Search Documents

By C. E. Jr. Reistle

ALL crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms.

Jan 1, 1927

By Nicholas J. Grant, Yoichi Ishida, Arthur W. Mullendore

An inert particle -marker technique was developed to provide a direct measurement of grain boundary sliding during creep in tile interior of aluminum specimens. Groin boundary sliding in the interior as measured by this technique was found to be nearly the same or slightly lower than that measured on the surface. These data disagree with those obtained by the grain-counting technique developed by W. A. Rachinger. In tests where both techniques were used, the grain-counting technique gave large and variable values of grain boundary sliding. It is shown that the grain-counting technique gines erroneozcs results because of a preferred direction of grain growth during creep. A question which has long plagued those who study grain boundary creep is whether or not surface measurements yield a true representation of the deformation in the interior of a specimen. The first attempt to measure grain boundary sliding in the interior of a creep specimen was made by Rachinger.1 His technique is based on the measurement of average grain diameters, both parallel and perpendicular to the tension axis, followed by a calculation of the grain elongation from these measurements. The difference between total elongation, Et, and the calculated grain elongation, Eg, is considered to be the result of grain boundary sliding, Egb. Surprisingly large values of Egb/ Et (90 pct) came out of creep tests of pure aluminum at temperatures above 250°C (480°F), utilizing the Rachinger technique. This value is very much larger than the values of 8 to 15 pct measured by numerous investigators on the surface of a specimen. Values obtained on the surface by Rachinger, however, were consistent with those measured by the displacement of reference scratches. Chaudhuri and Grant2 repeated the Rachinger method for A1-10 pct Zn, and found the same large values of Egb/Et inside the specimen. However, from purely geometrical considerations, grain boundaries cannot slide without grain deformation; therefore, they questioned the validity of Rachinger's grain-counting method. Several authors2,3 have suggested that grain boundary migration during high-temperature deforma- tion may tend to restore the equiaxed grain shape in order to minimize interfacial energy. Rachinger4 tested this hypothesis and found that it did not hold. Grains elongated by rapid extension retained their elongated shape during a subsequent slow creep test. It appears that some other factor was responsible for the abnormally high values of .Egb/El. McLean and Gifkins5 made a survey of the effect of grain size on the ratio Egb/ Et, and proposed that the high values were the consequence of a small grain size. They failed to explain the low value of Egb/Et which Rachinger observed on the surface of the small grain size specimens, and suggested that the surface effect on the value of Egb/Et does not always occur. Many of the disagreements arising from Rachinger' s work stem from the fact that there was only one method of estimating grain boundary sliding in the interior of a specimen, and that method was of an indirect nature. If a marker line of some sort could be introduced inside of the specimen, one could make measurements just as clearly as on the surface. In the present investigation, the technique utilizes a layer of finely dispersed oxide particles inside the specimen introduced by hot press-bonding of two pieces of aluminum. Rachinger attempted a similar technique but with the oxide distribution he obtained there was so much interference with grain boundary motion that quantitative measurements were not attempted. MATERIALS AND EXPERIMENTAL PROCEDURE A) Materials Preparation. Two pure aluminum rods (impurity content in percent: Si, 0.002; Cu, 0.004; Fe, 0.002; Mg, 0.000: Zn, 0.000; V. 0.001) 1 in. diameter by 2 in. high were jacketed end to end in a 4-in.-diam cylinder of commercial-purity aluminum, 4 in, high, which had a l-in.-diam hole. The l-in.-diam mating surfaces of the two pure aluminum rods had been electropolished initially. This interface provided the oxide-film internal -marker plane after the hot press-bonding process, see Fig. 2. The composite was annealed for 1 hr at 900 F and hot upset more than 50 pct reduction in height in one step. The resulting slab was then rolled to 1/2 in. thickness; the pure aluminum test material was cut out and annealed at 900°F for 1 hr and cold cross-rolled to 1/8 in. thickness. The sheet was machined into specimens with a 1/8-in.-square cross section and a 1/2-in. gage length. The following heat treatment was given the specimens: Specimen 5A series: annealed at 1000°F for 5 min for grain-size control and then cooled to 700°F and held for 15 hr for stabilization.

Jan 1, 1965

By C. C. Henning

IN any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel constitutes a large volume of tonnage in daily use. There is a fairly prevalent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applications sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment, Some forging work and considerable heat treating, particularly carburizing, is performed on this grade. From an economic standpoint the most effective contribution of bessemer steel lies in its free machining qualities. It is by far the freest

Jan 1, 1935

By AIME AIME

AT the end of September, ' the metal-producing industries were almost prostrate, the production of fuels was largely curtailed, there was a fair degree of activity in general manufacturing, while retail trade was moderately good. Looking at industry on the whole, there was a large percentage of unemployment, the degree of which has increased, progressively, month by month since the beginning of 1921. There is the prospect of much destitution and misery this winter; yet while' in some, quarters, idle workers are already being fed from, commissaries; in other quarters profligacy; in "spending continues, unabated. Amid this confusion in conditions there is;' much that appears paradoxical, but in fact it is not so and indeed everything is running pretty true to form: Such activity in production as there is to be seen is mainly in textiles; - leather goods, foodstuffs, etc., i.e., consumption goods for immediate use. Even in hard times 105,000,000 people must buy a good deal of clothing and food. Besides this there is indispensable repair work and- maintenances. Thus, the good business of the year in white lead for painting. The chief uses for the metals, however, are in the production of capital goods, and except for occasional and special reasons nobody in his senses is capitalizing anything at present prices for labor. Hence several millions of men are idle. The impoverishment of Europe and the exhaustion of her credits adds to this by curtailing our export trade.

Jan 1, 1921

By J R. Leeming

Mining law has developed in Great Britain (GB) over centuries, mainly in response to lessons learned after disasters and other major incidents. This has led to a culture of preventing repeat accidents, rather than predicting and controlling unsafe acts or conditions.This paper explains how, initially in response to a government drive to reduce the burden on industry, the opportunity was taken to review and reform all 48 sets of GB mining-specific law into a single document. The philosophy adopted, the procedure followed and the significant changes that resulted are explained.CITATION:Leeming, J R, 2017. The complete renewal of Great Britain’s mining laws for the 21st century, in Proceedings Australian Mine Vent Conference 2017, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By R. Karl Zipf

Highwall mining is an important coal mining method. Upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mine Safety and Health Administration (MSHA) accident data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwail miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Trapped highwall miners present a safety hazard to workers during their recovery. Best practices to avoid trapped highwall miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system, Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

Jan 1, 2004

By Paul B. Crawford, Melvin B. Burton

A procedure is given which describes how the gelatin model may be-used to study the effect of mobility ratio on areas swept before and after breakthrough in fluid injection programs. Differences in mobility ratio are achieved through the proper selection of electrolytes for the invading and displaced fluids. The progress of the front is followed visually and photographed or traced onto plates (it desirrd positions before and after breakthrough. Example applications to standard flooding pattrrrls, vertically and horizontally fractured reservoirs and the in-situ combustion recovery process ore presentrtl. INTRODUCTION In water flooding, gas cycling and other fluid injection programs, the sweep efficiencies and swept areas after breakthrough are known to depend on the mobility ratio. Previous investigators have described the application of the X-ray technique, stepwise use of the poten-tiometric model and numerical procedures for studying these problems.1,3,4,6 Others have described the application of the electrolytic and gelatin models for studying sweep efficiencies at a mobility ratio near one.2,5,7,8,9 It is a purpose of this paper to describe a procedure for using the gelatin model to study swept areas at mobility ratios other than one. PROCEDURE The technique developed for gelatin model studies is composed of four phases: the construction of the model, the selection and preparation of electrolytes, the running procedure, and the recording of the swept areas. Each phase is discussed independently in order that the over-all procedure will not be confused. Construction of the Model Since some of the advantages of the gelatin model are its economy, and speed, it is desirable to have as small a model as is possihle without creating error through the inability to follow visually the progress of the colored front. For this work, it was found that a distance of 4 to 6 cm between salt bridges is convenient to use. Since the size is relatively small, it follows that the gelatin layer must be thin. For this study, 1/8 in. was used as the gelatin thickness in each case. The model was constructed on a flat 1/2-in. plastic (Lucite) base with boundaries constructed from 1/8-in. plastic strips. The well pattern to be studied was outlined with the 1/8-in. plastic strips on the base with narrow apertures (- - 2 mm) in the boundary to represent the wells. Behind each well opening, a rectangular area of some 8 to 12 sq cm was outlined by additional plastic strips. The plastic strips were fastened to the base by any suitable non-conducting cement so that the boundary system was liquid tight. The electrodes were constructed from sheet copper in a fashion that would allow easy removal. In this work, it was found that by simply forming a large U-shaped clip from a strip of the copper that would slip over the boundary was satisfactory and easily removed. The electrodes should be as wide as one of the sides of the rectangular area behind the well opening. If a fractured pattern is studied, fractures inside the well pattern may be represented by strips of copper of the desired shape mounted in some easily removable fashion. The reason that apertures (or salt bridges) were used for wells instead of metallic electrodes is that the plating of the electroactive ion at the cathode and the introduction of an electroactive ion at the anode has a detrimental effect on the swept area outline if these operations \rere permitted to be carried on within the well pattern itself. The anode may be used within the well pattern

Jan 1, 1957

By H. E. N. Stone, B. L. Daniell

This paper examines the cracking behavior on chemical reduction of three types of ore/oxide briquette mixtures. The complex sintering/hardening atmosphere was replaced by 100% oxygen and the blast furnace atmosphere by a 5/95 hydrogedsteam mixture which was used isothermally at 700°C for a constant, arbitrary time. Cracking has been assessed by measurement of reduction expansion or increase in specimen diameter as a result of chemical reduction and a subjective index based on appearance and friability. Oxidized briquettes of iron ore concentrate crack on reduction'-3 in a manner which parallels the degradation of sinter in the Linder test. In the present work, the cracking behavior on chemical reduction of three types of ore/oxide briquette mixture has been studied. Firstly, LD converter fume with additions of silica; secondly, Oxfordshire ore with ferric oxide; thirdly, ferric oxide with separate additions of silica, alumina and lime. Motivation for the first-mentioned experiments lay in the improvement of the fume as furnace feed; for the second, in assessing the tolerance of a finely divided ferric oxide as a base for low melting point additions. The third series provided additional information. In this work, the complex sintering/hardening atmosphere is replaced by 100% oxygen and the blast furnace atmosphere is replaced by a 5/95 hydrogen/ steam mixture used isothermally at 700°C for a constant arbitrary time. The particular reduction conditions were known from previous experience3 to be capable of disclosing any tendency to cracking. Cracking has been assessed by measurement of reduction expansion (i.e., increases in specimen diameter as a result of chemical reduction) and a subjective index based on appearance and friability. Generally

Jan 1, 1970

By D. A. Stout

Mr. Chairman and Members of the Rocky Mountain Coal Mining Institute: Your Secretary has asked me to write upon a subject' which is a most interesting one, and which has a very wide scope. In view of the great need for further decreasing costs at its coal mines, the Colorado Fuel and Iron Company began early in 1924 to experiment with methods of mining which had not previously been. tried out at its mines, and which were selected because of the greater possibilities for the concentration of the work, better grouping of workmen, and increased tonnage per workman, with a resultant increased efficiency, better supervision, and lowered costs. Because of the great competition of the day, means and methods must be provided by which fewer mines can be made to produce larger tonnages and at a lower cost. Western physical conditions are such as to make our problems far more complicated and not so easy of solution as compared to many of the eastern fields where conditions are more favorable for the operation of the mines. The dry condition of our Western mines on account of a relatively low humidity, and with additional gaseous conditions, makes the problem still more difficult to solve. A study of new methods was necessary before adoption, and this was particularly true of the method of extracting the coal. Where mechanical means are used, particularly in the coking coal mines of this state, due consideration must be given to the type, and machines or conveyors should not be installed solely on the basis of their performance elsewhere, without the knowledge of local influencing factors. In trying out the newer methods of extraction at our mines, very careful consideration has been given to the question of safety and the adoption of any new methods must provide adequate means of protection to employes, and be approved by' the State Coal Mine Inspector. In any large industry there are a few outstanding operating costs, and usually the leading ones in their order are labor cost, material cost, and power cost. The things which we, hope to accomplish: 1. Reduce labor costs. 2. Reduce material costs. 3. Reduce power costs by the con 4. Reduce the amount of powder used per ton of coal produced. 5. Increase the lump percentage (particularly at the domestic mines). 6. Reduce accidents and annual compensation payment. 7. Reduce haulage costs. 8. Reduce cost for track work. 9. Reduce cost for timber and timbering, and increase the recovery of timber at a considerable additional saving. 10. Reduce the brushing costs. 11. Reduce the amount of rock hauled to the outside. 12. Reduce the cost for drainage. 13. Reduce the cost for ventilating. 14. Reduce cost of inspection and supervision. 15. Reduce the cost for shot firing. 16. Reduction of number of working places. 17. Grouping of men with increased sociability. 18. Increased tonnage per man. 19. Reduction in total number men employed. In the consideration of the methods used and now working successfully, there were three points which were considered outstanding, to make them wholly successful: ventilation, roof control, and transportation. For making the experiments, those mines were selected where conditions

Jan 1, 1925

Outokumpu Technology’s HSC Chemistry process calculation software enables the user to simulate an entire chemical or physical process. The HSC Chemistry 6.0 contains 21 calculation modules and 11 databases for reaction, equilibrium, heat balance, heat transfer, petrological and simulation applications. Most of the calculation modules automatically utilize the same extensive thermochemical database which contains enthalpy (H), entropy (S) and heat capacity (C) data. This database has been expanded to include more than 20,000 species.

Jan 1, 2007

By W. Guiye, L. Chongjun, L. Huinan, Z. Yangge, H. Long

The current application of copper-molybdenum (Cu-Mo) separation inhibitors is often associated with large dosage, high toxicity, environmental pollution problems. In order to solve these problems, a light sensitive Cu-Mo separation inhibitor LS（light sensitive inhibitor，abbreviated to LS） was developed. In this paper, inhibitory performance, photodegradation rule, and acting mechanism of LS were studied. The subsequent test results showed that, compared with traditional inhibitors, LS has shown comparative advantages, with lower dosage and good inhibiting effect. A series of flotation tests with LS as inhibitor were conducted on a Cu-Mo concentrate. A locked-cycle test showed that a molybdenum concentrate containing Mo 49.88% and Cu 0.6%, with 93.23% molybdenum recovery and a copper concentrate containing Cu 29.92%, with 99.99% copper recovery can be obtained. The photodegradation performance of the reagent was investigated under 365 nm, 254 nm and sunlight irradiation. The degradation of the reagents could be completely achieved by irradiation of three wavelengths of light. However, with the different wavelength of irradiation light, the degradation rate is different, the time required to reach 50% degradation rate being 3 h (254nm), 4 h (solar light) and 6 h (365nm) respectively. The inhibition mechanism on chalcopyrite was studied. FTIR study showed that LS could be adsorbed on the surface of chalcopyrite by chemical adsorption, which could enhance the hydrophilicity of chalcopyrite. Ultraviolet adsorption tests indicated that the adsorption capacity of LS on chalcopyrite surface was greatly affected by pulp pH value, and the proper pH value was 5-9. Keywords: Copper-molybdenum separation, Inhibitor, Light-sensitive, Photodegradation, Mechanism.

Jan 1, 2020

By Thor Pedersen

Elkem's technologies for the processing of waste materials, dusts, sludges and other residues, are based on the use of their Multi-Purpose Furnace as the primary processing component. The Multi-Purpose Furnace? is an electric slag resistance reduction furnace equipped with a hot media, Modular Freeze Lining and Elkem's proprietary, air tight electrode seals. The oil cooled? freeze lining allows specific heat fluxes 2 to 3 times higher than furnaces lined with conventional refractory. Reduction activities taking place within the furnace are free from the reoxidation potential of infiltrated air as Elkem's electrode seals are positively gas tight. Small quantities of highly concentrated off gas of controlled composition are produced to suit the requirements of downstream processing. The high electrical thermal efficiency achieved by generating heat within the slag itself, combined with the ability to operate at high melting rates and intense power density, makes the Multi-Purpose Furnace 9 an unique implement for the design of furnace products. These characteristics are utilized in the processing example cited, "Elkem's EAF Dust Processing Technology", which combines two proven technologies in an economically feasible system for the recovery of contained metal values from K061 wastes at the same time producing a disposable slag product. The portion of the example dealing with the condensation of zinc was prepared with the assistance of Imperial Smelting Processes, Limited of Bristol, England with whom Elkem has a non- exclusive license.

Jan 1, 1990

The session opened at 9:00 a.m. Presiding- Herman E. Knight, Vice President, The Pittsburg & Midway Coal Mining Co. and Gulf Mineral Resources Co., Denver, Colorado. The first speaker was Dale A. Eastman, President, Eastman, Griggs & Associates, Salt Lake City, Utah. Subject-"Professional Staffing for Mining Operations." Mr. Eastman received his Business Degree from Shadran State College in 1971. He was Head Coach in basketball and football in Lyman, Wyoming, prior to joining Bectel. With Bectel five years in training, development and staffing. Was Director of Construction Administration for Southwest, United States, Bectel Power Division prior to entering the Executive Search Division. Currently President, Eastman, Griggs & Associates and also Vice President of E&B Investments and Managing General Partner Duffers Ltd. (See Index for printed text of Mr. Eastman's paper.) Mr. George J. Miller, Attorney, Dechert Price & Rhoads, Denver, Colorado, was the second speaker. Subject-"Rail Transportation After Staggers Act."

Jan 1, 1981

By J. B. Newkirk

ABOUT twenty-seven years ago W. bergl discovered that interesting detail could be seen in an X-ray diffraction spot made with a rock-salt crystal if the recording photographic film were held very close to the reflecting crystal. He also showed that much of this detail could be explained in terms of the deformation structure of the specimen. In the same year, 1931, Fox and parr2 reported that X-ray reflections from a quartz crystal were much more intense while the crystal was undergoing piezoelectric oscillation than when it was at rest. This observation was soon confirmed (and explained in terms of X-ray extinction) by Barrett3 in the United States and by Nishikawa et a1.,4 in Japan. During the next few years Barrett refined Berg's method for making X-ray diffraction micrographs and applied it to the study of metallic crystals. He reported this work in the 1945 annual lecture of the AIME.5 Since 1945 relatively little use has been made of the Berg-Barrett (B-B) method for making diffraction micrographs, though considerable interest in investigating subcrystal structures by other methods has developed. Some of these methods depend upon evaporation6 or chemical etching7 and, therefore, suffer from the occasional intrusion of subtle artifacts such as those recently reported by Hooker for leada and Welsh for aluminum.9 Other methods require the introduction of foreign elements which "decorate" the substructure in some way, thereby rendering it detectable by direct" or indirect1'. visual examination. Still others depend upon complex and often highly questionable analyses of X-ray diffraction line profiles. There have also been a number of related X-ray techniques, such as the Lambot,12 Schulz13 and Merlini and Guinier,14 which have proved to be quite useful for specific applications. Some of these methods give a picture of the substructure which is more or less directly related to the shape and the topography of the specimen. The Berg-Barrett method carries this desirable feature to the limit. Closely related to the B-B method are three photographic X-ray techniques recently described by Lang.15 These methods give beautiful pictures of the internal structure of crystals but are limited by the facts that the required apparatus is rather complex, exposure times are long, and the specimen crystals must be thin. An experimental appraisal which I have recently made of the original B-B method has shown that this simple technique is not only inexpensive and convenient, but can give more information than was apparently realized by its inventors. For example, first-order subgrains in iron-silicon crystals were clearly delineated and their relative orientation subject to description. Also defect structures could be seen within the subgrains and in some materials slip bands could be clearly seen with respect to the topography of the rest of the specimen. This much had already been described by Barrett. However, in the present study it was found that the actual sites of individual dislocations which emerge upon the crystal surface could be located. Furthermore, by a simple procedure, the direction (but not sign) of the dislocation Burgers' vector could be defined as well.

Jan 1, 1960

By M Sebbag, T Taimre

Barrick Gold Corporation is proceeding with development of the Buzwagi Mine in the Lake Victoria Greenstone Belt District of Tanzania. The Buzwagi orebody occurs in the Nzega Shear zone within the Greenstone Belt and is hosted in a K-Feldspar rich granite in contact with mafic volcanic. The orebody presents 2.6 M ounces in 41 Mt of reserves, at 2.0 g/t. Over the ten year mine life, total material movement will be 261 Mt. The feasibility study was completed in 2006 and presented several technical challenges. Two principle challenges are grade control and the impact of dilution on the economic viability of the project. The principle challenges for grade control will be quality control and quality assurance in the sampling of the massive coarse grained granite, which comprises 70 per cent of the deposit. The principle challenge with dilution will be with the selective mining of the narrower mineralised zones contained within the mafic volcanics. This paper will focus on the mine planning methodology which has been applied including selective mine unit (SMU) and dilution estimation, net smelter revenue (NSR) calculation and the effects of cut-off grades to the project economics and mine schedule.

Jan 1, 2007

By W. H. Eardley

IT IS increasingly evident that the excellence of blast-furnace operation to a great extent depends upon the preparation of the products fed into the furnace. The preparation of these products is carried on largely in the roasting and sintering departments. Prior to the building of flotation plants in Utah and other western states for the treatment of lead-zinc ores, the gravity concentrates received at the Midvale smelter amounted to about 4000 tons per month, containing 24 per cent. lead and 10 or 11 per cent. zinc. This product was about 20 mesh-that is, 45 per cent. of it would be plus 20 mesh and the balance minus 20 mesh. About 1000 tons of pyrite per month, containing 5 per cent. lead and 10 per cent. zinc, was also received. These products were sent to the multiple-hearth roasters for calcining, after which they were sent to the Dwight-Lloyd machines for sintering with other ores. The sintering charge passed over the machines but once. The first flotation products received consisted of a wet, sticky, muddy mass, containing a large amount of moisture, up to 19 or 20 per cent., and it was almost impossible to feed .them with any degree of regularity, if at all, through our standard feeders; but the amount of flotation product received during the first year or so was relatively small and it virtually lost its identity by being mixed with a large amount of jig and table concentrates. As the quantity of flotation products increased, more efficient filtering was accomplished and the moisture greatly reduced. FLOTATION PRODUCTS RECEIVED At the present time the Midvale plant receives about 4300 tons per month of flotation product running 60 per cent. lead and 4.5 per cent. zinc, 85 per cent. of which is minus 200 mesh and contains about 8 per cent. moisture; and 4000 tons per month of pyrite of similar fineness, running about 2 per cent. lead and 3.5 per cent. zinc, containing about 10 per cent. moisture. The lower moisture greatly reduces the difficulties of handling, making it possible to run a 100 per cent. flotation feed on a multiple-hearth furnace without serious mechanical troubles. The calcine, however, would contain-nodules and balls of unroasted concentrates, sulfur elimination

Jan 1, 1928

By Quian Liu

The problem of cross-hole explosive malfunctioning in rock blasting (including sympathetic detonation, desensitization and cut-offs) is a function of delay and spacing in a blast which should be designed to avoid such occurrences. On a delay-spacing chart, the phenomenon of explosive malfunctioning is explained by dividing the chart into different regions, while the shape and size of each region could vary from one explosive to the other. Over seventy blasts have been carried out at the CANMET Experimental Mine to identify the malfunctioning characteristics of specific emulsion, water-gel and dynamite explosives. In each experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1994

By Ted D. Maki, Joseph B. Taylor

INTRODUCTION FMC's Paradise Peak mine, located 13 Ian (8 miles) south of Gabbs, Nevada, became opera¬tional in April of 1986 (Figure 1). It was designed and built by Davy McKee, who was instrumental in equipment design and selection. It is the 7th largest gold deposit in the United States with defined reserves of 10.9 mt (12 million st) containing 34 million gms (1.1 million tr oz) of recoverable gold and 933 million gms (30 million tr oz) of recoverable silver. The mine extracts ore by the open-pit method, taking advantage of a 1.5:1 stripping ratio. The mill operates at a 3600 mt/day (4000 st/d) capacity. Crushing is done in three stages to achieve an ore size of minus 0.635 cm (0.25 inches). Grinding further reduces the ore to 85% minus 100 mesh. The ground ore is treated with cyanide in agitated leach tanks and then washed in the counter-current decantation (OCD) thickeners. Zinc is added to the clarified, deaerated pregnant solution to precipitate the precious metals. The precipitate is acid digested to eliminate excess zinc, filtered and retorted to drive off contained mercury. The retorted precipitate is then fluxed, melted and poured through cascade molds. Dore bars are cleaned for shipment and the slag is sent to an in-house slag treatment system. ELECTROSTATIC SEPARATION The dry electrostatic slag treatment system at Paradise Peak is the first installation of its kind. Electrostatic separation has been widely used in mineral processing since the early 1950's. A brief discussion of the theory behind the process is helpful to those not familiar to electrostatic separation. Charging and sepa¬rating slags, dry minerals or other materials by ion bombardment is the most common form of electrostatic separation. Millions of tonnes of minerals are processed each year by this method. In an ion bombardment separation, granular material is fed onto a grounded metal cylinder (or roll) and charged by a corona-producing electrode placed above the roll's surface (Figure 2). While both conductors and non¬conductors become charged, only the conductor is able to lose its charge. The charged non¬conductor, as it rests on the roll's surface, "sees" an oppositely charged image of itself in the metal surface. It is attracted to the image charge, becomes electrostatically pinned to, and moves with the roll's surface. The conductive particle also sees an image and is attracted to it. But upon touching the roll's surface, it discharges rapidly to the grounded surface and is thrown free from the roll's surface with a projectile motion. In the case of precious metal slags, the con¬ductive particles would be metallic prills of dore metal; and the nonconductive particles would be the slag, free of metal. Middling grains, generally, are in the form of a metallic prill encased in or incompletely liberated from slag. LABORATORY TESTING A number of precious metal slag samples have been tested in the laboratory. It has been found that the composition of slags vary widely from one refinery operation to another. Typical laboratory procedure is to crush and size the slag followed by two-stage lab-scale electro¬static separation. The conductor fractions from the first and second pass are then combined as a prill concentrate; middlings fraction and clean slag tailings from the second pass are held separate. Selected results from laboratory testing are shown in Table 1. It is important to note in Table 1 that the assays represent overall silver and gold, not metallic values. From experience, the laboratory results are typically lower in grade and recovery than the industrial installations. This is largely due to the hydroscopic nature of precious metal slags coupled with the high local humidity in Carpco's Jacksonville, Florida, location. Relative humidity in Jacksonville can range form 60-95%, while most mining locations in the

Jan 1, 1987

By T. Estelle Gardner

Heat-capacity measurements were made over the range 8° to 350° K on beryllium sulfate dihydrate and beryllium sulfate tetrahydrate using an adiabatic calorimeter. No anomalies were noted in the curve for either compound. Smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated from the heat-capacity data at 10° K intervals and at 273.15° and 298.15° K. The entropy values calculated at 298.15° K were 39.01 ± 0.12 entropy units (eu) for the dihydrate and 55.68 ± 0.17 eu for the tetrahydrate.

Jan 1, 1967