Search Documents

By R. W. Young, Arthur F. Taggart

The tests herein described are part of an extended series of expel<ments, performed by the authors together with J. F. McClelland and L. W. Bahney, on the reclamation of metallics from foundry and manufacturing-plant scrap. The most obstinate problem encountered was the proper cleaning of the metal. Introduction In the manufacture of brass and brass products the weight of the finished product leaving the plant is much less than the total weight of. copper and zinc entering. A small part of this discrepancy is due to the unavoidable oxidation of the metals in melting, but by far the largest part of the loss is in the form of metallic particles of copper,. zinc, and brass. These losses occur principally at three points in the process: (a) in the casting-shop ashes; (b) in the slags from furnaces melting scrap brass; (c) in material spilled on the floor throughout the manufacturing process. The amount of these products in some plants is nearly 100 tons per 24 hours. Casting-shop ashes contain the metal spilled from the crucibles during melting and pouring, and the metal included in the slags formed in the melting process. The ashes also contain pieces of broken crucibles with adhering metal; 20 to 30 per cent. of unburned coal is also present. The metal in casting-shop ashes contains clean pieces of zinc or copper ingots weighing 1 to 2 lb., jagged pieces of metal of all shapes ranging in size from several inches down to the finest dust, and shot and botryoidal shapes ranging in size from 2 or 3 in. down to 0.01 mm. or less in diameter. Slags from furnaces melting scrap brass contain metal in the form of small shot. Floor sweepings occur in all shapes: spirals, thin shavings, pins and pin-like pieces, wire, rods, and buffing-wheel dust are the commonest.

Jan 1, 1916

By Heric Henrique Souza e Silva, Johne Jesus Mol Peixoto, Natalia Barros Barony, Itavahn Alves da Silva, Weslei Viana Gabriel, Carlos Antonio da Silva, Varadarajan Seshadri

In this work the circulation rates have been determined in a 1:7.5 scale physical model of RH reactor (Ruhrstal Heraeus) and using oil/water and oil/zinc chloride solution to simulate steel melt/slag in the prototype with the objective of evaluating the influence of density and viscosity on the entrainment of oil simulating slag. A technique based on strain gage bridge and particle image velocimetry was developed to assess the circulation rate, as the usual tracer method is not feasible due to the presence of chloride ions in ZnCl2. The critical velocity and critical diameter of oil drops for slag (oil) entrainment in water/oil and ZnCl2/oil systems were estimated using equations from the literature. Due to the difference in density, the ZnCl2/oil system, showed a critical velocity that is 28% higher than the silicone oil/water system while the maximum size of the entrained droplets was about 65% lower than that for water/oil system.

Mar 1, 2017

By R. Le

"The principles of noise control aredescribed with particular emphasis on personalactive units as opposed to passive ear muffspresently in general use. A discussion followsfor their potential use in a mining environment.RÉSUMÉNous décrivons brièvement quelquesprincipes de contrôle de bruit à l’usage person-nel, puis nous passons en revue quelquescasques commerciaux dotés de ces circuits àprincipe actif. Enfn nous discutons de leurusage potentiel dans le contexte minier.IntroductionLe casque à principe actif est un produitqui existe commercialement, mais encore peurépandu en usage, sûrement à cause du prix,mais aussi de sa méconnaissance par le grand public. Il arrive parfois qu’un journaliste trouvele produit fantastique et le médiatise commeune réalisation de son pays (ou de sa province),mais peu savent qu’il s’agit là d’un principe quia commencé dans les années 30. Par delà lesensationnel, il reste que si l’on veut mettre lamain sur un de ces casques pour l’essayer, on nesait où l’obtenir. De plus, les casques n’utilisentpas tous le même principe actif. C’est la raisonpour laquelle nous faisons cette brève compara-ison. Nous le faisons en mettant l’accent pourune possible utilisation dans le domaine minier,car c’est dans ce milieu que les usagers sontconfrontés aux bruits les plus intenses qui peu-vent endommager leur système auditif, ce quin’exclut pas les autres situations (travaux publics, foresterie, écoute hi-f, etc.)."

Jan 1, 1997

By M Jones

The past 100 years the mining industry can be characterised by a focus on increasing financial returns often to the detriment of social, human, manufactured and environmental capitals. Despite the sustainable development principles promoted by the International Council on Mining and Metals (ICMM), the Equator Principles and the African Mining Vision, which should have enhanced project promoters’ ‘licence to operate’ within a host community or nation, the industry has often failed to integrate proven innovations and best practices that enhance sustainability outcomes for mineral resource projects. This failure has led to delays, the abandonment of projects, with value destroyed for promoters, governments, host community and investors.The paper will outline the application of proven innovations, Enterprise Optimisation (EO), and Sustainable Operations (SUSOP&#174;), during the pre-feasibility phase of a project. By determining the value of each capital before and after the application of proven innovations, the presentation will outline how and where value can be created across all five capitals over the life of a project or operation.The paper will demonstrate how the application of proven innovations significantly transforms the value-proposition of a mineral resource project or operation by generating additional value across all of the five capitals, reducing project risk, thus generating value for all stakeholders.CITATION:Jones, M, 2015. Fundamentally transforming the economic and sustainability signature of mining assets, in Proceedings Third International Future Mining Conference, pp 169–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Harry E. Holzschuh

The two Agrico Chemical Company self unloading Phosphate Rock barges put into service in 1976 operate at over their design carrying capacity. Each barge now carries 26,000 short ton instead of the planned 25,000 short ton at 32 foot of draft. They are in service between Agrico&apos;s Tampa, Florida Terminal and the Donaldsonville, Louisiana Fertilizer Complex, moving a total of 2,500,000 short tons each year. This was the first use of the Parascrew design for a marine application. The barges, with their 3,000 STPH unloading and matching loading rate is the vital link in this total transportation and handling system. Rock is moved from the Pierce, Florida Mines through the Tampa Big Bend Terminal, across the Gulf of Mexico, and up the Mississippi to the Agrico Faustina Phosphoric Acid Plant 30 miles below Bacon Rouge, Louisiana. The trip from the terminal to the plant is 600 miles and the turnaround time is just about six days. Seven years operating experience has proved that the system works. Fittingly, the two barges are named the "Faustina" and the "Pierce". They have a beam of 85-feet and are 495 feet long. folded depth is 43 feet, with a ballasted light draft of 19 feet and a typical loaded draft of 32 feet. There are four separated holds with the machinery room located forward of 101 hold. Each hold is 51 feet wide at the coamings with an 18 foot straight section on the side, and a 24 foot long, 600 slope sheet for a 23 foot clear reclaim width at the bottom. The Parascrew in each of the holds is 37 feet long between the bearings and is supported on a 14 inch diameter hollow shaft. The screw pitch varies and the diameter of the flights step up from l&apos;-9" diameter to 2&apos;-6" diameter on the discharge end. By sloping the centerline, a minimum four inch bottom clearance is maintained across the hold. Some bending of the tube does take place.

Jan 1, 1983

Olympic Dam Operation is located in the Stuart Shelf Geological Province approximately 520 km north-north-west of Adelaide in South Australia. It is estimated to be one of the worldÆs top five copper orebodies by size and the biggest single occurrence of uranium. The deposit was discovered by Western Mining Corporation in 1975. Exploration was based on a conceptual model for the formation of sediment hosted copper deposits together with gravity and magnetic anomalies.The capital cost of the current expansion is estimated to be A$ 1.64 billion. The underground expansion includes a total of 36 km of lateral development, a railway haulage system delivering ore from a series of ore passes to a new crusher station and a significant increase in ventilation capacity and mine services.In the current underground expansion the mining method will essentially remain unchanged. The ore handling system will incorporate some recent advances in technology, improving efficiency and safety standards.Major infrastructure excavations are designed by a team of engineers attached to the Olympic Dam Expansion Project and a number of consulting groups. Once the expansion is fully completed it is expected to increase the current annual underground production level from 3.4 Mt to 9.0 Mt of ore by the year 2000. Mine design engineers working for the Olympic Dam Operation have recently completed a three year final design plan to achieve this target.Access to the existing mine is through the decline and Whenan shaft. The Whenan shaft was originally sunk as an exploration access and later upgraded for hoisting. The 4 km long service decline connecting to the Whenan shaft was later constructed to accommodate the increase in service demand. The Robinson and Sir Lindsay Clark shafts were developed at later stages to cater for the hoisting during and following the expansion lead up.

Jan 1, 1999

By Albert C. Harding

For several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. Description Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare wither-ite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. Occurrence All known commercially important barite deposits in the United States occur as re- placements or cavity fillings in schists, shales, limestones, dolomites, and quart-zites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. Table i—Crude Berile Sold or used by Producers in 1945 State Short Tons Arkansas................... 260.660 Missouri.................... 225.467 Georgia..................... 110,393 Tennessee................... 32,812 Nevada..................... 28,919 Other States............... 37,811 Total..................... 696,062 (&apos;other states,, included only california and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. Consumption The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium ------- chemicals Total 720,903 tons

Jan 1, 1949

By J. H. Frye, R. M. Treco, J. W. Caum

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."1 It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data 2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. HARDNESS, LATTICE PARAMETER AND IONIC OVERLAP Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2, It is believed that most of the values are accurate within the limits indicated by the rectangles, These data are also presented in Table I. Ultimate Meyer hardness, Pu, is defined by the equation: [P" - D2] where L = load, D = diameter of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro¬duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. [ ] The question arises as to whether or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

By R. L. Grant

"Carbon dioxide has been used for extinguishing electrical fires of many kinds (1, 3, 4) 3/ and more recently has been applied to some extent in fighting coal-mine fires (5). This report is concerned with the possibility of an electric current being conducted from a live power source, such as a trolley wire, across the impinging spray of carbon dioxide gas, to a metallic discharge nozzle, and then being grounded through the body of the person holding or touching the container. Rose and. Skinner (5) have described a case in which a fall of roof coal had brought down the trolley without creating a dead shot. The current was conducted in part through the loose coal to the rail, causing ignition of the coal. The fire was successfully extinguished with carbon dioxide.Dielectric data on pure carbon dioxide gas and liquid have been reported by Quinn and Jones (2). For the gas, the dielectric constants range from 1.00971 (35°C., 10 atmospheres) to 1.3072 (70°C., 151 atmospheres); for the liquid, 1.6016 (0°C., 50 atmospheres). Compared with the dielectric constant of air (1.0006, 1 atmosphere), these data, indicate that carbon dioxide in both gaseous and liquid forms is a very poor conductor of electricity, of the same order as air. 4/"

Aug 1, 1942

By Karl J. C. Harries

"1.1. WHAT ARE AGREEMENTS AND HOW ARE THEY FORMED?In order to have an agreement, at common law, there must be an offer, acceptance of that offer, and consideration passing between the parties. In addition, the material terms (i.e. the basics or substance) of the agreement must be discernible, preferably by means of documentation. Although these concepts may appear simple and straightforward, the law relating to them is voluminous and complex. Some brief comments are worthwhile.• Offer/acceptance: Both offer and acceptance should be in writing, but they need not be. The actions, conversations, and/or correspondence of the parties may constitute either or both of them. Notwithstanding, the local law or practice of a jurisdiction will impose some specific requirements for certain types of agreements. If these requirements are not met, the agreement may be unenforceable. For example, Ontario’s Mining Act requires transfers of unpatented mining claims to be evidenced in writing and recorded.1• Consideration: Consideration is usually thought of as being money, but it can be virtually anything, even “the premises” (i.e. the mutual covenants or promises contained in the agreement itself). In addition, if one party, relying upon the offer of another, does something to his detriment, then the doing of the act can be considered to be an acceptance of the offer and, under the legal concept of “detrimental reliance”, can also be consideration. Whether or not detrimental reliance exists will depend upon the circumstances of each case.2• Material terms: The requirement that the material terms of an agreement must be discernible does not mean that all of the terms of an agreement must be documented or even have been considered, just the basic or material ones. In addition, it will be up to a judge to decide what is material – not necessarily the parties. In order to establish the material terms, a Court may look at all relevant documentation and may hear oral evidence. It will resist “writing the agreement”"

Jan 1, 2003

By A. E. Powers

YEARS of experience and research have shown that molybdenum, tungsten, and vanadium are among the most useful and effective elements in augmenting the high-temperature strength of heat-treatable, ferritic steels. Grün, for example, in conducting an early survey of the strengthening effects of various elements in annealed, low-carbon steel at 750° and 930°F (400° and 500°C), found molybdenum and vanadium to be the most effective.&apos; Holtmann comprehensively studied the strengthening effects of molybdenum and vanadium in quenched and tempered steels at 930°F as a function of microstructure and carbon content.&apos; He found creep strength to be related to the saturation of the austenite at the austenitizing temperature, such that strength is increased by alloying until the y loop is reached—the terminus of complete austenitization. Beyond this degree of alloying, the inability to heat treat will result in lower strength, at least for low and moderate creep temperatures. Tungsten, owing to higher cost than molybdenum, has been little used in ferritic high-temperature steels. As a result, very few investigations have been made of its high-temperature strengthening ability, and reliable data on its effectiveness are not available. Grün rated tungsten far less effective than molybdenum at 930°F (500°C) on a weight-percentage basis.&apos; However, Tammann has found that tungsten is as effective as molybdenum in raising the recrystallization temperature of iron. For this reason Smith, in a review of the subject, has advocated a re-examination of the influence of tungsten on the high-temperature strength of steel.&apos; In any study of the effects of alloying additions on high-temperature properties, recognition must be made of the many variables involved, some of which can be controlled but have been ignored in innumerable investigations of the past, and some of which are difficult or even impossible to control. One cannot, for example, assign a definite strengthening index to any one alloying element, for this will be dependent upon the microstructure (heat treatment and mechanical treatment), testing con- ditions (temperature, time, and stress), and the complete composition of the steel (accompanying alloying elements, impurities, etc.). One ever-appear ing variable, hardness or tensile strength at room temperature, may be eliminated by heat treating all of the alloys to a single hardness level. An attempt may be made to control the variable of primary quenched structure by oil or water quenching the test specimen. The control of such variables may not be possible in cases of widely varying compositions, but at least such deviations should be recognized. Material and Procedure The alloys, made as 30-lb ingots in an induction furnace, all had the same base composition of about 0.18 pct C, 0.85 pct Mn, and 0.48 pct Si. They were grouped as follows: Mo Group—Containing up to 5.2 pct Mo. W Group-Containing up to 6.0 pct W. V Group—Containing up to 3.3 pct V. Mo-V Group—Containing up to 2.7 pct Mo and up to 1.4 pct V. Mo-W Group—Containing up to 2.5 pct Mo and up to 2.5 pct W. The steels, listed in Table I, were forged to ¾ in. sq bars and the material for the high-temperature, rupture-test specimens was further swaged to %-in. round bars.

Jan 1, 1957

By V. C. Petersen

The titanium-rich end of the titanium-germanium system was investigated by x-ray and metallographic methods and verified by resistivity and dilatometer measurements. A constitution diagram is proposed. The titanium-rich portion of the phase diagram is characterized by eutectic and peritectic reactions. The eutectic composition is 19 percent germanium, and the eutectic temperature 1,360° C. The peritectic reaction occurs at 905° C. and 4 percent germanium. Germanium is soluble in alpha titanium to a maximum of 4 percent at 905° C. and in beta titanium to a maximum of 12.5 percent at 1,360° C. Both limits of solubility decrease with decreasing temperatures. Although substantial quantities of germanium are soluble in beta titanium, beta is not retained on quenching. The beta phase probably transforms to alpha by a martensitic reaction.

Jan 1, 1957

By Robert C. Gabler

Three filter cloth fabrics commonly used in drains for coal waste embankments were tested by the Bureau of Mines for clogging behavior and deterioration under simulated field conditions. The objective was to provide guidelines for the mining industry for the proper selection and use of filter cloths to assure safer embankments at mine waste disposal sites. The filter cloths were tested with three coal waste samples in stand-pipes used to simulate coal mine waste disposal environments. Two of the cloths showed a tendency to become clogged with fines from the wastes. One waste caused clogging by precipitating an iron-silicon compound on the test cloths. No apparent cloth deterioration resulted from exposures to the simulated coal waste environments. (The exposures ranged from 2 to 12 months.) In other tests, exposures to waters in the pH range of 2 to 12 and to reagents used in coal-preparation plants resulted in insignificant or no deterioration, as measured by tensile strength. However, long exposures to sunlight (ranging from 4.6 to 6 months) caused major deterioration in two of the cloths (86-and 98-pct losses in tensile strength) and slight deterioration in the third cloth (9-pct loss in strength).

Jan 1, 1984

By Carolina Passanante

Aços Inoxidáveis Supermartensíticos surgiram na indústria petroquímica como um material alternativo para confecção de dutos, devido principalmente ao sinergismo de suas propriedades mecânicas e de corrosão. Com esta nova demanda, tornou-se necessária a caracterização deste material em suas diversas propriedades, destacando-se neste trabalho o efeito da microestrutura na resistência à corrosão. Objetivou-se, portanto, o estudo da resistência à corrosão por pite de um aço inoxidável supermartensítico 13Cr-5Ni-2Mo-Nb em função da fração volumétrica de ferrita-delta (d) presente na microestrutura. A variação da ferrita-delta foi alcançada através de tratamentos de recozimento, a 1.050°C, durante diferentes tempos (de 0,5h a 48h). As amostras foram submetidas a ensaios de polarização potenciodinâmica em eletrólito contendo 3,5% NaCl, naturalmente aerado. Quantificou-se, ainda, a porcentagem de ferrita em cada uma das condições através de ataque eletrolítico com solução 20% NaOH. Os resultados obtidos evidenciaram a diminuição desta fase com o aumento do tempo de recozimento, chegando praticamente à sua eliminação com tratamento de 48h. Paralelamente, a resistência à corrosão por pite deste aço foi melhorada de modo proporcional à diminuição da fase ferrita, resultando em um aumento de aproximadamente 115 mV da pior para a melhor condição, comprovando que, de fato, a presença de ferrita-delta prejudica as propriedades de resistência à corrosão localizada.

Aug 7, 2018

By Ted C. Briggs

A removable-jacket distortion apparatus was constructed and used to measure distortion coefficients for two high-pressure vessels. The measured distortion coefficients were used to compute distortion coefficients for volumes VI and (V1+V2) of a 1,000-atmosphere Burnett compressibility apparatus for the temperature range 0° to 75° C. Young?s modulus for Armco 17-4 PH stainless steel, heat treated to condition H1150-M, was computed from experimentally determined distortion coefficients. A 10-to 14-percent correction to the values obtained for Young&apos;s modulus may be required because pressure vessel end effects were neglected. The distortion coefficients of the compressibility apparatus are believed to be accurate to about 1 percent.

Jan 1, 1970

By Qiu Rongqing, Huang Kongxuan

This paper summarizes the results of treating arsenic­bearing refractory gold concentrates from six gold Mines of Chi­na by using bioleaching method and discusses the conditions of bioleaching processes. Results indicate that Thiobacillus fer­rooxidans T-3 Strain can intensely oxidize arsenopyrite, how­ever oxidation rate and degree differe considerably for different. During initial inoculation of 5 X 106 cell/ml. FeH contration generaly 4 -8 g/1. Sample size > 80 % - 3 20 mesh and pulp density 10 % ( w /v) and leaching time ,1 -- G clays, arsenic re­moval rate reached more than 80 % , Fe extraction ,10 - GO% desulfurization rate 30-45% after bacterial oxidation of 4-G days.

Jan 1, 1992

By G. R. Hopkins

[Apparent progress in fuel economy at petroleum refineries, as measured by the average amount of .seat units required to refine a barrel of crude oil, received a set-back in 1935, when the average rose to 562,00 B. t. u., compared with 562,000 B.t.u. in 1937 (see fig. l). The primary factor in the rise in average heat requirement&apos;s per barrel of crude oil refined in 1938 wan the decline in total runs to Invariably the average requirement increases when crude ins to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries arc masked by the degree to which the capacity is utilized. Additional crude runs give lower average e heat requirements in two ways - first, because they are mane with the c expenditure of comparatively small amounts of auxiliary heat, and, second, because the additional runs generally represent simple topping operations. In 1938 crude runs, to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938 .]

Jan 1, 1939

By B. Rezai

Impeller speed and air flow rate are two influence parameters on coarse particles flotation and collision and attachment angles. So, in this research recovery of quartz particles at four diameter classes carried out and collision and attachment angles investigated. It is found that maximum flotation response was observed at Impeller speed of 1100 rpm and 15 L/h air flow rate. For either more quiescent (Impeller speed<1100 rpm) or more turbulent conditions, flotation recovery decreased steadily. Furthermore, amount of attachment probabilities is calculated using suitable equation. According to this study, with decreasing particle size, air flow rate and impeller speed, probability of attachment increased and with increasing contact angle, probability of attachment increased. For various air flow rates, impeller speed and particle size, collision angle has been calculated. Maximum collision angle obtained at with 15 L/h air flow rate, particle size of 256 µm and impeller speed of 700 rpm and minimum collision angle obtained at with 45 L/h air flow rate, particle size of 545µm and impeller speed of 1300 rpm. In this study, maximum attachment angle, , was around 75 L/h air flow rate, particle size of 256 µm, contact angle of and impeller speed of 1300 rpm and minimum attachment angle was with 15 L/h air flow rate, particle size of 545 µm, contact angle of and impeller speed of 1300 rpm. ?82.72 ?64 cr??33.39 ?90 ?13.0 ?60

Jan 1, 2014

By J. D. Cooner

Since my working life of 32 yr has been spent in and about the anthracite mines of the Hudson Coal Co., and the previous 4 yr in a college school of mines, I can write best about the safety program of a coal mining company. However, most of the suggestions, statements and practices mentioned herein are applicable to the members of a safety organization and program of almost any industry. It is realized that industrial officials actually interested in real safety work are fully acquainted with the requirements of a practical safety program. Therefore, for such persons there may be nothing new in this paper. The Hudson Coal Co. of Scranton, Pa., employs 7000 men and produces 5,000,000 tons of anthracite annually at nine collieries scattered for a distance of 40 miles throughout the Lackawanna and Wyoming valleys of northeastern Pennsylvania. For the past 17 yr of the above mentioned 32, I have been engaged in safety work as a safety inspector, assistant mine superintendent, and at present the safety engineer. I have also had the privilege of visiting coal and metal mines in other parts of the United States and Canada. We Americans are the most careless people in the world. If any one doubts this statement why are 100,000 of our people killed accidentally annually? Or why during the almost four years we were engaged in World War II were more of our people killed accidentally at home than were killed in our army, navy, marine corps, coast guard, and other services during the same period? We are careless everywhere— in our homes, on the highway, at work and at play. The purpose of this paper is to outline the requisites of a safety department and its program to stop the accidents occurring to employees at work in mines or industrial plants. The first requisite for a safety program is that the management must be convinced of the need and value of a real safety program. By "management" is meant each department head from the president down. Otherwise a good safety department with a good safety program will not succeed because it will not have the proper personnel and equipment to work with, its rules and regulations will not be enforced, and the members of the safety department will be belittled in the eyes of most of the workmen and supervisors. Next, a safety engineer and his inspectors should have worked in the production end of the mines as workmen and also in an official capacity. They are then in a position to have practical and first hand knowledge of the accident hazards of the industry, how to prevent them, and in general the problems of both the workmen and officials. Some men are appointed as safety inspectors when they are physically unable to carry on as mine officials. Such men may know the safety end of the industry and even be safety-conscious, but if they are physically unable to be mine officials they are also physically unable to be safety inspectors, as a safety inspector in our mines must walk from 2 to 4 miles on each daily inspection and visit each working

Jan 1, 1949

By A. R. Denison

To those who are unfamiliar with the nomenclature in common use among operators in the Mid-Continent, the Permian Basin is a term to cover several widely separated productive areas. It includes what is designated in trade journals as the Panhandle fields, the West Texas fields and Southeastern New Mexico fields. It is bounded roughly on the east by the 100th parallel, on the west by the 104th parallel, 011 thr south by the Rio Grande River and various mountain ranges and on the north by the north line of the Texas Panhandle. The name is derived from the location of these three widely scattered areas which are all in a broad geosyncline which is chiefly filled with sediments of Perrliian age. The oil fields as now known and the approximate limits of the Permian Basin are shown in Fig. 1. The major part of the production in these areas comes from liniestonc or dolomite of Permian age. Some granite wash and sandstone production has been developed but ordinarily does not yield as large initial production as the limestone or dolorliite. Introduction During 1926, Texas, exclusive of the Gulf Coast, produced 12G1SS-1,-952 bbl. of oil,&apos; of which 40,727,877 bbl., or 32 per cent., was produccd in the West Texas Permian Basin. During 1927 the same area in Texas produced 167,176,000 bbl. %f oil, of which 89,779,000 bbL13 or 52 per cent., was produced in the West Texas Permian Basin. The increase in the total production of Texas is about equivalent to the increase in production in the Permian Basin. Since production in the Panliandle District declined during the entire year, the increase of production in the West Texas Permian Basin, and also the increase in Texas, is due to the enormous increase from the West Texas fields. Daily average pl-oduction in the West Texas fields increased from 68,211 bbl. on ,Jan. 8 to

Jan 1, 1928