Search Documents

By H. Habenicht, J. J. Scott

An experimental method is described to compare strain data for rock and rock bolts when exposed to shock waves released by blastings. Static and dynamic strains were measured. Bolt gage response indicated a static decay of the bolt anchorage coupled with a reaction due to blasting vibrations. A distinct loss of bolt tension was indicated during vibrations and this was accompanied by a smaller but steady loss of tension due to static loading. The strain losses were found to relate to the shock source distance and the vibrational amplitude in the rock and bolts. Millions of roof bolts are used each year to stabilize mine openings and prevent their failure. Frequently, bolts become loose and lose their effectiveness as reinforcement to the mine structure. Many attempts have been made to determine the cause of loosening, including observation of the bolt tension or bolt torque through the use of torque wrenches, compression pads, and load cells. Pull tests have been used extensively to determine anchorage characteristics.102 These investigations have shown that even when bolts are loaded below the nominal anchorage capacity of the rock under 'static' conditions they exhibit a decay of load through adjustments and slippage at the bolt anchor. Since bolts are quite often found with the plate hanging loose from the rock surface, this condition suggests that some additional mechanism may have played a part in loosening the anchorage. Vibration from blasting or shock loading have been suggested as one cause in this type of anchorage deterioration. This paper gives the results of an investigation carried on at the University of Missouri at Rolla to determine the influence of shock waves on rock-bolt anchorage stability. ROCK BOLT ANCHORAGE UNDER DYNAMIC LOADING CONDITIONS In this report dynamic loading conditions are defined as conditions under which rock and bolts are exposed to vibrations occurring as a consequence of blasting, machine vibrations, earthquakes, rock bursts, etc. Whatever the location of the shock source, the waves created suffer extensive alterations along their travel paths, depending upon the vibrational properties and geometric parameters of the transmitting media. Together with reflection, refraction and diffraction at material boundaries, waves suffer changes in their nature to form tensile, compressive and shear waves. They become polarized, retracted, accelerated, dispersed, so that the waves incident at a point in the material can be the result of either one or a combination of this wide range of processes. A certain fraction of the wave energy will be lost due to friction, deformation, and material failure at the anchor-rock contact. Thus, the physical nature of wave propagation is such that it inhibits an exact analytical solution. For this reason this investigation should be considered qualitative rather than quantitative even though numerical data have been used as a base. CONCEPT OF THE INVESTIGATION Experiments were designed to find, from a series of rock bolts installed in natural mine rock, whether or not, and to what extent, bolt tensions would be influenced when bolts were exposed repeatedly to shock waves such as those produced by blasting. Electronic instrumentation available in the rock mechanics laboratory of the University of Missouri at Rolla was used to observe wave development in the rock and vibrational reactions in the bolts. EXPERIMENTAL PROCEDURE Fig. 1 illustrates schematically the experimental equipment. Electric resistance wire strain gages were used as sensors for the strain response of the rock and the bolts. Bolts were 5 ft long and 5/8 in. in diam, equipped with two-leaf type expansion shells for 1 3/8 in. boreholes. The bolt gages were mounted by use of Du Pont Household Cement, covered with an epoxy insulation and then enclosed in a copper foil for electronic shielding. For details of placement and the wiring diagram see Fig. 2 and 3. The output of both the rock gages and the bolt gages was fed into cathode ray oscilloscopes from which the vibrational traces could be photographed. A static strain indicator was also used to read the output of all gages.

Jan 1, 1968

In cooperation with the United States Bureau of Mines and the Idaho Bureau of Mines and Geology, the University of Idaho offers in the School of Mines a number of fellowships. These fellowships are open to college graduates who have had good training in mining, metallurgy, or chemistry, and who are qualified to undertake research work. The income of each fellowship is $720 a year for the 12 mo. beginning July 1, 1919. Fellows will register as students in the University of Idaho and become candidates for the degree of Master of Science in Mining or Metallurgy (unless this or an equivalent degree has been earned). Their class work-will he directed by the heads of the departments of instruction, but the greater portion of their time will be spent in research work under the direction of the Bureau of Mines staff resident at the University. The purpose f this work is to undertake the solution of definite problems confronting the mining and metallurgical industries of the State of Idaho. For 1919-20 the following subjects are being considered: 1. Flotation-with especial reference to differential separation of various minerals. 2. Availability of western wood oils for flotation purposes. 3. Treatment of the complex gold-silver ores of southern Idaho. 4. Ore-dressing problems. 5. Mining problems. Applications, with certified copy of collegiate record, statement of professional experience, and names and address of three references, should be addressed to The Dean. School of Mines. Moscow Idaho_

Jan 6, 1919

By Carl Zapffe

Because no rock outcrops exist in the Cuyuna district, it is necessary first to make a magnetic survey with a dip needle, or possibly with a sun-dial compass, and determine the area or belt of magnetic variations and the maximum lines of magnetic attraction. A dip-needle survey is quicker to make, is sufficiently accurate, and will suffice. Regardless of how poorly defined the magnetic attractions may be, it is important that they be determined. Even if drilling has developed ore on an adjoining property, the survey should not be omitted. Iron-bearing formation is indicated by the magnetic attractions, but whether or not ore exists must be determined by drilling. The maximum line of magnetic attraction offers the best place to begin drilling. If no magnetic attraction exists, nearby developments are the only guide; and if these also are lacking, drilling is governed by guess. Test-pitting is not employed in exploratory work because the surface is too deep. Tunneling cannot be used because the topography is not suitable. Exploration shafts are a waste of time and expense, because from every standpoint drilling with churn and diamond drills is the most applicable method for exploratory work. Light drilling equipment only is needed. Rarely have heavier drills been required, for seldom do holes exceed 400 ft. in depth, and about 100 ft. of this is in glacial drift which is easy to penetrate. The deepest hole is 1023 ft. Because of the steep inclination of the strata and the narrowness of the orebodies, many angle holes have been drilled, mostly at 60' to 70" from the horizontal and against the dip of the formation. Angle holes are most advisable. If after initial drilling the beds are of shallow dip, vertical holes or holes of any angle can be used. The total cost of drilling a property is much greater if only vertical holes are used because more holes must be drilled to obtain the requisite information than when angle holes are used. Many tests for variation in angularity of a finished hole have seldom shown more than 2'; therefore, such tests may with safety be abandoned. Because the orebodies are generally about 100 ft. wide and cross a 40-acre tract at a slight angle, and as the dips are usually about 70"

Jan 1, 1925

By George Smith

IN discussing present-day business and industrial troubles we easily drop into the habit of clinical diagnosis. Talk of this kind, with its emphasis on suspicious symptoms and abnormal tendencies, makes us all morbid. As an English essayist has put it, we may thus induce a melancholy, temper that simply in-vites the ministrations of social and political quacks. It is far better-because nearer the truth-for us to recognize that our condition is in no sense diseased, that our body politic, social and economic, is suffering merely from growing pains; that America is not de-cadent-indeed, that any lapses from staid normality are traceable to the, excesses of youth. Our chief .trouble, then, is only that our industrial state is still young; it may be that we have been growing too fast. The growth in the industrial development of our country from pioneer days to the present time has been marvelous. Too many of us, however, take all this as a matter of course-we credit this record of American progress to our American genius alone. Too often we overlook the fundamental relationship between resources and progress-that man is aided and even guided by Nature. The fact is, social advance, indus-trial progress, national prosperity all have their ma-terial basis in natural resources. In furnishing the needed mineral raw materials to the great manufac-turing industries of the United States there has been no halt, but rather a general acceleration. No other phase of American activity can show-equal advance. As the decades have passed, the winning of mineral wealth has progressed from the role of a stimulus for western exploration to that of the foundation for nation-wide business. In 1890 the Sherman law was passed; since then the population of the United States has about doubled. Since then, too, thevalue of the annual product of the mines of this country has increased better than eight-fold-from 650 millions to 51/ billions of dollars. Since then the four largest branches of the mineral industry, which supply the iron and copper, the bituminous coal and petroleum-the bone and sinew and the energy of all other American industries-have increased their annual output nearly ten-fold as to value and six-fold as to quantity. Such a growth in the volume of mineral output must be taken as a true measure of the ex-ceptional service rendered by the mines of the United States. Not only is this a much larger country than it was 38 years ago, but its growing mineral industry has met demands that have been out of all proportion to the growth of the population.

Jan 8, 1928

Jan 1, 1932

Jan 1, 1961

Discussion of the paper of P. B. LIEBERMANN, presented at the St. Louis meeting October, 1917, and printed in Bulletin No. 127, July, 1917, pp. 1051 to 1062. P. B. LIEBERMANN.-As mentioned in my paper, a special investigation was made on the effect of dirt on the track, for the -express purpose of educating mine operators to the advantage of keeping their tracks clean. As to the benefit of clean tracks to the saving in battery consumption, that can be easily determined if the rate of discharge is known under existing conditions, that is, on dirty tracks. The tests have shown that tracks covered with coal dust cause an increase in draw-bar pull of about 30 per cent. The battery discharge table will show the capacity corresponding to the new rate of discharge and will thereby disclose the possible saving in battery consumption. The difference between dirty tracks and clean tracks will be found large enough to have an appreciable effect on the size of the storage-battery locomotive, and for a locomotive of any given size it may mean

Jan 1, 1918

By E. O. Fromm, R. I. Jaffee, R. M. Evans

IN connection with a research on gallium alloys, a method for the thermal analysis of very low melting alloys was developed, which appeared to be worthy of more than passing interest. As used, the method was suitable for work in the temperature range, — 72° to 250°C. However, with suitable adjustment, the method could be adapted for use over broader temperature ranges. The Rosenhain temperature gradient furnace,' adapted for low-temperature use, was the basis for the method. The gradient was set up in a stainless steel tube. The specimens were lowered through it at a constant rate while time-temperature or inverse rate data were taken. It was essential to maintain careful control of the top and bottom temperatures of the gradient. Also essential was good heat transfer from the walls to the specimen. This was accomplished by a liquid heat-transfer medium.

Jan 1, 1953

By G. S. Hume

As predicted a year ago, owing to the discovery in 1936 of crude oil on the west flank of the south end of Tuner Valley in the eastern foothills of Alberta, 50 miles southwest of Calgary, and the drilling activity that resulted, the production of crude oil in Canada during 1937 showed a very substantial increase over the previous year. The production from other parts of Canada is relatively small and shows slight variations only from year to year. The production of crude oil in Canada and the production in Alberta, the main producing Province, is shown in Tables 1 and 2.

Jan 1, 1938

By L. A. Wright

Union Carbide Corp.'s Pine Creek mine in California is the largest known tungsten deposit in the West, and the producer of well over five million tons or ore to date. Located 21 miles northwest of Bishop on the eastern slope of the Sierra Nevadas, the mine is also a source of molybdenum and copper and it was the quest for the molybdenum which caused the mine management to undertake a pillar recovery program. GEOLOGY For a full discussion on the geology of the Bishop tungsten district and the Pine Creek mine, reference is made to Special Report 47, Calif. Div. of Mines. The deposit lies along a 3000 ft segment of the contact between quartz monzonite and the marble that flanks the west side of the north portion of the Pine Creek pendant. All the components of a typical contact metamorphic tungsten deposit are developed; these consist of tactite, light colored calc-silicate rock and quartzose rock.

Jan 5, 1964

By P. Levesque

IN the process of alloying two metals to obtain a single-phase alloy, the end product is nearly always a cored structure. The mechanism of solid-

Jan 1, 1955

By I. L. Box

IN planning retreatment of tailings, the material to be retreated should be thoroughly investigated, tak- ing into consideration the total tonnage, the blende content, the specific gravity of the different particles, and the grinding necessary to liberate the mineral. The tailing pile is surveyed by making a closed trav-erse around the outer edges, locating the stations at points from which a considerable portion of the pile is visible. From each of these points the pile is sur-veyed by stadia and a contour map made. The yardage is then calculated from the contour interval and the area inclosed by the contours obtained with a planim-eter. A party of three men can survey an average tailing pile in one and one-half, days. In calculating tonnage it is assumed that 22 cu. ft. of tailing in place equal one ton. Sampling is done by the use of an auger with casing to prevent the hole from caving. These holes may be bored 12 to 15 ft. deep by hand, but to penetrate the entire pile some kind of power is applied to drive the casing and raise or lower the auger. The latter method is more expensive but the increased cost is more than compensated for by the value of the information obtained.

Jan 7, 1928

By Walter Dake

THE mining engineer is being more generally called on to examine and report on properties where the introduction of mechanical loaders is proposed, and as the use of these labor-saving devices presents an entirely different problem from that of hand-loading, an outline of procedure is herewith pre¬sented based on five years of intensive field experience in making such studies. It is impossible to outline an examination which will cover every condition but the most important variables are noted and the re¬port may be amplified or abridged to suit individual mine requirements. There are, of course, exceptional cases in which a single minor variable will determine the final conclusion; the result of mechanical loader application can be, estimated within close limits by considering all variables listed and taking into account the sum of all those found to be applicable to the property under examination. It is necessary that a high degree of accuracy be exercised in the analysis of conditions, and that a relatively narrow margin be figured on all estimates of tonnage outputs and costs. In making an examination for this purpose the data as to company name, business address, name of mine, geographical location, rail or water connections, type of mine (whether shaft, slope, or drift), and the name of seam should, of course, be included, to be followed by the minimum, maximum, and average thickness of seam, a brief description of the charac¬teristics of the coal, the impurities contained, location of regular impurities or partings, together with nota¬tion as to quality, uses, and-markets for the coal. It is also necessary to make cross-sections of the seam so that face preparation may be studied in an effort to eliminate all regularly-occurring impurities at the working place. The possibilities for further cost re¬ductions by the removal and gobbling of partings under¬ground before mechanically ? loading out a face are sufficiently great to warrant careful study and analysis. The classification of the mine from the standpoint of gaseous or non-gaseous operation will determine the general type of electrical equipment needed. A notation regarding the power whether generated at the mine or purchased, together with the amount, voltage, and type of current available is necessary since these matters determine the exact type of elec¬trical equipment to be used. A brief description of the ventilating system, giving type of fan, amount. of air delivered, water gage, and whether force or ex¬haust type, will enable the engineer' to figure venti¬lating requirements per man under mechanical loading practices. The pitch of seam in degrees, the pitch of working faces, and a brief description of rolls or horsebacks should be included, as these affect the efficiency of mechanical loading and, therefore, the economic re¬sults obtainable. -Notations should be made as to the amount of water found in working faces, and whether pumping, sprinkling or rock-dusting methods should be considered. As the character of the floor affects the operation of the machine at the face if a cater¬pillar-tread type, its hardness should be determined, and also whether impurities consisting of floor ma¬terial are likely to be loaded with the coal. The char¬acter of the roof and overlying stratification determine the mining system and width of roof span at work¬ing faces. It therefore directly regulates the amount of tonnage to be loaded by machines without a move from one place to another.

Jan 12, 1927

Jan 1, 1949

Jan 1, 1949

Jan 1, 1892

By F.M. Walters

In order to isolate the effect of an element on some property of an alloy, the effect of the other alloying elements must be elimi-nated, either by reducing their quantity to the extent that they may be neglected or by determining the specitic effect of each. The success of Grossmannl in calculating hardenability from chemical composition by means of factors suggested such a

Jan 1, 1943

By F. M. Walters

In order to isolate the effect of an element on some property of an alloy, the effect of the other alloying elements must be elimi-nated, either by reducing their quantity to the extent that they may be neglected or by determining the specitic effect of each. The success of Grossmannl in calculating hardenability from chemical composition by means of factors suggested such a

Jan 1, 1943

By Samuel Taylor

IT is customary for the president of an engineering society, in his annual address, to describe either some engineering problem with which he has beer connected or to review the work of the society during his administration. My first thought, this being the sesquicentennial year of our nation, was to review the advance in coal mining for the past fifty years, during which period I have been more or less intimately con-nected with the bituminous coal industry, and have personally witnessed most of the great changes which have occurred in methods and machinery used in the production of coal, but preparation of the requisite address would take more time than could be spared to prepare it, and its presentation would consume so much time that it .would not be suitable. The new arrangement providing for giving the presi-dent's address at the business meeting makes it more .appropriate to review the work of the Institute during the past year, together with some suggestions which appeal to me as being of advantage to the future wel-fare of the Institute, which I will try to do briefly. The work of the business office has been reviewed in the Secretary's report and it will not be necessary for me to dwell on it. Suffice it to say, it seems to be going along very well. Additional work could be done which would be to the advantage of the Institute, if we had the money with which to defray the necessary ex-pense incident to it, but I will refer to this again later. I would be derelict if I did not refer to the splendid work of the Secretary and the Assistant Secretary. Keeping in touch with all the sections, which number now about 26, and affiliated student societies which number 40, besides special committees, and represent-ing the Institute on various boards, provides work enough to occupy the Secretary's time almost exclu-sively. In addition to this the Secretary and the As-sistant Secretary have the work of editing and publishing the TRANSACTIONS of the Institute; the issuing of the magazine, MINING AND METALLURGY, in the splendid manner in which it goes out to the mem-bership is no light task and I think they should receive the commendation of the membership for this work.

Jan 3, 1927

Percussion drilling with tungsten carbide insert button bits ranks among the most significant advances in both underground and surface drilling in medium and hard rock formations. Getting top performance and life from these upfront components is not particularly difficult if one pays attention to the basics in operation and maintenance. For some reason, a few of the essential operating and maintenance steps for getting the most from these tools seem to have gotten turned around; instead of operating at the near optimum levels, some miners, in following myths or misunderstandings about them, are shortchanging their optimal utilization. Let's examine the two most harmful ones.

Jan 8, 1978