Search Documents

By J. F. Enrietto

It is shown that one cannot approximate the broad internal friction Peaks observed in the Fe-Mn-N system as the sum of a number of subsidiary Peaks and still vetain the concept of a single relaxation time. Furthermore, the approximation of manganese affectirg only nearest neighbor interstitial sites is shown to be incompatible with the experimental results. The results of this experiment show that the influence of manganese in the ferrite lattice extends over 3 to 4 atomic distances. NUMEROUS experiments have shown that the presence of relatively small amounts of substitutional alloying elements can profoundly affect the profile of the damping spectrum in the vicinity of the Snoek peak in bee metals.1-7 Dijkstra and Sladekl observed this phenomenon in Fe-Mn-N alloys where it appeared as a broadening and shifting of the Snoek peak to higher temperatures. The authors interpreted this as being the result of a superposition of two damping maxima—the normal Snoek peak, located at its usual position and having a normal half-width, and an interaction peak having a normal half-width, but occurring at a somewhat higher temperature. They prclposed that the interaction peak was caused by nitrogen atoms jumping from Fe-Mn sites to Fe-Fe sites, the Fe-Mn interstitial sites having one manganese and one iron atom as nearest neighbors, and the Fe-Fe sites having two iron atoms as nearest neighbors. They further suggested that the Fe-Mn sites had a lower energy than the normal Fe-Fe sites because of the presence of the adjacent manganese atoms. From the relative heights of the two postulated damping peaks, the dif-

Jan 1, 1962

Executive HENRY A. BUEHLER, Chairman ERLE V. DAVELER EDGAR RICKARD JOHN M. LOVEJOY WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUMB, Chairman E. E. ELLIS PAUL D. MERICA H. G. MOULTON, Consultant Admissions RALPH M. ROOSEVELT, Chairman GEORGE D. BARRON DONALD M. LIDDELL WILBER JUDSONW. D. B. MOTTER, JR.

Jan 1, 1934

By S. A. Wookey

More than 90 per cent of the ore produced by stoping at McIntyre is mined by horizontal cut-and-fill methods. The remainder is mined by square set and fill. In the stopes on the upper levels, mill holes are spaced 80 ft. apart and usually it is feasible to mine the breast for the full distance between the mill holes in one operation and to break, clean out and fill without any support for the roof or walls, other than the odd crown bar or sprag. The ore is scraped to the mill holes by small (10 to 15 hp.) air-operated slusher hoists. No grizzlies are used over the chutes and care is taken to break up the big pieces beforehand. Fill usually is spread by tramming sand or waste in a one-ton car from the fill raise. Fill raises are driven parallel to the strike of the vein and are inclined at approximately 48°. In long stopes, where more than one fill raise is necessary, they are spaced about 300 ft. apart. It is sometimes necessary to stand square sets for a short distance each way under the brow of the fill raise. support needed increases and on the lower levels and in some wide stopes where closer support of the back is necessary, it has become standard practice to timber the stope with 12 by 12-in. timber. Rough timber sets consisting. of caps, tightly blocked to the back and supported on posts 7 ft. high, are placed at about 5 ft. intervals. These sets are generally salvaged from the lower breast before blasting and are used again on the upper slice after the fill has been placed. In general, two or three breasts may be broken down before mucking out and filling and the ground stands long enough to enable this to be done safely. On the lower levels and in certain wide stopes and in heavy ground, a more intermittent method must be used. Only one breast or even part of a breast can be blasted and the back must be timbered before the ore can be removed. In these cases, sill timbers 16 ft. long, supported at one end on posts from the fill and at the other end on pins inserted in holes drilled in the face, are used. Timber cribs 5 by 9 ft. built from the fill to the roof and tightly blocked to the back are used throughout the mine to reinforce both the timber sets and the square sets.

Jan 1, 1946

JESSE L. JONES, ? Pittsburgh, Pa. (written discussion?).-From a commercial standpoint, the most important characteristic of the electric furnace is the ease with which it lends itself to intensive production. The melting of non-ferrous metals, as usually clone in crucible, open-flame, reverberatory, and similar furnaces, has certain disadvantages which are absent in the electric furnace, viz.:

Jan 4, 1919

By James Lorimer

THE topography at the Stan Trg mine facilitated early exploration by adits; in consequence adit levels were developed at horizons 865, 795, and 760 meters above sea level, and the levels in the mine 'are named according to their elevation. Exploitation started from the 760-m. level . upwards while simultaneously first steps were taken with regard to mining in depth. A deep dewatering adit 2.5 km. long now gives access to the deposit at the 610-m. horizon which also is connected with the 760-m. adit level by a three-compartment main hoisting shaft. Main levels have been developed internally from

Jan 1, 1936

By Theodor Zuschlag

Electrical prospecting is the art of exploring the structure of the subsoil in regard to conductivity variations and interpreting the results of such exploration as to their geological meaning. Electrical prospecting has been applied during the last few years with outstanding success, not only to prospecting1 for ore but also to structural studies.2 Both applications have proved helpful to the geologist, and the latter application especially promises to become of still greater importance in the future. The mapping of structures is the most important function of the oil geologist. Oil is lighter than water, therefore in water-bearing beds it will migrate upward until the migration is stopped by a bed impermeable to the oil. Geologic structures such as domes, anticlines, faults and terraces, offer good prospects in the search for oil accumulations and can be traced easily by electrical prospecting, provided they are composed of a series of sedimentary layers of which at least one possesses fair electrical conductivity and follows the general trend of the structure. Conditions for Successful Mapping The first condition, fair electrical conductivity, is met in almost any oil-bearing series, because generally the electrical resistance of a sedimentary bed is identical with the resistance of the more or less saline waters, filling partly or entirely the pores of the rocks.3 Briefly, the electrical resistivity of a bed can be expressed for all practical purposes by the product R X P, where R is the specific resistance of the waters in the rock pores and P a factor depending upon the percentage of water by volume in the rock. The specific resistance of any solution can be computed from the chemical analysis, being primarily a function of the

Jan 1, 1932

Member ship L P MATHEWSON, Chairman GEORGE D BARRON LOUIS D HUNTOON JOHN A CHURCH, JR H N SPICER Alternates LEWIS W FRANCIS WILBER JUDSON F T RUBIDGE Increase of Membership JOHN A CHURCH, JR, Chairman Other members to be appointed

Jan 1, 1923

By John W. Weeton, Donald W. Petrasek

Relatively few metal-metal systems exist that would permit the creation of fiber-metal composites consisting of mutually insoluble constituents. It is anticipated that most high strength-to-weight ratio and high -temperature fiber composites ultimately to be produced will utilize high-strength fibers embedded in a highly alloyed matrix. An investigation was conducted to determine the effect of alloying on the tensile Properties and micro-structure of tungsten-fibey-reinforced composites. Composites were made of tungsten fibers infiltrated with copper binary alloys that contain elements of varying solubility in tungsten. Room-temperature tensile tests were made on the composites, and a metallographic study of the microstructure of the fiber-metal-matrix interfaces was conducted. It was shown that, as the depth of penetration of some alloying elements into the fiber increased, a decrease in both tensile strength and ductility of the composite results. A notch effect, due to the formation of a brittle alloy zone with the tungsten fiber, was observed and gave rise to greater reductions in tensile properties and ductility behavior than would be Predicted by a law-of-mixture relation alone. In recent years, investigators have considered combining fibrous materials with relatively weak binder materials. The interest in fiber-reinforced composites results from the fact that fibers or wires may be exceedingly strong and exhibit mechanical properties superior to those of the bulk materials from which they are derived. For example, tungsten wires drawn to less than 1 mil in diameter may have strengths of over 600,000 psi,' while steel wires ranging from 10 to 3 mils in diameter may have strengths of the order of 300,000 to over 600,000 psi.2 Both metallic and ceramic whiskers are known to have very high strengths. For example, iron whiskers have been shown to have strengths of 1.9 million psi3 and sapphire whiskers have been reported to have strengths of the order of 1.7 million psi.4 If all or part of the strengths of such fibers could be retained, subsequent to the incorporation of the fibers in an engineering material, a superior material could result. In previous work done at the Lewis Research Center, McDanels, Jech, and weeton5 demonstrated the feasibility of fabricating metal-fiber—metal-matrix composites that utilized the full strengths of the fiber and matrix materials. Tungsten fibers were combined with a copper matrix by a liquid-infiltration method such that the tungsten fibers were uniaxially oriented parallel to the tensile axis of the composite. A linear relation was established that related the tensile strength of the composite with the volume percent of the fibers. Mutually insoluble constituents were selected for the study so that the strength of the composite could be quantitatively related to the strength of the individual constituents. The fact that there are only a few metals that are mutually insoluble with tungsten, e.g., copper, silver, gold, and zinc, and that these either have low melting points, high vapor pressures, or poor oxidation resistance, makes it necessary to utilize other metals that are soluble in tungsten, where high-temperature applications are ultimately contemplated. It was anticipated that, for most practical fiber-reinforced composite materials, it would be necessary to use a fiber and metallic matrix that would have varying degrees of solubility for each other. A logical extension of the earlier work was thus felt to be a study that would determine the effects of elements that had mutual solubility with the tungsten. Numerous investigators have found that tungsten fibers may be damaged by thermal treatments or contamination of the surface of the fiber by alloying elements.6-10 On the other hand, surface treatments may improve the strength of such fibers."-" Relatively little work with composites containing tungsten fibers have been reported. The work of parikh14 has shown that kinked, short-length tungsten, steel, and molybdenum fibers could str'engthen such matrices as silver, gold, and copper. Some of the combinations of fibers and matrices studied by

Jan 1, 1964

By Charles Clayton

CAST-STEEL runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Foley1 found not only the usual ingot structure, but zones of Widmannstattian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent, nickel and 0.350 per cent. carbon and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. The macrostructure, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregation of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of- the runner and in all parts of the individual grains. I he tipper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to- some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 3, 1920

By Arthur Taggart

FLOTATION of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest clays of flotation that certain of the nonsulphide nonmetal minerals-e.g., sulphur and graphite-would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection,1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis.4,5,6 Air levitation? of certain oxidized minerals, both metalliferous? and nonmetalliferous, and separa-tion thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years.7 This paper presents evidence that the principles underlying the air levita-tion of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentra-tion, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levita-tion, The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material.

Jan 1, 1937

By Brison Robertson, W. P. Fishel

The carbide-forming tendencies of the various steel-alloying elements, or their affinities for carbon, is a subject that has received considerable attention, but little more than a probable arrangement of the elements as to their carbide-forming tendencies has been proposed. The physical properties of alloy steels depend upon the relative proportions of the elements present and their combinations. one important phase of this subject is the distribution of carbon between the various elements present. The distribution of car. bon between iron and other elements evidently sill depend upon: (I) the affinity of each for carbon; (2) the relative atomic masses of the elements present; and (3) the possible formation of compounds between the alloying and iron and between the elements themselves, In ternary steels the case is simplified, especially in systems in which the element and iron form no compounds, In such systems iron and the alloying element are competing for the carbon present. In this work the distribution of carbon between titanium and iron has been studied by measuring the relative amounts of iron carbide and titanium carbide present ill a series of annealed steels in which the ratio of titanium to carbon extended from 0.527 to 4.61. Ten Fe-Ti-C alloys, weighing about 250 grams each, were prepared by melting under a Vacuum, in an Induction furnace, Armco iron, carbon-free ferrotitanium (25 per cent Ti), and pure carbon. Vacuum melting prevented the formation of titanium oxides and nitrides, which would the the problem. The melts were made in graphite crucibles lined with sintered magnesium oxide. The ingots were the in the furnace under a vacuum and "'ere then completely annealed at 950°C. The determination of the amount of titanium carbide present was based upon the established insolubility of titanium carbide in boiling dilute (1:4) sulphuric acid, and the complete solubility Of free titanium and titanium-iron compounds in this acid. High-carbon ferrotitanium, which had been treated to remove free Ti and Fe. was found to be completely insoluble in the acid; and the carbon-free ferrotitanium used in making the alloys was found to be completely soluble. Others have reported the insolubility of titanium carbide in sulphuric and hydrochloric acids. Turnings from the ingots were digested with boiling sulphuric acid (1:4) until all action had ceased. The carbide residue was filtered off and analyzed for titanium, and in some cases for carbon. This represerifs the titanium that was united with carbon The filtrate from the carbide residue contains the portion Of the titanium that was in solid solution in the ferrite. Titanium

Jan 1, 1945

By Ben-Zion Weiss, Melvin R. Meyerson

FATIGUE crack propagation in some aspects can be viewed as being a result of localized plastic deformation concentrated near the tip of the crack.' Deformation is influenced by microstructure which in turn can affect the fatigue crack growth significantly. To study the effect of localized microstructural changes on fatigue crack propagation, cantilever-type notched specimens were subjected to cyclic bending at constant load amplitude. The extent of fatigue crack propagation was obtained by measuring the length of the crack by periodic observation with a microscope on the polished side of the sample,2"4 and these data were used in preparing the curves in the figures which follow. Figs. 1 (solid lines) and 2 show experimental results obtained in austenitic type 302 stainless steel containing higher than standard carbon (0.24 pct C) and 310 stainless steel. Both steels were homogenized for 8 hr at 1120°C and then water-quenched in order to prevent the precipitation of carbides. Fig. 3 shows experimental results obtained on 9440 low alloy steel in the normalized condition and in the quenched and tempered (580°C) condition. Indications of microstructural influence can be seen in scattering of the experimental data. The degree of scattering depends on both the microstructure and the amount of cyclic stress applied to the sample. For microstructures which are more easily deformed plastically, e.g., normalized or annealed as compared with hardened and tempered structures, the scattering is greater. Similarly, higher stresses produce greater scattering in the results, regardless of whether the cause of the stress increase is due to initial loading conditions or the growth in crack length. Scattering is believed to be a result of partial redistribution in the stress field around the tip caused by plastic deformation. This opinion is borne out by much smaller scattering of experimental results in the austenitic 302 high-carbon (0.24 pct C) steel. In this steel, plastic deformation in the neighborhood of the crack causes partial mar-tensitic transformation of metastable austenite,5 which in turn restrains further plastic deformation. As a result, the stress redistribution around The tip is reduced. Partial martensitic transformation was confirmed

Jan 1, 1969

By Charles Hardy

ACTIVATED alumina is an aluminous material which may be 1 classified chemically as a partially dehydrated aluminum trihydrate having a high porosity and a perma¬nent physical structure. In general, it may be employed effectively and economically for the complete removal of water vapor from gases and vapors; for the selective adsorption of certain as especially those of the higher boiling points, and as a catalyst or catalyst carrier. Other forms of alumna are available and may be employed similarly but not so effectively nor can reactivation be accomplished with uniformity over many cycles without deterioration. The adsorption-reactivation cycle of activated alumina can be repeated many times without any apparent depreciation ill

Jan 1, 1934

By Wilhelm Rohn

When a metal solidifies, gas, initially present in solution, may be concentrated at the grain boundaries, leading to brittleness, or it may form solid compounds which, if localized at the grain boundaries, impair the properties. On the other hand, the solid compounds formed sometimes distribute themselves more or less uniformly, and hence may be relatively harmless. If metallic oxides are heated under a partial oxygen pressure less than that corresponding to the dissociation pressure of the oxide in solution in the melt, they will decompose and oxygen will tend to be eliminated from the melt. This paper presents data on the partial oxygen pressures of copper and nickel oxides over a wide range of temperatures; it also presents data regarding the amount and nature of the gases evolved in the vacuum melting of a 3500-kg. charge of nickel-chromium alloy and gives test values indicating the improvement in impact values ascribed to vacuum melting. The results of commercial experience with a 4-ton vacuum melting and casting furnace indicate that this method entails an increase in cost of about 10 cents per pound of ingot over orthodox practice, which may be justified for special products and may be lowered if hot metal is charged into the vacuum furnace. DISCUSSION (Howard Scott presiding) J. H. ScafF, New York, N. Y. (written discussion).—In the section of Dr. Rohn's paper describing the effect of melting -metals in vacuo, he says, "In this way plain copper, nickel and iron may be easily purified. For example, vacuum-melted copper does not contain any oxygen and for this reason it is never sensitive to hydrogen embrittlement." This statement is contrary to the results of our experiments at the Bell Telephone Laboratories on the effect of vacuum melting on the properties of copper. Several 150-gram samples of tough-pitch copper were melted in a vacuum of the order of 1 X 10-5 to 1 X 10-6 mm. Hg for 2 hr. Portions of the ingots obtained were swaged to 0.100 in., then drawn to wire 0.050 in. in diameter for physical and

Jan 1, 1933

By Eric Sinkinson

MANY of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining' of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally. enclosed in serpen-tine masses, somewhat decomposed, and in mining it wall rock is inci-dentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18° C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18° C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H20) or (4MgCO3.Mg(OH)25H20), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2, The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates.. The range in published figures for solubility

Jan 1, 1936

By R. W. Raymond

[NOTE.-This paper was presented at the Pittsburgh meeting in a partially completed form, and I fully expected to obtain, before the period of its publication, both the data and the leisure required for its completion. The hygiene of collieries was to have been separately considered, and the sanitary conditions of various metallurgical industries connected with mining were to receive an extended discussion, while at the same time the points treated in the paper as presented at Pittsburgh were to have more ample illustration from American and European sources. Delay in obtaining expected information, and the continuous pressure of professional work, have prevented hitherto the execution of this plan ; and I can now publish only a portion of what I had designed to contribute to the subject. In the meantime this portion, but slightly changed, has been included as a chapter on the Hygiene of Metal Mines in a work entitled Hygiene and Public Health, edited by Dr. A. H. Buck, of New York. An excellent chapter on the Hygiene of Coal Mines, contributed to the same work by Mr. Henry C. Sheafer, of Pottsville, affords me an opportunity to supply one of the deficiencies above alluded to. Mr. Sheafer's chapter contains much material in the way of explanations not required by professional readers; and he moreover devotes a considerable space to the explosive gases, falls of roof, and other causes of accidents to life or limb-a branch of the subject not belonging strictly to hygiene. I therefore make extracts only from his treatise.-R. W. R] IT is convenient to divide mines, with reference to this subject, into two classes, collieries and metal-mines. Subterranean quarries, rock-salt mines, etc., present no conditions requiring them to be separated from the latter class.

Jan 1, 1880

By S. D. Michaelson, Eric Sinkinson

Many of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in serpentine masses, somewhat decomposed, and in mining it wall rock is incidentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18" C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18" C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H2O) or (4MgCO3.Mg(OH)25H2O), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1938

By S. D. Michaelson, Eric Sinkinson

Many of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in serpentine masses, somewhat decomposed, and in mining it wall rock is incidentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18" C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18" C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H2O) or (4MgCO3.Mg(OH)25H2O), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1938

By S. R. Goodman, Hsun Hu, R. S. Cline

The quenching technique has been used to study phase relations in the composition area 2FeO.SiO2-FeO-SiO2-MnO.Si02-ZMnO.SiO2 of the system iron oxide-manganese oxide-silica under strongly reducing conditions such as exist in a gas mixture consisting of equul parts of carbon dioxide and hydrogen. Liquidus and solidus temperatures of most mixtures in the composition area studied are in the range of 1173° to 1345°C. EQUILIBRIUM relations existing among the oxides of iron, manganese, and silicon are of particular interest in two areas of steelmaking: slags and ingot inclusions. Mixtures of these oxides represent about 90 pct of the slag in the acid steelmaking process, and so dominate the chemistry of the whole refining process. These constituents also play an important role in the early slags existing at the time of the "lime boil" in the basic open hearth process. If these slags are liquid, they "wet" the lumps of lime rising from the bottom of the bath, and react with them. A liquid slag rich in CaO is then formed at the very beginning of the refining. Because the temperature is still low, all conditions for a good dephosphoriza-tion are fulfilled at this stage of the operation. Metal deoxidized with ferromanganese or silico-manganese is likely to contain, as inclusions, phases made up from among the oxides of iron, manganese, and silicon. A knowledge of stability relations existing among the phases present in this system, therefore, enables one to predict the hardness of the inclusions encountered. Moreover, because the shape of the inclusions in steel has a profound influence on the physical properties of the metal, it is important to establish whether or not the oxidic material is present as liquid or crystalline phases during heating and rolling of the steel (-1150 to 1350°C). A knowledge of melting relations in synthetic mixtures of iron oxide, manganese oxide, and silica will give a clue to these problems. Methods for determining such relations and the results obtained are described iln this paper. I) PREVIOUS WORK A number cf previous studies have dealt with the three "binary"* systems bounding the system iron oxide-mangar,.ese oxide-silica. The system iron oxide-silica was studied by Bowen and shairerl in 1932. Their data were obtained by equilibration of mixtures in contact with metallic iron. Phase relations for the system iron oxide-silica ill atmospheres of different oxygen pressures car1 be derived from data on the system FeO-Fe2O3-SiO2 as determined by Muan.2 The diagram shown iri Fig. l is a section of this system in an atmosphere of CO2 and H2 in ratio 1:l. The system manganese oxide-silica has also been the subject of several investigations. Most of the early studies suffered from a lack of proper control of the atmosphere under which the equilibrations were carried mt. Phase diagrams for the system at two well defined levels of oxygen pressures have been determined recently. Glasser3 determined stability relations in an atmosphere consisting of carbon dioxide and hydrogen in ratio 5:1, diagram Fig. 2, and Muan4 studied phase relations in the system in air.

Jan 1, 1962

By Eric Sinkinson

MANY of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in-serpen-tine masses, somewhat decomposed, and in mining it wall rock is inci-dentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumna, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18° C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact; MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18° C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H20) or (4MgCO3.Mg(OH)25H20), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1936