Search Documents

By S. C. Sun, D. R. Mitchell

Experiments show that ores such as tungsten and tin, which slime excessively, can be deslimed and upgraded by ultrasonics. The method proposed depends primarily upon the stratifying and peptizing action caused when high frequency sound waves are propagated upward through ore pulp in a cylinder tube. Stratifying and peptizing are somewhat hindered by the accumulating action, which embodies additional effects of reflection and refraction.

Jun 1, 1956

By Walter Weeks

LITTLE study has been made of the pressure changes and energy losses that take place when an air current is divided into splits which subse-quently unite. The discussion and the experiments that are described in this paper deal with the division of an air current into square splits of equal size, the area of each of the splits at the downstream junction being one-half the area of the main duct. APPARATUS AND SYMBOLS The duct system shown in Fig. 1 was built of Y4-in. redwood and made as smooth as possible.The section of the top over the splits and the zone of mixing was of plate glass to permit observation of the stream lines. FIG. 1-DUCT SYSTEM. Static pressures were measured by means of pinhole tubes and a precise inclined manometer. Measurements of rates of flow were .made by determining the drop in pressure through concentric square orifices in the splits. The air was supplied by a fan operated by a direct-current motor that received its current from a motor generator set. Delicate rheostats in the armature. of the motor. made possible the perfect control of the fan speed, which was indicated on an electrical tachometer. Vanes to straighten the. flow were placed at the head of the main duct.

Jan 1, 1933

By M. M. Fine

Normally the U. S. produces less than 10 pct of its annual manganese requirement. About 95 pct of domestic consumption is used by the steel industry.' The strategic and critical nature of manganese has been recognized by its inclusion in the national stockpile and by intensified research directed toward cataloging and evaluating domestic manganiferous deposits. The USBM has participated in these activities for many years with field and laboratory studies to assess the extent and potential utilization of domestic manganese ores. One area of particular interest is in the vinicity of Batesville, Ark., where deposits have been mined since 1849 for both manganese and ferruginous manganese ores. Production is centered in Independence County, but deposits are also found in Sharp, Izard, and Stone counties in north-central Arkansas. Miser has described the geology and manganese mineralization in some detail.'. * "he rocks of the area are sedimentary, consisting of sandstone, limestone, shale, and chert. The two formations of greatest importance,' Fernvale limestone and Cason shale, are host rocks of the primary manganese mineralization. Through 1955 the district produced some 230,000 long tons of manganese ore (35 pct Mn or more) and 236,000 tons of ferruginous manganese (10 to 35 pct Mn).5 Most of the ore has been mined from deposits of manganese oxides in residual clays resulting from weathering of the two formations noted above. Concentration methods have been primitive, consisting for the most part of washing. hand picking, and jigging. A significant accomplishment in the district in recent years was the USBM recognition and investigation of the huge manganese potential represented by unaltered Fernvale limestone. systematic reconnaissance of manganiferous limestone and other occurrences has been in progress since 1953 to delineate the extent and tonnage of manganiferous materials. Results of that survey have appeared in two recent publications,1-5 which ascribe to the district an inferred reserve of 166 million long dry tons at a grade of 5 to 6 pct Mn. Most of this was mancaniferous limestone with an estimated content of 5 pct Mn. Specifications: Beneficiation was carried out on a group of manganiferous limestones to develop a way to recover commercial-grade concentrate from this extensive resource. The following chemical specifications were established by the GSA for metallurgical manganese ore acceptable for delivery to the national stockpile: Size specifications were not considered, as it was assumed that the concentrates could be pelletized or sintered. Manganiferous Limestones: Of the 11 samples tested to date, six were taken by cutting vertical channels across beds of limestone outcrops. Diamond drilling through overlying barren chert into unex-posed limestone provided four samples, and the last was a churn drill sample. In general, the samples were dlrk, fossiliferous limestone containing small amounts of braunite, hausmannite, rhodochrosite, massive and micaceous iron and manganese silicates, quartz, barite, and glauconite. The braunite and other manganese oxides partly to completely replaced some of the calcite and fossil material. The calcite was generously stained with mangenese and iron oxides. Phosphorus was present in all samples as collophanite grains, calcium phosphate fossil replacements. or an unidentified manganese-bearing carbonate. The difficulty in separating this complex array of minerals was further complicated by a very intimate association. Although some manganese grains as large as Ik in. were noted, grinding to subsieve sizes would have been necessary to liberate the components. Figs. 1 and 2 are micrographs, at X100, of typical polished sections in which white areas are manganese. gray is gangue, and black areas are surface depressions. By comparison with the 100 mesh opening, it is seen that some of the grains are coarse enough to respond, perhaps to tabling or flotation, but many are obviously beyond the scope of ohysical processing. Partial chemical analyses of the eight samples that were ultimately amenable to concentration are presented in Table 1. BENEFlClATlON RESEARCH Tabling: To take advantage of the presence of sand-size grains, both jigging and tabling were considered at the outset. Jigging was largely ineffective, but tabling achieved a partial recovery from most samples. As an example, the surface material from Baxter Hill was crushed to —28 mesh, hydraulically classified, and the coarsest spigot fraction was tabled to yield a concentrate, middling. and tailing. The latter two were reground to pass 48 mesh, combined with the primary fines, re-classified, and retabled. The middling and tailing were again ground, this time to pass 150 mesh, and deslimed at 20µ in a 3-in. hydraulic cyclone. The cyclone underflow was returned to the table to reclaim a small amount of high-grade manganese. An interesting facet of the gravity concentration developed on certain samples in which braunite was the principal manganese constituent. Since braunite has a Mohs hardness of 6 to 6.5, while the host rock, limestone. is only 3, a differential size reduction took place during crushing, and the

Jan 1, 1960

By R. S. Shoemaker, R. M. Darrah

Expanded markets for copper in the past few years and a consequent search for new ore bodies have revitalized the widely known but seldom applied method of producing copper called heap leaching. Heap leaching is defined here as the process applied to oxide ores which have been mined solely for the purpose of leaching. In this case, all costs of mining the ore become a part (and a substantial one, as will be shown) of the cost of the copper produced, whereas in dump leaching the mining cost has already been accounted for as a stripping cost for the sulfide ore. Of course, with newly opened ore bodies, stripping costs may be divided through accounting procedures, between the copper produced by the mill and that obtained by leaching, but in general this type of operation must be economic on the basis of the sulfide ore alone. Heap Leaching Requires Low Capitalization Heap leaching, as a beneficiation method, is unique in that it is the only process used for the recovery of a metal in which the time involved from mining the ore to metal production is measured in months instead of hours or at the most, days. Then too, after the ore body has been depleted and mining has ceased, metal production will continue for some substantial period of time. Heap leaching is also unique because unlike any other method of beneficiation, metal recovery cannot be accurately forecast ahead of time and recovery will never approach that of a conventionally milled sulfide ore or even that of a vat leached oxide ore. Counter-balancing this drawback, however, is the relatively low capital expenditure necessary to put a heap leaching operation into production and the consequence that smaller ore bodies which would not support the higher capital cost involved in a vat leaching plant can be made into producers. Stated more simply, in heap leaching the operator accepts low recovery in exchange for low capital costs and low break even point. Whether the operator chooses vat leaching with its higher recovery and higher capital costs, is a mater of economics which depends in part on the nature of the ore to decide. For instance, an ore that will vat leach in 7 to 10 days using 7 pounds of sulfuric acid per pound of copper produced might use double or triple that amount of acid during the months that are required for heap leaching.

Jan 12, 1968

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

The steady-state operation of an isothermal, counter-current reactor in which a mouing bed of hematite particles is reduced by hydrogen has been modeled mathematically using a generalized single-particle kinetic formulation for topochemical reduction with formation of the intermediate oxides, wustite and magnetite. Reduction prof iles have been generated for various oper- REDUCTION of iron ore, as practiced industrially, approaches counter current, granular-bed operation. The total process is extremely complex. Quite under- ating conditions selected to demonstrate the influence of major variables such as gas and solid flow rates, bed length, and particle size. These profiles illustrate , among other things, that the reducing-gas requirement in a countercurrent bed hinges upon the iron-wüstite equilibrium or 'pinch-point" in much the same way as in a staged reactor. standably, nearly all research has been focused on reduction of single particles of oxide under controlled conditions. While this approach simplifies the problem by eliminating interparticle interactions, the remaining intraparticle transport and kinetic processes still constitute a most formidable challenge. Only within the last few years has knowledge of single-particle reactions been developed sufficiently to make modeling of counter current-bed reduction a realistic and useful study of process behavior. The authors have analyzed1"3 extensive laboratory

Jan 1, 1969

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases. AMONG the many factors involved in rotary kiln efficiency, advantageous use of refractories is of major importance. So far as kiln lining alone is concerned durability is most significant, as shutdowns for repairs are costly in fuel consumption and production losses. Aside from selection of refractories best suited to the widely varying conditions under which rotary kilns are operated, lining design and accessory constructions within the kiln are highly important. The refractory most economical for any combination of operating conditions can be selected from a wide range of alumina-silica and basic refractories, including insulating, castable, and plastic fire bricks. In several cases silica brick can be used to advantage. Alumina contents of alumina-silica refractories range from 35 to 90 pct in increments of 5 to 10 pct. In general, bricks of relatively low alumina content are best for abrasion resistance, an important property for the brick used in chain sections of cement kilns or in feed end sections of limestone kilns. High-duty fireclay bricks of approximately 40 pct alumina and 55 pct silica are used to line the intermediate zones. Super-duty fireclay brick at slightly higher cost is warranted in operation of kilns with high intermediate zone temperatures and severe spalling conditions. Alumina-silica refractories with an alumina content of 50 pct and higher, termed high-alumina brick, are available in commercial classes of 50, 60, 70, 80, 85, and 90 pct alumina content. These refractories are generally used as high temperature zone linings or placed adjacent to the basic brick-lined sections when the treatment they are required to withstand is excessively severe. Use of basic refractories is confined mainly to zones of maximum temperature and most severe chemical action. Basic refractories ordinarily employed for high temperature zone linings of many rotary kilns comprise the classes shown in Table I. Each class is peculiarly well suited to various particular combinations of working conditions. The approximate chemical analyses of these classes also illustrate differences in compositions with respect to the major components.

Jan 1, 1956

PRESIDENT SAMUEL A TAYLOR, District 3 PITTSBURGH, PA PAST PRESIDENTS WILLIAM KELLY, District 5 IRON MOUNTAIN, MICH J V W. REYNDERS, District 0 NEW YORK, N Y FIRST VICE-PRESIDENT E DEGOLYER, NEW YORK, N Y TREASURER CHARLES F RAND. . . NEW YORK, N Y

Jan 1, 1923

By Eben E. Olcott

The Mine.—For some years attention has been drawn to the copper deposits of the Appalachian range of mountains, and especially to those in that portion crossing the corners of Virginia, North Carolina, and Tennessee. Certain it is that in many places in this locality available deposits of copper await the miner, and one after another are being opened and worked. The parts of these three States alluded to are but sparsely settled, and communications are insufficient to meet the demand for transportation. Railroads are wanted, as the existing wagon roads are unfitted for heavy hauling; these circumstances increase very much the difficulties in the way of mining enterprises. Notwithstanding this, the success of some of the mines of this section is an established fact, and Ducktown has for some years held a high rank among the copper-producing localities of the United States. of all these deposits, however, none is more interesting or more deserving of attention than the one now under consideration. The works of the Ore Knob Copper Company have been energetically pushed forward, since the reopening of the mine, in the spring of 1873, by Mr. J. E. Clayt,on, the superintendent and one of the chief owners of the property, and if one thing more than another can insure success it is the combination in this gentleman of rare business capabilities with the deepest personal interest in the prosperity of the undertaking. The copper vein at Ore Knob* is a clearly defined fissure traversing the gneissic rocks of Pre-silurian age in a direction 61' east of north.

For the third year in a row total value of the Nation's mineral production broke all previous records. A new peak of $20.4 billion was reached in 1964. So says the U. S. Bureau of Mines. The Bureau's preliminary estimate for 1964 is $800 million higher than the value reported for 1963, and $1.6 billion greater than the 1962 figure. The unprecedented demand for minerals, has stimulated development of new mines and expansion of processing capacity in many parts of the country.

Jan 2, 1965

By W. R. Davis

This paper presents a sunimary of the results of a study of the Dornick Hills-Springer sand reservoir of the Velma Pool. Stephens County, Oklahoma. The data are of interest because this type of reservoir is unusual in the mid-continent area. The reservoir is characterized by very steep dips and a relatively thick producing section. Its up-dip productive limit is defined by truncation of the productive sands, and the down-dip limit is defined by deterioration of sand quality rather than by the presence of an oil-water contact. The crude oil is of 29" API gravity, is relatively viscous and was saturated with dissolved gas at the original reservoir pressure. Consideratiqn of the physical characteristics of the reservoir indicates that natural water encroachment will be negligible, and that the producing mechanism will be a dissolved gas drive augmented by gravity drainage. Performance to date tends to confirm this. INTRODUCTION It is the purpose of this paper to present some of the features of the Dor-nick Hills - Springer sand reservoir which are unusual in mid-continent operations. The study was undertaken in an attempt to define the producing mechanism or mechanisms that will control reservoir performance, as an aid in determining well completion and production practices. GEOLOGY The reservoir under consideration is a series of sand bodies of Pennsylva-nian age found in the Lower Dornick Hills and/or Springer formations. For the purpose of this paper, the sand series is referred to as the Dornick Hills-Springer sand. This sand series lies on the northeast flank of the Velma anticline, and dips very sharply to the northeast in TWP 1S-5W, the average dip being about 45º. However, as shown in Fig. 1. the trend of the pool swings eastward in TWP 1S-4W with a coincident de- crease in dip angle. In this portion of the pool the average dip is about 25". Faults in Sections 30-1S-4W and 32-1S-4W are shown in Fig. 1. These faults show only minor displacements for the horizon contoured in Fig. 1, but they do show a pronounced displacement of the immediately overlying beds. Similar faults are thought to exist in TWP 1S-5W; however, since the detailed geological studies necessary to properly define these faults were not available to the author, no attempt to show them in Fig. 1 has been made. The up-dip productive limit throughout the pool is determined by the truncation of the Lower Dornick Hills-Springer sand. The down-dip productive limit does not appear to be defined by edge water, but by a gradual reduction in permeability of the sands. No dry hole has produced a significant volume of water from this sand section. There was a small gas cap in TWP 1S-5W. Most of the wells in TWP 1S-SW encountered an oil sand 70 ft to 150 ft thick, a shale 20 ft to 80 ft thick, and another oil sand 50 ft to 130 ft thick. A few scattered wells in this area encountered other and bodies below these

Jan 1, 1951

By W. R. Davis

This paper presents a sunimary of the results of a study of the Dornick Hills-Springer sand reservoir of the Velma Pool. Stephens County, Oklahoma. The data are of interest because this type of reservoir is unusual in the mid-continent area. The reservoir is characterized by very steep dips and a relatively thick producing section. Its up-dip productive limit is defined by truncation of the productive sands, and the down-dip limit is defined by deterioration of sand quality rather than by the presence of an oil-water contact. The crude oil is of 29" API gravity, is relatively viscous and was saturated with dissolved gas at the original reservoir pressure. Consideratiqn of the physical characteristics of the reservoir indicates that natural water encroachment will be negligible, and that the producing mechanism will be a dissolved gas drive augmented by gravity drainage. Performance to date tends to confirm this. INTRODUCTION It is the purpose of this paper to present some of the features of the Dor-nick Hills - Springer sand reservoir which are unusual in mid-continent operations. The study was undertaken in an attempt to define the producing mechanism or mechanisms that will control reservoir performance, as an aid in determining well completion and production practices. GEOLOGY The reservoir under consideration is a series of sand bodies of Pennsylva-nian age found in the Lower Dornick Hills and/or Springer formations. For the purpose of this paper, the sand series is referred to as the Dornick Hills-Springer sand. This sand series lies on the northeast flank of the Velma anticline, and dips very sharply to the northeast in TWP 1S-5W, the average dip being about 45º. However, as shown in Fig. 1. the trend of the pool swings eastward in TWP 1S-4W with a coincident de- crease in dip angle. In this portion of the pool the average dip is about 25". Faults in Sections 30-1S-4W and 32-1S-4W are shown in Fig. 1. These faults show only minor displacements for the horizon contoured in Fig. 1, but they do show a pronounced displacement of the immediately overlying beds. Similar faults are thought to exist in TWP 1S-5W; however, since the detailed geological studies necessary to properly define these faults were not available to the author, no attempt to show them in Fig. 1 has been made. The up-dip productive limit throughout the pool is determined by the truncation of the Lower Dornick Hills-Springer sand. The down-dip productive limit does not appear to be defined by edge water, but by a gradual reduction in permeability of the sands. No dry hole has produced a significant volume of water from this sand section. There was a small gas cap in TWP 1S-5W. Most of the wells in TWP 1S-SW encountered an oil sand 70 ft to 150 ft thick, a shale 20 ft to 80 ft thick, and another oil sand 50 ft to 130 ft thick. A few scattered wells in this area encountered other and bodies below these

Jan 1, 1951

By George E. Aiken

Subzero temperatures of the Arctic pose some critical engineering problems for the developer and operator of open pit mines. Undoubtedly, the single most troublesome manifestation of this climate is permafrost. Underlying about 20% of the world's land area and 85% of the state of Alaska, permafrost has not only made its impact on building construction and mine excavation, but has created a legitimate threat to the delicate balance of nature existing within the Arctic environment. The recognition of permafrost areas by geomorphology and an understanding of its other complex developmental factors are the basis for two major concepts in building construction. The active method involves the eventual thawing of the complete permafrost section and is only useful in shallow areas. However, in some areas of coarse, well-drained material, vegetation may be stripped well ahead of construction and shallow permafrost allowed to method, leaves the perenially frozen ground undisturbed and is to be preferred. In selecting construction sites aerial photos may clearly reveal typical permafrost features.

Jan 5, 1972

By R. A. Generes, H. C. H. Darley

Laboratory tests showed that at elevated temperatures a reaction takes place between all metal hydroxides and clay muds, which results in a thickening or solidifying of the mud, the extent of which depends on the nature of the ingredients. Calcium hydroxide gave the strongest solidification whereas barium hydroxide only caused a mild thickening, indicating that the use of barium hydroxide muds instead of lime muds would be a good way of preventing high-temperature solidification. It was found possible to prepare barium mud in the laboratory with caustic soda and a thinner in the same manner as lime muds, and these barium muds had the same or better toleration of high solids content, resistance to salt contamination, and low gel strengths as the corresponding lime muds. Three field trials have been made with barium mud. The principal difficulty encountered was in determining the correct proportions of the tourly treatments required to maintain low gel strengths. A satisfactory systern was finally developed, and low gels were maintained throughout the third test. The wells on which the trials were made were not carried deep enough to test the resistance to solidification adequately, but oven tests at 350°F were made periodically and no tendency to solidification was noted except immediately after severe cernent contamination had introduced excessive amounts of calcium into the system. Although barium hydroxide costs considerably more than lime, the total mud costs were as low, and on the last well significantly lower, than the average cost of lime mud wells drilled in the vicinity. INTRODUCTION The advantages of repressing dispersion and hydra-tion of clay cuttings carried in the mud, particularly when drilling through thick clay formations, are well recognized. This repression is generally achieved by the use of lime, and lime muds have in consequence the desirable characteristics of high toleration of solids, low thixotropy, and good resistance to contamination. They have, however, the disadvantage of high-temperature solidification. This phenomenon has been described in detail by Gray et al, who have shown that it is the result of a chemical reaction between the hydroxides and the clay minerals. The work described in this paper was undertaken to find a substitute for lime which would not cause this solidification. LABORATORY EXPERlMENTS The principal positive requirement for a substitute for lime is that it should repress the hydration and dispersion of clay. It is well known that monovalent cations promote hydration while polyvalent cations repress it. Therefore, a few representative polyvalent salts and hydroxides were tested to determine whether they could be used as substitutes for lime. Their efficiency at repressing hydration and dispersion was measured by means of the clay-volume test. It has been shown elsewhere' that this test is a good measure of degree of dispersion of clay in suspension and that hydration accompanies and correlates with dispersion, so that measuring one measures the other. The test is made by centrifuging a 1:100 mixture of mud and 1-N NaCl and observing the volume of sediment—the greater the volume, the greater the dispersion. The tendency to caux solidification was measured by heating the muds in pressure vessels for 16 hours at 150°F and 370°F. An approximate quantitative

Jan 1, 1957

By Richard H. Sibson

Changes in seismic style along the San Andreas fault system appear to correlate with strike-parallel variations in regional heat flow. Large earthquake ruptures are associated with colder segments of the fault zone, while comparatively high levels of microearthquake activity and small to moderate shocks occur along the hotter segments, often in association with aseismic creep. Such behavior is consistent with geotherm and strain rate dependent profiles of shear resistance versus depth, constructed for quartz-bearing rocks. These profiles suggest that the transition from frictional to quasi-plastic behavior with depth should increase by a few kilometers passing from the hotter to the colder portions of the fault zone, giving rise to long-wavelength concentrations of distortional strain energy near the base of the seismogenic zone in the cold segments. Some support for this hypothesis comes from the observed deepening of microseismic activity passing northwest and southeast from the central Californian active region to the currently locked, ~400 Ian segments of the San Andreas fault that ruptured in 1906 and 1857.

Jan 1, 1982

By AIME AIME

NO other man now on the Institute's Board has a record of long service to his professional society comparable with that of Karl Eilers. He joined in 1888; he was a Councilor as far back as 1909, a Vice-President as early as 1912, and for the last ten years has been continuously a Director and Treasurer. It seems fitting, therefore, that he is the only member of the present Board that is also an Honorary Member of the Institute. Karl Emrich Eilers was born near Marietta, Ohio, Nov. 20,,1865, which makes him 71 years old. Columbia School of Mines gave him his E.M. in 1889, after which

Jan 1, 1937

Jan 1, 1965

By H. W. Clark

Electricity must be safeguarded everywhere that it is used. The conditions that exist underground make the use of safeguards more essential there than almost anywhere else. Electric Shock Electric shock is the greatest danger in connection with the use of electricity in mines, because conditions existing underground are so favorable to its occurrence. Men are often obliged to work in more or less uncertain light near bare wires that are carrying dangerous potentials. The fact that the men are standing on the earth practically connects them to one terminal of the electric generator. The moat dangerous piece of electrical equipment underground is the trolley wire. It is necessarily bare and extends for long distances throughout a mine, often less than a man's height from the track rail. Sometimes the making up of trips of cars must be done near low-hanging trolley wires. All 'bare wires offer the same danger that troIley wires do, although not to the same extent. Apparatus that has accidentally come in contact with the ungrounded side of an electric circuit is almost as dangerous as the trolley wire. A severe and even fatal shock may be obtained by coming in contact with the frame of a motor or a switch box that has become charged with electricity, or "alive," as it is usually termed. It is also possible to obtain . shocks from the frames of locomotives and cars if track sanding, poor bonding or a similar cause has put a high resistance to earth in the path of the current. Fires Caused by Electricity The danger from fires caused by electricity arises principally from defective installation and careless upkeep or from injuries to equipment resulting from falls of roof or similar causes. Fires may be started by unrelieved short cifiuits, or grounds, by the blowing of open fuses, and by the overheating of resistances. Incandescent lamps can produce heat enough to ignite combustible materials if the dissipation of the heat from

Jan 1, 1915

By Juptner von Jonstorff

A discussion of the paper by Messrs. Jüptner von Jonstorff, Blair, Dillner and Stead, read by title at the Lake Superior meeting, but presented first at the New York meeting of the Iron and Steel Institute (October, 1904), and here published under a mutual agreement between the two Institutes. Correspondence. MR. R. HAMILTON (Glengarnock) wrote to say that it was known for many years, that unless certain precautions were taken in dissolving the sample, there was a liability to obtain a solution from which the ammonium-molybdate solution would not precipitate the whole of the phosphorus. In 1877 Blair and Finkiner independently attributed this interference to the presence of carbonaceous matter in the solution, derived from the action of acids on the combined carbon of the metal, and they directed that the solution should be prepared in such a manner as to destroy these carbonaceous compounds. This was practically effected by evaporating the acid solution to dryness and roasting the residue. Adolf Tamm, in 1884, accentuated the same view. There are methods founded on the above-mentioned observations which leave nothing to be desired in point of accuracy, but the evaporation to dryness with subsequent roasting and re-solution consumes much time, besides the minor inconvenience caused by large amounts of acid fumes. In 1888 P. W. Shinier suggested that the incomplete precipitation of phosphorus was due to incomplete oxidation of -.the phosphorus, and proposed to render all the phosphorus precipitable by oxidizing the solution with potassium permanganate, etc. Experiments were made to test the accuracy of this view (details will be found in the Journal of the Society of Chemical Industry, vol. x., p. 904), and the results obtained seem to-prove that it is the correct one. It was first proved that carbonaceous matter in solution did not prevent the precipitation of properly oxidized phosphorus

Mar 1, 1905