Search Documents

By Lawrence A. Shepard, Richard H. Krock

A series of ductile, two phase W-Ni-Fe composites, sintered in the presence of a liquid phase, were tested in tension. Identical room temperature stress-strain curves were obtained for specimens containing from 80 to 92 wt pct W (58 to 75 vol pct W particles). The composites exhibited a maximum elongation of 29pct at room temperature, and 10.7 pct at 77 °K. The tungsten particles in the composite elongated by the same amount at these temperatures. Single-phase alloy specimens matching the composition of the composite matrix showed about one half the flow stress of the composites. The test results demonstrated that the mechanical properties of W-Ni-Fe composites are determined by the tungsten particles alone and are independent of matrix volume fraction or mean free path over the composition range studied. A general prediction of the plastic behavior of two-phase alloys or composites from a knowledge of the properties, size, shape, and dispersion of the individual components is not, at present, possible. The excellent theoretical and experimental exposition of the dispersion-strengthening problem applies only to cases where the stronger phase is present as fine particles and in volume fractions of a few percent. Materials in which the stronger phase constitutes a significant fraction of the volume, although of broad engineering interest, have received comparatively little analytical attention. This important group of materials is the concern of the present study. The degree of deformation of each phase during the plastic working of a ductile two-phase alloy has been established by Boas and Honeycombe,1 Clare-brough,2 and Clarebrough and berger.3 These workers empirically correlated the recrystallization temperature of the individual phases with the degree of cold work sustained by each. It was shown that the deformations of both phases are equal and therefore the same as that sustained by the composite whole when the volume fraction of the stronger phase exceeds 35 pct. At yielding, however, deformation begins in the weaker phase. A direct correlation of composite strength, as a function of deformation, with the strength of the individual components cannot be made. In the presence of stronger phase particles, the flow stress of the weaker matrix phase is enhanced by an additional hydrostatic component. The development and potential magnitude of matrix strength promotion upon straining has not even been experimentally established. Quantitative work in this field has been confined to ceramic-metal composites. These materials fracture at strains considerably below 1 pct by cracking of the ceramic particles.4-6 An indication of the potential constrained matrix strength capacity is given by the observation by Nishimatsu and Gur-land4 that the maximum tensile strength of a WC-Co composite is almost double the bulk strength of the cobalt matrix. The relationship between composite strength and geometry is ordinarily expressed in terms of the mean-free matrix path (referred to subsequently as MFP) between the stronger particles.* This factor takes into account both the volume fraction of matrix phase and the average size of the particles. unke17 concluded that composite strength varied directly with the decreasing log MFP, following the Gen-samer8 relationship. However, Gurland and ~radzil~ reported a strength maximum at an MFP of the order of 1 p in WC-Co composites. A ductile two phase metallic composite was chosen for the present investigation of composite mechanical properties with the view of avoiding the difficulties and ambiguities noted above. The W-Ni-Fe heavy alloy of Green, Jones, and pitkin9 contains 80 to 94 wt pct W, and nickel and iron in a weight ratio

Jan 1, 1963

By F. R. Hensel

THE absorption of oxygen by molten metals is a quick and convincing method to determine the metallurgical characteristics of various types of furnaces.1 The investigation was restricted to the use of coreless induction furnaces. A major variable in induction furnace practice is the frequency and its influence was studied by comparing melts made in a 5000-cycle and a 60-cycle induction furnace respectively.2 The authors are not aware that such a comparative study has been made before and therefore present this paper in the belief that the results will be of general interest. ANALYTICAL METHODS FOR DETERMINATION OF OXYGEN IN NICKEL An analytical procedure for determining NiO by a quick and simple, laboratory method has been worked out in collaboration with Dr. Herty, of the Pittsburgh Station of the Bureau of Mines. It was found that Dr. Herty's aluminum method as used for the. determination of FeO in iron and steel was very suitable for use with nickel if instead of hydrochloric acid a 10 per cent solution of nitric acid is used for bringing the metal into solution. Essentially this method involves deoxidizing the nickel-oxygen alloy with aluminum (2Al + 3NiO = Al203 + 3Ni) and determining the resulting Al203 by a residue analysis. The original oxygen content can then be calculated from the amount of Al-20,. The method as suggested by Dr. Herty3 is referred to in the present paper as method B. A slight modification of method Bled to the application of method A, a description of which is given below according to F. W. Beiter?:3

Jan 1, 1932

By H. Herman, M. E. Fine

Kinetics of reversion and reformation of GP I were studied resistometrically in Al-1.7 at. pct Cu. The reversion process is over in roughly 1/2 minute at 205 "C irrespective of the amount of primary aging. After reversion the occurrence of an incubation time before reaging begins has been substantiated. The reaging kinetics is drastically accelerated by plastic deformation to the specimen. An incubation time is observed only if the specimen is aged before reversion. The incubation time and the effect of plastic deformation indicate that nucleation of GP I is heterogeneous. Simple clusters of copper atoms apparently do not act as nuclei for GP I. AFTER quenching aluminum-rich copper from the solid solution range, Guinier-Preston zones of the first kind, GP I, form very rapidly at room temperature. The rate, largely controlled by the concentration of vacancies, is initially most rapid1 (that is, at the time of the first measurement: 1/2 min) and decreases with time. The nucleation is thought to be athermal. If after aging for several days the GP I is dissolved by reversion at 205°C, according to measurement of Young's modulus an incubation period is observed before GP I begins to form on subsequent aging.2 Yet if the reversion is carried out immediately after quenching, both resistivity3 and modulus changes2 show no incubation effect. The zones which form after reversion have the same structure as those which form after the quench.4 Because of entropy considerations and also the short diffusion time, the solid solution after reversion, 2 min at 205°C, is probably more highly clustered than at the original solution treating temperature, 520" to 550°C. It appears most reasonable to associate with nucleation the incubation time observed on reaging after reversion. A simple cluster of copper atoms, many of which are presumed to be present after reversion, is then not a sufficient nucleus for GP I; a GP I nucleus must contain something in addition to a cluster of copper atoms. The purpose of the present note is to give some additional experimental information concerning the incubation time and rates of reaging after reversion. The existence of the incubation time has been verified by measurement of another property, the electrical resistivity. Acceleration of reaging after reversion by plastic deformation has also been investigated. In acl.dition, the kinetics of the reversion process itself was studied. EXPERIMENTAL Electrical resistance was measured by the poten-tiometric four probe method. The 1.7 at. pct Cu alloy was furnished by the Aluminum Co. of America in the form of 1/2 in. rod. The major impurities reported by Alcoa were Fe (0.002 wt pct), Si (0.003 wt pct), and Mg (0.001 wt pct). Specimens for measuremenl of resistance were prepared by rolling to 0.010 in., cutting 2 by 0.2 in. pieces, rolling the middle pclrtions of these to 0.005 in., and splitting the 0.010 in. sections up to the reduced central section to form current and potential leads. Aluminum extension wires insulated with ceramic tubes were spot welded to the leads. The specimen was supported by the lead wires. The whole specimen assembly was annealed at 500" C in an air furnace for more than 12 hr and then aged at room temperature. This was done to assure quick and complete resolution during subsequent solution treatments. These were carried out in Houghton's "430 Temper Salt" at 520'C for 1 hr. Unless otherwise specified, quenching was accomplished by quickly transferring the specimen from a salt pot to 25°C water. Aging was carried out in a 3 liter dewar of distilled water, rotated and stirred. The temperature was controlled to +0.01°C with a thermomercurial regulator in conjunction with a transistorized relay

Jan 1, 1962

By Stanley W. Ivosevic

The South-Central Osa Peninsula produced around 30,000 kg (100,000 troy oz) of gold since prehistoric times. Gold freed by erosion from quartz lodes in the Mesozoic Nicoya ophiolite complex was reconcentrated through three generations of Quaternary sedimentary deposits. Resultant gold placers grade upward from 1 g/m3 (0.03 troy oz/m3) and are of moderate size.

Jan 1, 1980

By Y. C. Liu, R. H. Richman

From rolling textures of polycrystalline AgCl determined as a function of temperature, changes in the amounts of the individual textural components are correlated with temperature-dependent changes in glide geometry. The preferred orientations are influenced by the slip behavior as follows: 1) pencil glide, characterized by (110) slip directions and a greater participation in the deformation the higher the temperature, leads to a(012) fiber texture; 2) low-temperature deformation, primarily on (110) (110) systems, generates the {237}-(11, 9, 7) component; and 3) slip on {111}(110), comprising a significant portion of the room-temperature deformation, generates the {135}(211) and {110}(112) components. Typical re crystallization textures are also presented and briefly discussed. SPECIFIC relations between flow mechanisms in crystals and the individual orientations or components in deformation textures are necessary for a thorough understanding of the origin of such textures. Within each ordinary class of crystal struc- tures there is insufficient variety in the observed preferred orientations to permit direct and unambiguous correlation between flow mechanism and texture. A second approach to this problem is the correlation of textural changes with some known variation in glide geometry within one substance,1 In this paper, the latter approach is applied directly to a material in which there are distinct changes in the character of glide with changes in temperature. Silver chloride, although a nonmetal, is reported to exhibit slip,2,3 fiber textures,4 and rolling textures5,6 crystallographically similar to those of the well-studied fcc metals;7,8 in addition, there is a marked temperature sensitivity of the glide planes upon which flow occurs.3 Previous investigations of textures in AgCl unfortunately did not employ methods sufficiently sensitive to define possibly important minor components in the texture, nor did they utilize the temperature dependence of the glide systems. Thus, in order to clarify the effects of changes in slip mechanism, this paper reports a survey, using semiquantitative methods, of preferred orientations in rolled AgC1. Inasmuch as the influence of prior deformation texture upon preferred orientations after annealing is also of interest, some representative annealing textures are presented.

Jan 1, 1965

By W. R. McMillan, E. A. Gulbransen, K. F. Andrew

Annealed and electrolytically polished pure iron was oxidized between 650° and 850°C at oxygen pressures of 0.1 to 2 microns Hg. Electron optical studies showed that oxidation occurs discontinuously over the surface and orients crystallographically with the substructure of the metal grains. IN previous papers', " the authors described the formation of oxide films on high purity iron at norrnal pressures and at temperatures below 300°C. Electron optical studies showed that the oxide film consisted of many individual oxide crystallites having nearly random orientation on each metal grain. The size of the oxide crystallites depended upon the temperature and upon the extent of oxidation. In these studies the crystallite size varied from 250 to 1800Å. Recently, Bardolle and Benard3 studied the crystal habit of the oxide crystallites formed on Armco iron between 650" and 850°C in what might be defined as a "poor vacuum" atmosphere in which the pressure could be varied between 10-1 to 10-3 mm of Hg. Their results showed that, at 850°C and a vacuum of l0-2 to 10-3 mm of Hg, a few well oriented nuclei of oxide were formed on the metal grains. At pressures between l0-1 to 10-2 mm of Hg, many oriented nuclei of oxide were formed. At 750°C the metal surface was bright although an oxide was present. Unfortunately, the extent of oxidation, the oxygen pressure, and the influence of carbon in the metal were not determined, and it was, therefore, impossible to give a theoretical interpretation to the very beautiful light micrographs. Bardolle and Benard used the light microscope to determine the crystal habit of the oxide and X-ray diffraction to determine the orientation relationships. It was believed that the use of controlled amounts of oxidation at high temperature is an important method for the study of the initial stages of oxidation of metals at high temperatures. This paper presents the first results of an electron optical study of this problem for iron. Since the electron microscope and electron-diffraction methods using stripped oxide films and surface replicas yielded finer details of the crystal habit and structure of oxide film, these methods were used in this study. Two types of iron having different carbon contents were used: Puron and Armco* iron. A com- parison of the results for these materials made possible a study of the influence of the surface oxide-carbon reaction on the initial stages of oxidation. Before discussing the experimental results, the thermodynamic equilibria of 1—the oxidation reaction, 2—the surface oxide-carbon reaction, and 3—the solubility of oxygen in iron, will be considered. In addition, it is important to consider the kinetic-theory predictions on the rate of collision of oxygen with the iron surface. Thermodynamic and Kinetic-Theory Calculations Only one type of reaction is usually considered in the oxidation of iron at normal pressures at high temperatures: Fe(a) + 1/2O2(g) = FeO(s) 3Fe(a) + 2O2(g) = Fe3O4(s) 2Fe(a) +3/2O2(g) = a-Fe2O3(s). [11 However, two other reactions may occur: FeO(s) + C (solid solution in Fe) + Fe(a) + CO(g) [2] and Fe(a) + O2(g) e Fe(a) (solid solution of 0,). [ 3 ] In addition, iron will react with the higher oxide at certain temperatures to form FeO. For a complete interpretation of the oxidation of iron at low pres-

Jan 1, 1955

By William E. Ford, Edward Salisbury Dana

I. Oxides of Silicon. 11. Oxides of the Semi-Metals : Tellurium, Arsenic, Antimony, Bismuth ; also Molybdenum, Tungsten. III. Oxides of the Metals. The Fifth Class, that of the OXIDES, is subdivided into three sections, according to the positive element present. The oxides of the non-metal silicon are placed by themselves, but it will be noted that the compounds of the related element titanium are included with those of the metals proper. This last is made necessary by the fact that in one of its forms TiOz is isomorphous with MnOp and PbOz. A series of oxygen compounds which are properly to be viewed as salts, e.g., the species of the Spinel Group and a few others, are for convenience also included in this class.

Jan 1, 1922

By H. H. Taft

The mining possibilities of the volcanic area south of Bel-mont, Nye county, Nevada, have long been known. Some of the old-time prospectors knew that gold existed there. Its remoteness from any source of supplies, its long distances from water, the absence of game, and more, perhaps, the lack of grass for animals to subsist upon, has made this an unattractive region in which to search for mines. The decline of the Comstock mines, the exhaustion of sundry large and rich ore-bodies, the high cost of mining, marketing, and, particularly, the ruinously high freight-charges upon refractory ore that had to be shipped to distant smelters, have kept investors out of Nevada for the last few gears; and mining people have hardly yet awakened to the importance of To-nopah, Goldfield, and perhaps the newer and less developed districts. The discovery of Tonopah by J. L. Butler, who located the Mizpah claim in May, 1900, and the fortunes soon realized there, attracted many people. As the boom declined, many went away, some scattering out into the surrounding country, and the population is now about 7,000. In the fall of 1902 a discovery of gold was made 23 miles south, in what is now known as the Sandstorm group, 4 miles NW. of Goldfield. In the winter of 1903—4 the Combination, January and Florence mines were discovered, and shipments of high-grade ore soon followed. In January, 1905, there were 10,000 people in Gold-field. In June, 1904, rich gold-ore was found 85 miles SE., at the foot of the south end of the Kawich mountains, but this discovery was kept quiet until a re-location could be made. On August 10, 1904, the Bullfrog claims, and a month later the Ladd mountain and neighboring claims, were located. The Shoshone group was located September 24. This district is

Jan 1, 1907

By Harold R. Bradford

EXPANSION initiated during and after the war has placed industrial plants in new areas and increased reduction and manufacturing facilities in communities already established. With added expansion interest has grown in possible area contamination from waste products. Evolved flue waste contains many chemical contaminants that may or may not cause concern; however, atmospheric pollution has always been a problem to industrial communities. For some time effects attributed to small quantities of compounds of fluorine in various waste gases have been studied by industrial, medical, agricultural, and associated interests.1'2 Aside from an article by Churchill, Rowley, and Martin in 1948," little has been published on the subject of fluorine in coal except by foreign investigators. The first indication of fluorine compounds in coal was noted in England in 1934 by R. Lessing,4,5 who found that the presence of fluorine in Midland and West County coals was definitely established by etching of glass and by severe corrosion of porcelain fillings in a gas works scrubber. Etching of glass in a direct contact annealing kiln initiated research, and in 1944 four papers were published by H. E. Crossley,6-9 giving results of investigations of fluorine in coal of England by the Fuel Research Board, Department of Scientific and Industrial Research. These investigations studied methods of determining fluorine, the quantities present in various coal deposits, the geographical distribution of fluorine in British coals, occurrence of fluorine in minerals associated with coal, amounts of fluorine compared to other constituents of coal, the nature of fluorine compounds, and industrial significance of fluorine in coal. It was shown that British coals contain from 5 to 200 ppm of fluorine, which is probably present as fluorapatite [Ca10F2(PO4)6], often written as [3Ca3P2O8.CaF2]. The fluorapatite is intimately associated with shale in some coals and can often be separated from these coals along with the shales. H. E. Crossley8 also reported no correlation between the amounts of chlorine, sulfur, or ash and the amount of fluorine in different coals. He found, however, a relationship between the content of fluorine and phosporus in many British coals. Thus it should be possible to anticipate likely fluorine-rich coals from existing data giving phosphorus content. Behavior of the fluorine compounds of coal was compared with that of 12 fluoride-phosphate minerals in sink-float separations and solvent ex-

Jan 1, 1958

By R. H. Jamison

A relatively new haulage system is described. Employed by the Delmant Fuel Co.. the "Full Dimension" system provides an uninterrupted flow of coal from a loader or continuous miner at the face to the main line transportation system. This system is said to provide a higher percentage of recovery as well as additional safety and production. Delmont Fuel Co. is employing a comparatively new system of transportation known as a Full Dimension system. Cne of these systems has been in operation for a year at the company's 10-B Mine as a part of a conventional section. A second was installed at the No. 10 mine in late 1960 to handle the production of a Colmol in a pillar section. SYSTEM COMPONENTS A Full Dimension system is a haulage system that provides an uninterrupted flow of coal from a loader or continuous miner at the face to the main line transportation system. The equipment required for this system consists of a series of interconnected chain conveyors that are mobile and articulated. They will retract or extend a sufficient distance for the development of a five-entry system; or, in the Colmol pillar section, it provides reach of 210 ft in all directions from the section belt. The components of this system are: l)One 160-ft chain line placed in tandem with the belt conveyor. It has a self-propelled drive, is 20 in. wide and 9 in. deep. Moving this conveyor requires the assistance of a loading machine or cutting machine. 2) One 40-ft piggyback that discharges along the entire length of the 160 ft chain conveyor. 3) A mobile bridge carrier, which is a self-propelled conveyor with four wheel steer and four wheel drive, twenty-eight feet long, it delivers coal to the receiving end of the piggyback. Axles steer individually making possible almost lateral movement. 4) Another 40-ft piggyback, duplicate of item 2 that delivers coal along the entire length of item 3 (mobile bridge carrier). 5) A second mobile bridge carrier, similar to the first, which deliver coal to the piggyback (item 4). 6) A third 40-ft piggyback, duplicate of items 2 and 4. This pig is attached to the loading machine and delivers its coal along the length of the second mobile bridge conveyor. Since the original preparation of this paper, the Delmot Fuel Co. has been able to eliminate the 160-ft chain conveyor. This was accomplished by connecting the outby piggyback directly to a loading machine with an extended boom. The loading machine loads directly onto the belt. This change has resulted in a substantial reduction in moving time and greatly increased flexability. A single trailing cable powers the entire string of equipment. It is attached to the side of the equipment in such a way as to keep it off the ground and afford maximum protection. The tramming rate of this equipment is 90 fpm. The conveyor capacity in a conventional section at Delmont's mines is 7.5 tpm and in the Colmol section is 5.5 tpm. This regulation is a simple function of conveyor speed. To visualize operation of this equipment, it would be well for me to touch briefly on local conditions in the Upper Freeport seam in which we mine. (Also, see the photographs of some of the equipment in use.) DELMONT'S TOPOGRAPHY The Delmont Fuel Co. operates two mines in this seam in Westmoreland County, Pa. The No. 10 mine, which was opened in about 1912, is now almost worked out. Depending on economics in the industry, it has a life of two to four years on a declining production basis. A year ago a new drift mine was opened which is called No. 10-B. It is about two miles from the cleaning plant and is connected thereto by an overland belt conveyor. The new mine is being developed at a rate calculated to take up the slack as the old mine plays out. The Upper Freeport seam averages 4.2 ft in thickness in the area of the Delmont mines. It carries 4 in. of boney coal at the top of the seam and a middle man of from 2 to 4 in. We mine just above a 1-in. slate parting which has 4 to 6 in. of highly laminated coal beneath it. This material normally makes a very firm bottom. The roof varies from dark shale to sand rock and 36-in. bolts are placed on 4-ft centers for roof support. All working places are driven 20 ft wide on development and 25 ft wide on retreat. Selection of mobile chain conveyor equipment when it became available, was a very natural move for Delmont Fuel to make, because chain conveyors and piggybacks had been in use at the company's mines for about 12 years. Grades in the new mine

Jan 1, 1961

By B. W. Gonser, C. M. Heath

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By C. M. Heath, B. W. Gonser

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By Marston G. Fleming

CRITICAL pH has been defined by Wark1 as that pH value below which a mineral will float and above which it will not float in solutions containing a given concentration of collector but free from other depressants or activators. - The relationship between mineral, collector concentration, and pH is expressed in the form of a critical pH curve determined by the captive bubble method and is generally regarded as being fundamental to the system involved. The mechanism of alkali depression is currently in dispute, two general theories having received authoritative support. The view expressed in Taggart's chemical theory of flotation2 is that in the presence of a critical concentration of hydroxyl ions, all the metal ions available at the surface of the mineral are present as anions of the form [M (OH)x]-y. The formation of the necessary metal xanthate is thus precluded and, furthermore, any metal xanthate coating previously formed, at a lower pH, will be dissolved. Gaudin3,4 and the Melbourne school under Ware hold that alkali depression is caused by the preferential adsorption of hydroxyl ions by the mineral surfaces. This paper describes an investigation of the mechanism of alkali depression in each of the three systems: cerussite-aqueous carbonate-xanthate, cerussite-xanthate, and galena-xanthate. Alkali Depression of Cerussite by Control of Carbonate Ion Concentration Wark and Cox6 have shown that in the presence of Na2CO3 a higher concentration of xanthate is required to effect bubble contact with a cerussite surface than in carbonate-free solutions. To examine this depression of cerussite by sodium carbonate, a series of captive bubble tests was carried out on cerussite specimens in solutions containing 100 mg per liter of potassium ethyl xanthate and varying concentrations of sodium carbonate. The pH was adjusted by the addition of dilute hydrochloric acid. For purposes of comparison a standard critical pH curve was determined for cerussite with potassium ethyl xanthate in solutions containing no added carbonate. In the latter case pH adjustment was made with sodium hydroxide. The experimental method employed in both series was broadly similar to that described by Wark and Cox;7-9 a number of refinements suggested by Sutherland10 were adopted, and the procedure was further developed and modified to suit the particular requirements of the investigation. The relationship between pH and the concentration of potassium ethyl xanthate necessary to induce bubble contact at cerussite surfaces is shown in Fig. 1. The relationship between pH and the concentra- [ ] tion of sodium carbonate necessary to prevent bubble contact at cerussite surfaces in the presence of 100 mg per liter of potassium ethyl xanthate is shown in Fig. 2. Comparison of the. two curves shows that at a collector concentration of 100 mg

Jan 1, 1952

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. [t] About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5.800,000 bbl. of cement. Following are some of the cement require¬ments of the Shasta Dam specifications: [PER CEN'I Chemical composition: Loss in ignition2.25 Insoluble residue0.75 S032.25 M905.00 Uncombined lime in clinker (CaO)T.25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 35 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 6,5 Tricalcium aluminate (3CaO.Al203)Not more than 7 Tetracalcium aluminoferrite (4CaO.A1203.Fe203) Not more than 20 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following: [ ]

Jan 1, 1941

By R. J. Wasilewski

Axial expansion has been determined by X-ray diffraction up to 600° to 760°C in a titanium and four high-oxygen alloys. Expansion data cannot be fitted to the usual quadratic expression and anomalies observed are believed indicative of the changes in the bonding configuration of the valence electrons. Furthermore, there is significant disagreement between data obtained on poly crystalline and single crystal powder specimens. The major disagreement occurs within the temperature range (-470°C) where both mechanical and electrical properties also show markedly anomalous behavior. X. HIS work forms part of an investigation of physical properties of pure titanium and its osolid solutiono alloys with oxygen and nitrogen. In view of the anomalies observed in both the electrical resistivity' and the susceptibility behavior it was decided accurately to determine the thermal expansion behavior of the pure and alloyed a titanium. PREVIOUS WORK The axial expansion coefficients reported for pure titanium are listed below. As can be seen, there is a marked discrepancy between the axial expansion and the experimentally determined coefficients on poly crystal line material. Thus, if we take the most recently reported axial expansivities3,4 we obtain perature interval of 25o to 700°C. The experimental value reported for polycrystalline metal is, however, of the order of 9.7 x 10o6 per OC. EXPERIMENTAL I) Pure Titanium. High purity titanium powder of -325 mesh was used throughout most of this work. The only significant impurities present were the interstitials, oxygen and nitrogen, which analyzed respectively 650 and 80 ppm. The purity of the ma-

Jan 1, 1962

THE John Fritz Medal Board of Award, at its regu¬lar annual meeting Oct. 19, awarded its gold medal to Herbert Clark Hoover. Thus ended a process of selection begun a few years ago. The award was tentatively made a year ago by the Board, which is composed of sixteen recent past-presidents of the four national societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers, having together a membership of nearly 60,000. The sixteen members of the Board are: American Society of Civil Engineers : C. E. Grunsky, Robert Ridgway, George S. Davison and John F. Stevens ; American Institute of Mining and Metallurgical Engineers: William Kelly, J. V. W. Reynders, Samuel A. Taylor and E. DeGolyer; American Society of Mechanical Engineers: Fred R. Low, D. S. Jacobus, Dexter S. Kimball and Charles M. Schwab; American Institute of Electrical Engineers: Farley Osgood, M. I. Pupin, C. C. Chesney and Bancroft Gherardi.

Jan 1, 1928

By F. V. Lenel, G. S. Ansell

The creep behavior of an aluminum -aluminum oxide alloy, A T 400, fabricated by compacting an atomized aluminum powder, extruding the compact, cold working, and recrystallizing the extrusion, was investigated. This alloy has a dispersion spacing of 1 . Previously Ansell and Weertman determined the steady-state creep rate of a recrystallized aluminum-aluminum oxide SAP-type alloy, MD 2100, with a 0.48-p dispersion. This alloy was found to have a steady-state creep rate of less than 10-6 min-1, too small to be measured accurately. By employing a more sensitive method of measuring creep rate, it was possible to determine the steady-state creep rate of AT 400 alloy, which is somewhat faster than that of MD 2100, at a series of temperature and applied stresses. Above a stress of Burger's vector, A = dispersion spacing, u = is a shear modulus) the rate follms an equation of the type: Steady-state creep rate K = A exp. where A is a constant, Q is the activation energy for sey-diffusion, and is the applied stress. At stresses lower than the steady-state creep rate drops off sharply and is no longer in agreement with this equation. This behavior is in good agreement with that predicted by the model for dispersion strengthened alloys in the stress and temperature range investigated. The absolute value of the creep rate is, however, four orders of magnitude lower than that predicted if the normal number of active dislocation sources are assumed to be present. It is concluded that in this SAP-type alloy the usual three-dimensional dislocation network is not present. Instead, short dislocation segments extending from one dispersed particle and terminating at a neighboring particle may act as dislocation sources. With this provision the creep model proposed by Ansell and Weertman reasonably accounts for the creep behavior which was observed. RECENTLY, Ansell and Weertman1 proposed a dislocation model from which they derived creep equations to describe the steady-state creep behavior of dispersion - strengthened alloys. Following Schoeck,2 they assumed that the rate controlling process for steady-state creep is the climb of dislocations over the dispersed particles. In order to verify their creep model, Ansell and Weertman determined the steady-state creep behavior of an aluminum-aluminum oxide SAP-type alloy, MD-2100, in both the fine-grained as-extruded, and coarse-grained recrystallized conditions. Since the grain size was the order of the dispersion-spacing, their model was not applicable for the as-ex- truded alloy. It should, however, be applicable to the coarse-grained recrystallized alloy. The results they obtained were rather unexpected. No meas-ureable steady-state creep was observed for the recrystallized MD-2100 alloy. If their model is correct, and if the second-phase particles act solely to hinder dislocation motion, then some measureable steady-state creep would have been expected. On this basis, they postulated that, in this SAP-type alloy, the main effect of the fine dispersion was to inactivate dislocation sources rather than to hinder the movement of dislocations. In order to understand more fully this unusual creep behavior, and to determine the validity of the model proposed,' the steady-state creep behavior of an aluminum-aluminum oxide recrystallized SAP-type alloy, with a somewhat coarser dispersion spacing, was investigated. The results of this study are presented in this paper.

Jan 1, 1962

INTRODUCTION Trade financing is a particularly important component of short-term financing for a minerals company since errors, extra costs, or payment delays/defaults can easily wipe out the profit margin on a particular shipment or can cause problems when arranging purchases of e.g. reagents. It is required to make any minerals operation function and does not have to be cross-border to require proper management. Sources of working capital are as follows: 1. Extended credit terms from suppliers 2. Inventory loans from banks, finance companies 3. Accounts receivable financing or factoring 4. Credit lines or overdraft facilities from banks. TRADE CREDITS These are provided under the familiar terms "net 10 days" or payment due by the "10th day of the following month." Thirty days for payment is usual but longer periods can be negotiated with regular suppliers. Shipment may be made on open account with specified periods for settlement. In the mining industry, a custom smelter gains trade credit by paying for concentrates three months after the month of shipment. INVENTORY LOANS Various forms of inventory finance are provided via "floor-plan" or warehouse financing. A set percentage, usually 60%-80%, of a good-quality, readily saleable inventory item (e.g. bullion, concentrates, ingots) will be provided by a bank or finance company which will usually have security over these products and has a right to inspect the goods from time to time. Legal security will he achieved by warehouse receipts, floating liens, chattel mortgages, trust receipts, or through collateral management service companies. The latter certify control over stock or distribution outlets and often carry insurance against fraud. Costs range around 1.5% - 2.0% p.a. or more plus some fees to cover out-of-pockets or other costs. ACCOUNTS RECEIVABLES Accounts receivable financing is based on the company's generation of satisfactory receivables which are continuously assigned to a bank or finance company ("factoring"). Because of the risks in being able to collect receivables, such as payments to a smelter for its blister copper shipments to a refinery, this form of financing costs as much as 3% - 5% of the debt amount purchased plus an additional charge for processing paperwork. Receivables can be purchased with or without recourse and on a notification or non-notification basis to the client's customer to, respectively, pay the invoice directly to the bank or not. LETTERS OF CREDIT Letters of Credit ("L/C's") are a common feature of international trade finance whereby a bank, at the request of the buyer, issues a written undertaking to an exporter to pay a specified sum of money within a set time on presentation of previously specified documents. This undertaking means that the exporter is no longer relying on the credit standing and integrity of the foreign importer. A dispute about shipment does not otherwise affect the obligation to pay upon presentation of a "clean" set of documents. These documents include the hill of lading and other documentation, often on standard "form" bases. There are a number of conventions and techniques in L/C's such as irrevocable/revocable L/C's, time L/C's, confirmation/advising L/C's and transferable L/C's. These are tools to adjust for the varying risks that the importer will not pay. Other routes where one is comfortable with an importer include documentary sight hills (D/P hill), documentary term bills (D/A bill), and, of course, open account.

Jan 1, 1985

By A. E. Gorum, J. Washburn, E. R. Parker

Experimental evidence was obtained in support of the idea that cleavage fracture can be initiated by dislocation pile-up. The high ductility of MgO crystals when tested in bending comPared to their relative brittleness in tension was explained on the basis that large pile-ups are more likely in a tension specimen. CLEAVAGE fractures have been a problem of major concern for many years. A number of large steel structures have failed in a brittle manner, usually suddenly and without warning; often the failures occurred for no obvious reason and at nominal stress levels well within the generally accepted range. A great deal of data have been collected about factors that contribute to failures,1 but the physics of the fracture process has never been revealed. cottrel12 has recently developed a theory of brittle fracture in ductile materials which was based upon the concept that dislocations moving on two intersecting planes can unite to form a crack nucleus. This theory accounts for the known effect of grain size and for the effect of testing temperature. There has, as yet, been no experimental evidence published that would substantiate this or the earlier theories based on stress concentrations due to piled-up dislocations. The study reported herein was conducted to obtain information that would either substantiate or disprove the

Jan 1, 1960

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929