Search Documents

By Paul D. Tomlingson

Editor's note: This is the first of two articles on maintenance. Part two, "Effective maintenance downsizing techniques," will appear in the October issue of MINING ENGINEERING. Most mine managers are aware that the cost of maintenance rarely goes down unless work is done less often and with fewer people. Fewer people translates into downsizing and seldom means making maintenance more efficient. Even so, mines that have struggled unsuccessfully to improve maintenance and are now pressed to reduce maintenance costs may opt for downsizing. On the other hand, mines with an immediate need to reduce costs may be forced to downsize because they cannot wait for needed improvements to take effect. This can be bad news for maintenance. In any case, the mine must downsize correctly to ensure effective maintenance is sustained.

Jan 1, 1994

By Turnbull A. G

Thermodynamic calculations based on the ideal system NiO - Fe203 - H2(g) - CO(g) - H2O(g) - CO2(g) show that it is not possible to selectively reduce nickel oxide in the presence of hematite because ferronickel is the zero-valent nickel-containing product. The calculations show that temperature, reducing atmosphere composition and oxide to reductant ratio have a marked effect on the nickel content of the ferronickel alloy and the amount of nickel reporting jn the alloy. The general trends based on the calculations correlltte well with experimental observations.

Jan 1, 1980

By J. Roodt

Paper written on project work carried out in partial fulfilment of B. Eng (Metallurgical Engineering) degree This work was done to characterize the leaching of a uranium containing pulp processed by a South African producer to identify parameters that could be adjusted to increase the extraction of uranium in the existing circuit. Batch leach tests were used to characterize the leach properties and especially the influence of the oxidant concentration on the leaching achieved. It was found that relatively high extraction could be obtained even at room temperature by using a high liquid-to-solids ratio and that increasing the oxidant concentration significantly improved the leaching of the uranium minerals.

Jan 1, 2003

By D N. B Skinner, R L. Brathwaite, M S. Rattenbury

The Institute of Geological and Nuclear Sciences Ltd has carried out a mineral resource assessment of the Coromandel region, one of the most mineral-rich regions of New Zealand. The assessment focussed on metallic minerals and clays, because these are the main commodities that have potential for increased production and export from the region (and from New Zealand).   Three steps were used in the assessment: 1) development of mineral deposit models, 2) comparison of the models with regional geology, structure, geochemistry and past mineral production to estimate the number of undiscovered mineral deposits, and 3) application of grade-tonnage models to determine the quantity and value of the known and undiscovered resources. In step 1, descriptive and grade-tonnage mineral deposit models were developed for 11 different types of mineral deposits: ò     Low-sulphidation andesite-hosted epithermal Au-Ag ò     Low-sulphidation rhyolite-hosted epithermal Au-Ag ò     High-sulphidation quartz-alunite epithermal Au ò     Porphyry Cu-Au-Mo ò     Andesite-hosted polymetallic veins adjacent to mineralised porphyry stocks ò     Zn-Pb-Ag skarn ò     Cu-Ag skarn ò     Hot spring Hg ò     Shoreline placer Ti ò     Rhyolite-hosted halloysite clay ò     Volcanic-related kaolinite clay   Step 2 was aided by a geographic information system (GIS) assembled from a number of digital spatial data sets including: a digital elevation model, an aeromagnetic map (from open file mining company data), a geological map (from the GNS QMAP project), location of areas of hydrothermal alteration, locations of mineral deposits (from the GERM database), stream sediment geochemical analyses (from the REGCHEM database), and a lineament map derived from satellite remote sensing data and the digital elevation model.   Based on May 2001 commodity prices, potential resources estimated for the 11 mineral deposit and grade-tonnage models total NZ$22 806 million for the metallic minerals, NZ$1000 million for halloysite clay deposits and NZ$57 million for kaolinite clay deposits.

Jan 1, 2001

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

Owing to the increased consumption of sulphuric acid; Australian manufacturers have, from time to time, been seeking for a satisfactory source of sulphur that would make them independent of foreign supplies.Some years ago a considerable amount of acid was obtained from the roasting of Spanish pyrites. This ore, in 1913 or thereabouts, cost 16s. per ton f.o.b. Huelva, and freight to the eastern seaboard of Australia was about 20s. per ton. As the ore contained 48% to 50% of available sulphur, it was costing roughly 9d. or 10d. per unit, and, in addition, the cinder, after roasting, was a product of considerable value to smelters, containing as it did a high percentage of iron suitable for fluxing, and appreciable values in silver and gold.

Jan 1, 1925

By D M. Marques, J F. C L Costa

The estimation of process plant head grade is not trivial and is a source of constant dispute within the mining industry. Grade estimates informed by the short term mine planning are frequently not reproduced by sampling the continuous flow of ore at the plant. Head grades are normally obtained by periodically sampling the continuous flow during a day or shift, and taking the average of the multiple increments collected. The standard error of this mean grade depends on the ore variability and the frequency (number) of aliquots extracted. The more increments are taken the higher is the precision on the calculated mean. Variographic experiments are normally used to map grade variability along a certain period of time and the extension variance is derived from this variogram. This experiment is time consuming, expensive and cumbersome. Mining industry personnel rarely apply this approach. Additionally, a temporal variogram can vary from day to day as different ores are mined along the life of the mine. This paper investigates a novel approach based on simulating the grades feeding the processing plant. In situ 3D grade models are built using geostatistical simulations. Grade spatial continuity and variability are reproduced in models that mimic the real deposit. These models are used in mine planning and scheduling transforming a 3D block model into an one dimensional string of values feeding the plant (one dimension flow). These grades have the statistical characteristics of the unknown real grades and can be sampled to emulate a variographic experiment. The results showed consistency and adequacy to estimate the sampling error (Gy, 1998 p 31) for various sampling intervals using the simulated grades. Also the results show a variographic experiment can change significantly from time to time, as ore changes and a selected sampling protocol can become obsolete if not adjusted for ore variability.CITATION:Costa, J F C L and Marques, D M, 2012. Defining a sampling strategy for a continuous flow supported by geostatistical simulations, in Proceedings Sampling 2012 , pp 3-8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By E A. Amaral Jr, A C. Chieregati, J C. O Souza

Cross-belt samplers are designed to sample particulate material in processing plants, usually when there is no space to install a conventional linear falling stream sampler. Most of the available cross-belt samplers are mounted on the top of conveyor belts, and remove each increment from a loaded moving conveyor with a 360° rotation of an open faced cutter, in a plane perpendicular to the material flow. Despite the practicality of this equipment and the fact that it occupies very little space in the plant, cross-belt samplers are well known for collecting biased samples, especially due to the increment extraction error. Sampling consultants around the world tend to condemn this sampling equipment, claiming that it is incapable of collecting the fine material from the bottom part of the load, and, since the sampling probability is not uniform for all fragments and depends on its position in the stream, this kind of sampler generates biased samples and its use should be avoided. Furthermore, the greater the segregation effect between particles, the larger the bias. However, some plants, whose initial design did not plan for the installation of a falling stream sampler, must rely on cross-belt samples for process control and reconciliation. For the past years, sampling equipment manufacturers have been putting effort in modifying the cross-belt sampler design in order to comply with the principles of correct sampling. Changes to the cutter material, shape, position, speed and movement in relation to the material flow have been made, and are continually being tested for different types of ore with various chemical and physical characteristics. This paper presents the improvements made to a cross-belt sampler at a gold plant feed in Brazil and describes the tests performed until it was possible to validate the new sampling equipment for reconciliation purposes.CITATION:Chieregati, A C, Amaral Jr, E A and Souza, J C O, 2017. Validation of a modified cross-belt sampler for reconciliation purposes, in Proceedings Eighth World Conference on Sampling and Blending , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.' Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.' Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

By R. S. McClain

The Federal Bureau of Mines investigated residues from aluminum plants, to determine if carbon could be removed by flotation while recovering fluorine and aluminum compounds for recycling to the reduction process. This publication summarizes studies on samples representing three types of plant waste products, supplied by three aluminum-producing companies. Samples of flue dust, pot skimmings, and pot linings from the various plants all responded to a simple turpentine flotation scheme to reject 90 to 97 percent of the carbon. Aluminum compound recoveries ranged from 42 to 94 percent on the flue dust, were about 95 percent on the pot skimmings, and ranged from 75 to 89 percent on the pot linings. Fluorine recoveries from the same samples ranged from 35 to 63, 92 to 95, and 77 to 86 percent, respectively. The pot linings contained soluble salts of aluminum and fluorine which were recovered by precipitation with sodium aluminate and carbon dioxide gas. Composites of residues from each plant responded to flotation much the same as the individual samples. Aluminum is produced by the electrolysis of alumina in a molten cryolite bath. The electrolytic reduction cell consists of a carbon-lined box containing a pad of molten aluminum which serves as a cathode, a carbon anode, and an electrolyte of molten cryolite in which the alumina is dissolved. Alumina is reduced to aluminum at the cathode, and carbon is oxidized at the anode.

Jan 1, 1961

By D. Nyungu

Despite observations of spalling and damage of mine excavation wall rock in the Bushveld Complex (BC) over the passage of time, there have been very few time-dependent or creep tests carried out in South Africa on rock, particularly on BC rock types. The research described in this paper deals with the investigation of stress and strain conditions influencing spalling of wall rock in BC mine excavations, and the influence of time on the tensile strength of several BC rock types. Time-dependent laboratory testing of BC rocks was carried out in indirect tension. The results show that the magnitude of the tensile strength of BC rock types is approximately 5% of their uniaxial compressive strength magnitudes. The average long-term uniaxial compressive strength of the BC rocks, interpreted from the axial stress-volumetric strain graphs, is 56% of the UCS value. The long-term tensile strength is shown to be less than 70% of the normal tensile strength. Extension strains at tensile strength failure ranged between 0.16 and 0.21 millistrain. Values corresponding with the long-term tensile strength are less than 70% of this range, namely, 0.11 to 0.15 millistrain. These results represent new knowledge, since such rock testing and analysis does not appear to have been carried out previously on BC rock types. Elastic numerical modelling was carried out to illustrate the extents of tensile stress zones and extension zones around of typical BC mine excavations. The models showed that large zones of extension strain can occur around BC excavations, and that the magnitudes of the extension strain can substantially exceed the critical values determined from the laboratory testing. The implication of this is that there are substantial zones surrounding BC mine excavations that will be prone to time-dependent spalling conditions and perhaps more significant failure.

Jan 1, 2014

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent, high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptablecomputational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Richard F. Hewlett

The purpose of this Bureau of Mines paper is to provide the mineral industry with current information on high-speed data processing and to illustrate how some of these techniques can be applied to the industry. The need for applying these techniques is generally recognized, but not much information is readily available on specific applications. This paper briefly describes high-speed data processing and reduction equipment in an effort to familiarize the reader with the functions of the equipment. A list and explanation of some of the possible applications of high-speed data processing for the mineral industry are included. A few of these applications are illustrated by the use of specific examples of existing computer programs or processing methods, including their calculation times and costs. Some of the programs cited herein were developed by the author at the University of Arizona for a Masters thesis in mining engineering. When a reference is made to a specific computer, the reference is given to make the information that is being presented as factual as possible; most of the manufacturer's equipment that is mentioned in the references was available at the University of Arizona, and no specific endorsement of that manufacturer is intended.

Jan 1, 1962

A vital ingredient in ensuring that metals exploration companies, working in the developing countries of thePacific Rim, support the development of national geologists is making such a learning program cost-effective. There is a wide spectrum of learning needed in the development of these explorationists: the technical and conceptual skills to carry out exploration efficiently, the professional and managerial skills to apply the exploration in the work situation, the personal attributes required to manage their exploration effectively, and a company organisation that allows them to learn and use these skills and attributes.

Jan 1, 1995

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Deqing Zhu

"An innovative process of reverse floatation-direct reduction-low intensity magnetic separation was developed to effectively beneficiate the superfine run-of-mine (ROM) ore mined from Hunan Province, China. Mineralogy was measured that the ROM ore is of superfine low grade hematite ore type, assaying 27.2wt%Fetotal and with main valuable minerals of hematite occurring at size between 3 to 5µm. The upgrading results show that the final iron concentrate, assaying 88.3wt%Fe total and 94.5% metallization degree was obtained at an overall iron recovery of 69.9% under the following conditions: rough concentration by grinding of ROM up to 88.7% passing 0.074 mm and reverse flotation at pH=9.4, 100 g/t starch and 200 g/t dodecylamine (DDA), and coal reducing the rough concentrate pellets containing 12% calcium containing complex additive at 1200 oC for 120 min, and finally magnetic separation of the reduced pellets by grinding up to 89.2% passing 0.043 mm at 0.08 T field intensity.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 628 million ton in 2009 [1]. Iron making industries increasingly demand for high grade raw materials to improve product quality and reduce operation cost. However, availability of high grade natural ores is limited and enrichment of lower grade ores is necessary to meet the demand. Therefore, large quantities of superfine low grade iron resources are necessary to utilize in China at the moment."

Jan 1, 2011

By N. Hmidi, T. Yalcin, M. Papadakis, B. Hilscher

Mill tailings, containing iron sulphides in particular, pose an environmental concern since they constitute a potential source of acid mine drainage which can damage vegetation, harm soil and living organisms, and contaminate groundwaters. Proper disposal of acid generating tailings is therefore an important issue that must be addressed and resolved in a satisfactory manner. Placer Dome Canada operates a 4000 t/d gold cyanidation facility at Musselwhite mine, in northwestern Ontario, where the mill tailings have been classified as acid generating. This study was conducted to explore the effectiveness of froth flotation in removing the sulphide minerals from these tailings and producing a low-sulphur, non-acid generating material that could serve as a capping material for previously deposited tailings. Laboratory semi-batch flotation tests were carried out in accordance with an experimental design procedure, and a computer simulation program was developed to facilitate the evaluation of flotation performance. In this investigation, pH, collector concentration, and airflow rate were considered as the relevant flotation variables, and their effects were examined both experimentally and by simulation. Results have demonstrated that flotation can successfully desulphurize the Musselwhite mine tailings and render them non-acid generating.

Jan 1, 2004

By P Duplancic and C R Lilley, R Hudson, D Beck

For deep block and panel caving mines, undercut or extraction level instability can have as much impact on overall recovery as underbreak or the premature ingress of waste. If the area of the mine affected by excessive convergence is small, recovery is usually possible. However, there are several examples of entire blocks that were abandoned prematurely due to footprint collapse. Clearly, such global instability has a major impact on recovery and must be avoided – this is one of the essential tasks for the design team.The design problem is complex. The planning engineer must ensure that the footprint has sufficient capacity to withstand the maturing loads in the cave, accounting for the effects of stress path, geological structures and the rock mass conditions. These are often uncertain and only sometimes quantified.The demand on the footprint will also be influenced by decisions and actions taken during production, especially related to draw, which can worsen a developing problem. Perhaps most importantly, the design decisions that favour stability and lead to lower deformation also negatively impact on idealised cave flow. Many engineers aim to minimise the size of extraction level pillars, to improve theoretical future resource recovery but in fact this can reduce recovery if widespread deformation ensues due to the undersized pillars.In 2014, PT Freeport Indonesia undertook detailed numerical analysis to quantify the effects of variability in rock mass conditions and geological structure on overall footprint performance. The analysis accounted for a range of stress paths and maturing cave loading scenarios sourced from a calibrated whole-of-cave deformation-flow model. The intent was to replicate some of the diversity and distribution of pillar deformation outcomes that may be seen in practice at Freeport.The discontinuum finite element analysis was able to replicate damage localisation around persistent structures, a realistic distribution of drive deformation and show how small areas of instability can evolve into major problems if poorly managed. The limits of pillar size and ground support as solutions to a number of different instability problems was also investigated, showing that pillar size alone was not a sufficient remedy for all adverse circumstances.In this paper, we describe the workflow for numerical analysis of footprint deformation. We discuss the compromises and considerations for balancing the sometimes competing needs for efficient extraction levels pillars, ground support and prudent draw strategy.CITATION:Beck, D, Hudson, R, Wilson, A D, Duplancic, P and Lilley, C R, 2016. An investigation of factors affecting the long-term reliability of extraction level pillars in deep block and panel caves, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E Rojas, C Pardo

The exploitation of primary ores using cave mining caused new challenges at the El Teniente mine that required changes to a number of conventional cave mining practices. For example, in the 1970s and 1980s, panel caving was introduced to manage certain geotechnical and operational conditions. Today, El Teniente mine is facing new challenges associated with deep cave mining and establishing its New Mine Level (NML) project, which is located 240 m below the Esmeralda operating cave.The engineering and development phases for this new project have been largely based on experience and lessons learned throughout the history of primary ore exploitation at El Teniente mine, particularly knowledge about seismicity control, the management of collapses and operational practices. For example, previous experience demonstrated that seismicity could be managed by preconditioning using large-scale hydraulic fracturing (HF). HF has been systematically applied in the column of ore above the undercut planned for the NML project and below the production or extraction level, where the main ventilation and haulage infrastructure are to be located.This paper discusses how this has been achieved and is based on previous experience of preconditioning using HF, which has been applied in the selection and management of exploitation techniques and associated planning strategies and design parameters for the NML project.CITATION:Pardo, C and Rojas, E, 2016. Selection of exploitation method based on the experience of hydraulic fracture techniques at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M E. Taulis, S Hayton, D A. Manhire, J G. Pope

Successful development of coal seam gas (CSG) resources in low-rank coalfields such as the Powder River Basin has raised interest in CSG from low rank coal in New Zealand. Kenham Holdings Limited holds 12 Petroleum Exploration Permits (PEP) covering some of New ZealandÆs low-rank coal and lignite resources and has engaged CRL Energy Limited to assist in the systematic evaluation of the CSG potential of the permits. To date, exploration results from seven New Zealand coalfields reflect differences in coal type, rank, depositional environment and depth of burial between coalfields. Several of the explored coalfields are considered prospective for CSG. One of the most advanced Kenham exploration programmes is in the Hawkdun Coalfield, Central Otago.   The Hawkdun Coalfield contains a single, thick lignite seam with properties that are similar to the Powder River Basin. Preliminary results indicate the Hawkdun Coalfield is prospective for CSG with the potential to contain between 25 and 60 PJ of gas; enough to supply a 30MW power station for ten to 25 years. Further drilling is planned to investigate the economic viability of the Hawkdun Coalfield. The in situ permeability of the lignite, the amount and availability of free gas, gas saturation at depth and market opportunities will determine its economic viability. If initial pumping and production results in the planned exploration programme are promising, the Hawkdun Coalfield will be further developed with additional production drillholes to form a trial production pod.

Jan 1, 2004

By J. Morkel

During research on mainly the weathering of kimberlite, it became evident that its mineralogical composition is an important factor in the complex process of physical and chemical disintegration. The mineralogy of tuffisitic kimberlite breccias from two localities, the Cullinan and Venetia mines, is compared with special reference to the occurrence of associated clay minerals. The clay mineral composition influences the engineering properties of these rock types. It is illustrated how the presence of swelling clay components can be confirmed by ethylene glycol treatment and chlorite minerals by heat treatment using X-ray diffraction. Smectites are present in both tuffisitic kimberlites, dominant at Venetia while chlorite is more frequent at Cullinan. More tuffisitic kimberlite breccias samples from venetia were also characterized. It was found that kimberlite disintegration is correlated with the presence and abundance of smectite.

Jan 1, 2006