Search Documents

By Florian Kongoli

The optimal operation of the blast furnace depends considerably on the properties of the sinter fed into the furnace. As a result, the optimization of the sintering processes has a direct effect on the overall effectiveness of the iron making processes. In order to produce a good sinter special care needs to be taken in order to assure it has a good permeability and reducibility and it is able to retain these properties for a certain time. If the sinter starts to melt down early in the upper part of the blast furnace, where its solid state reduction is essential, permeability decreases, the gas channels get blocked, reductibility diminishes and serious problems may also follow. Among the factors that influences the above mentioned sinter properties are the oxygen potential and fluxing components. Nevertheless, their effect on the phase relations during sintering and sinter reduction conditions has not yet entirely clarified and confusion exists in literature. This quantification becomes even more important today where many new minor components such as Al2O3 and MgO enter the sinter through raw materials. This work quantifies the effect of oxygen potential and fluxing components such as alumina and magnesia on the liquidus and phase relations of the sinter primary melts in the iron rich portion of CaO-FeO-Fe2O3-SiO2 system at sintering conditions. This is carried out by the means of new type of industrial diagrams in the form of Fe/CaO vs. SiO2 that can directly help the optimization of the sintering processes.

Jan 1, 2006

By Laihua Wang, Peter Hayes, Hae-Geon Lee

"This paper introduces a new process for the efficient removal of dissolved gases and inclusions from liquid metals. This process involves the creation and dispersion of fine bubbles in molten metals by introducing inert or reactive gas into a region of turbulent flow. The highly turbulent metal flow splits the gas into fine bubbles and results in good mixing between the gas and molten metal phases. These conditions are ideal for contacting inclusions in the metal with the bubbles and subsequent flotation of the inclusions to the metal-slag interface where the inclusions are then absorbed by the covering slag layer. Dissolved gases, such as [H], [0], [N] in the metals are also transferred to the gas bubbles and removed from solution.The process concept has been previously demonstrated using a full-scale air/water model to simulate the ladle-to-tundish system of continuous casting of steel. The present cold modelling work has further demonstrated the ability of the process to remove gas solutes. The results indicate that the efficiency of new process is several hundred times greater than that of conventional high speed rotating injectors which are currently applied in the treatment of liquid light metals.IntroductionDuring metal smelting, refining and alloying processes, unwanted gas and second phase liquid or solid impurities are incorporated into liquid metals. In the case of steelmaking, the gas-forming impurities include [0], [H] and [N], and the solid impurities as a result of deoxidation include Ah03, Si02 inclusions. Common impurities in liquid aluminium are dissolved hydrogen and solid Ah03. To avoid subsequent problems during processing and to improve the physical properties of the metal products it is necessary to significantly reduce the level of impurities."

Jan 1, 1996

By Serge Lavoie

Alcan's Guillaume-Tremblay plant, located in Jonquiere, Quebec, has been in operation since 1990. This was the first plasma dross processing plant ever built. In addition to the use of the plasma heating technology, Guillaume-Tremblay has other unique features making it a modern and efficient dross processing facility. This paper presents a general overview of the practical experience at the Guillaume-Tremblay plant. In particular, the utilization of plasma heating in industrial conditions, the metallurgical performance, the unique dross handling system, the control and information management system and the reclaiming of the by-products will be discussed. Finally, the use of the plasma process for salty dross will be addressed' briefly.

Jan 1, 1995

By Jouko Kallionen

Advanced Flotation Technology is the application driven design of flotation cells to achieve the optimum performance for each type and grind of flotation. This can be applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Standard, engineered, components are matched to provide mechanism design and cell dimensions for each case according to feed parameters and flotation type. Advances in process control have been achieved with high level controls and operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed. Excellent results of this Advanced Flotation Technology in large scale porphyric copper ore have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified.

Jan 1, 1999

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By A. Buzaianu, P. Motoiu, G. Popescu, C. A. Popescu, I. Rusu, A. F. Olteanu

"In recent years, the recycling magnesium metallurgy has developed new types of alloys, some of which exhibiting special electrochemical characteristics. Their application has found a fertile field in the energy conversion technologies. The paper introduces some technologic data on the recycling of aeronautical parts and scrap materials generated from the disassembling of magnesium alloy components, attempting to also solve the recycling of magnesium painted parts. The approach is meant to establish a superior quality method for recycling discarded parts or the excess of re-melting material in order to reduce environmental impact and costs. Magnesium-base alloys used as anodic materials are characterized by a high uniformity of the structural properties as well as by superior electrochemical performances, as compared to the ""classically"" used materials: Zn, Pb, etc. In nonconventional applications of magnesium alloys used as sacrificial anodes working in seawater, special alloying elements contribute to improving anodic processes. The influence of these alloying elements on magnesium sacrificial anodes was studied. It was found that the use of recycled materials in anode manufacture could reduce the Mg alloy cost by as much as up to 75% of the cost for virgin material, including the costs for the entire sequence of collection and transportation from a molding factory to a refinery, re-melting and composition adjustment.1. IntroductionMagnesium alloys are valuable materials because they exhibit low density, good forming and machining qualities, particular electrochemical properties and have a high recycling potential. There exists a false idea about the high costs of the use of magnesium alloys, partly justified by the lack of secondary materials suppliers and the insufficient knowhow in the diverse user industries to provide for an efficient substitution of conventional magnesium alloys for multipurpose applications. These circumstances have lately spurred the magnesium industry to develop new alloys and coatings and to improve processing techniques [1]. As a result, magnesium supply has greatly expanded and so have the research and development efforts to achieve complete recycling of Mg alloys.In consumer markets, magnesium is frequently selected because it helps reduce enery consumption. For example, an equal volume part made of magnesium is 23% the weight of a steel part and 64% the weight of an aluminium part."

Jan 1, 2008

By S. S. B Wang

Zirconia-based ceramic materials have potential applications in high temperature furnace insulation, hot extrusion and casting dies, pressure nozzles, cutting tools, engine parts and electronic materials. High purity and superfine powders of zirconium oxide (baddelyte) were synthesized from a solution containing zirconium oxychloride and urea under hydrothermal conditions. crystallization of the metastable tetragonal zirconia using magnesium oxide or yttrium oxide as stabilizing agents was successfully achieved. The mechanism of hydrothermal reaction to produce these powders are discussed.

Jan 1, 1989

By Vaughan R. Voller

"Numerical methods for dealing with a temperature dependent conductivity are discussed. An approach based on a local application of a Kirchhoff transformation at the discrete level is presented. The application of this transformation - that does not require any inversion- is demonstrated on solving a two-dimensional test problem.IntroductionMuch is said in the recent literature on the modeling necessity of obtaining appropriate thermo-physical properties; in particular the requirement to account for properties that are ""strong"" functions of the depended variables, e.g., Temperature. Of course obtaining appropriate thermo-physical properties serves no purpose unless they can be accurately integrated into a discrete numerical calculation. The purpose of this paper is to examine how temperature dependent conductivities that exhibit discontinuities or rapid changes can be handled in a numerical code.The discussion will be made in the context of a control volume finite element method [1]. After a brief outline of control volume finite element fundamentals basic methods of dealing with discontinuous or rapidly changing thermal conductivity are discussed. This is followed by the presentation of the recently proposed local Kirchhoff method [2,3], The paper concludes with an investigation of the performance of the various conductivity schemes in solving two dimensional problems. This testing clearly shows the advantages (accuracy and implementation) in using the local Kirchhoff method."

Jan 1, 2001

By Osvaldo A. Bascur

Several new hydrometallurgical plants have been built in the past years. They have implemented new processes to treat new type of ores. New technologies have been used to improve metallurgical performance from the start. The cycle times between knowledge generation and innovation are often neglected in the traditional capital expenditures and building of these new process plants. The paper reviews several implementations in which they have started with new ways of using information management from the beginning. The implementation of a real time performance management infrastructure is reviewed to assist in the implementation of mine to product strategies, metallurgical mass balances, solvent extraction composition statistical process control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to improve operations by simplifying the access and analysis of information from assets and metallurgical processes. Continuous improvement and innovations have been enabled to minimize start times and for faster troubleshooting and resolution of operational problems.

Jan 1, 2006

By Allan J. MacRae

A copper alloy to be used for coils in cast copper cooling blocks has been identified and samples prepared for metallurgical examination and destructive testing to compare with cast cooling blocks manufactured from copper and nickel-copper alloy pipes. The copper alloy allows for the formation of a metallurgical bond between the pipe and the cast copper during the casting process, which does not normally occur with pure copper or nickel-copper alloy pipes. The alloy's coefficient of thermal expansion is also much closer to that of pure copper compared with nickel-copper alloys, so there is less strain induced at the pipe-cast copper interface due to differential thermal expansion. It is expected that this new pipe coil alloy and associated casting techniques will allow for the production of cast copper cooling blocks that have greatly enhanced service life in high heat load applications compared to existing technologies.

Jan 1, 2002

By Roger W. Lee

The commissioning of the prototype Imperial Smelting Furnace (ISF) in 1950 was a technological breakthrough in the pyrometallurgical smelting of zinc and provided significant advantages over the existing retort processes. However, for most zinc concentrates the electrolytic zinc process continued to be more economic. Therefore, the Imperial Smelting Process (ISP) specialised in smelting zinc and lead concentrates that were less amenable for treatment by either the electrolytic zinc process or the lead blast furnace. Subsequently, improved mineral processing techniques led to a decrease in the availability of these concentrates so the treatment of secondary materials in the ISP assumed greater importance. This was facilitated by the development of techniques such as hot briquetting and tuyere injection. In 2002 over 1 million tonnes of zinc and 400,000 tonnes of lead were produced by the ISP. However, in the 2002-3 the economics of the Process became extremely difficult because of low metal prices and increased operating costs. This resulted in the closure of four ISP smelters in 2003 and two in 2005. Nevertheless, two new ISP smelters are scheduled for commissioning in China in 2006 where local economic conditions continue to favour the process. The economics of the process are examined particularly in respect of smelter margin and operating costs. The need to increase the smelter margin means that the future of the process will be closely linked to its ability to consume secondary materials and an examination will be made of its potential for conversion to 100% secondary operation. Apart from a reduction in raw materials costs, a substantial reduction in operating costs would ensue from not operating sinter and sulphuric acid plants.

Jan 1, 2006

By J. M. D. Wilson

An analytical program using a combination of SEM-based image analysis techniques is developed for automated modal analysis of ores containing silicate and other gangue minerals. Previous knowledge, gathered by means of either optical microscopy, X-ray diffraction, SEM, or electron microprobe analysis is used to establish discrimination criteria in the image analysis program. The program initially discriminates minerals on the basis of their relative grey values in a backscattered electron image. For those minerals which have overlapping grey levels the minerals are identified by the program using energy dispersive X-ray spectrometry with X-ray counting for twelve or more elements. This technique is useful to quantify ores in which the gangue minerals are numerous. Two cases of application are presented.

Jan 1, 1999

By William Bourcier

Geothermal Brines are a significant potential source of valuable minerals and metals. These brines are water that is heated by the natural heat flow from the depths of the earth. Hotter brines, typically with temperatures greater than 120°C, are used to generate electricity. Lower temperature brines are directly used to supply thermal energy to applications such as agriculture, aquaculture and process/domestic heat. The geothermal waters have had intimate and lengthy contact with the layers of the earth?s crust that they flow through, resulting in dissolution of minerals and metals from the rocks, and solution into the hot water. These aqueous solutions can be processed to recover minerals and metals. Some potential products include silica, zinc and lithium, along with other materials. Recovery of minerals and metals from geothermal brines can be viewed as ?solution mining by nature?, followed by application of known or new hydrometallurgical techniques for isolation and purification. This paper discusses the opportunities, the processes, the challenges, the current status, the economics and the potential for recovery of minerals and metals from geothermal brines.

Jan 1, 2006

By Edwin de Jesús Deveaux

After 32 years of operations beneficiating lateritic nickel ore in a fully integrated pyrometallurgical complex, Falconbridge Dominicana (FALCONDO), situated at Bonao and La Vega Provinces, Dominican Republic, has become profitable with one of the lowest nickel grade content processing plants in the world, and literally without any by-product (granulated slag, will be utilized in the future as a post-processing subproduct). To December 2002, mineral reserves were 64.1 million tonnes containing laterite grading as low as 1.15 % Ni when full dilution is applied. At a cut-off grade of 1.20% Ni, the reserves will provide 15-20 years of production. The mineralized thickness over the seven active deposits averages 6 m. Development of very selective and unique mining practices, together with improvements in the process plant, are key to achieving the production goal (30 kt Ni/yr) and to meet the quality standards for the ferronickel produced. Keywords: Laterites, grade control, mining methods, environment

Jan 1, 2004

By Klaus Gamweger

There are different reasons for purging a metal bath. The operations are varied, for example the purging gas can be used as a reactive gas being part of the metallurgical process or as an inert gas using the rising gas bubbles for agitation only. The different purposes for agitation, chemical and thermal homogenization or a preferential movement of the slag to the slag skimming door have to be considered. It depends on the furnace type and its dimensions as well as the process characteristics what the focus is on. For an optimized arrangement of numbers and position of all single plugs in the furnace, mathematical modeling - the CFD Computational Fluid Dynamics method - is used. This paper shows how the operation of purging plugs can influence the metallurgical process of an anode furnace by the example of Jinchuan Copper in China. The potentials for savings in energy consumption as well as in time for oxidation and reduction are presented.

Jan 1, 2006

By Oscar Jaime Restrepo, Juan Camilo Restrepo, Jorge Ivan Tóbon

Portland cement is obtained by a conventional synthesis process from a mixture of limestone and clay at high temperature (1450 °C). This work reports the possibility to obtain cement silicates via alternative methods like Solution Combustion Synthesis (SCS), which optimize both time and temperature, and the consequences to energy efficiency and mitigation of CO2 emissions. The production of one ton of cement emits between 0.62 and 0.97 tons of CO2 into the atmosphere. In this process the CO2 emissions are between 21 and 59%. The combustion methods are chemical redox processes in which, at high temperature, a self-sustaining and fast wave is generated from using chemical precursors and organic fuels.

Jan 1, 2016

By Susumu Imashuku

A pseudoternary phase diagram of the BaO?ZrO2?ScO1.5 system is established and the conductivities of the scandium-doped barium zirconate are measured in wet conditions. According to the phase diagram, the molar fraction of scandia in the barium zirconate phase that equilibrates with the cubic zirconia (ZrO2) and scandia (Sc2O3) phase is 0.03. On the composition line, where the molar fraction of barium oxide (BaO) is 0.50, the solubility of scandia into barium zirconate is 0.27 as a molar fraction of scandia. At around 500 °C, the conductivities of scandium-doped barium zirconate are estimated to be almost same as that of yttrium-doped barium zirconateThe activation energies for bulk proton conduction in scandium-doped barium zirconate (0.57 eV for BaZr0.90Sc0.10O3-d) are higher than that of yttrium-doped barium zirconate (0.44 eV for BaZr0.90Y0.10O3-d). In addition, the bulk conductivity of scandium-doped barium zirconate in this study is 10 times higher than the reported conductivities in the temperature range of 75 °C to 300 °C.

Jan 1, 2006

By Vânia L. L. Andrade

Igarapé Bahia Mine is located in Carajás area, northern Brazil. Currently Companhia Vale do Rio Doce operates there a CIP / heap leaching plant treating an oxide gold ore containing about 4 g Au /t and 0,2% Cu, which produces 11 t of gold per year. Recent geological survey has identified a signifcant copper-gold reserve underneath the oxide gold ore. The processing aspects of this copper-gold sulphide ore are described in this paper. It includes ore characterization studies, grinding and flotation tests, orebody variability assessment, flowsheet selection and preliminary economical evaluation Emphasis is given to studies aimed at depressing fluorine bearing minerals to achieve a clean and marketable flotation concentrate.

Jan 1, 1999

By Daniel Adolfsson, Ryan Robinson, Fenwei Su, Jelena Blagojevic

"Cold bonded briquetting of steel plant by-products has proven to be a viable recycling alternative concerning technology, economy and environment in both the traditional blast furnace route and the direct reduction process. A critical parameter in cold bonded briquettes is the type and amount of binder used during production. The binder material must meet certain quality requirements concerning low and high temperature strength, chemistry and economy. Currently, SSAB Tunnplåt uses ordinary Portland cement (OPC) as binder in their cold bonded briquettes. In order to improve binder quality and possibly decrease OPC dependency, a binder feasibility study has been conducted concerning an internal by-product, ladle slag, as a supplement and/or partial substitute for OPC. Several characterization techniques have been used to study the behaviour of ladle slag, these include: XRD, XRF, SEM, glass content analysis, calorimetric analysis, particle size distribution and thermochemical stability considerations concerning the CaO-Al2O3-SiO2 system.IntroductionRecently, a project was initiated at SSAB Tunnplåt AB, in Sweden, which aimed at reducing the amount of ordinary Portland cement (OPC) as hydraulic binder in cold bonded briquettes by partly replacing it with ladle slag. OPC is traditionally used within civil engineering, and widely accepted as a hydraulic binder in a number of different applications. OPC consists of four major crystalline phases, i.e. C3S, C2S, C3A and C4AF. Tricalcium aluminate as well as the ferrite phase in OPC reacts very quickly with water, for this reason gypsum is added to the clinker in order to retard these reactions. The fact that gypsum is present in the system limits the recycling of briquettes to the BOF, since the presence of gypsum during steelmaking results in a significant amount of sulphur emissions. The latter along with the expense that follows, makes it worthwhile to consider alternatives for OPC as binder in cold bonded briquettes."

Jan 1, 2008

By Ann M. Hagni

Electric arc furnace (EAF) dust from the secondary steel industry contains lead, cadmium, and chromium that causes it to be classified as a hazardous waste. Pyrometallurgical treatment of EAF dust is directed at recovering zinc and simultaneously rendering the dust non-hazardous. The mineralogy of the EAF dust is important in determining the occurrence and phase relationships of the zinc, lead, cadmium, and chromium contents. The principle phases in EAF dust as determined by reflected light microscopy, SEM-EDS, and XRD are solid solutions of the iron spinels (franklinite, magnetite, and jacobsite), zincite, hematite, and Ca-Fe-Si glass. Chromium is present in small amounts in solid solution in the spinels. Cyclone sizing of the minus 53 pm particles shows that more than 50% of this size fraction are less than 10 pm in diameter. The <I0 pm particles contain zinc as both franklinite in solid solution with magnetite and jacobsite, and zincite as determined by transmission electron microscopy and XRD. Auger electron spectroscopy did not detect coatings of volatile phases on the surfaces of EAF dust particles.

Jan 1, 1994