery mine in which a proposal to increase production from 0.8 Mt/a to 1.2 Mt/a was mooted, questions were raised as to the seemingly arbitrary reasoning for the production increase. They included: Did the proposal actually add value? Was the production rate from the mine sustainable? Was it the best identifiable value-adding configuration?A multiple scenario analysis study commenced to model how various cut-off grade values against mill throughput, along with associated capital expenditure, would impact on the potential value of the operation. This was carried out utilising the ‘hill of value’ approach promoted by AMC Consultants.The traditional approach to these studies uses a constant cut-off value (NSR – net smelter return) for the whole mine analysis. This was thought to potentially introduce a large amount of variability to the model as different ore types were thought to have different processing costs and different underground lenses were thought to have different mining costs. With the aim of developing a consistent value measure that would be comparable between the lenses, an alternative measure was suggested for all ore block values in this model, irrespective of lens location.The new measure used was a mine variable value (MVV). This allowed for the variable factors of final metal concentrate production to be removed from the ore value. From a mining point this was the haulage distance from ore source to run-of-mine (ROM). For the mill it was the amount of reagents required, varying based on grade together with the amount of power required for crushing, grinding and tailings handling.From the initial run of the model, preliminary results lead to a conclusion of increased value being gained by either increasing cut-off grade or increased mill throughput rate. The validity of the result was tested using alternative price scenarios, which although changed the absolute value achieved did not significantly change the identified value-adding strategies. The realisation of these value increases identified are however contingent on higher sustainable development rates being able to be achieved mine-wide, higher backfilling rates being able to be achieved and overcoming recognised ventilation constraints. Further detailed studies are being put in place to identify the practicality of overcoming these recognised constraints and achieving the higher-value strategies identified.The ongoing objective of the hill of value model built is to keep the model alive as a life-of-asset planning tool and to continue refining the foundation data, such that various mining strategies can be analysed with increased confidence.CITATION:Hills, A J, Hall, B E and Poniewierski, J, 2014. Mining scenario analysis and mine variable value, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By R Verreet

In April 2000 Mount Isa Mines installed hoist ropes of a new design on the double-drum winder at their P49 shaft. The ropes, CASAR Duroplast, were about three times as expensive as the previously used triangular strand ropes. The P49 shaft is situated at Mount Isa MinesÆ George Fisher Mine, located some 30 km north of Mt Isa. This shaft used the tried and proven 6 x 33 triangular strand style ropes. The rope life attained by these ropes at the time was acceptable due to many years of satisfactory performance. The following study indicates the improvement of service life using CASAR Duroplast rope in P 49 shaft, which depends on shaft and winder parameters of that particular shaft and cannot necessarily be generalised to other shafts.

Jan 1, 2005

By J Miedecke

A metalliferous mine has operated at Storys Creek from the 1890s to 1979. Storys Creek drains from a pristine catchment and National Park and remains as the most degraded stream from historic mining in north-eastern Tasmania. It has been the subject of public concern since the closure, particularly at times of high rainfall such as existed in 1985 and 1986. The mine is located on the banks of the creek, which flows into a major river, the South Esk River, which is one of TasmaniaÆs largest rivers and important for recreational fishing and water supplies. For much of the life of the of the operations tailings were directly discharged into the creek, and in latter years stockpiled or very close to it. Little rehabilitation was carried out at mine closure. The result was erosion and subsequent deposition on the banks of the creek downstream. Direct emissions of adit water and the consequential emission of contaminated ground water to the creek continue to affect water quality. Contaminant loads discharging from the mine and tailings comprise 70% of the metal load in the catchment and are by far the largest single source. Acidity data suggested that the introduction of systems to introduce alkalinity could be effective in ameliorating the residual acid drainage impacts in the Storys Creek catchment. After a period of investigations and trials which proved their effectiveness, treatments adopted have included the following: relocation of tailings to a constructed and clay capped disposal area and rehabilitation of tailings area; crushed limestone addition to stream flows; crushed limestone addition to creek banks and exposed tailings; sealing of a drainage Adit; and construction of an anoxic drain to generate alkalinity to surface waters draining to old mine workings. These innovative treatments have resulted in a marked improvement in water quality draining from the area. The anoxic drain is believed to be one of the few, if any, which has been constructed to have generated high levels of alkalinity from clean waters and offers a solution to the clogging problems experienced in such drains in the past. Similarly, the use of crushed limestone in an active stream has proved effective in buffering acid drainage and removing metals from solution.

Jan 1, 2003

The Mount Kasi gold deposit in Vanua Levu represents an epithermal, high sulphur, gold-enargite system occurring within a volcanic caldera of Middle to Upper Miocene age. High level breccia pipes flare upward and form flat lying, near surface, mushroom shaped sheets parallel and near to the present land surface. The upper portions of the pipes contain explosion breccias which are capped by sandy siliceous sinter-like beds and are cut by alunite veins. Outlying intercalated scoriasceous lavas and breccia sheets show evidence of subsidence within a shallow basin. Detailed mapping of breccia types, intensity of silicification and the presence of multiple quartz veining and enargite abundance outlined blocks of more consistent gold mineralization within the breccias. This work has provided a model for mineralization which will aid future exploration and ore reserve estimations. A significant eluvial concentration of gold occurs in soils overlying the breccia sheet.

Jan 1, 1987

By James JV, Petho SZ

The South Deep surface shaft system is being sunk to a final depth of 2750 in below surface and on completion will be the deepest single drop haft in the world. The shafts will intersect the target reef horizon at 2650 to below surface. In order to negate the requirement for a shaft pillar, which would he extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This kill limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will he stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill.

Jan 1, 1998