Search Documents

By J. F. Kemp

PAGE I. Introduction,.......269 11. Topogmphical Features,.....270 III. Geological Relations of the Mineralized Area,.272 1. Structural Features,.....272 2. Occurrence of the Copper,....274 3. Granite-Contacts,.......274 IV. Descriptions of the Rocks,.....274 1. Granite,........274 2. Limestone,.......276 3. Porphyritic Eruptions,.....278 (a) Quartz-Porphyry,.....278 (b) Trachyte-Porphyry,.....280 V. Contact Phenomena,......285 1. Comparative Immunity of the Limestone, . 285 2. Contact Phenomena in the Quartz-Porphyry,.... 285 3. The Form and Distribution of the Ore-Bodies,290 VI. Method of Deposition,......293 I. Introduction. The White Knob copper-deposits are situated about three miles south of Mackay, on the Salmon River branch of the Oregon Short Line Railroad, in Custer county, Idaho. An outline-map of this district is given in Fig. 1. The deposits have been known and spasmodically worked for many years, and a total of over 3.5 miles of tunnels, shafts and other workings has been driven with a view to their development. These extensive excavations have exposed the deposits sufficiently to permit a careful geological examination. The peculiar features which give special interest to this paper are the branching, tree-like form of the ore-bodies; the absence of zones of secondary enrichment in the partly oxidized pyritic deposits, and the fact that while the deposits are associated in a general way with the contact of an eruptive rock with limeetone, which it penetrates, the garnetization has taken place not in the limestone, as is the usual case, but in the igneous

Jan 1, 1908

The library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 1, 1919

By R. B. Woodworth

In the sinking of bore holes, there are but two fundamental operations —drilling and hoisting—which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of pqtroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the drilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 1, 1916

By C. W. Lawr

THE ores mined by the Santa Gertrudis Co. at Pachuca, Mexico, are mainly silver-bearing; they also yield some gold and carry a little copper. Strong cyanide solutions are used to dissolve the silver and gold, and the mechanical loss of cyanide at the tailings filter has been considerable. Prior to the year 1923, the pulp, after agitation, was given a 35 to 37-min. wash with barren solution in a Butters-type leaf filter; the discharged slime cake was repulped and pumped into eight Merrill self-sluicing slime presses in which the slime was given a further wash with barren solution for 25 to 35 min., followed by a 10-min. water wash. At that time the barren solution titrated around 0.350 per cent. free KCN and 0.500 per cent. total KCN. (Aero brand cyanide is used.) It can readily be seen that a 10-min. water wash would leave considerable cyanide in the filter cake, which of course was a total loss. This averaged 0.522 kg. (1.15 lb.) KCN per ton of solution. As the daily discharge to. the dam was 1600 tons1 of slime of a 2: 1 ratio of liquid to solid, the value of this mechanical loss of cyanide was an important item and its recovery held alluring possibilities.

Jan 1, 1929

By E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are presented in some detail. Basic principles ,are correlated with present practice for both the anthracite and the bituminous coal fields, and methods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various methods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment. DEFINITION OF TERMS Definitions of terms are consistent with modern developments, and on form, in general, with their usage in mineral-dressing practice. Because of variations in coal-preparation methods, it is impossible to define a rigid upper limit of particle size for a coal slurry or sludge which will apply generally. Limits vary somewhat with the particular treatment method employed at a given plant. For purposes of definition, this limit is chosen as the particle size for which preparation methods such as Chance cones and jigs are usually dispensed with, and other methods, such as the Hydrotator, tables, and froth flotation, are employed. Generally the limit will be 10 to 6 mesh. In assuming this variable upper limit of particle size in a coal slurry, it is recognized that the size ranges discussed will duplicate sizes dealt with

Jan 1, 1943

By Reno H. Sales, Charles Meyer

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the scricitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte's Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.' Introduction From the economic viewpoint it is highly desirable that much effort be expended for the purpose of increasing our knowledge of ores and their origin. It has been the observation of the senior writer, many times expressed, that the mining companies have spent too little money in research on the geology of nature's deposits of copper, lead, and zinc, which we know to be of limited extent and which, when exhausted, must be replaced by new discoveries. Experience at Butte and elsewhere has forced the conclusion that observation and mapping in the field must be supplemented by laboratory work if we are to arrive at a reasonably correct understanding of the geology of ore bodies and their environments. It is only through the medium of such correct understanding of geology that we shall be able to accomplish the maximum toward aiding mine operations and at the same time provide a proper background for field examination work whether it be geological or geophysical. The Anaconda Copper Mining Company's answer to the need above expressed has been to equip a geological laboratory at Butte. The reason why Butte was selected is obvious, for situated there is one of the world's largest and geologically most interesting concentrations of copper and zinc. Furthermore, because of the great extent of underground workings both laterally and vertically, the opportunities for observation and study of ore occurrences probably are unequaled anywhere. The laboratory was established with five principal objectives in view. These were: 1. As an aid to Anaconda Company mine operations at Butte and elsewhere, this work to supplement that of the mine geologists. 2. To aid in acquiring as complete an understanding as possible of the behavior of Butte veins and ore bodies laterally and in depth.

Jan 1, 1949

By Charles Meyer, Reno H. Sales

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the scricitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte's Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.' Introduction From the economic viewpoint it is highly desirable that much effort be expended for the purpose of increasing our knowledge of ores and their origin. It has been the observation of the senior writer, many times expressed, that the mining companies have spent too little money in research on the geology of nature's deposits of copper, lead, and zinc, which we know to be of limited extent and which, when exhausted, must be replaced by new discoveries. Experience at Butte and elsewhere has forced the conclusion that observation and mapping in the field must be supplemented by laboratory work if we are to arrive at a reasonably correct understanding of the geology of ore bodies and their environments. It is only through the medium of such correct understanding of geology that we shall be able to accomplish the maximum toward aiding mine operations and at the same time provide a proper background for field examination work whether it be geological or geophysical. The Anaconda Copper Mining Company's answer to the need above expressed has been to equip a geological laboratory at Butte. The reason why Butte was selected is obvious, for situated there is one of the world's largest and geologically most interesting concentrations of copper and zinc. Furthermore, because of the great extent of underground workings both laterally and vertically, the opportunities for observation and study of ore occurrences probably are unequaled anywhere. The laboratory was established with five principal objectives in view. These were: 1. As an aid to Anaconda Company mine operations at Butte and elsewhere, this work to supplement that of the mine geologists. 2. To aid in acquiring as complete an understanding as possible of the behavior of Butte veins and ore bodies laterally and in depth.

Jan 1, 1949

By G. R. Fitterer

NonmEtallic inclusions in steel have received much attention by metallurgists during the past few years. Many investigators have been emphatic in stating their belief that these impurities are the chief causes of steel failures, while others think that their effects are negligible. One of the main reasons that definite information on the effects of these impurities is lacking is that no reliable method has been developed for the exact determination of the amounts of these different impurities in steel. Some valuable new information has been brought out by a reliable method for nonmetallic inclusions which has been developed at the Pittsburgh Experiment Station of the U. S. Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board. This procedure satisfactorily extracts some of the more common inclusions from steels, thus enabling the investigator to correlate steel failures with inclusion content. Although the data given herein are the first to be published on the subject of the electrolytic extraction method, the interest in the subject is evidenced by the fact that it is already being used by some 20 to 30 steel companies for their various purposes. Some of the comments received from these laboratories indicate that the method is highly satisfactory: the unfavorable comments, when traced to their sources, have been found to be based on some small mistake made in either installation or operation. The chief discrepancy seems to have occurred in attempts to apply the method to the extraction of inclusions from alloy steels. The procedure can be used only for the plain carbon steels and for such low alloy steels as those containing the usual amount of copper (0.2 to 0.3 per cent). Steels containing the carbide-forming alloys such as chromium, tungsten, etc., present far too many difficulties for the accurate determination of inclusions. Luckily, the iron and manganese carbides do not offer any difficulties and no contamination of the oxide-sulfide residue results, It is highly probable that some modification of the following

Jan 1, 1931

By R. F. Domagala

SOME of the results of a program designed to study the kinetics of transformation and related mechanical properties of prototype Zr-X binary alloys systematically are presented here. The object of this program was to provide a sound basis for a scientific approach to the realization of optimum properties in binary zirconium alloys. Alloys of Zr-Mo (eutectoid), Zr-Sn (peritectoid), and Zr-Ti (a and ß isomorphous) were prepared and studied. The data herein are confined to a presentation of the results of studying the eutectoid prototype alloys. The Zr-Mo phase diagram has been determined.&apos; A definitive metallographic study of isothermaily annealed samples prepared from high purity elements served to position a sluggish eutectoid reaction, ß?a + ZrMo2, at 780°C. The compositions of the phases involved in this reaction are: ß, 7.5 ±1 pct Mo; a, <0.18 pct Mo; and ZrMo2, 67.8 pct Mo. Inasmuch as a lower purity sponge zirconium was used in this work boundary placements were rein-vestigated with the less pure alloys. Materials and Procedures Hafnium-free sponge zirconium was used to prepare all ingots. The arc melted hardness of a small button of this zirconium was found to be Vpn 168. Chemical analyses conducted at Armour Research Foucdation are shown in Table I, High purity molybdenum sheet was used as the alloy addition. A typical analysis is shown in Table I. Several 200-g Zr-50 pct Mo alloys were made by arc melting. Crushed granules of this material were used to ensure inqot homogeneity Ailoy ingots were prepared by double melting techniques. First, three 5-lb ingots of each alloy composition were are melted in 2 nonconsumable electrode arc furnace. After melting. the ingots were ground to remove surface defects. A subse-

Jan 1, 1958

By W. H. Bassett, J. C. Bradley

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (I) Depth of deoxidation of copper heated in reducing gas is grealer the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this diflerence in depth of deoxidation is thai, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much more rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900" C.; that is, deoxidaion is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide presenx in the copper. In 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By F. E. Bash

CONSTANTAN is an alloy of copper and nickel that is extensively used, under a number of trade names, as a resistance wire with a low temperature coefficient of resistance, and one of the elements of base-metal thermocouples, iron usually being the other thermoelement, although for low-temperature work copper is also used. Before the war, constantan was imported, in common with many other technical necessities. Since it required considerable time to receive the constantan after it was ordered, fairly large stocks were kept on hand; but after the beginning of the war no more was imported acid the stocks of foreign material were exhausted about the same time that the steel and munition manufacturers began to need great quantities of it for thermocouples for the heat treatment of steel. To meet this demand, the International Nickel Co. began manufacturing constantan that met all the requirements of the users of resistance wire but did not give the same electromotive force against iron as the German material and consequently could not be used with instruments calibrated for a definite e.m.f.-temperature relation. It so happened that all the constantan made had an e.m.f. lower than that necessary to meet the specifications of the Leeds & Northrup Co. for whom this investigation was carried out. If some had been higher and some lower, good wire could have been obtained by a, process of selection, but as it was no wire at all could be procured. To remedy this situation, a thorough investigation was started with the close cooperation of the International Nickel Co. and the Electrical Alloys Co. The specifications to which the constantan had to conform were that it should give an e.m.f. of 47.40 millivolts. against pure iron at 1500° F. (816° C.) with the cold-junction temperature at 0° F., or a proportional e.m.f. at temperatures near 1500° F. The method of checking a wire was as follows: It was first welded to a piece of iron wire; Armco iron was found to be satisfactory but iron with greater than 0.1 per cent. carbon would give a lower e.m.f. against the same piece of constantan than pure

Jan 9, 1919

By J. J. Kantner

CREEP investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that applica-tion of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and struc-tural character of the solid metal.

Jan 1, 1937

By D. E. Peacock, B. Harris

The mechanical behavior of a niobium (columbium)TUNG alloy containing 20 wt pet Ta. 15 wt pet W, and 5 wt pct Mo has been studied in the temperature range 77° to 423°K. All specitrzens tested, apart from those into which oxygen was introduced deliberately, were fully recrystallized at 1500°C, had an average grain diameter of approximately 0.03 mm, and a combined carbon, ox-vgen. nitrogen, and hydrogen content of not not more than 250 ppm The meckatnical behavior of this alloy was found to be similar in seine respects to that of unalloyed bcc transilion metals. Both yield and flow stresses were sensililae to changes in deformation rate and both increased rapidly as the temperature was lowered below 150°C. A detailed examination revealed, however, that most of the temperature dependencc of the yield stress could be accounted for by the temperature dependence of the elaslic, modulus, whish is not true of the unualloyed metals. In lension at moderate strain rates, the trunsition fvom ducfile to hvittle behavior occurred just belour room teunperature bur incveasing the oxygen content from 190 to 200 pptn raised the transition temperature to about 4000K. TUNGSTEN and molybdenum have been found to be very effective high-temperature solid-solution strengtheners of niobium, but the amounts of these elements that can be added are limited if the alloy is to retain useful room-temperature ductility. It has been shown, however, that partial replacement of niobium with tantalum lowers the ductile-to-brittle transition temperature of such alloys and allows larger additions of molybdenum and tungsten to be made. Some of the high-temperature properties of niobium alloys containing these elements have been reported by Bartlett et al.,&apos; and the work presented here describes the low-temperature behavior of one of these, a solid-solution alloy containing, by weight, 20 pct Ta, 15 pct W, and 5 pct Mo. The elastic modulus, the temperature and strain-rate dependence of the yield and ultimate tensile stresses, and strain-hardening effects are discussed and compared with those of unalloyed niobium. EXPERIMENTAL MATERIAL AND PROCEDURE The material used in this investigation was produced from a 6-in.-diameter, double arc-melted ingot. This was can-extruded at about 1150°C to a 3-in.-diameter billet, and after annealing for 1 hr at 1345°C the billet was heated to 1315OC and part rolled and part forged to 0.5-in.-thick plate. The resulting material exhibited a cold-worked structure

Jan 1, 1965

By James Douglas

This sketch of the history, geography and topography of the American transcontinental railways is based upon a paper read many years ago by the author before the American Geographical Society, and now re-cast, with numerous modifications and additions required to bring it up to date. It was intended primarily for the information of members and guests of the Institute from the East attending the California meeting; and, with that purpose in view, the Secretary of the Institute compiled;

Jan 1, 1900

By A. F. Knoll, T. Clinton Taylor

Qualitatively, galena (native lead sulfide) reacts with aqueous solutions of the xanthates,1 and has its surface sufficiently altered so that there is a tendency for air bubbles to attach themselves to the mineral crystals where there was no such effect before the treatment. This property is utilized in froth flotation operations where the mineral sulfide particles are raised into the froth and the gangue whose surface is not altered remains behind. The results of a study of this reaction were reported2 recently and certain tentative suggestions about the interaction of galena and the alkali xanthates were offered. In this paper, there is set down the results of a detailed quantitative investigation of the ions involved in this interaction with a view to finding out more about the condition existing immediately at the surface of a crystal like a heavy metal sulfide after treatment with an organic reagent. Past experimental experience showed that finely ground galena shaken with aqueous potassium xanthate abstracts xanthate ion and at the same time sulfate ion, reducing ions of the type (SmOn)= where the ratio of m to n is less than 4:l (as in sulfate), sometimes hydroxyl ion, are thrown into solution.3 Ions Involved in Xanthate-galena Interaction The present quantitative study of the galena-aqueous potassium xanthate system shows that at the lower concentrations of potassium xanthate (less than about 25 mg. per liter) the amount of xanthate ion abstracted by the galena can be accounted for by the amount of reducing ions of the (SmOn)= type and sulfate ion thrown into solution. At these

Jan 1, 1935

By M. S. Smani, P. Blazy, J. M. Cases

Investigations on the beneficiation of sedimentary Moroccan phosphate ores are reported in four separate parts. The first discusses electrochemical phenomena at the solid-aqueous solution interface for minerals of the apatite group. In the second part, the electrochemical properties of the calcareous gangue associated with the phosphate ore are investigated. The flotation of calcite and phosphate oölites, using both anionic and cationic collectors, is discussed in the third part. It is shown that selective recovery could be obtained for precise concentrations of collectors and pH ranges. Results of work aimed at optimizing depression of phosphate oölites during inverse flotation of the carbonate gangue with sodium oleate are reported in Part 4.

Jan 1, 1976

By A. M. Rahm

PROBABLY the majority of red brass sand castings are judged merely on the basis of outside appearance and the quality of machined surfaces. Many castings, however, must individually withstand a hydraulic or air-pressure test before being accepted as parts of more complicated machin-ery. Finally, there remains a comparatively small group of castings intended for uses of considerable responsibility where only the highest possible characteristics of the metal are acceptable, and for these specially cast test bars are required. The shape of the cast piece from which the test bar must be detached varies greatly from one country to another. The test bar as specified in the American Society for Testing Materials Specification B62-36 is widely used by the American foundry industry. The actual test piece is at the bottom of the cast block and has a riser about six times its mass. It is obvious that this test bar has an advantage over the actual casting. The latter rarely possesses a riser of as much as 30 per cent of its own weight and that riser cannot generally be located in so convenient a manner. Therefore, the characteristics of the test bar cannot possibly correspond to those of the casting itself. It must be taken into consideration that red brass if melted and cast in the best possible manner may show a tensile strength of 40,000 lb. per sq. in. with 35 per cent elongation in 2 in. Such a test bar would indicate that the metal was nearly perfect from the viewpoint of its gas and inclusion content. Barring some accidental defect, a casting cor-responding to such a test bar could be accepted as being quite sound. However, actual specifications do not demand such high characteristics; indeed, few specifications require over 30,000 lb. per sq. in. and 20 per cent elongation, while one Federal specification demands merely 27,000 lb. per sq. in. strength and 15 per cent elongation. It is obvious that

Jan 1, 1939

By P. B. Bucky

IN previous publications1 it was shown that a scalar model of any weighty structure, where the stresses produced are mainly due to gravita-tional forces, will behave similarly to its prototype if the model and proto-type material are the same arid the model is placed in a centrifugal field of force (substituted for the gravitational field) which has been increased in the same proportion as the linear model scale is decreased. This principle is now being applied to a study of the behavior of mine structures in an attempt to determine the laws that control them. The importance of using models as a means of solving mining problems has been discussed previously, yet it may be well to reiterate here that this method of research and type of solution have been productive of far-reaching results in other engineering fields, notably those of hydraulics and aerodynamics. Model research is a comparatively cheap and time-saving method of checking practical experience. Up to the present time the best guide to what will happen underground has been the judgment of the man who has observed most and been longest acquainted with the local conditions. His experimental work underground is limited by the elements of cost, time and danger, while failure is seldom permissible. In a model, as in a test tube, all elements that affect the solution of a problem are under definite control. Each element may be varied independently at will and its effects noted. Experimental work on a small-scale model may there¬fore be performed at a comparatively small expenditure of time and money, instead of on a full scale in the mine, where the cost, time, and danger elements are necessarily great. The experiments described in this paper are to be considered as part of a progress report and a continuation of Technical Paper 425. One object of the research program is to make each experiment point the way for further research on that particular phase of the general problem. The results and conclusions presented here are therefore not to be considered as final, but are to be interpreted as

Jan 1, 1933

By H. S. Bell

IT SEEMS unnecessary to dwell upon the advantages of the modern pipe still as compared with the older type of distillation equipment used by oil refiners. The relatively low installation cost, coupled with remarkable operating efficiencies of pipe stills, precludes the consideration of other types except in rare instances where some peculiarity of product or plant may have an influence. The question of the actual heat required to distil petroleum is quite involved. We have extensive data on the latent heats of the various hydrocarbons under different conditions of pressure. We also have information regarding the specific heats of various oils and the effect of temperature thereon. Because of the complexity of petroleum and of each fraction, it seems impossible to theoretically analyze the partial-pressure effect of the great number of hydrocarbons upon one another during distillation. If a distillation curve and percentage analysis of any crude or product are available, it is possible to construct a curve with ordinates representing per cent. distilled and B. t. u. per pound or per gallon, or other desired unit. To do so the crude is split into fractions, of 5 or 10 per cent. The boiling point and gravity of each fraction being determined, it is possible to evaluate the heat required. As each fraction is removed, the residue must be raised to a higher temperature and latent heat supplied for the successive fraction. As the calculations progress, the latent heats decrease while the specific heats increase. Such a curve is illustrated by Fig. 1 for a typical 39.9 B° North Texas crude.

Jan 1, 1928

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not with-stand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these require-ments, but as a result of the extensive research carried on by steel manu-facturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners&apos; requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator&apos;s problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935