Search Documents

By Shaik Jeelani, Esperidiana A. B. Moura, Vijaya K. Rangari, Roberta A. Lima, Rene R. Oliveira

This work present the preparation and characterization of biodegradable nanocomposites based on aliphatic-aromatic copolyester (PBAT)/polylatic acid (PLA) blend reinforced by TiO2 nanoparticle. The biodegradable polymeric nanocomposites were prepared by melting extrusion process using a twin-screw extruder machine. The influence of the TiO2 nanoparticle addition on mechanical and thermal properties of PBAT/PLA blend was investigated by tensile and impact tests, SEM, DSC and XRD analysis and the correlation between properties was discussed.

Jan 1, 2015

By Wenying Liu

The effect of aeration on chalcocite heap leaching was studied by analyzing the historical data from two chalcocite heap leach pads located in Chile, one with aeration and the other without aeration. The data showed that the copper leaching kinetics of the aerated heap was greater than that of the unaerated heap within a certain leaching period, after which there was no effect of aeration on the copper leaching kinetics. The total acid consumption per ton of ore processed was higher in the case of aeration, which was supported by the higher pH of the PLS. But the net acid consumption per ton of copper produced was the same in the two cases. Approximately 5% of the total iron added to the unaerated heap was precipitated inside the heap. In contrast, there was no net iron precipitation or generation inside the aerated heap. Bacteria activities were thought to occur even in the unaerated heap, but the extent was much less than in the aerated heap. Given the importance of forced aeration in chalcocite heap bioleaching, mathematical modelling will be applied in the future work to assist the optimization of the aeration system design.

By James C. Sever

"With the advent of high energy costs and increasing concern for the environment leading to the incorporation the C02 life cycle as a criteria for the material used in a finished product, it is beneficial to analyze the plant and the process used in producing a raw material in order to identify practical, economic energy recovery opportunities. To this end a study was made of the proposed Nevada Clean Magnesium, Inc. Tami-Mosi reduction facility. Each source of waste heat is listed together with the assessment for potential co generation or direct recovery. The overall impact on energy requirement and C02 generation is provided.IntroductionHistorically metal reduction plants, large consumers of energy, do not recover waste heat. This occurred for many reasons:• Energy costs were low and the capital for a co-generation system could not be justified;• Waste heat sources contained entrained solids or liquids which would inhibit efficient energy recovery;• The exit temperature for the heat source was too low for efficient use by aaqueous Rankine cycle system.The business environment has now changed adding impetus to the recovery of energy previously discarded. Power costs have greatly increased. Global warming and the impact of carbon dioxide on the environment has become an issue which could impact the permitting of a plant. Technology improvements especially the development of a scaling environment waste heat boiler [l] and the development of the organic cycle Rankine cycle recovery system enable up to 70% energy recovery from ""low grade"" heat sources [2].With the inception of Nevada Clean Magnesium, Inc. 's (formerly Molycor Gold Corporation, Inc.)Northern Nevada Tami-Mosi project [3], an opportunity was presented to incorporate energy optimization from the initial design phase."

Jan 1, 2013

By Gregor Mori

Niobium electrolysis has been performed in a NaCl-KCl-NaF-NbCls electrolyte. By means of electrolytic .refining the average valency of the niobium ions was determined as well as the crystallization behaviour. In electrowinning runs the influence of the main parameters such as temperature, RF (mole ratio F/Nb), chemical prereduction, niobium content of the melt and current density has been determined with respect to low specific energy consumption and high purity of the deposit.

Jan 1, 1995

By Juha Järvi

Outokumpu Zinc Oy has two separate roasting lines with fluidized bed furnaces and waste heat boilers for calcine collection and heat recovery. During the last 30 years, zinc production in Kokkola plant has increased continuously and at the same time the raw materials have changed. Therefore, the waste heat boiler has been under continuous research and development. The waste heat boiler plays a significant role in the process and consequently the reliability and efficiency of the device is important for the effectiveness of the entire process. Many changes have been made to the boiler in the last decades. New radiation tube screens, tube bundles, and baffle-plate constructions have been added to the boiler and also rapping systems for the dust have been developed. The latest improvement to the boilers was a baffle wall, located in the middle of the radiation section roof in the first boiler, and baffle plates in the lower part of the convection section in the second boiler. The new boiler design and optimization were carried out using physical water and air-dust modeling as well as computational fluid dynamics. The modeling work agrees well with experiences in practice. The latest developments have increased the operating hours per year and the effectiveness of the waste heat boiler.

Jan 1, 2002

By Zongliang Zhang

Electrowinning is a significant step in metal extraction processes. Because the nature of electrowinning is to reduce metal from its oxidized state, substantial energy consumption accompanies it. Electrowinning processes of different metals have much in common—the deposition of the metal on the cathode and the counter-reaction on the anode. An advanced model was developed that can be applied to a variety of metal electrowinning processes. A model for specific metals can be readily obtained by modifying parameters such as potential, kinetics, and side reactions in the model. The model incorporates mass transfer, gas-liquid flow, electrochemistry, and deposition, making it a comprehensive electrowinning model. The model is applied to copper, nickel, and zinc and verified with the experimental results. In addition, the parameter settings and results of different metals were compared, showing that this model has great versatility and accuracy, thereby making it an efficient and effective research tool.

By A. J. Paul, K. O. Yu

"Today, foundries are moving towards the use of models and design tools to gain a competitive advantage in producing castings of high desired quality. This leads to a growing alliance between foundries, software developers and researchers seeking to model, visualize and understand the phenomena taking place during the casting process. In addition, there is a need to develop affordable techniques to produce parts in small lot sizes. This leads to the development of a Flexible Manufacturing System consisting of: (1) up-front computer-aided engineering; (2) computer integrated proto typing with solid freeform fabrication; and (3) fabrication of the actual mold and related equipment to cast the part.This paper discusses some of the developments that are taking place today in the areas of modeling the physical phenomena during the casting process as well as towards developing a Flexible Manufacturing System for producing cast parts. Areas that require most work involve prediction of defects and mechanical properties using simplified analyses. In addition, electronic data sharing for collaborative engineering between geographically dispersed team members is also discussed. Case studies are presented showing successes as well as failures.IntroductionCasting, one of the oldest forms of metalworking, has recently seen a flurry of developments in the area of solidification modeling. These developments have come about after the realization that, in order to stay competitive, foundries need to reduce their scrap rate and production costs, and increase casting quality. Even though this is not new knowledge for foundry engineers, the tools to help them achieve this goal are just being developed and put in place for use by foundries. Several state-of-the-art software packages are currently available to analyze the solidification behavior in complex shaped castings. These packages make use of several different approaches for solving the various problems associated with casting processes. The overall architecture of a comprehensive solidification modeling system is shown in Figure 1."

Jan 1, 1994

By Lilong Zhu, Shaoda Zhang, Qian Wang, Shengping He

The effects of ZrO2, Y2O3 and Sc2O3, which are transition metal oxides, on the melting temperature, viscosity at 1300 °C, and break temperature of three mold fluxes (two weak-reactive type and one non-reactive type) designed for the high manganese and high aluminum steels, and one another conventional CaO-SiO2 based mold flux is studied. The results indicate that the melting temperature and viscosity increases slightly, and the break temperature increases dramatically with the addition of ZrO2, Y2O3 and Sc2O3 content in the conventional CaO-SiO2 based mold flux system. While, the addition of ZrO2, Y2O3 and Sc2O3 in the weak-reactive or non-reactive mold flux systems has a negligible in fluence on the melting temperature, viscosity and break temperature, suggesting that these transition metal oxides are possible to regulate radiation heat transfer without changing the basic properties of mold fluxes.

Mar 1, 2018

By Suzzann Nordwick

Over the past decade, significant advances have been made in the development of sulfate-reducing bacteria (SRB) technology to treat acid mine drainage (AMD). Bench-scale testing, field demonstrations, and engineered applications of SRBs for the treatment of AMD will be presented. Designs include an in situ bioreactor installed in the subsurface workings of the Lilly Orphan Boy Mine in 1994, the SRB bioreactors installed at the Calliope Mine from 1998 to 2001, the integrated biological reactors built at the Surething Mine in 2001, and the ongoing development of a replaceable cartridge system. SRB technology benefits include the reduction of dissolved metal ions to insoluble metal sulfides and the neutralization of the AMD resulting from the production of bicarbonate from the oxidation of organic nutrients. This paper will address engineering design criteria including the selection of organic media and system permeability and complete mitigation of AMD. Research was funded under Interagency Agreement No. DW899388-70-01-1 between the US EPA and the US DOE and was conducted by MSE Technology Applications, Inc., through the National Environmental Technology Laboratory (DOE Contract No. DE-AC22-96EW96405) at the Western Environmental Technology Office located in Butte, Montana.

Jan 1, 2003

By Pranav Deshpande

The wear behavior of metal matrix composites differs from that of the monolithic metallic counterparts because composite materials have multiple constituents in their structures and these constituents wear at different rates. It was observed that under low wear stresses, abrasive wear prevailed. As the wear stress increases, pullout of reinforcement occurs and both abrasive wear and wear due to pullout contribute to the overall composite wear. A model of wear taking into account both types of wear has been developed. A critical pullout wear stress was suggested for each composite. Below the critical wear stress, no pullout of reinforcement occurs. It turns out that the critical wear stress simply equals to the ratio of the interfacial strength between the matrix and the reinforcement to the friction coefficient between the reinforcement and the wear counter surface. The critical wear stress is independent of the particle size of the reinforcement. From data on wear of 53% WC composites, the equation of wear for 32% WC composites was obtained. Experimental results agreed well with the predicted wear rate of this composites. This provides an excellent verification of the wear model developed by Lin and Deshpande. Wear data from Modi et al. in the literature were also perfectly fitted with the model.

Jan 1, 2006

By D. I. Chalmers

The Brockman rare-metals and rare earth resource is located within volcanic and volcanogenic sediments of the later Proterozoic Halls Creek Group in the East Kimberley region of Western Australia. Exploration including surface trenching, percussion and diamond drilling has defined a major resource of rare-metals and heavy rare earth elements. The host&apos; is a steeply dipping ash-flow tuff, described informally as the Niobium Tuff, enriched in zirconium, hafnium, yttrium, niobium, tantalum, rare earth elements, gallium and beryllium. The mineralization is fine- grained (<20 micrometres) and is the result of alteration and re- mobilization of comparatively simple precursor minerals such as columbite and zircon by fluorine-rich deuteric solutions that were retained in the tuff following eruption. The ultra fine-grained structure of the tuff precludes mineral liberation and separation by physical methods. However, values can be converted to water soluble sulphates by reacting with concentrated sulphuric acid at 250°C. The solution containing aluminium, niobium, tantalum, zirconium, hafnium, yttrium, rare earths and gallium can then be processed to pure products in a sequence of solvent extraction and ion-exchange steps. As a result of these processing techniques, the commercial products obtainable from the resource include mixed rare earth and yttrium concentrates, zirconium-hafnium concentrate, niobium-tantalum concentrate and ceramic grade alumina. Further separation could result in high purity products suitable for ceramic and electronic applications.

Jan 1, 1992

By Seyed Mohammad Taghavi

In this report, the efficacy of different factors such as temperature of reaction, time of reaction and depth of bed are investigated in a process of recovery of zinc oxide from zinc ore concentration residues in a fluidized bed furnace. Under optimum conditions, there was more than 93.5% zinc oxide in products.

Jan 1, 2006

By L. N. Ertzeva

The present work is dedicated to investigation of the sulfidizing process of ore pyrrhotite concentrate with recovery of a sulfide material, enriched with non-ferrous metals, and waste pyrite, with downstream separation by a certain beneficiation method.

Jan 1, 2006

By Benjamin Vidales

Copper in concentrations above 0.5 weight percent in iron and steel causes hot shortness. This tendency is intensified in the presence of dissolved tin above 0.05 weight percent in the alloy. The understanding of the mechanism of removal of copper from molten iron and steel is of industrial importance. In this investigation, we present the experimental results of the removal of copper from molten iron using sulphide flux in the temperature range 1000°-1500°C. The solution thermodynamic properties of binary sulphide melts have been estimated by using the relevant phase diagrams and the behaviour of copper sulphide in these melts is discussed. The kinetics and thermodynamics of the removal reaction are also explained and, the experimental results are also reported showing the equilibrium distribution of copper and sulphur in molten iron.

Jan 1, 1995

By Jürgen Antrekowitsch

Typical zinc oxides recovered from wastes like steel mill dusts and neutral leaching residues are of a low quality because of impurities like fluorine, chlorine, lead and others. Therefore, they are not comparable to technical grade zinc oxides produced in “French” or “American Process”. Some new developments, most of them still in pilot scale, try to establish processes where higher qualities of the product should be achieved. Zinc oxides are not only supposed to be an input material for electrolytic zinc production. Far more, they should find their way into the zinc oxide market as a substitute for technical grade zinc oxides. Furthermore, a new field of application for these oxides has been investigated at the department of Nonferrous Metallurgy, University of Leoben. Because of a higher acceptance concerning different impurities in relation to zinc winning electrolyses, a use in electrolytic galvanizing shows an interesting option. Therefore, synthetic zinc oxides with different impurities were generated to study the effect of these impurities especially on the quality of the zinc layer. Typical steel sheets, as used for car bodies, were electrolytically galvanized and the resulting layer was analysed, as main impurities compounds of fluorine, chlorine, iron, lead and calcium were used for the investigations. Beside the layer quality, the current efficiency and the possible galvanizing speed were examined. The results give an indication, weather such an alternative application can be feasible from a technical and economical point of view or not. 597

Jan 1, 2008

By José Luiz Rodrigues Bravo

The production of electrolytic copper with assured quality corresponding to international standards, in a conventional electrorefkery of a custom smelter, is a hard and cautious task, if no advanced technologies for selective control of electrolyte impurities are available. The improper control of the amount of As , Sb and Bi in the anode that enter the tankhouse , attributable either to a bad schedule of concentrate input or to the unavailability of clean concentrates in the international market , as well as the lack of means to maintain the suitable level of these elements in the electrolyte together with other operational circumstances, can result in off-grade copper, as well as affect the starting sheet chemically and physically. This paper presents in a practical way the relationship between the operational conditions and the cathode and starting sheet quality produced at CMSA, covering the period of the last five years of operation, discusses the technologies available in the market for antimony and bismuth removal and compare the results of testwork, achieved in the laboratories of CMSA, using two resins not associated with patented technologies.

Jan 1, 1997

By John E. Litz

Metal-bearing flue dusts are produced by some ferrous and non-ferrous industries. Many dusts are being or can be treated for recovery of metal values. Operating and proposed flowsheets for the most common dusts are reviewed. Advantages, disadvantages, product marketability, and cost implications are discussed for each flowsheet.

Jan 1, 1992

By Richard Hollis

The Mount Isa copper smelter was expanded in 1998 to a capacity of over 250000 t/y anode copper. This tonnage will be produced from a single stream consisting of an Isasmelt smelting furnace, and four Peirce-Smith converters - one of which was installed as part of the expansion project. During the course of the expansion project Mount Isa Mines Limited (MIM) signed an agreement with WMC Fertilizers Ltd (WMCF) to supply sulphur containing smelter gases over the fence to a new sulphuric acid plant to be built by WMCF. This will result in a further increase in copper production by reducing the time when smelting is curtailed by Air Quality Control restrictions. As well as the need to modify the primary gas system to connect to the acid plant, the hoods and crossover ducts and their support structures on the original three converters required replacement, and secondary ventilation was also needed to improve converter aisle hygiene. Each of these areas was addressed by the project. Preliminary ideas for carrying out the modifications were found to have a serious impact on converter aisle operations, and would have led to a production loss of over 50000 tonnes of copper. Following benchmarking in other copper smelters, a suitable construction plan was developed and carried out to minimise this loss. This paper describes the methodology and construction plan adopted.

Jan 1, 1999

By D. J. Goodwill

BHP Copper operates a 3,400 tpd dry concentrate, single burner, Outokumpu flash smelting furnace (FSF) at their San Manuel copper smelter in Arizona. The very fine (-325 mesh), dry concentrate is fed to the burner from a 550 metric ton (nominal) capacity furnace feed bin via two drag chain feeders. During the 10-year history of the furnace, operations have been plagued by serious flooding problems. The fine concentrate sometimes becomes aerated during discharge from the bin and flows like a fluid at very high uncontrollable rates to the burner. This results in upset conditions at the concentrate burner leading to poor furnace metallurgy. This paper will examine the problems of uncontrolled feed from the furnace bin (i.e. flooding), and&apos; instantaneously feeding a flash smelting burner. It will show that a drag chain is a poor choice of feeder when high rates are needed, and that drag chains always produce a funnel flow pattern in a bin. BHP&apos;s drag chains cause narrow diameter, high velocity flow channels within the stored material. Consequently, there is insufficient residence: time for the concentrate to fully de-aerate before discharge, hence flooding occurs. In addition to the flooding problem, drag chains create a pulsating flow to the concentrate burner due to the tendency for material to slough off in discrete chunks at the discharge end of the slow moving chain conveyor. During the scheduled FSF rebuild in May 1999, BHP intends to remove the drag chains, modify the bin to a mass flow design and to use STAMET® multi-disc feeders to accurately and instantaneously control the rate of discharge from the bins. Air slides will be used&apos; to convey the concentrate to the burner.

Jan 1, 1999

By C. Flores

The direct cementation of copper from a loaded D2EHPA 20 % vol. in kerosene using zinc, zinc-lead alloy and iron metallic powders was studied. Copper was loaded into the organic solvent from an aqueous copper sulfate solution. Results indicated that copper is reduced spontaneously with relatively fast reaction rates. The effects of several operating parameters such as water content in the organic system, initial copper concentration, reductant surface area, oxygen and nitrogen atmosphere, intensity of the agitation and temperature on the galvanic stripping of copper were studied. For a better understanding of the electrochemical reactions involved in the galvanic stripping, the dissolution of metallic copper in the organic solvent was also studied. Copper did not dissolve unless a small amount of water was present in the organic system. The results and possible reaction mechanisms are discussed.

Jan 1, 1999