Search Documents

By Türker Hüdaverdi, Özge Akyildiz

"In this research, image analysis technique, Kuz-Ram and KCO Models were used to examineefficiency of the quarry blasts. Investigations were performed in Cendere region, Istanbul. As a firststep, image analysis software was used to determine particle size distribution of muckpiles.Additionally, the results of KuzRam and KCO fragmentation models were compared to the results ofthe image analysis technique. The efficiency of KuzRam and KCO models was investigated and theimportant points to be considered were explained. Additionally, the effect of the rock factor valueson the size distribution curves was investigated. The blasthole diameter is 89 mm. (3.5 in) in thestudied quarry. Each measured blast has a different burden, spacing and stemming length. Blastholes was drilled in a staggered pattern. It is concluded that, KuzRam and KCO models can be successfully used to determine fragment size distribution in Cendere Region Quarries, Istanbul. Site engineers can predict blast fragmentation using the theoretical fragmentation models and they may change blast design parameters before blasting operation if necessary. It is possible to calibrate the Kuz-Ram and KCO fragmentation models using the measurements obtained by image analysis technique."

Jan 1, 2016

By Hung-Kei H. Lam

Rubidium and cesium were discovered by Bunsen and Kirchhoff about 100 years ago. These two elements are by no means as abundant as sodium or potassium. Their occurrence in minerals is widespread, but usually as minor constituents. There is no known specific ore containing rubidium, but rubidium is found replacing the. other alkali metals in .some minerals.. Perhaps the highest concentration of rubidium found in one mineral is in lepidolite, KLi(OH,F)2A12Si3010, which contains from 0 to 3.5%*Rb20. 0n the average, lepidolite contains about 0.5% Rb20. Other sources of rubidium are carnallite, KMgCl3?6H20; pollucite, H20.2Cs20.2AI203.9SiO2; rhodizite, R20.2A1203-3B203; biotite, H2K(Mg,Fe)3A1(Si04)3; sea water, rivers, marine and fresh water organisms, soils, and plants. Cesium, even though it is the least abundant. of the stable alkalies, has a specific ore. Pollucites a hydrous cesium aluminum silicate, may con¬tain as high as 42.5% Cs20, although again, the average Cs20 content is about 25% among the handful of known deposits. Other cesium-containing minerals are lepidolite and carnallite. Rubidium and cesium are very much like potassium in chemical properties, consequently, they are hard to separate. Because of the difficulty in obtaining pure cesium and rubidium compounds coupled with the scarcity-of supply, prices were high and the two elements enjoyed little industrial use. Just before the Second World War, the world. supply of rubidium and cesium, from Germany, was a matter of tens of kilograms per year and prices were about

Jan 1, 1959

By Scales PJ, Ralston J

Fine coal particles have been examined with respect to dustiness and its connection with various physical and chemical properties. It appears that a given coal will tend to be dusty ifthe moisture content is low and if the inert maceral content and overall rank are high. The hydrophobicity ofa coking coal (Young-Wallsend) and a steaming coal (Blair Athol) was examined in detail by a dynamic contact angle technique. The YoungWallsend coal had a higher contact angle, on average, than the Blair Athol sample. This result has important implications for dust suppression and associated processes.

Jan 1, 1986

Mining at Waihi on the Martha Hill commenced in 1878 and between 1892 and 1953 produced 35 million ounces of bullion from some 13.5 million short tons of ore from 40 named quartz reefs. The general geology of the ore is recorded in detail with differing interpretations by Bell and Fraser (1912) and Morgan (1924). The reefs and stringers have formed by fissure filling and replacement in mainly quartz andesite dacite flows within the Waihi 'Graben'. The host rocks are extensively propylitised with intense alteration forming zones of kaolin adjacent to the main reefs.

Jan 1, 1979

By John Dasher

Getting spodumene to float quickly and cleanly can be a problem. The author has presented an excellent account of a valid and useful approach to the scale-up of such problem floats. This indicated advantages for doubling retention time, i.e., buying another set of flotation cells. The author states that 21 pct of the spodumene floated in 2 min in the laboratory cell, that the grade of the rougher was about 75 pct spodumene, and that the final tailing contained 4 to 12 pct spodumene in different sizes with the present cells and 1 to 9 pct spodumene with twice as many cells.

Jan 6, 1959

By Hibbert W. D, Lottrey A

The behaviour of coal in a process is a function of both the coal properties and the processing conditions. In the case of the Loy Yang coal deposit, extensive testing has been undertaken to determine: ò the extent, distribution and structure of the coal resource; ò the variations in properties throughout the resource; and ò evaluation of the behaviour of the coal during processing. This has involved the conduct of an extensive borehole drilling program, backed by geological modelling and material characterisation (chemical, physico-chemical and petrological). Evaluation of the behaviour of the coal during processing has ranged from theoretical modelling, laboratory-scale investigations through to pilot scale and full-scale tests. Until recently, the bulk of the work was directed at evaluating the behaviour of the coal for existing pulverised fuel (pf) firing/steam boiler technology and a high level of understanding has been developed of both the coal resource and its behaviour within these systems. More recent efforts have been directed towards the evaluation of new technologies directed towards cheaper and more efficient power generation using this coal. Loy Yang coal has been evaluated in the following technologies: ò Hydrothermal dewatering/direct coal-fired gas turbine; ò Steam fluidised bed drying; ò Solar drying/densification; ò Briquetting; and ò Gasification.

Jan 1, 1992

By M. Sinirkaya

The dissolution process of phosphate rock from the Semikan area (Mardin-Mazidagi, Turkey) using dilute phosphoric acid has been investigated. The work involved studying the effect of important variables, such as reaction time, stirring speed, particle size fraction, phosphoric acid concentration and temperature. Van der Sluis et al.?s model was used to determine the rate of the partial dissolution of phosphate ore. Mass-transfer coefficients (kL) varied between 2.8 and 28.5.10-3 m.s-1. The activation energy of the process varied between 16 and 20 kJ.mol-1. It has been found that the dissolution process is controlled by calcium ion diffusion, rather than by chemical reaction.

Jan 1, 2010

By J M. F Clout, E Donskoi

The ability to design a beneficiation process for a new orebody based on particular feed characteristics is a powerful and practical tool. A new technique has been developed where beneficiation outcomes can be calculated by combining feed size-by-size chemical analysis, mineralogy, liberation and particle characteristics with a series of simple theoretical unit separation models rather than a simple mass balance approach or an exhaustive beneficiation test program. The new technique provides the ability to rapidly identify ore types that have the potential to meet product specifications whilst also rejecting others that will not meet specification even if a perfect separation was achieved. Beyond the broad scale decision making process, practical mineral separation curves from actual plant data can be used to more closely simulate the proposed process. This approach reduces the amount of laboratory and pilot plant work necessary by targeting what process stages will be required, increases early rejection of uneconomic options, identifies problematic ore types or unit operations and is a step towards estimation of final grade and recoveries achievable in potential circuit configurations.

Jan 1, 2004

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By M E. Pierce, T V. Garza-Cruz

Rock mass strength and brittleness generally have a significant impact on both cavability and fragmentation. Variability in these properties across a panel or block footprint is of particular interest because stronger units have the potential to significantly impact cave shape. This paper describes how FLAC3D™ was used to examine the impact of variability in rock mass properties on predicted cave performance to aid in assessing potential risks associated with the proposed design.A case study orebody was subdivided into a number of domains to reflect the heterogeneity of the rock mass at the scale of a proposed inclined cave. The results suggest that the presence of stronger units has the potential to impact cave shape significantly in the southern half of the cave footprint and could increase the potential for cave stalling at shallow depths. If this unit is stronger and less brittle than expected, an overhang is predicted to develop in the southern half of the inclined cave at depth. The effective hydraulic radius is significantly reduced due to the overhang in the south, and the cave could eventually stall at shallower depths in the north.CITATION:Garza-Cruz, T V and Pierce, M E, 2016. Impact of rock mass strength variability on caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 359–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Claude Bazin, Jalna Lamontagne

"The operators of mineral processing plants collect daily samples from strategic process streams with a view to prepare production balances to assess plant performances. The rules to minimize the risk of systematic sampling errors are known and applied in many mineral processing plants. The mass of the sample to be collected is calculated to yield a target measurement reproducibility considering the fundamental error associated to the sampling of heterogeneous material. This paper demonstrates that this practice is partly valid if one does not account for the time variation of the ore composition during the day. The concept is demonstrated using samples collected on a 30 minute basis from different streams of a gold ore concentrator. Results show that depending of the natural variability of the stream characteristics the mass of the daily samples may not be the critical variable to obtain reproducible measurements. On the other hand the number of cuts taken during the day could impact on the variance of the measurements obtained from daily samples.IntroductionMineral processing plants may treat several thousand tons of ore every day to produce concentrate or impure gold ingots. The operation and performances of these plants are monitored on a daily basis through the collection of ore samples from various streams of the processing circuit. The samples are prepared and assayed to obtain the concentrations of target elements that are subsequently used to calculate the mass flowrates in the streams of the circuit and ultimately the distribution of the target metals for the estimation of the plant performances (Morrison, 2009; Lachance and Leroux, 2016).The acquisition of representative and reproducible samples is therefore the first step in the characterization of plant performances. The term representative sample is used here to indicate an unbiased sample, i.e. a sampling procedure that does not introduce a systematic error. Rules for the collection of unbiased samples are reviewed in the literature by different authors (e.g. Morrison, 2009) and are not discussed in this paper. The term reproducible indicates the dispersion of the measurements around the average value of a characteristic of a stream meets an acceptable level of variance. The reproducibility of a measurement process (sampling and analysis) is assessed by the relative standard deviation or coefficient of variation of the measurement that is a function of the sampling and assaying errors (Morrison. 2009; Gy, 1979). Usually the focus is put on the fundamental error of sampling whose variance can be controlled by the choice of the primary sample mass or adequate particle size reduction during the preparation of secondary or tertiary samples extracted for the chemical analysis. When a sample is taken from a stream that exhibits a time varying characteristic, the obtained measurement exhibits a variability that is not only a function of the sample mass but also of the natural variability of the ore in the sampled stream. This paper examines this aspect of the sampling of a time varying process on the reproducibility of composite samples for a day of production."

Jan 1, 2017

By Peter T. Luckie, Harold L. Lovell, E. R. Palowitch, A. W. Deurbrouck, James K. Kindig

PART 1: DENSE MEDIUM SEPARATION by E. R. PALOWITCH and A. W. DEURBROUK INTRODUCTION During 1965, 64.9 percent of the 512 million tons of bituminous coal and lignite produced was cleaned mechanically, of which 95 million tons was cleaned by dense medium processes.l The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes rose from 7.0 to 28.5 percent from 1938 to 1965. Dense medium separations include those coal preparation processes which clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes offer the following advantages over other coal cleaning processes : 1. Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of the feed in the range of e 0.1 specific gravity units. 2. Ability to maintain a separating gravity that can be controlled with ±0.005 specific gravity units. 3. Ability to handle a wide range of sizes (up to 14 inches). 4. Relatively low capital and operating costs when considered in terms of high capacity and small space requirements. 5. Ability to change specific gravity of separation to meet varying market requirements. 6. Ability to handle fluctuations in feed both in terms of quantity and quality. HISTORY Sir Henry Bessemer patented the first dense medium process in 1858. Solutions of the chlorides of iron, manganese, barium and calcium were proposed as separating liquids; the separation was made in a cone-shaped separator. One large-scale plant using calcium chloride was erected in Germany but soon was abandoned. The Chance process, using a mixture of sand and water, was first

Jan 1, 1968

By K. N. Karparov

The classical limit equilibrium methods are suspected to be ineffective in predicting the potential for highwall failure in many instances in coal mines around the world. Slope engineers have for many years recognized a block thrust failure mechanism for slope failures, but little work had been done before 2000 to explain the actual mechanisms which must be responsible for the failure. The main reason for this is that limit equilibrium methods implicitly assume rigid blocks, and the resulting force equations must be satisfied everywhere simultaneously for them to have any meaning. This paper will show that the material involved in the slope failure is not rigid; indeed it undergoes considerable permanent deformation during failure. This observation allows the authors to treat the block boundaries independently, because they need not maintain a constant spatial relationship with one another, as is assumed in other methods. To enable analysis of this type the authors assume that the weight of the blocks is evenly distributed. This is reasonable, because the slope material is not strong enough to be self-supporting without some sort of constraint, or strong enough to be able to apply point loads to the surrounding material. The purpose of this paper is to extend the practical application of the analytical method developed from mechanism studies to provide an objective assessment of the risk of slope failure, and therefore guidelines for more stable slope designs. This work is based on studies carried out on two failures in an open pit coal mine in South Africa, and provides a methodology to assess the potential for failure more objectively than is possible with currently accepted methods, while at the same time remaining sufficiently simple to allow a ?back of the cigarette box? assessment by geotechnical engineers on site.

Jan 1, 2009

THE Taranaki oil-field is situated on the western side of the North Island of New Zealand, at about its widest part, and may be said to be the most compact and fertile part of the Dominion, for, with the exception of the upper half of Mount Egmont and of the ranges adjoining, which absorb 36,000 acres, the whole of the area, minus what is taken up by the rivers and streams is suitable for settlement, and certainly two-thirds is good land. The gross area of the district is 2,417,299 acres. The principle rivers are the Wanganui, Mokau, Waitara, Patea and Waiwakaiho. Mount Egmont, which is 8260 ft. high, used to be called Taranaki, and from it the district takes its name (the Maori meaning of which is "sloping peak ").THE OIL-FIELDThe discription of an oil-field now-a-days usually resolves itself into a mass of figures and statistics, of great interest and value to the engineer and commercial man, but practically indigestible to the general public. It is the realm of the financierand the captain of industry.

Jan 1, 1912

By Frank B. Amon

Highland Valley Copper had to make some significant changes in the way it was working in order to counter the effects of ever-increasing costs and decreasing metal prices. A mine/mill optimization plan started in 1997 introduced new technologies and management approaches that resulted in a dramatic drop in cash breakeven costs. The changes involved employee training, added authority and responsibility for staff, better communications, and a consistent approach to setting and achieving property-wide goals. The net effect was to change the culture of the organization from one that was fragmented and focussed on local objectives to one that is cohesive and has common goals. These changes have allowed the mine to remain in business during a protracted period of low metal prices, and have positioned the mine favourably to benefit even more from any future increase in prices.

May 1, 2004

By Rex E. Loesby

The marble deposits of Yule Creek were first discovered in the late1870s. Minor quarrying occurred between that discovery and the early 1900s. Major development occurred in 1905, when Channing Meek, with some help from the Rockefellers, raised $3 million to develop the Colorado Yule Marble Quarry. That is $50 million in today’s dollars. Some of the words used to describe the marble deposit were “gigantic, remarkable, flawless and immense.” Boosters proclaimed, “The marble age is here.” Obviously, dreams were big for Marble.

Jan 1, 2003

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

The following is an incomplete list of members and guests who called at Institute headquarters during the period Feb. 10, 1918 to Mar. 10, 1918: W. G. Anderson, St. John, N. B., Canada. Charles E. Locke, Boston, Mass. L. M. Banks, Camp Meade, Md. E. T. Lednum, Joplin, Mo. P. E. Barbour, Albany, N. Y. C.' K. McDonald, Washington, D. C. Alan M. Bateman, New Haven, Conn. C. T. Malcolmson, Chicago, Ill. Graham Bright, Pittsburgh, Pa. Stuart B. Marshall, Badin, N. C. J. F. Callbreath, Washington, D. C. T. C. Merriman, New Haven, Conn. J. E. S. Clark, Riverside. Cal. Arvid E. Nissen, Gary, Ind. G. H. Clevenger, Palo Alto, Cal. Herbert G. Officer, Conway, S. C. George C. Crossley, Trenton, N. J. J. E. Parker, Bulawayo, Rhodesia, S. Afr. R. H. Eagles, Palmerton, Pa. Francis R. Pyne, Elizabeth, N, J. Charles Enzian, Pottsville, Pa. Alfred Hull Ramage, Joplin, Mo. Albert H. Fay, Washington, D. C. H. H. Stoek, Urbana, Ill. David B. Gemmill, Crown King, Ariz. G. M. Taylor, Colorado Springs; Colo. Ronald Harris, London, Ont., Canada. Charles Tubby, St. Paul, Minn. Wm. J. Hayes, Colombia. So. America. J. B. Tyrrell, Toronto, Canada. B. B. Hood, Chrome, N. J. Edmund W. Westervelt, Ymir, B. C. 0. P. Hood, Pittsburgh, Pa. Carl Zapffe, Brainerd, Minn. H. M. LaFollette, LaFollette, Tenn. W. S. Boyd, formerly superintendent of mines of the Ray Consolidated Copper Co., has been appointed assistant general manager. William Campbell, Professor of Metallurgy, at Columbia University, is acting as metallurgist at the New York Navy Yard.

Jan 4, 1918

Gold in the stibnite veins of Costerfield, Victoria, was described in 1922 1, prior to any mineragraphic examination, as (a) free yellow gold (b) free rusty gold and (c) combined gold. The free yellow gold occurs in quartz and will amalgamate with mercury. The free gold of dull, rusty or copper-red colour occurs in massive stibnite and has been stated to resist amalgamation with mercury. The dull colour is only skin deep and the colour is bright when the rusty gold is scratched. The appearance of the rusty gold is spongy or cellular and it generally occurs near small cavities in the stibnite. The suggestion that the cellular character indicated the removal of a certain amount of stibnite leaving a residue of se.condary gold cannot be sustained.It now appears probable that the rusty gold is formed by the primary dissociation of a gold antimonide and is distinct in origin from the normal yellow gold which is deposited with quartz or stibnite from auriferous mineral solutions.The combined gold referred to in the earlier paper was the gold contained in the stibnite as revealed by assay. Such gold was at first thought to be either dissolved in the stibnite or else present as free interstitial particles too minute for observation in transmitted light in thin sections.Subsequent examination of numerous polished,surfaces disclosed the small particles of gold occurring in the grain boundaries in aggregates of fine grained stibnite 2. The assumption that all the gold in the stibnite, as revealed by assay, occurred in this way is now known to be incorrect, because limited amounts of a gold antimonide have been found in the veins.

Jan 1, 1952

By R. P. Sloan, A. S. Whitford

In November 1999, CCI's Empire Iron Mining Partnership and MinnovEX Technologies Inc. developed an expert system for advanced control of their Empire IV Grinding Section. Empire IV is comprised of three autogenous Primary Mills and six autogenous Pebble Mills, with a single Pebble Crusher and high pressure Roll Press. The challenges of controlling and optimizing three distinct grinding lines that are inter-woven by a pebble crushing circuit were met with innovative and unique solutions. This paper will detail the approach employed at Empire and will focus on the aspects that make this application unique.

Jan 1, 2001