Search Documents

By C. B. Dudley

In October, 1878, and again in February, 1881, I had the honor to make public, through the medium of the American Institute of Mining Engineers, the results of an extended study of steel rails which had been in service, and which mere taken for the purpose from the tracks of the Pennsylvania Railroad Company. These studies appeared in three papers. In the first of these papers the question. what kind of steel is least liable to fracture or disintegration in the track, was the principal one considered. In the second paper the question discussed was, does the power of steel to resist wear increase with the hardness ? In the third paper the relation between wear and the chemical and physical properties of the metal was the principal point considered. The general results arrived at, or the cooclusions reached, were, as follows: 1. That a mild steel is less liable to fracture, and if properly made, less liable to crushing or disintegration in the track than a harder steel. 2. That the wearing-power of steel in rails not only does not increase as hardness increases, but, on the contrary, diminishes; or, in other words, that a mild steel gives less loss of metal under the same service than a hard steel. These conclusions may be briefly stated in a single sentence—namely, in rails mild steel is not only less liable to fracture and disintegration in the track, but it also gives longer life, or wears more slowly under the same traffic; than harder steel. It is perhaps hardly necessary to add that by mild steel is meant steel

Jan 1, 1891

INTRODUCTION Data available on prophyry copper occurrences in the Andean, Caribbean, Appalachian, and Cordilleran orogens may be categorized in a manner to suggest a hypothetical evolution for deposits that occur in the western hemisphere. A classification of de- posits is also suggested. A classification dependent on internal structure of a porphyry copper deposit would lead to two broad categories, breccia pipe and stockwork models. A classification of this type is examined herein but it is not universally accepted in the literature. Modeling based on igneous petrography as well as metasomatism attendant with the sulfide mineralization is more widely accepted by economic geologists whose evaluation of porphyry systems is influenced by the presence or absence of a phyllic zone. Lowell and Guilbert model deposits ordinarily include a phyllic zone, whereas those of the diorite model do not. Position of the phyllic zone in the alteration sequence is a significant ore guide. Should the phyllic zone be absent, dependence on alteration zoning to identify metallization is weakened. Presence or absence of the phyllic zone therefore is a significant parameter in the economic evaluation of a porphyry copper deposit (Hollister. et al., 1975). The Lowell and Guilbert (1970) model commonly includes a phyllic zone in quartz- bearing rocks. Parameters of both calc-alkalic and the quartz monzonite models mentioned elsewhere in this volume are sufficiently close to the Lowell and Guilbert (1970) model that it should be expanded to encompass them. The diorite model remains separate and distinct because deposits of this type are characterized by an absence of quartz in the pluton, commonly highly gold: copper ratios, low molybdenum content, and regular absence of sericite in the alteration zones. Therefore, for the benefit of those

Jan 1, 1978

By M. Tsesarsky, M. Hazan, E. Gal

"Rock masses comprised of stiff inclusions in softer matrix are common in various geological environments. The heterogeneity and multi-scale nature of these materials make the evaluation of their mechanical properties a challenging task, which cannot be accomplished using conventional laboratory tests and composite mixture rules. We employ the homogenization method to estimate the mechanical properties of geological materials with inclusions. The homogenization method solves the equations of elasticity on the material (microscopic) scale for a unit cell subjected to unit strains under periodic boundary condition. The micro-scale elasticity equations are solved using the Finite Elements Method, and are in turn used to obtain the structure scale (macroscopic) material matrix.In this research, Finite Element models for unit cells with spherical and ellipsoidal inclusions were developed. Using the unit cells, a parametric study of the geometrical and statistical microscopic properties of the material composites was performed. The following parameters were studied: volumetric ratio, Young’s modulus ratio, size-distribution of inclusion and inclination angle of inclusions. The main purpose of the parametric study was to study the deviation from isotropy as a function of the aforementioned parameters.It was found that for volumetric ratio of 5%-40%, the deviation from isotropy increases, as the volumetric ratio of inclusions increases. For spherical inclusions, most of the cases studied exhibit quasiisotropic behaviour; whereas ellipsoidal inclusions exhibit considerable deviation from isotropy. The inclination of the ellipsoidal inclusions enlarges the deviation from isotropy (9% at random orientation and 26% at 0°)."

Jan 1, 2015

By R Araya, G Harbort, D R. Seaman, L Huynh, P D. Munro

In today’s operating environment many conventional cleaner circuits struggle to produce final grade concentrate with acceptable levels of non-sulfide gangue and/or penalty elements. This is primarily due to poor selectivity and the entrainment of gangue, and is further exacerbated by the processing of lower grade ores with more complex mineralogy that require finer grinding for liberation. In new concentrators, the standard approach to cleaner circuit design is to define the number of stages of mechanical cells required to achieve the desired concentrate grade. Residence time is the primary factor to size cells and to determine the number of cells required to attain target recovery. While it is required for recovery, a bank of mechanical cells is not the ideal solution to maximise concentrate grade. Relatively coarse bubble size means slow flotation of fines, requiring long residence times. The combination of long residence times and no froth washing means higher entrainment as the pulp becomes more barren and froth stability decreases down a bank.In recent years, the Jameson Cell technology has been retrofitted into a number of concentrators around the world to solve both cleaner circuit capacity and concentrate grade issues. Jameson Cells have been installed at the head of conventional cleaner circuits to produce final grade concentrate in a single step of flotation using a single cell (referred to here as ‘cleaner scalping’ duty). The experience gained from these installations has provided the platform for the design of improved and simpler cleaner circuits that will perform better and be more robust to operate. This paper analyses traditional cleaner circuit designs and explains the philosophy behind new hybrid cleaner circuits, which use Jameson Cells to produce final concentrate and mechanical cells for a ‘cleaner scavenger’ duty. The advantages of the new cleaner circuit design are demonstrated by a case study from an operating plant. Engineering studies show that the better metallurgical performance can be achieved with less equipment than conventional cleaning designs, reducing capital cost, operating cost, and with more than 30 per cent energy savings.Finally, the paper describes simple modifications to the standard laboratory flotation test procedures which accurately simulate this new cleaner circuit using routine equipment.CITATION:Huynh, L, Araya, R, Seaman, D R, Harbort, G and Munro, P D, 2014. Improved cleaner circuit design for better performance using the Jameson Cell, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 141–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Ross Gallinger

In 1997 a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded (i) that Canadian industry and NRCan should fund a small secretariat in Ottawa to support technology transfer in Canada and (ii) that it was important for industry to continue the momentum of MEND on an international scale. The need for INAP (International Network for Acid Prevention) was strongly endorsed by company, university, consultant and government experts from Australia, Canada and the U.S. who were convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP's members to promote the dissemination of successful practices, the identification of knowledge gaps and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry based initiative to globally coordinate research and development in the management of sulfide mine waste. Significant improvements in the management of sulfidic mine materials through knowledge sharing, research and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP.

May 1, 2002

By R. T. Mishler

I wish to express my keen appreciation of the article on the above subject by Coe and C1evenger.l It has been doubly interesting to me, for the reason that the experience recorded and the principles evolved practically parallel the results of similar investigations made by myself and others at The Lucky Tiger Mine, El Tigre, Sonora, Mex. An outline of the work at El Tigre may aid in confirming the principles expressed by Coe and Clevenger. El Tigre has the unenviable distinction of possessing a slime with a much lower settling rate than any recorded in the article discussed. Under most favorable conditions the settling rate is about one-third that reported for the Liberty Bell mill, and one-tenth that reported for the Nipissing, Golden Cycle, and Presidio mills. This slow settling characteristic of Tigre ore has necessitated careful investigation of settling phenomena throughout the various evolutions of the plant. Previous Settling Investigation at Tigre During construction work at the mill, the metallurgical engineer in charge, D. L. H. Forbes, ran a series of experiments on settling. His tests proved that deep settling tanks were not ordinarily necessary. The use of tanks 2 or 3 ft. in depth was suggested.2 Later experiments demonstrated that the following principles of settling applied to Tigre pulp.3 1. In settling dilute pulp, settling rates are independent of pulp depth. 2. In settling thick pulp, settling rates are approximately proportional to pulp depth.4

Jan 1, 1918

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan's total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan's total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By Carmen M. Neculita

Optimizing the long-term efficiency of passive systems for the treatment of highly contaminated acid mine drainage (AMD) is still a challenging issue. The optimization lies, among others, on improving the understanding and quantification of metal removal mechanisms in order to predict and enhance the stability of neo-formed minerals in secondary phases. Sorption, and precipitation as oxides-hydroxides, carbonates and bio-sulfides are likely the most important metal removal mechanisms involved in passive biotreatment of both slightly and highly contaminated AMD. In the same time, the preferred mechanism is precipitation of metal sulfides that are more stable and less pH dependent than carbonates and oxides-hydroxides. However, results of relatively recent research studies performed at laboratory scale showed that sulfides accounted only for up to 15% of total metals removed in passive bioreactors treating highly contaminated AMD dominated by iron (around 500 mg/L). Several approaches were used in the aforementioned studies to understand and quantify metal removal mechanisms in spent reactive mixtures collected from long-term (12-15 months) operating column bioreactors. These included: thermodynamic equilibrium modeling and various chemical extractions and mineralogical analyses (such as single and sequential extractions, acid volatile sulfides-simultaneously extracted metals determination, scanning electron microscopy, X-ray diffraction, and thermo-gravimetric analysis). The large proportion of metals (85%) removed by sorption and precipitation as oxides-hydroxides and carbonates suggests a relatively high mobility of the neoformed minerals, especially in low pH conditions. However, no data is available on the long-term stability of spent reactive mixtures and, on the implications for the sustainable management of this type of solid waste. Lately there is almost a consensus that the efficiency of highly contaminated AMD treatment is warranted by the use of multi-step passive systems, including both chemical and biological units, installed sequentially. However, very few well-documented studies are available on the design, construction, operation and long-term efficiency of these multi-step systems. A leading example is the tri-unit passive system installed on the abandoned Lorraine mine site (Québec) to treat a highly contaminated AMD dominated by iron (about 2,500 mg/L). This tri-step system (160 m3), consisting in two bioreactors separated by a unit filled with wood ashes, achieves to date a satisfactory removal of iron (up to 99%). Moreover, based on the data collected during laboratory testing, iron was mainly removed in the wood ashes unit (from around 3,200 mg/L to 10 mg/L) by precipitation of oxides-hydroxides as predominant mechanism and only partially by sorption. However, no data is available on the actual metal removal mechanisms in the field. Overall, theses multi-step systems are more complex and their long-term performance is even less predictable than the single unit systems. This paper presents the current knowledge and the research needs on metal removal mechanisms in passive bioreactors and multi-step systems for the long-term treatment of highly contaminated AMD. KEYWORDS

Aug 1, 2013

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957

By Klinefelter G

The United States Steel Mining Co., Inc. recently experienced a major mine fire at the Cumberland Mine. This mine is located in Greene County, Pennsylvania, U.S.A. and is mining a high volatile bituminous coal seam (Pittsburgh Seam). The mine fire was success- fully controlled and extinguished without loss of life or serious injury to any miner or mine rescue personnel and finally reopened within 40 days of its inception.

Jan 1, 1988

By Yannick Bleuzen, Manuel Joao, Frederic Monath, Miguel Quaresma

The N1 Porto tunnel project is a 650m segment of large-scale civil engineering plan to improve traffic flow between Porto’s downtown district, the Santo Antonio hospital district and the highway access. The tunnel is being excavated into a massive “Granito do Porto” granite structure, 4 – 20m below a highly urbanized environment of Porto, Portugal. The project was originally started in 2000 and was stopped due to the inability to mechanically excavate the granite rock. The city of Porto engineers then turned to traditional drilling and blasting techniques. The use of pyrotechnical delay detonators did not easily comply with the specified environmental and safety requirements concerning blast charging, firing and vibration control resulting in the process taking far too much time. The introduction of digital blasting was proposed to overcome these concerns.

Jan 1, 2005

By Albert W. Giles

The splitting of the coal by partings is a familiar feature of many coal beds. The partings are normally argillaceous, more rarely sandy or calcareous. The material is usually fine-grained, less frequently coarse-grained to conglomeratic. Many partings are wedge-shaped, others are lenticular, and in some coal beds thin partings but one or two inches thick persist as thin sheets throughout areas of regional extent. The origin of the partings differs, and in some cases is obscure and uncertain. Origin of Thick Partings Wedge-shaped Partings Wedge-shaped partings are normally of indefinite linear extent but of short transverse section. They are developed adjacent to the borders of the original peat-forming swamp or around islands formed within the swamp, hence their presence is indicative of the approximate limit of the coal bed or of an interruption in the continuity of the coal bed. Following deposition of the parting gradual reestablishment of swamp conditions is followed by burial of the parting with accumulating peat. Partings developed adjacent to the borders of swamps normally thicken toward the periphery of the swamp and represent either detrital materials carried in from adjacent land areas during floods or materials carried in by advancing waves and currents after a barrier confining the swamp had been breached by the waves. Partings formed in the manner first mentioned should become coarser and more arenaceous toward the source of supply of the detrital materials, and the overlying and underlying coal should gradually grade into carbonaceous shale as the margin of the original swamp is approached. Partings formed by advance of waves across a barrier should be largely or entirely arenaceous, thin wedges of short longitudinal section, possibly with fossils of marine or brackish affinity. The subjacent coal normally should "pinch out" against the barrier, and the overlying coal continue to the barrier, or even extend across it, depending on the geographic conditions established following the breaching of the original barrier. Islands may be formed in swamps in a number of ways. They may represent local uplift of the swamp floor during earthquakes, or

Jan 1, 1934

By Wallace W. Roepke, Jon I. Voltz

"The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60° and 90° (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate. INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969, with revisions in 1977, was enacted to ensure more healthful and safer working conditions for miners. The Bureau of Mines coal-cutting research facility at Twin Cities (MN) is examining fundamental aspects of the cutting system, including generation of primary dust causing pneumoconiosis in miners and ignition of methane by the frictional impact of cutting bits used on continuous mining machines (CMM's). The cutting system is defined as the cutter-mineral interface area with all its variables, e.g., forces, speed, cutter geometry, bit-mounting geometry, and wear. It has become obvious over the past several years that the cutting system directly affects the economics and design of the ""total system,"" which is defined as all areas of the operation, from the mine face to the preparation plant, which support the mineral recovery by cutting tools to obtain a salable product."

Jan 1, 1983

By A. I. Gorshkov, Y. A. Bogdanov, O. Y. Bogdanova

Abstract - Detailed crystal-chemical study of iron and manganese oxides and some other minerals from low-temperature hydrothermal deposits in a newly discovered inactive mound in the TAG hydrothermal field were used to determine the precipitation sequence of mineral phases during lowtemperature processes and their post-sedimentary transformations. Particles of primary sedimentary X-ray amorphous proto-ferrihydrite with high silica content were replaced in situ by nontronite, ferrihydrite, or goethite during alteration. Ferrihydrite is the only proto-hematite phase. The transformation of the iron minerals, related to change in the physicochemical environment, is an important characteristic of low-temperature hydrothermal processes. The occurrence of hydrogenetic Fe vernadite and Mn feroxyhyte in the uppermost part of low-temperature deposits and bottom sediments near the base of the mound is evidence for cessation of low-temperature hydrothermal processes. Among the investigated mineral phases, goethite, nontronite, and hematite are stable in reduced sediments only.

Jan 1, 1999

By John M. Karpinski, David S. Cahn

A new device based on a constant rate of loading has been developed for the compression testing of green and dry pellets. This device has a lower test variation for green pellets than the existing constant deformation rate tester. While the test variations for dry pellets are similar for both types of machine, the new tester is sensitive enough to measure dry pellet deformations of 15 µ in. for cyclic loading studies. In the study discussed here, the compressive load at which a pellet breaks proved to be a normally distributed random variable, and the load-deformation relationship was found to be linear for dry pellets but not for green pellets. The paper emphasizes the need for a standardized test procedure throughout the industry. For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate

Jan 1, 1969

By P. R. Brito-Parada, G. Bhutani

"The physical processes occurring in flotation columns are very complex as they take place at different scales over a range of sizes and multiple phases. Column design and optimum operating parameters are usually obtained from empirical studies and although progress has been made on its numerical modelling, most column models rely on simplifications that do not fully capture the hydrodynamics. In particular, Computational Fluid Dynamics (CFD) models of the pulp phase in flotation usually assume the bubble population to be monodispersed. While this assumption may be reasonable in some situations, the polydispersed nature of the gas phase can have a significant impact on the predicted flotation rates.Techniques to model size distribution do exist in the literature and have been rigorously analysed in the past two decades for bubble columns, which are very similar to flotation columns from a hydrodynamics point of view. In fact, available CFD models of flotation columns are an extension of bubble column models, sometimes including additional equations for solids treated as passive scalars. This work focuses on the development of an efficient CFD model for flotation columns. The bubble size distribution in the column has been modelled using the Population Balance Equation (PBE), which is solved using the Direct Quadrature Method of Moments (DQMOM). Coupled with the PBE, the multiphase flow equations in the column have been modelled using the standard Eulerian–Eulerian approach. The solution of this coupled system has been made tractable in this work with the implementation of a highly parallelised adaptive-mesh finite element method. This powerful framework has been implemented in the open source CFD code Fluidity and it allows the carrying out of detailed simulations of flotation columns in 2D and 3D, with important implications for industrial column evaluation and design."

Jan 1, 2016

Longwalling has reached a high standard both in Germany and Australia and most improvements should be expected in planning, monitoring and control. Double drum shearer have electric drives to 1000 kW and automatic height control is under development. Conveyor pans to 40mm thickness and chains to 2300 kN breaking load are in use with controls for pretension and load compensation under test.Trends in support are towards two leg shields with loads to 3850 kN per leg and electrohydraulic controls. Expert systems have been devised for planning and diagnosis tasks. With increases in technical standards, staff qualification standards at rising too, drawing attention to training requirements for modem personnel.

Jan 1, 1991