Search Documents

By Donald Warren, J. F. Libsch

HIS investigation originated as a result of a pre-vious experimental study' of the magnetic properties of Fe-Co alloys fabricated by the powder metallurgy technique. Densities of powder compacts prepared for the magnetics investigation varied from 7.45 to 7.70 g per cu cm or from 93 to 95 pct of the experimental value of 8.08 g per cu cm for a fused alloy of the same composition.' While this range of density is considered sufficiently high for most applications, the highest possible density is to be desired for maximum magnetic properties. By applying a technique similar to the one described above to a pure electrolytic iron powder, Rostoker³ was able to achieve a density of 7.895 g per cu cm, which is the highest density ever reported for sintered iron. While Rostoker's work involved the sintering of an elemental powder rather than a mixture, it was believed that higher densities should also have been obtained for alloys using the above technique because of the recoining operation and the high sintering temperature. Consequently, it was decided to investigate the various factors affecting the density of this alloy with the idea that such a study might lead to higher densities and, as a result, powder alloys having magnetic properties identical with those of the fused alloys. It was believed that the principal reason that near-theoretical densities for the powdered alloy were not obtained was the interference of gases with the normal sintering mechanism. When present during the sintering operation, gases can exert several harmful effects: they can remain on the particle surface and interfere with surface diffusion and plastic flow; they can be released and, under certain conditions, expand the void spaces through gas pressure; or they can remain trapped in the pores and exert a hydrostatic pressure that retards elimination of the pores. Jones,4 Rhines,5 Goetzel," and others have given the effect of gases in the sintering of powder compacts an extensive treatment. Among the more important sources of gases in the sintering process are dissolved gases, adsorbed gases, air entrapped during pressing, and gaseous products of chemical reactions. During sintering adsorbed gases are partly released at a relatively low temperature, while those gases entrapped during pressing cannot escape until their pressure is increased sufficiently through increasing temperature to expand the interpartjcle openings. The remaining adsorbed gases, gaseous reduction products, and dissolved gases produce a similar effect at the higher temperatures. If, in the sintering process, gas evolution occurs after the interpore channels have been sealed, an exaggerated expansion of the void spaces results. This is particularly true if the temperature is high enough for extensive plastic flow. In his fabrication of powder bars from tantalum, Balke7 had to consider the effect of adsorbed hydrogen and provide for its escape during sintering by limiting the compacting pressure to a maximum of 50 tons per sq in. The effect of gases entrapped during pressing was first noted by Trzebiatowski8 when he found that gold and silver powders decrease in density with increasing sintering temperature if pressed at 200 tsi, while they exhibit the usual increase when pressed at 40 tsi. Recent investigators9-11 have also noted that entrapped gases have an effect on the expansion of copper compacts during sintering. Proper provision for the escape of gaseous products of reduction must be made in order to avoid deleterious effects. Myers" states that in the sintering of electrolytic tantalum powder, the temperature was gradually raised to 2600°F with a pause at 2000°F to permit reduction of the oxides. Experimental Details For the present study, 50 pct Co-50 pct Fe compacts in the form of circular disks 1½ in. in diam and 0.15 in. thick were fabricated by the pressing and sintering of a mixture of the elemental powders. It was decided to follow the sintering process by means of liquid permeability measurements, because it was thought that such measurements might serve as a measure of relative pore sizes, as well as a possible indication of the point at which most of the interpore channels become sealed. However, since the permeability as measured by the flow of a liquid, such as ethylene glycol, does not give an absolute indication of the point where the pores have become isolated, a method for determining the percentage of pores connected to the surface was set up. As an additional cross check on the permeability measurements, metallographic methods were used to study the relative pore size. Finally, the property of ultimate interest, the density, was measured. Raw Materials: The powders used consisted of an annealed, 99.9 pct pure, —150 mesh grade of electrolytic iron powder, and a 98 pct pure, —200 mesh grade of reduced and comminuted cobalt powder. The cobalt powder was not further processed either by hydrogen reduction or annealing. The screen analyses for the iron and cobalt powders are given in Table I, while the chemical analyses for each type of powder are listed in Table 11. Table 111 gives the hydrogen loss measurements for the powders according to the M.P.A. Standard Method and for a higher temperature as well. Preparation of Compacts: Equal amounts of the elemental powders were mixed by rotation for 1 hr and then pressed into compacts approximately 0.15

Jan 1, 1952

Jan 1, 1928

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RIVHARD W HUNT 1883

Jan 1, 1910

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RIVHARD W HUNT 1883

Jan 1, 1910

By Fred R. Harris

INTRODUCTION MacMillan Tungsten is located in northwestern Canada on the border of Yukon and Northwest Territories at a latitude of 63º17' and altitude of 1800 m above sea level. The deposit lies within the Selwyn Mountains 10 km from the Canol Road. It is 660 km by road from Whitehorse, Yukon, and 1325 km by air from Vancouver, British Columbia. MacMil lan Tungsten is a contact metasomatic deposit in gently dipping Lower Paleozoic limestone and limestone breccia adjacent to a Cretaceous quartz monzonite stock. Four tabular tungsten skarn horizons contain total geological reserves of 30 million tons grading 0.9% WO3. DISCOVERY AND HISTORY J.F. Allan, a former AMAX geologist, located mineral claims in September, 1962, to cover the source of scheelite-bearing skarn float found in the headwaters of Cirque Lake Valley. Exploration work on the property conducted mainly between 1968 and 1973, includes geological mapping, 10,500 m of diamond drilling in 73 holes, and 735 m of underground exploration. Mil 1 tests were carried out on a 300 ton bulk sample obtained underground. Preliminary feasibility studies, collection of weather data and a variety of environment studies have been carried out since 1973. Although no production date has been set MacMillan Tungsten will undoubtedly be a major tungsten producer.

Jan 1, 1976

By E. Gybbon Spilsbury

In the course of the persistent and rapid advance of our country towards the goal she has set for herself, of commercial and manufacturing supremacy, there stand out certain periods or cycles of prosperity or depression, succeeding one another with a comparative regularity as to their ultimate trend, but of varying lengths and intensities. I might compare this course to that of a railroad between two points at different levels, with intervening mountain ranges and valleys, the up-grades climbing towards the final upper terminal of prosperity, while the down-grades retard the ascent, and tend to return to the valleys below. Just at the present time we are evidently at the bottom of one of these valleys, and, before starting to climb the next divide, it may be prudent for us to look into the condition of our rolling-stock, and especially into that of our brakes, and see what the experience of our downward journey has taught us, and whether we are properly equipped for the new upward advance which now lies before us. Probably no previous period of the same duration has produced in all branches of mining and metallurgy improvements SO many and so various as have the last ten or twelve years. Not that they have brought forth any such startling and revo-

Jan 1, 1898

By E. A. H. Tays

As I promised, in a former paper on the Bryan Mill,* to give further data regarding the plates from four battery-aprons, I now submit the following: These aprons were 4.5 feet wide by 16 feet long; the first two plates of each apron were 4.5 by 4.5 feet, and the remainder of varying sizes, as can be seen by their relative weights, as shown in the table; but all were 54 inches wide. They were in use 4 years and 9 months, and about 15,265 tons of ore passed over each. The ore was quartz, carrying about the same weight in silver as in gold; showing some copper, and highly impregnated with ferric oxide. The tailings show about 0.6 per cent., and the bullion about 10 per cent., of copper. The silver was present mostly as sulphide; and the copper was also present as sulphide, with some carbonate. The ore treated ill 1898 was a fair average of the whole run; so I take it as an example from which to make a few deductions.

Jan 1, 1901

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

By D. L. Kelley

High-viscosity water injection has been proposed for use in reservoirs containing high-viscosity crude oils. Previous publications have largely ignored the possible effects of the connate water on the proposed process. This paper describes experimental work which indicates that the connate water will be forced ahead of the injected water to form a bank of low-viscosity water. This decreases the oil recovery which would be expected if such a bank were not formed. These effects are shown for a range of fluid mobilities and connate-water saturations for a five-spot injection system. In general, oil recoveries using viscous water are significantly greater than for untreated water even though they are less than would be expected if no connate water bank were formed. INTRODUCTION The effect of mobility ratio on the oil recovery of wa-terfloods has been known for many years. Muskat first pointed out that the fluid mobilities (k/µ) in the oil and water regions would affect the performance of the water-flood, and he estimated the general effect of these variables.' Since this early work, studies of the effect of mobility ratio on secondary recovery have been reported where mathematical,' potentiometric3 and scaled flow models' were used. These studies have shown that a reduction in the mobility ratio between the oil and the displacing fluid would cause additional oil recovery when water-flooding reservoirs containing viscous crude oils. Studies reported by Pye- nd Sandiford 8 have indicated that chemicals to increase injection water viscosity are now available and can be used to reduce the over-all mobility ratio of a waterflood. Where mobility ratios are controlled by the injection of viscous fluids, the connate water of the reservoir can play an important part in the displacement of the reservoir oil. The purpose of this study was to determine the effect of the connate-water saturation in waterfloods where viscous waters are used for injection. DISPLACEMENT OF THE CONNATE WATER Russell, Morgan and Muskat7 were the first to recognize the mobility of connate waters in waterflooding. They conducted waterfloods on oil-saturated cores containing 20 and 35 per cent irreducible water saturations, and found that from 80 to 90 per cent of the "irreducible" water was produced after only one pore volume of water was injected. However, their experiments were conducted at rates of flow significantly higher than those ordinarily occurring in waterfloods. Also, the cores were only from 4.0 to 8.5 cm long. Brown 4 studied a 100-cm linear sand pack which had been prepared to contain connate water and oil. He used 140- and 1.8-cp oils with injection water of essentially the same viscosity as the connate water. He found that all of the connate water was displaced by the injection water in both cases. However, the injection volumes required for complete displacement of the connate water were considerably higher in the case of the more viscous oil. To verify the results of the foregoing experiment, a 10-ft-long linear model was constructed by packing 250-300 mesh sand in a 1/2-in. diameter nylon tube. The model was evacuated, saturated with a brine of 1-cp viscosity, and flooded with a 41-cp mineral oil to the irreducible water saturation of 10.9 per cent. The model was then waterflooded by the injection of a water solution which had an apparent viscosity of 42.6 cp. The solution consisted of 0.5 per cent methylcellulose in distilled water. The viscosities of the oil and connate water were measured with an Ostwald viscosimeter. The viscosity of the polymer solution was calculated by Darcy's law using pressures measured during actual flow conditions. The ratio of the mobility in the oil region to the mobility in the inject ion-water region was approximately 0.32. The mobility ratio of the oil region to the connate-water bank was approximately 14. The mobility ratio between the connate-water bank and the injection water region was 0.024. Approximately 84.5 per cent of the recoverable oil was produced before water breakthrough. Immediately following breakthrough, oil and connate water were produced at an increasing water-oil ratio until the viscous injection water broke through. At viscous-water breakthrough, 96 per cent of the original connate water had been produced. After breakthrough of the viscous water, there was no additional production of connate water or oil. The near-

Jan 1, 1967

AIME Committee on Local Section Affairs Joseph L Gillson, Chairman J C Kinnear, Jr Lloyd E Elkins AIME Committee on Student Chapter Affairs (Special Committee, pending Bylaw revision) R F Mehl, Chairman E H Crabtree, Jr John C Calhoun, Jr

Jan 1, 1958

By D. E. Hartman, J. M. Roberts

A detailed study of the temperature dependence of the critical stress, TB . necessary to cause a damping loss of 1.41 x 10-6 g mm per mm3 in pre-strained magnesium single crystals has been carried out in the temperature range 82" to 320°K. Tb is found to be linearly related to the reciprocal of the ahsol~cte temperature in this temperature range. The temperature dependence of the anelastic limit, TA, defined as the stress necessary to form open unidirectional stress-cycle damping loops has been measured between 82" to 320°K. ta is found to be independent of temperature in this range. It is suggested that TA is determined by the stress necessary to activate Frank-Read dislocation NUMEROUS studies1-9 have been reported concerning the details of yielding and microstrain near and below the generally discussed macroscopic flow stress. The work of Kramer and coworkers10-13 is helpful in determining certain qualitative facts. concerning preyield phenomena. The absence of a stress-dependent delay time in annealed copper and aluminum single crystals between 83" and 298 suggests that the preyield mechanism is temperature-independent in this range. This is not sources. The temperature and stress dependence of the effective activation volume (Veff) has been measured in the damping-loop region in prestrained magnesium single crystals. The data suggests that Veff/kT is approximately constant, equal to 2 4.5 sq mm per g in the temperature range 130°to 298°K, and that Veff is almost independent of stress at stress levels greater than 10 g per sq mm. A restricted model is developed to predict the stress (rb) necessary to cause a small fixed damping loss as a function of temperature, effective activation volume, and dislocation density. Various possible dislocation mechanisms controlling TB are discussed. true for zinc, p brass, and iron crystals in the same temperature range, however, since the existence of a stress-dependent delay time suggests a thermally activated preyield mechanism in these materials.10-13 The work by Vreeland et a1.14 confirms the work by Liu et al.ll on delayed yielding in zinc single crystals. A stress-dependent delay time between 82" and 298°K was found12 in prestrained aluminum and copper crystals. These results suggest that the preyield phenomena may be different between prestrained and unstrained or annealed crystals. The temperature dependence of the yield point at 2 x 10-8 plastic strain found by Rosenfield and Averbach3 in annealed copper and aluminum is not in agreement with the delay-time data, unless possibly the delayed yielding experiment only de-

Jan 1, 1964

By R. Priestner, R. F. Krause

Solid, cylindrical crystals of a iron have been fractured at 10°K by the simultaneous application of tension and torsion stresses. Thus, a complex distribution of normal (sN) and shear (ss) stresses existed in a cleavage plane at fracture. In every crystal the clearage-plane normal was inclined to the specimen axis, so that a unique point, M*, in the operative cleavage plane was defined where the quantities sn and s2 N + s2 S) were maximized. It is shown that the maxirrzum resolved normal stress on the cleavage plane at fracture decreased as the resolved shear stress in the cleavage plane at M* increased. Thus, a normal stress la?*! for fracture was not satisfied. A fracture law which takes shear stress into account. and which predicts that (s2 N +s2S) should be constant, is to be preferred. However, the data is best represented by a linear dependence of sN on sS, sS which 110 physical significance can be attached. It is suggested that the fracture-nucleating -mechanism is a short-range one. A critical stress law has not yet been unequivocally established for the propagation of cracks in metals. Measurements of the tensile fracture stresses of variously oriented zinc single crystals1 failed to establish the normal stress law expressed by In Eq. [1], sN is the fracture stress, P, resolved normal to the fracture plane, and 0 is the angle between the fracture -plane normal and the stress axis. Similarly, a comprehensive investigation failed to verify the normal stress law for the tensile fracture of a-iron single crystals.' However, a subsequent investigation,3 using iron from the same ingot, presented fracture data which obeyed the normal stress law. It has been shown previously4,5 that the Griffith criterion for fracture6 does not predict such a normal stress law. This result is of particular significance in considering the fracture of metals, such as zinc and iron, which may fail by cleavage. In these metals fracture propagates in a well-defined "cleavage" plane, whether or not an applied stress is normal to it. When the cleavage-plane normal deviates from the direction of application of a uniaxial stress, for example, the crack propagates under the combined action of normal (sN) and shear (ss) stresses. When the presence of a resolved shear stress in the crack plane is taken into account, the Griffith criterion is expressed by4

Jan 1, 1967

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1917

By M. A. Jones

Performance of a pilot flood in eastern Kansas indicates improved recovery and accelerated production resulting from mobility ratio control obtained by adding a high moleculur weight polymer to injected water. Ultimate pilot flood recovery of the 75-cp reservoir oil is anticipated to he 350 bbllacre-ft during the six-year flood life. Cumulative recovery to date totals 242 bbl/acre-ft after 30 months of injection. Reservoir parameters and flood performance are disc~rssed in detail to provide a case history relating to the feasibility of polymer flooding. INTRODUCTION The Vernon Polymer flood of the Brazos Oil & Gas Co., located in Sec. 2, 24 S., 16 E., Woodson County, Kans., was begun in late Oct., 1963. Injection of a 500 ppm solution of Pusher* polymer was initiated in a 15-acre pilot to determine feasibility of improving oil recovery by mobility ratio control. Performance to date and the anticipated recovery of 115,000 bbl from the 329 acre-ft pilot indicate efficient displacement of the viscous reservoir oil. Dependence of flood recovery on the displacing fluid-displaced oil mobility ratio has long been recognized. Displacement efficiency of the reservoir oil decreases with increasing mobility ratio. Therefore, economic reduction of this parameter is an attractive approach to improving oil recovery. particularly from viscous oil reservoirs where mobility ratios are often quite high. Waterflood mobility ratios can be controlled by dilute solutions of certain polymers'; which provide a displacing fluid with considerably reduced mobility. Reservoir parameters and flood performance are emphasized in this paper to provide data relating to polymer flood applicability. THEORY The polymer used in the Vernon pilot exhibits the property of unusually high resistance to flow through porous media.'.' A small concentration in injected water effects a mobility reduction considerably beyond that predicted from increases in bulk viscosity as measured in a capillary or rotating cup viscosimeter. Water mobility in the subject flood is reduced by a factor of 7.55 with the addition of 500 ppm Pusher chemical to injected water while the bulk viscosity is increased from 1.03 to only 1.40 cp at 75F. The exact flow mechanism causing resistance to flow has not been established; however, it is observed only in tortuous flow systems and appears to be influenced by brine properties, rock properties and oil saturation. Consequently, mobility reduction is estimated from flow studies for a given sample of reservoir rock and is expressed in terms of a "resistance factor".' This parameter is defined as the ratio of brine mobility to polymer solution mobility measured at residual oil saturation: RF= ?m/?p= (km/µm)/(kp/µp)M.......(1) where RF = resistance factor (dimensionless) k*. and A, = mobility of water and polymer solution, respectively k,,, and k,, = water and polymer permeability, respectively (darcies) µie and µp = viscosity of water and polymer, respectively (poise). Eq. 1 is similar to the expression commonly used to relate the relative mobility of the water bank at residual oil saturation to oil-bank mobility at irreducible water saturation: where M =mobility ratio of water to oil (dimension-less) A, = mobility of oil k, = permeability to oil (darcies) )i* = oil viscosity (poise). From Eqs. 1 and 2 it is apparent that the polymer-solution-to-oil-mobility ratio can be approximated by dividing the brine-to-oil ratio by the resistance factor RF: Mpn=M10/RF...........(3) where M,-, = mobility ratio of polymer solution to oil (dimensionless). This simplified presentation assumes no dilution of the polymer solution by connate water. Also, the presence of a connate water bank separating the polymer solution from the displaced oil is not considered. Displacement of oil by waterflooding is increasingly dominated by viscous forces as the viscosity of the oil displaced increases. When the oil mobility is less than that of the injected water, the oil-water interface is not a piston-like front.3,' Instead, instabilities occur at the flood front in the form of viscous fingers which tend to penetrate the less mobile oil bank. The magnitude of these protrusions, or the degree of channeling, increases

Jan 1, 1967

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1910

By John K. Hammes, Stanley D. Michaelson

Generally, the mining costs reported for the large open-pit operations in the United States and South America lie within the range of $0.20 to $0.30 per ton of material moved. (These operations have strip- ping ratios ranging from 1.5 to 4.0.) Productivities for the larger North American properties are in excess of 200 tons of material per man shift, while those for the South American operations are less than 200 tons per man shift. The most significant variations in cost are in the categories of haulage and general mine cost. Haulage costs vary, as expected, according to the mine elevation, pit profile, crusher location, and accessibility of a dump area, and general cost variations depend largely on the overhead cost items included in this category. Drilling and Blasting Practice The majority of open-pit copper mine production drilling is performed by rotary drills. Hole diameter varies from 6 in. to 12 in., with 9-in. holes being most common, and penetration rates vary from 35 ft to 60 ft per hour.

Jan 1, 1968

By R. E. Cech, T. D. Tiemann

It has been shown that hydrogen may be made to serve as a rapid and eflicient reducing agent for Cu, Ni, Co, and Fe sulfides if a scavenging agent for hydrogen sulfide is intimately mixed with the sulfide particles being reduced. Accelerated reduction kinetics are demonstrated for nickel sulfide. Copper, nickel, and cobalt sulfides, when treated at certain temperatures in a combined reducing agent-scavenging agent system, are converted to voluminous masses of fibrous metal product. Studies have been carried out to determine the conditions which lead, on the one hand, to irregular poly crystalline fibers and, on the other, to long single crystal filaments a few microns in diameter. A mechanism is proposed to account for the formation of single crystal filuments. The sulfide minerals of Cu, Ni, Co, and Fe are an important source of these metals yet there has been comparatively little scientific effort devoted towards understanding reduction mechanisms of these minerals. This may be, in part, due to the fact that the most convenient reducing agents for carrying out such studies, viz., hydrogen and carbon, do not react appreciably with sulfides. We have found that the reaction of hydrogen with metal sulfides can be markedly accelerated by placing a scavenging agent for hydrogen sulfide in close proximity to the metal sulfide. A brief series of experiments demonstrating relative reduction rates is reported in this paper to illustrate the effect. With the reduction process thus accelerated we have observed an unusual type of reduction behavior on some of the sulfides investigated. Under certain conditions the metallic product of the reduction reaction takes the form of filaments growing outward from the sulfide particles. The present paper deals largely with efforts to classify the various types of growth forms observed. This study has shown that filamentary growths from sulfides take a much greater variety of forms than has heretofore been reported by Ercker,1 Hardy,2 and Nabarro and Jackson3 in their reviews of metallic growths from copper and silver sulfides. THERMODYNAMIC CONSIDERATIONS The thermodynamics for hydrogen reduction of metal sulfides is quite unfavorable. For the sulfides considered here equilibrium constants typically range from 10-3 to 10-5. These low equilibrium constants impose severe kinetic limitations on reduction since hydrogen sulfide must be transported out of the system at concentrations of only a few hundred ppm. Unless extremely high gas flow rates are employed the atmosphere surrounding any sulfide particle will always be essentially in equilibrium with the sulfide. If, however, one places an efficient scavenging agent for hydrogen sulfide in close proximity to the metal sulfide particles the concentration of H2S near the metal sulfide will be held to a very low value. This would permit the reduction reaction to proceed with little or no inhibition from a buildup of reaction product gas. It is well known that calcium oxide is capable of removing hydrogen sulfide from a hydrogen gas stream of low dew point.4 If a sufficient quantity of calcium oxide is mixed with the metal sulfide particles the reaction: CaO+H2S=CaS+ H2O [l] will substitute moisture in place of hydrogen sulfide in the gas stream and this will not affect, in a direct manner, the reaction: MeS +H2=Me + H2S [2] A convenient method of considering the thermodynamics of the combined reducing agent-scavenging agent system is to consider the atmosphere when the partial pressure of hydrogen sulfide is the same over both the metal sulfide and the scavenging agent, i.e., pH2S (1) =pH2S (2). As a consequence: pH2O (1) pH2(2) =K1K2 The chemical driving force for reduction will depend inversely upon the moisture content of the gas and will be 0 when, in the system, pH2O = pH2.K1K2. Table I lists values of the equilibrium constants for reduction and H2S scavenging reactions for a number of sulfides at several temperatures. Data are taken from Rosenqvist4,5 and Kelly.6 The equilibrium constant products calculated from this data show that the limiting level of gaseous reaction product has been increased by a factor of 10' to l04 as a result of substituting a reducing agent-scavenging agent system for a simple reducing agent system. One possible side effect which must be considered is the possibility that the moisture evolved in the scavenging reaction might cause the atmosphere in the system to be sufficiently oxidizing to favor the formation of oxide rather than metal. This possibility was examined by comparing the equilibrium constant products listed in Table I with equilibrium constants for hydrogen reduction of the respective metal oxides. It was found that for copper, nickel, and cobalt the combined reduction-scavenging reactions could not develop a sufficiently high oxidizing potential in the

Jan 1, 1970

By R. A. Vandermeer, J. C. Ogle

The preferred crystallographic orientations (texture) developed in randomly oriented, poly crystalline niobium during rolling were studied by means of X-ray diflraction techniques. The evolution of texture at both the surface and center regions of the rolled strip was carefully examined as a function of increasing defamation throughout the range 43 to 99.5 pct reduction in thickness. Certain aspects of the center texture development in niobium are in agreement with the predictions of a theory by Dillamore and Roberts, but others cannot be explained by the theory in its present form. Above 87 pct reduction by rolling, a distinctly different texture appeared in the surface layers which was unlike the center texture. The present results are compared with previous results obtained from other bcc metals and alloys. RANDOMLY oriented, poly crystalline metal aggregates when plastically deformed to a sufficiently large extent develop preferred orientations or textures. In a recent review article, Dillamore and Roberts1 pointed out that the nature of the developed texture may be influenced by a large number of variables. These include both material variables such as crystal structure and composition and treatment variables such as stress system, amount of deformation, deformation temperature, strain rate, prior thermal-mechanical history, and so forth. From a practical point of view, the control of preferred orientation may often be important for the successful fabrication of metals into usable components. During the past few decades many experiments have been devoted to the study of deformation textures. This work, however, has been confined in large part to metals and alloys that have an fcc crystal lattice. By comparison, bcc metals and alloys have received much less attention, and consequently our understanding of preferred orientations in these materials is only shallow. This state of affairs worsens when it is realized that almost all of our present howledge about this class of materials derives from studies on irons and steels.' The bcc refractory metals, which are relative newcomers to the industrial world, have, on the other hand, been given at best only passing glances in the area of texture development. Our understanding of the evolution of preferred orientations in bcc metals can only remain fairly limited until systematic studies of metals and alloys other than the irons and steels have been carried out and the influence of the many variables has been determined. To that end a program was initiated to investigate in detail texture development in niobium. The present paper reports some of the results of this study. Textures were determined at both the center and surface of strips rolled variously to as much as 99.5 pct reduction in thickness at subzero temperatures. Emphasis in this paper is on texture description and on texture evolution during rolling to progressively heavier deformation. EXPERIMENTAL PROCEDURE The niobium was purchased from the Wah Chang Corp. as a 3-in.-diam electron-beam-melted billet. Chemical analysis indicated the impurities to be less than 300 ppm Ta, 40 ppm C, 10 ppm H, 170 ppm 0, and 110 ppm N. All other impurities were below the limits of detection by spectrochemical analysis. This large-grained billet was fabricated into specimen stock so that a fine-grained randomly oriented grain structure resulted. This was accomplished in three deformation steps alternated with recrystalli-zation anneals of 1 hr at 1200°C in a vacuum of low 10"6 Torr range after each deformation step. The first step was to alternately compress the billet 10 to 20 pct in each of three orthogonal directions. The second step was to compress in only two directions 90 deg apart to produce a 2-in.-sq bar. The final step was to roll this bar 50 pct to give a 1-in. by 2-in. cross section. After the final anneal, metallo-graphic examination showed the material to have an average grain size equivalent to ASTM No. 5 at 100 times (i.e., 0.065 in. diam). Specimens cut from the center and edges of this bar gave no indication of detectable preferred orientation when examined by X-ray diffraction. Samples 1.5 in. long, either 0.625 or 0.750 in. wide, and approximately 0.400 in. thick were machined from this fabricated ingot. The surfaces corresponding to the rolling planes were ground so as to be parallel. The samples were chemically polished in a solution of 60 pct nitric acid and 40 pct hydrofluoric acid (48 pct solution) prior to rolling to remove any cold work introduced in the machining operations. Rolling was accomplished with a 2-high hand-operated laboratory rolling mill that had 2.72-in.-diam rolls. Prior to operation, the rolls were polished with 600 grit paper, cleaned with acetone, and then soaked in a container of liquid nitrogen for several hours. The samples were also soaked in liquid nitrogen prior to rolling and were recooled between each pass. While some slight heating of the samples occurred during rolling, this procedure maintained the sample temperature well below 0°C at all times. The samples were rolled unidirectionally, and the rolling plane surfaces were not inverted during any phase of the operation. The draft per pass averaged between 0.010 to 0.012 in. After 96 or 97 pct reduction the draft was reduced to 0.001 to 0.002 in. per pass. Samples were rolled to various reductions in thickness between 43 and 99.5 pct.

Jan 1, 1969

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By G. A. Vissac

The only fine coal washer with proved automatic controls, the feldspar jig is capable of good efficiencies even at low separating gravities, handles a variety of products, and treats 150 tph and over. IN continental Europe the feldspar jig is used almost exclusively for cleaning the fine sizes of coal; it operates with an artificial bed, made up generally of pieces of feldspar or of any other hard and heavy rock with good cleavages. A primitive form of this machine requiring close supervision was used in this country years ago, but output was small. The modern machines are generally air-pulsated Baum-type jigs, with capacities up to 150 tph, and treat sizes from % in. to 0, usually previously dedusted or deslimed. These jigs are equipped with very accurate and sensitive automatic controls insuring satisfactory operation even at low separating gravity and with feeds irregular in quality and quantity. This paper will deal more particularly with coal cleaning separation, but the technical studies apply equally to all minerals. Theory of the Feldspar Jig To understand fully the operation of the feldspar jig and to appreciate its potential value, it is necessary to measure and analyze the motion of small particles of various specific gravities, falling in various media, under various conditions. As no practical formulas were available for that purpose, the writer has developed new theories and established new sets of formulas, which cannot be demonstrated here. They are applicable to all minerals and to many problems of coal or mineral concentration. These formulas do not pretend to absolute accuracy, but results, tested by comparison with experimentally recorded data, are sufficient for practical purposes, as they give definite indications of trends, relative values, and order of magnitude of the many factors involved. For pulsating motions no earlier formulas are available. In the case of continuous currents or motions, such formulas as Rittinger's, Allen's, or Stokes', over a hundred years old, apply only to special shapes and sizes of particles, involve factors and coefficients difficult to measure or appreciate, and deal only with free motions. They are of little use in solving practical problems. Units used with the formulas presented here are in the CGS system. Lateral friction and suction have been taken into account according- to methods currently used in aerodynamics, and only hindered motion is dealt with. As the feldspar jig is primarily intended to create a fluid bed condition, the mixture of fluids and solids obtained is homogeneous, and the apparent specific gravity of the separating medium is calculated accordingly. For instance, if 20 pct of the volume is coal and shale, with an average of 1.60 sp gr, in a liquid of 1.10 sp gr, the actual specific gravity of the separating fluid is 0.80 x 1.1 + 0.20 X 1.6 = 1.20. The fundamental equations are as follows: The general motion of a particle falling in a medium of specific gravity equal to u, hindered motion. is dv/dt = g/Ls [ L (s-u) - u/g v2 [1] g = 981 cm per sec, acceleration of gravity, and L = thickness of the particle of specific gravity (s) and velocity (v). The initial acceleration dv/dt = g (1-u/s ) [2] is a function of the specific gravity of the particle, only for a given medium, and independent of its dimensions—an ideal separating condition. The terminal velocity Vt = gxL- (s-u)/u, [3] for a given value of u, is a function of s and L. Two particles, L, s, and L2 s2, are said to be equivalent if they have the same terminal velocity, and accordingly L1/L2=s2-u/s1-u. [4] Two such particles cannot be separated by continuous currents, in any concentrating device. Because the initial accelerated motion, which provides for efficient separation, is followed by a constant velocity, which has a limiting effect, it is essen-

Jan 1, 1956