Search Documents

By H. L. Gilbert

Improvements in production of high-purity chromium metal by magnesium reduction of anhydrous chlorides and by hydrogen treatment of electrolytic chromium are reported. Hydrogen-treated chromium has been arc-melted, and the arc-melted material has been successfully forged, rolled, and swaged. The material also has been forged at liquid-air temperatures. X-ray and metallographic studies indicate the recrystallization temperature of rolled chromium sheet to be about 750° C. Preliminary investigation of hot-bending characteristics of rolled chromium sheet shows the minimum bending temperature to be about 325° C. The heat resistance of chromium has been investigated.

Jan 1, 1952

By R. C. Bunge

The success of a mineral separation is commonly assessed from the separation curve, a graph of the recoveries achieved versus the corresponding separator settings. Two values characterize the curve, first the "splitpoint" which is the separator setting that produces a recovery of 50%, and second a measure for the separation sharpness. The splitpoint represents the "mean" while the measure for the separation sharpness represents the "scatter". In modelling the performance of crossflow separations the mean particle behavior is calculated from the force equilibrium that determines the particle trajectory which leads to a deterministic model. The scatter is then represented by a stochastic model. This presentation discusses the modeling of a crossflow separation and some implications with separation theory. The model is shown to successfully predict the performance of a magnetogravimetric separator.

Jan 1, 1992

By I. Gombköto, G. Mucsi, S. Nagy, F. Kristály, Á. Rácz, R. Szabó, B. Egyed

"Present paper deals with the investigation of a Hungarian pumice. Grinding experiments were carried out in a stirred media mill for various residence time. Ground samples were tested with laser particle size analyzer to determine and calculate the material fineness (particle size distribution and specific surface area). The lime adsorption capacity was measured to monitor the reactivity. Alkali activated cement paste was prepared using ground pumice with various alkali activators. Cube shaped specimens were produced from the paste and the uniaxial compressive strength was measured at the age of 7 days. The resulted alkali activated material structure was investigated by XRD and FTIR. The results of the experiments show that pumice fineness has strong impact on its hydraulic activity, hence on the compressive strength and the structure of the resulted binder. Relationships between grinding fineness, material structure and strength of the raw and mechanical activated material as well as the alkali activated cement were revealed. INTRODUCTION Pumice is a natural pozzolan which can be used as raw material for cementitious materials in limited portion owing to its low reactivity. Furthermore, due to its mineralogical composition it can be used for developing a new environmental friendly binder, namely alkali activated cements (AAC) which are inorganic alumina-silicate materials with good cementitious properties (Almalkawi et al., 2017; Özodabas and Yilmaz, 2013; Najimi et al. 2018; Yadollahi et al., 2015). Despite being a rather recent research topic, many papers and books have been published focusing on various aspects of alkali activation. There is great variety of raw materials that can be utilized for AAC production. However, primary raw materials are very expensive and secondary materials are heterogenous in composition. Therefore, a more homogeneous and low price silicate would help to balance the properties and cost of resulting cement and easing the way for commercialization of AAC. However, the control of its reactivity is of great importance which can be realized using mechanical activation by grinding (Juhász and Opoczky, 1990; Djobo et al., 2016; Mádai et al., 2015). The goal of present paper is to investigate the effect of mechanical activation of pumice on the properties of the resulted alkali activated cement."

Jan 1, 2018

By L. Gutierrez, M. Pawlik

The rheology artificial mixtures of bitumen with fine quartz of varying bitumen content, as well as actual oil sand ores, was investigated under different physicochemical conditions (pH, temperature). All rheological measurements were conducted using a Haake Rotovisco VT550 rotational viscometer, connected to a fixture specifically designed to measure properties of settling suspensions. It was found that at low bitumen contents (1 %, wt.) the pH of the slurries was the most important parameter that controlled the rheology of quartz-bitumen slurries. At higher bitumen contents (10%, wt.), it was a combination of high temperature and high pH that gave the lowest apparent viscosities and yield stresses of the model mixtures. These model observations correlated well with the rheology data obtained for slurries of actual oil sand ores. The overall results were discussed in terms of aggregation-dispersion phenomena between bitumen and mineral particles.

Jan 1, 2009

By T. S. Govindan

The first step in energy conservation in any industrial plant involves implementing many of the day-to-day "house-keeping" items such as fixing leaks, turning out lights, etc. When this step has been accomplished, additional opportunities require a detailed analysis of the energy systems, evaluation of risks and costs, and assignment of priorities. Examples of conservation schemes drawn from the experience of Du pont's Energy Management Consulting Services will be discussed. The utility of heat balances for kilns and dryers in minerals processing will be outlined. The inputs needed from Management for the success of conservation efforts will be discussed.

Jan 1, 1978

By C. R. Montgomery

Coal companies in order to supply their customers En the metallurgical market, both home and abroad, must be able to control their production in order to meet carbonization specifications over and above those of the proximate analyses which has been the prime consideration of purchases in the past. It is the purpose of this paper to review in brief some of the tests used and give data to show the application of such as it applies to the customers needs. It is now recognized that coal is not homogeneous in any of its properties and an amazing fact is that it has been used for so long a time as the principal raw material for the manufacturing of coke without more emphasis having been placed on the variation between coals; yes, even from coals in the same seam at different geographical locations, Recently Kuchta and Clendenin pointed this fact out In a study of the(1) carbonizing behavior as related to chemical and plastic properties of Alabama medium volatile coal.

Jan 1, 1962

By J. Kallioinen

Theoretical considerations, experimental results and plant experience have lead to a new design concept called the unit reactor approach. It has been successfully implemented to the largest flotation cell on the market, the 4000 cu ft OK TankCell. The work has also lead to a new operating idea called size specific flotation. The paper discusses these concepts in the view of full scale field experiments. In large scale porphyry copper flotation experiments conducted in Chile the new large TankCell with its new low energy input Free Flow mechanism out-performed the more conventional designs. The recovery was substantially better, especially in the coarse fractions. In some experiments the difference in total recovery was up to 10%-units and the savings in total energy consumption at the same time over 40%.

Jan 1, 1995

By E. J. Schneider

In view of the growing commercial interest In the higher boiling fractions of low-temperature tar, a study of the literature has been undertaken to obtain as many data as possible regarding the properties of possible pure constituents. The following substances have been studied: THREE-ORTHO-XYLENOL (1, 2-DIMETHYL-3-HYDROXYBENZENE) Detection By the isolation of the silver salt of 1, 2-dimethyl-3-phenoxyacetic acid.

Jan 1, 1930

By John D. Spencer

Research on the development of new and improved methods for the discovery and production of oil and gas and production of fluid fuels from coal continued to be the major thrust of the Bureau of Mines energy research program during 1973. Crude oil recovery from tar sands and oil shale also retained a high priority in this work. Complementing this program were numerous studies aimed at accomplishing the objective of increased energy output with greater safety and minimum harm to the natural environment. This report summarizes research objectives and results and itemizes formal publications of the Bureau of Mines on energy and related subjects.

Jan 1, 1974

By Lex B. Golden

The purpose of this investigation was to evaluate the corrosion properties of certain alloys of titanium and to compare them with those of unalloyed titanium. Such information should make it possible to determine the desirability of substituting these alloys for commercially pure titanium in certain applications. Titanium-manganese, titanium-chromium-iron, and titanium-vanadium-iron alloys, with 2 types of unalloyed titanium, I consolidated by arc melting and the other by powder-metallurgy techniques, were included in the study. Tests were carried out in sulfuric, hydrochloric, phosphoric, nitric, and mixed acids and in chloride solutions. All solutions were saturated with air.

Jan 1, 1957

By C. E. Jordan

Abstract. The U.S. Department of the Interior, Bureau of Mines, as part of its effort to maintain an adequate supply of minerals and metals to meet national economic and strategic needs, is conducting research on the pneumatic recovery of coarse mica. A system of crushers, screens, and zigzag air classifiers is used to concentrate coarse liberated mica particles from mica ore and from the waste tailings of abandoned mica operations. The plus 0.21-millimeter-size mica is effectively recovered by this method. The mica concentrates produced contain over 90 percent mica. The method recovered up to 78 percent of the mica in the samples. As a dry concentration method, the pneumatic-beneficiation technique may be advantageous in areas of limited water resource.

Jan 1, 1980

By C. O. Swanson

CALCULATING the average grade of a gold deposit is a problem that presents certain unique difficulties. Particularly troublesome is the fact that the average of the samples taken from a deposit is likely to be higher than the grade of the ore that is eventually mined, even when allowance is made for dilution and other factors resulting from the mining operations. It would seem that this situation is due to the presence in the deposits of structural peculiarities which have not been properly taken into account, since estimating the average grade of the broken ore produced from the deposits does not present the same difficulty. It is therefore evident that structural considerations are of prime importance in estimating the grade of a deposit. This fact is clearly realized and taken into account in cases where the boundaries of the orebodies and the variations within them are easily recognized. But in many gold deposits this condition is not satisfied, a circumstance which can be regarded as the main source of difficulty. Lacking definite information concerning the structure, we are apt to use certain procedures which are either empirical or based on general probabilities.

Jan 1, 1945

By R. L. Braun

In situ chemical mining of primary sulfide ore requires distribution of injected oxygen in a large underground flooded region of broken ore. Although the maximum oxygen content of the leach solution will be dictated by the operating temperature and hydrostatic pressure, the actual oxygen content will be limited by the geometric dispersion of the injected oxygen, the rate of dissolution of oxygen, and the rate of convective circulation of oxygenated solution within the flooded bed of ore fragments. These factors are examined by a detailed theoretical analysis supported by laboratory experimental data. Typical results of the study illustrate that adequate dissolution of oxygen and circulation of oxygenated solution can be obtained in a column of 4 million metric tons of broken ore by using three gas injection lines and an oxygen injection to consumption ratio of 1.84.

Jan 1, 1974

By D. R. Hudson, M. J. Donaldson

"Study of gravity concentrates from the gold-recovery circuit of the Kambalda nickel mill has enabled an assessment to be made of the nature, relative abundance and compositional variability of platinum group element (PGE) minerals and other associated heavy minerals that are present in the Kambalda nickel deposits. The major platinum minerals are sperrylite, PtAs2, and nioncheite, (Pt. Pd, Ni)(Te, Bi)2, and the major palladium minerals are sudburvite, (Pd, Pt, Ni)(Sb, Te, Bi), stibiopalladinite, Pd6Sb2, and palladoarsenide, Pd2 (As, Sb), together with a palladium antimonide and a palladium arsenide that have not been fully characterized. Palladian melonites, which contain up to 10 wt% Pd, and palladian nickeline are also important PGE hosts. Sperrylite and sudburyite are by far the most abundant discrete minerals in the gravity concentrates.Gold occurs as argentian, cuprian and nickeloan—cuprian gold, and as the tellurides calaverite, petzite and auriferous hessite. Silver is present in petzite, hessite and volynskite. Other rare phases contained in the gravity concentrates include native bismuth, altaite, frohbergite, breithauptite, gersdorffite, parkerite, scheelite, tantalite, cassiterite, rutile, bunsenite, gahnite, barite and uvarovite.Descriptions of in-situ occurrences of PGE minerals at Kambalda are rare. Michenerite, PdBiTe, and testibiopalladite, PdSbTe, have been described from a telluride-rich quartz-carbonate vein that intersects massive sulphide ore in Lunnon Shoot. Moncheite has been observed in chalcopyrite-rich stringers, and sudburyite occurs as inclusions in nickeline in a quartz- carbonate veinlet. No discrete PGE minerals have been found within the massive and matrix ore zones in the Kambalda ore- shoots, and the geochemical distribution of PGE suggests that the formation of discrete PGE phases may be related to post- magmatic processes—in particular, metamorphic segregation of sulphides, and the interaction of the ore sulphides, containing PGE in solid solution, with younger hydrothermal fluids. This has led to local redistribution of the PGE, with concentration in footwall stringers and veins, and in reaction zones."

Jan 1, 1984

By Rajashekhar Marthi

Lithium is a key component for future electric vehicle batteries and energy storage. The future availability of lithium to meet the growing demands remains in question. Around 60% of lithium resources exist in the form of continental brines. Traditional methods to recover lithium from brines use solar concentration with precipitation and have found limitations in lithium extraction due to interference of Mg in high Mg/Li brines. Thus, there is a need for highly selective adsorbents. Recently, spinel structured delithiated lithium manganese oxides have demonstrated promising results. However, due to the small particle sizes, it is economically difficult to recover the adsorbents and thereby limits industrial applications. In our work, LiMn2O4 ion sieve was synthesized and immobilized on diatomaceous earth. Fundamental adsorption studies were carried out in lithium buffer solutions to understand the nature of adsorption and kinetics. The adsorbents were also tested for recycle stability, as well as recovery of lithium from Great Salt Lake water samples.

By Eric Forssberg, Vigen Zeng

During mechanical grinding high intensity vibration is emitted that contains information on the mill's operating state. Tests, using a laboratory ball mill, studied the influence of operating parameters on the vibration signature. The parameters studied were: mill speed; powder filling; pulp density; grinding period; and pulp temperature. Vibration signals were detected by an accelerometer, amplified by a vibrometer and recorded onto digital audio tape. A digital oscilloscope converted the signals into IBM-compatible data format. Digital signal processing and multivariate data analysis were carried out with specially developed software. The power spectral density was estimated from the time-domain vibration signal. Four new latent variables were used to describe changes in the vibration spectra. A relationship was established between operating parameters and latent variables which could form the basis of a quick and automatic method of monitoring operating parameters in ball mill grinding.

Jan 4, 1993

By P. K. Koh, L. S. Birks, J. M. Siomkajlo

Direct identification in situ of x and a phase precipitates in stainless steel is possible with the electron probe microanalyzer. Although particles in the 1 p size range are too small to yield absolute percent composition, the relative % Crfi Mo ratio can be used to distinguish the two phases with better than 95 pct confidence. Wet chemical analysis of extracted residues gives Cr/Mo ratios in good agreement with electron probe results extrapolated to the 4 to 5 p size range. WHEN stainless steels are subjected to extended heating in the temperature region around 1600°F, precipitation of the brittle 0 or x phases may occur and impair the properties of the material. Identi-

Jan 1, 1961

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct- to-Blister process design.

Jan 1, 2003

By R. Tomás, J. B. Serón, M. Romana

The Slope Mass Rating (SMR; Romana, 1985) geomechanics classification was developed as a sequel of Bieniawski’s Rock Mass Rating (RMR) system, which was almost impossible to use in slopes due to the extreme range of the correction factors (up to 60 points of a maximum of 100) and to the lack of definition of them. A detailed quantitative definition of the correction factors is one of the advantages of SMR classification. During the last thirty years the use of SMR system has been extended to many countries from the five continents and, thus, it is time to review the most interesting developments. Both RMR and SMR are discrete classifications, depending on the values adopted by the variables that control the parameters. This can cause major changes in the parameters value due to small differences in the variables value, with changes in the final rock mass assigned quality. On the other hand, geomechanics quality indexes are extremely biased. To avoid this problem, some authors have proposed continuous functions for SMR. This classification has been also adapted for its application in heterogeneous and anisotropic rock masses, for high slopes, for is application trough stereographic projection and Geographical Information Systems, has been used as susceptibility rockfall parameters and has been included in the technical regulations of several countries. Additionally, some open access computer tools have been developed for the computation of SMR. Consequently, this paper reviews: 1) the most important modifications and adaptations of slope classifications which derive directly from SMR; 2) the use of SMR throughout the world; 3) many significant papers on slopes analysed with SMR all over the world; and 4) future trends in the use of SMR.

Jan 1, 2015

By A. K. Kyllo, N. B. Gray, B. N. McCurry

"Dynamic control of the formation of a solidified layer between a pipe wall and a flowing melt enables the flow rate to be adjusted in real time. This solidified layer can be generated by using a coolant on the outside of the pipe wall to remove the required heat. The coolant, and hence the solidified layer, can be controlled remotely. The dynamic behaviour of the solidified layer was investigated by both physical experiments and mathematical modelling. The mathematical model has been developed using a finite difference technique to describe conduction through the pipe wall and solidified layer. Results from the model were consistent with previous steadystate experimental results using molten lead. Experiments are currently being carried out using molten tin in a recirculating circuit with a cooling system that is instrumented for accurate computer control to validate the model. The circuit is designed for flowrates of up to 24 kg/s (86 tph) of molten tin. Steady-state and dynamic predictions were made for the current rig.Industrial SignificanceThe current method of choice for tapping slags, metals and mattes from many metallurgical furnaces is using an oxygen lance to open the taphole and using a clay plug to close it. There are, however, some significant drawbacks in this method. The heat generated by the oxygen lance erodes the refractory lining of the taphole, as well as the clay plug, and the furnace products themselves corrode the taphole. Using an oxygen lance is also a significant safety hazard to the operators as they must work in close proximity to the furnace and be subjected to a shower of sparks while opening the taphole. Also, the flowrate of material through the taphole cannot be controlled online as the diameter of the opening cannot be varied easily. This feature means that the level of product in a furnace cannot be kept constant."

Jan 1, 1999