Search Documents

By Eugene Guccione

Australia could eventually become a major world supplier of uranium oxide-but how quickly that happens depends on the outcome of a highly complex and emotional battle among different special interests.

Jan 1, 1977

By J. G. Paterson, J. A. Meech

Abstract-Activated carbon is a strong adsorbent for amyl xanthate, capable of removing from solution up to a quarter of its own weight in xanthate. In selective flotation systems where depression is unstable, separation efficiency increases with activated carbon additions. The improvements observed are brought about by two mechanisms. First, by removing stripped and residual collector ions from solution, competition between depressant and xanthate is reduced and depression is stabilized. In addition, the texture of the froth phase at high pine oil concentrations is modified by activated carbon such that better drainage between the air bubbles takes place, alleviating the mechanical entrapment of depressed mineral particles. In treating a bulk copper/lead concentrate produced from GECO ore, selectively between galena and chalcopyrite is increased when activated carbon is used. Although the rate of flotation of galena is marginally lowered by activated carbon, a small extension in the duration of flotation allows the lead recovery to increase by 19% at the same recovery of copper. An addition rate of 0.75 kg/ton (1.5 lb/st) of bulk concentrate is suggested as optimum from this testwork. However, the actual level wed in the mill is dependent upon the residual concentrations of collector and frother in the bulk concentrate Pulp.

Jan 11, 1978

By R. E. Crater

Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crystallographic directions, and in materials containing quartz because of the a-ß transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 3, 1959

By O. E. Kiessling

Viewed from the standpoint of an economist, the task which faces the petroleum producing industry is one of intelligent adjustment so that technology can perform the job of efficient exploitation, while at the same time the interests of producers and consumers remain adequately protected. The crux in the task of making this adjustment lies in the difficulty of arranging the instrumentalities of production to accord with the physical characteristics of oil. For example, oil is exploited under a competitive economic system based on private ownership and contract, with the hope that profits will attract capital and enterprise, and with competition supposedly acting as the regulative factor. Whether such a scheme of industrial organization works is partially dependent upon the ability of the producer to withold or produce his commodity as he sees fit, in accordance with market demand. But in the oil industry, the enterpriser does not have complete control over the expansion and contraction of production, for, because of the decisions of the courts that ownership in oil depends upon its possession, desire for immediate output becomes the controlling force in production. Consequently, the theoretical commands and restraints of free enterprise are not operative because there is no security of property, and the result is loss due to the following economic maladjustments: (1) Production not completely responsive to price control. (2) Production at excessive cost. (3) Loss of oil, a highly exhaustible natural resource. If economic maladjustments are to be eliminated, there should be a change in the organization of production so as to provide efficient exploitation of the oil and at the same time to insure individual property interests. The latter is necessary if economic considerations are to become primary factors in regulating production. To attain these ends, the entire pool should be developed as one big engineering project and some scheme

Jan 1, 1928

By Bruce A. Kennedy

If it had not been for the persistent cold wind, the sun blazing out of a cloudless blue sky would have made it one of those warm, idyllic early spring days which attract the socalled "snowbirds" to Northern Mexico for a vacation at this time of year. At a drill site perched on top of a rather exposed mountain we were installing a number of borehole extensometers in diamond drill holes. A Threading Problem For the uninitiated in geotechnical instrumentation, a borehole extensometer is a series of anchors installed at various depths in a borehole, each anchor being independently connected by a tensioned wire to a measuring device set in the collar of the hole. Any movement of the rock at depth is detected by the anchors and transmitted by the wires to the measuring device. Flexible plastic tubing is used as a spacer between the anchors and the measuring wires are run up the inside of the tube. At this particular site we were installing an instrument string nearly 1000 ft in length. Threading wire only 0.041 in. in diam through 1000 ft of plastic pipe is almost as difficult as getting the proverbial camel through the eye of a needle.

Jan 1, 1971

By A. L. Holley

(Read at the Amenia Meeting, October, 1877.) THE three principal mines from which the celebrated Salisbury iron ores are obtained are called respectively the "Old Hill," "Davis," and "Chatfield" ore beds, and are situated in the town of Salisbury, Litchfield County, Conn., on the eastern slope of the Tocconuc range of hills.* The Old Hill Ore Bed is a tract of land of 100 acres, originally granted by the General Court in October, 1731, to be laid out by Daniel Bissell of Windsor. It was soon after surveyed and located by Ezekiel Ashley and John Pell. The descendants of Ashley are still proprietors in the mine. The supply of ore has been very abundant, and for many years was easily obtained, but latterly the cost of raising has been greatly increased. Up to about 1840 the average yield was estimated to be about 4500 tons per annum. The production has gradually increased until the average yield at pres¬ent is estimated at 15,000 tons annually. The largest production in any one year was about 20,000 tons. The proprietors of this mine were incorporated many years ago under the style of "The Salisbury Ore Bed Proprietors." The Davis Ore Bed, named after an early owner, was originally called Hendricks Ore Bed, and was owned before the organization of the town of Salisbury by Thomas Lamb, one of the first settlers *The data from which the historical portion of these notes has been compiled were collected by the Barnum-Richardson Company, of Lime Rock (Salisbury), Conn.

Jan 1, 1878

By S. L. Crouch, C. Fairhurst

The general term "coal mine bump" refers to the sudden and violent failure of in-situ coal. Coal bumps occur in most countries where coal is worked by underground methods. They are related to geological factors and mining techniques. Coal bumps can be characterized as unstable releases of energy associated with yielding that occurs with progressive mining. Unstable releases of energy occur when the coal is able to absorb less energy than is released by the surrounding rock mass during the yielding process. At any stage of mining, the amount of excess energy so released is governed by the mining geometry, the overburden stress, the elastic properties of the rock mass, and the stress-strain characteristics of the seam material. If the coal in the vicinity of the working face is crushed, the peak abutment pressure occurs at some distance into the intact portions of the seam, and mining takes place in essentially destressed coal. With subsequent mining, additional yielding occurs, excess energy may be released, and the peak stress is again shifted into the solid. This process continues until the mining geometry is such that the zone of peak stress is effectively surrounded by yielding coal, at which point it can be anticipated that further mining will produce dramatic redistributions of stress and be accom¬panied by large releases of energy. On this basis, the differences between several alternatives for mining a given block of coal may be pronounced.

Jan 1, 1975

By J. P. Witherow

The Clapp and Griffiths steel-process may be considered a pneumatic system, similar to the Bessemer, with the difference that the converter is fixed or non-tilting, and that the blast is introduced around the lower section of the converter instead of through its bottom. Mr. Griffiths was engineer-in-chief of the Gilchrist & Thomas basic dephosphorizing process during all the time those gentlemen were experimenting and working up their system, as Mr. G. communicated to me. After separating from these gentlemen, he began developing the present Clapp and Griffiths type of converter. Dr. Clapp, of Nantyglow, Monmouthshire, was a prominent physician in a large iron district. Previous to his association with Mr. Griffiths, he took out some patents on a process of his own for the manufacture of steel, which patents stood in Mr. Griffiths' way; hence the consolidation. Early in the summer of 1883, my attention was called to the experiments of Messrs. Clapp & Griffiths in Great Britain by a friend who had just returned from England. Later in that summer I went to Newport, on the border of Wales, where I met Messrs. Clapp and Griffiths and their friends. After visiting two small converters of their type which were in operation at different works, and spending a few days in the iron-districts of Wales, I went to London, where I met my friend Henry W. Oliver, Jr., who had already heard of the new steel-process. We decided to revisit Wales and examine more fully the process, more especially that Mr. Oliver might have the opportunity of coming practically in contact with the men and die process himself, so that his judgment might not be influenced by my sanguine feelings. On

Jan 1, 1885

By William B. Plank

THE growing dependence of our vast industrial civilization (:n mineral products demands today, as never before, the highest technical skill in those who produce these product-;. That the duty of training the engineers, whose responsibility it is to produce these mineral products efficiently and in sufficient amount, falls directly on the schools of mining is beginning to be more fully recognized. The Institute, realizing this fact and that its future membership depends largely on the annual accretion of young men, is showing a keen interest in the problems of the mining schools and in the work of its Committee on Engineering Education. The Committee has, during the past several years, considered the problems connected with the training of men for the mineral industry, whether these have been problems of college training, or placement of the young engineer in the industry, or personnel training after he enters the industry. The field of interest and discussion has been as broad and varied as the mineral industry itself. Coal mining, metal mining and metallurgy have been discussed and the papers on these subjects have been outstanding contributions to the literature on mineral education.

Jan 1, 1931

By K. K. Kohli, S. S. Peng, R. E. Thill

Introduction Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months' survey, the data collected include: 17 longwall panels and 2 room and pillar sections. The data in each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages. Most subsidence surveys started with the first panel and ended with the second or sometimes, but rarely, the third panel. The first panel may be located in a virgin area but frequently it was adjacent to (on the tailentry side) a mined-out room and pillar section. It must be noted that all of the subsidence data is restricted only to the amount of vertical subsidence and that the horizontal displacement measurement was completely ignored. Primarily due to the fact that vertical subsidence is the most striking feature in a subsidence trough, which is mistakenly considered to be the only critical contributor to surface structural damages, and that a horizontal displacement survey is much more complicated and time-consuming.

Jan 1, 1981

By Arthur L. Crawford

PLAGER gold is perhaps the most difficult of the common mineral deposits to evaluate. Not only are the erratic pay streaks a source of never-ending uncertainty, but the spotty distribution of the gold in iso¬lated nuggets is a perpetual source of error and disappointment to the sampler. Experienced engineers have long realized this difficulty and have been wary in predicting assay values except in the most general terms, and then only after extensive and usually expensive sampling. During the past year I have had the opportunity of checking a number of gold placers, and from the results obtained I believe that the microscope may be employed to advantage in placer sampling.

Jan 1, 1933

By William Kent

ABOUT a year ago, the writer had occasion to assist Mr. John L. Gill, Jr., of the Pittsburgh. Car-wheel Works, in making a trial of his new testing machine. A piece of Bessemer steel, of about .34 carbon, was used as a test-piece, turned to a sectional area of one square inch for a length of five inches between shoulders, and pro¬vided with large round heads, which were fitted to what is called the " Wade grip." Measurements of elongation, accurate to , 1/10000 of an inch, were made by a special apparatus containing two micrometer screws, with electric contact attachment. The machine was operated by hand-power. Readings of elongation were taken at each increment of 2000 pounds stress per square inch, up to 44,000 pounds, the elongation corresponding to the latter figure being .0088 inch. The elongations up to this point remained almost exactly proportional to the stresses, the strain diagram, as shown on the Plate, from the origin to the point A, being a straight line (the deviation of no observation from the straight line being greater than .0002 inch). There being no indication of an approach to the elastic limit, the attendant at the hand-wheel and scale-beam was told to proceed as usual and move the poise forward 2000 pounds, or to 46,000, and turn the wheel until the beam was balanced. Noticing that the beam did not rise in the usual time, and that the elongation was increasing rapidly, the writer called to the attendant to stop turning the hand-wheel and to push the poise backwards until the scale-beam balanced. Instead of balancing at between 44,000 and 46,000 pounds, as was expected, it balanced at 40,000 pounds, and the elongation had increased to .0343 inch (or more than four times that recorded at 44,000 pounds), as plotted at the point B, the dotted line between A and B showing the supposed course of the strain diagram between these two points. Immediately upon recording the elongation the writer said to Mr. Gill, who was standing alongside: "This phenomena is without a parallel in my experience, and I know of but one way to account for it. The piece must actually be broken in its interior, through a flaw or weak portion of the metal. The test-piece is now equivalent to a tube, with

Jan 1, 1880

By Kevin M. O’Connor

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation in rock masses induced by mining. The first example involved monitoring the propogation of overburden fractures above a longwall coal panel and the second example involved the use of TDR to monitor rock mass deformation in the vicinity of a strip mine highwall. Rock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

HOW the Engineers' Memorial clock and carillon at Louvain has impressed the people of that city is indicated by the following letter sent by the Secretary of the University of Louvain to the Secretary of the United Engineering Society. We are still full of the memories of that splendid July 4, when we came into such .delightful contact with our American friends and more specially with the representation of the engineering societies of the United States. It was a great joy for all the members of the University to see those, American friends who have given to us such a splendid memorial in honor of- the brave men who fell in the Great War.

Jan 1, 1928

By David M. Hopstock, Jose M. Pastrana

The magnetic susceptibilities of samples of natural and artificial hematite and natural goethite were measured by the Faraday method as functions of temperature, magnetizing field strength and particle size. All samples showed weak ferromagnetism, which accounted for large variations in susceptibility with field strength and particle size. Three probable sources of the weak ferromagnetism were identified.

Jan 1, 1978

By Jay A. Carpenter

IN six years the construction of Hoover Dam and the power plants probably will have reached the operating stage and this vast new source of power will then be continuously available for industry. The height of the darn will be 580 ft. and the average annual flow of the Colorado River is calculated at approximately 24,000 cu.ft. per sec. If this full head and average flow can be maintained the year round, about one million horsepower will be generated. The U. S. Reclamation engineers, taking into consideration the probable range in flow and head, have set the figure for power contracts at 660,000 firm horsepower, which can be assured at all times of the year. During the months of heavy run-off of water from the Colorado River Basin the power plants should be able to generate the full 1,000,000 hp. capacity of the power plants, so there will be 340,000 excess or secondary horsepower. The cost of firm power at the switchboard will be close to 2.15 mills per kw.-hr., equal to $14.05 per hp.-yr., and the cost of the secondary or off-peak power will be close to 0.8 mills per kw.-hr., or $5.22 per hp.-yr. In no place in the country can such cheap power be obtained today. The electrochemical industry is in a state of flux because the power costs from its old sources have increased so much (to $30 per hp.-yr. at Niagara) that the industries have had to seek new sources, so they have gone to Canada and Norway and built new plants.

Jan 1, 1932

By William Kent

About a year ago, the writer had occasion to assist Mr. John L. Gill, Jr., of the Pittsburgh Car-wheel Works, in malting a trial of his new testing machine. A piece of Bessemer steel, of about .34 carbon, was used as a test-piece, turned to a sectional area of one square inch for a length of five inches between shoulders, and provided with large round heads, which were fitted to what is called the " Wade grip." Measurements of elongation, accurate to 1/10000 of an inch, were made by a special apparatus containing two micrometer screws, with electric contact attachment. The machine was operated by hand-power. Readings of elongation were taken at each increment of 2000 pounds stress per square inch, up to 44,000 pounds, the elongation corresponding to the latter figure being .0085 inch. The elongations up to this point remained almost exactly proportional to the stresses, the strain diagram, as shown on the Plate, from the origin to the point A, being a straight line (the deviation of no observation from the straight line being greater than .0002 inch). There being no indication of an approach to the elastic limit, the attendant at the hand-wheel and scale-beam wits told to proceed as usual and move the poise forward 2000 pounds, or to 46,000, and turn the wheel until the beam was balanced. Noticing that the beam did not rise in the usual time, and that the elongation was increasing rapidly, the writer called to the attendant to stop turning the hantl-wheel and to push the poise backwards until the scale-beam balanced. Instead of balancing at between 44,000 and 46,000 pounds, as was expected, it balanced at 40,000 pounds, and the elongation had increased to .0343 inch (or more than four times that recorded at 34,000 pounds), as plotted at the point B, the dotted line between A and B showing the supposed course of' the strain diagram between these two points. Immediately upon recording the elongation the writer said to Mr. Gill, who was standing alongside: "This phenomena is without a parallel in my experience, and I know of but one way to account for it. The piece. must actually be broken in its interior, through a flaw or weak portion of the metal. The test-piece is now equivalent to a tube, with

Jan 1, 1880

By B. J. Harlan

THE trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and 1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years.

Jan 1, 1934

It took the US coal industry 55 years to increase domestic coal production by about 11%-from 568 million tpy in 1920 to today's level of about 630 million tpy. With such a growth record, it would take a few hundred years to double coal production. FEA planners think that it can be doubled in 10 years. "With all the obstacles continuously imposed on coal, the industry's real problem is not growth but survival," says Ray Albrechtsen, board chairman of Mountain States Resources Corp., and "we should consider ourselves lucky if, by 1985, the coal industry won't have been legislated and regulated out of existence."

Jan 5, 1975

By Arthur Notman

DURING the past fifteen years there has been a great change in the methods of treating employ-ment and discharge throughout industry. Perhaps nowhere has this change come more abruptly than in the metal mining districts of the West. In 1909, when I went to work for the Phelps Dodge Corporation in Bisbee, their operations were roughly arranged accord-ing to shafts in seven divisions, each employing from 100 to 250 men underground, and the mechanical department employing some 250 men, mostly on the surface. The underground divisions were each in charge of a foreman who had under him a night foreman and from two to four shift bosses on' each of two shifts. These foremen reported to the underground superinten-dent and he in turn to the superintendent of the mine department. The mechanical department was in charge of the master mechanic who reported to the superintendent of the mine department. RUSTLING A JOB IN THE OLD DAYS It was customary for men seeking employment to "rustle" the division foreman at the shaft during the lunch hour or at the close of the day shift and the master mechanic at the shops. There was no real attempt at interviewing the applicants for underground work. They simply filed in and out of the foremen's office-50 to 150 strong-in ten or fifteen minutes. If the foreman needed men, and he generally did; to replace those that he and the shift bosses had removed during the morning, he picked out those he knew or strangers who took his' fancy. The former in many cases were chosen for negative reasons rather than positive. In selecting the latter, the foreman felt that if they failed to show ability promptly, he could replace them the next day, and often did so. Even if these foremen had been skilful and well trained in the art of selecting men, it would have been impossible under the pressure of other duties to exercise that skill and experience in so doing. The conditions in the mechani-cal department were little better. About all that can be said in favor of such a method was that with a sur-plus of labor it "got by." The labor shortage brought about by the war disclosed its fundamental weakness.

Jan 6, 1923