Search Documents

By Mark R. Jolly, Jean-Christophe Gebelin, Aleksander Cendrowicz

"Injection of wax patterns is the first stage of the multi-stage process of investment casting. The quality of the final casting and its dimensional accuracy is highly dependent on this stage of the process. Pattern waxes used in the industry behave in a complex visco-elastic-plastic manner. The modelling of such material behaviour is therefore not simple.In this paper a number of configurations of die will be shown in which the injection of the wax has been carried out for a range of processing conditions. Some of the dies are transparent and the movements of wax front observed can be compared with those predicted by simulation. Surface defects in final components will also be shown and compared with the location predicted by simulation software. Some discussion will be presented on the limitations of the software used and the time-scales achieved for practical use as a design tool within the foundry environment. IntroductionThis paper presents the research activities carried out at the University of Birmingham on the modelling and prediction of the behaviour of industrial investment casting waxes during the injection of wax patterns. These research activities are done in the context of a more global study of the fundamental aspects of the investment casting process, the FOCAST project. Regarding the wax injection process, the aim of the project is to achieve a better understanding of the key factors that will lead to better castings. The filling of the die during the injection has been studied. Some other phenomena such as shrinkage/warpage or creep under residual stresses are also studied, but not presented here. Two commercial investment casting waxes have been characterised in order to model their behaviour and predict mould filling and subsequent defects.This paper will present the models that have been used in our work, the simulation packages used, the experiments carried out to validate the modelling and exhibit the defects due to bad filling, and finally the numerical simulation results."

Jan 1, 2001

By Guozhu Ye

Hydrometallurgical zinc recovery from EAF dust has several advantages compared to pyrometallurgical alternatives in terms of low temperature operation, lower energy consumption and higher flexibility. Many hydrometallurgical processes have been suggested and tested over the years without success. The main reasons are: -Low leaching yield of zinc due to the fact that a high fraction of ZnO in the EAF dust exists in the zinc ferrite structure which makes selective leaching of ZnO not possible -Many of the proposals could not handle the halide in the EAF dust To eliminate these two disadvantages, two zinc ferrite elimination concepts have been tested and developed in the REZIN project of the EU 5th Framework Programme. The two concepts for zinc ferrite elimination could be shortly described by the following chemical reactions: A. ZnOFe2O3 + 2CaO = Ca2Fe2O5 + ZnOfree B. ZnOFe2O3 + C = Femet + CO/CO2 + ZnOfree These two concepts were investigated in details in combination with a subsequent leaching step using the novel EZINC process for recovery of zinc from EAF dust. Leaching of pretreated samples has shown great increases of a zinc recovery yield. A zinc recovery of over 90 % could be reached, as compared to about 50 % for no-pretreated samples. This paper will describe the two concepts in details.

Jan 1, 2006

By E. S. Geskin

New material processing tools should be developed and reduced to the practice in order to meet the challenges facing the contemporary material production industry, One of such potentially important tools is supersonic liquid projectiles. It was shown that at the speed of 1500-1750 m/s the water projectile are able to demolish reinforced concrete plates, forge, to pierce and weld metals, to destroy with no explosion non dischargeable mines, etc. These projectiles are generated by simple, low cost launchers run. It is obvious that these projectiles can be applied to the ore mining and comminution. Thermodynamic considerations show feasibility of the use of these projectiles also for smelting, refining and forming. The presented paper discusses the results of the experimental study of supersonic liquid projectiles as well their potential metallurgical applications.

Jan 1, 2006

By K.H. Song, H.T. Son, H.S. Kim, W.Y. Kim

In order to evaluate the grain refining and mechanical properties due to severe plastic deformation (SPD), this wrok was carried out. Convential rolling (CR) and cross roll rolling (CRR) as a SPD method were introduced, and NI-20Cr alloy as an experimental material was chosen. The materials were cold rolledto 90% in thickness reduction ans subsequently annealed at 700oC for 30 min to obtain the fully recrystallized microstructure. For annealed materials after cold rolling, electron back-scattered diffraction (EBSD) analysis was carried out to investigate the grain boundary characteristic distributions (GBCDs). CRR process was more effective to develope the grain refinement relative to CR process, as a result, grain size was refined from 70 um in initial material to 4.2 um (CR) and 2.4 um (CRR), respectively. These grain refinements directly affect the mechanical properties improvement, in which microhardness and yield and tensile strengths were significantly increased than those of initial meterial.

Jan 1, 2012

By Kazuhiro Asai

Hitachi Refinery of Nippon Mining & Metals Co., Ltd. installed a reverberatory type recycling fumace in 1978 in order to treat the industrial wastes which contain metal elements such as copper, gold and silver. Pyrite and industrial waste materials such as galvanizing sludge, hydroxide slime and dust are smelted. Sulfidized copper, iron and precious metals are transformed into matte and other metallic elements are oxidized into slag This copper matte is transported to Saganoseki smelter and copper and precious metals in the matte are recovered. Recently it is difficult to obtain pyrite economically because of the decrease of pyrite production. Therefore, a new treating process of the liquid waste has been investigated at Hitachi Refinery. In this process, the sulfide or sulfate from the liquid waste are smelted as a source of sulfur.

Jan 1, 1997

By J. W. Holzenthaler

Teams continue to play a major role at the Phelps Dodge Mining Company El Paso Operations, especially during the present time of low copper prices. The El Paso Operations' teams have taken the initiative during this copper market downturn and have helped reduce operating costs significantly. Because of this, Phelps Dodge El Paso Operations has continued to grow within the team process by creating a total, non- exempt salaried workforce. In the last year alone, the El Paso Operations have implemented three major initiatives to accommodate the team process. The first was the creation of "guiding principles", a policies and procedures handbook. Second was the "zero and beyond" safety initiative. Third was team compensation. In addition, the Copper Products Company has now adopted a work-team environment, following the lead of the refinery.

Jan 1, 1999

By Robert A. Reiley

Under the traditional environmental paradigm, industry, stakeholders, and government impact the environment through production, consumption, and regulation. For more than twenty years, this paradigm has survived more or less unchallenged. Environmental action has followed a typical pattern: industry pollutes, the public clamors, government enacts legislation, and industry expenditures for pollution-control equipment soar. In the 1990's, many groups realize that command-and-control techniques may not be the most effective method of dealing with environmental issues in the new millennium. The need for regulatory reform became apparent in the 1980's after an accident at the Union Carbide plant in Bhopal, India. In addition, the prospects of an integrated European market and increased global trade sparked a need for common standards regarding the production of goods and services, which led to the adoption of the International Standards Organization (ISO) 9000 Quality Standards. These factors, and others, triggered the development of the Environmental Management System (EMS). Over the past decade, country-and industry- specific EMSs were developed. However, the IS0 realized the need for a single, internationally recognized standard that would be workable for any type organization. The goal of this standard is to promote economic competitiveness, remove trade barriers, and promote environmental protection. To this end, the IS0 14000 Standards were developed to provide business with a structure for managing environmental impacts. This article argues that a new paradigm has begun to transcend the old. Protection of the environment if shifting from "government drivers" to "market drivers". This shift means that industry and stakeholders, instead of government, are taking the lead to develop ways to protect the environment. This article also argues that government can use this new paradigm, in a time of declining budgets and regulatory reform, to continue to protect the environment through increased compliance monitoring and rigorous enforcement. Specifically, the IS0 14000 Standards can allow the government to reduce compliance costs, streamline permit and reporting requirements, and provide business with regulatory flexibility. Finally, this article argues that IS0 14000 will be central to the regulatory reform effort, because it can be internally implemented with little need for legislative intervention.

Jan 1, 1999

By Joo Hyun Park, Kyu Yeol Ko

The viscosity of the CaO-SiO2-xMnO-yCaF2 slags (C/S=1.0; x=10, 40%; y=0 to 15%) was measured to clarify the effect of CaF2 on the viscous flow of molten slags at high temperatures. Furthermore, the Raman spectra of the quenched glass samples were quantitatively analyzed to investigate the structural role of CaF2 in a depolymerization of silicate networks. The critical temperature of the slags abruptly increased at 15%CaF2, which was confirmed to originate from a crystallization of cuspidine using XRD analysis. The viscosity of the slags continuously decreased by CaF2 addition in the 10%MnO system, whereas the viscosity of the 40%MnO system was not significantly affected by CaF2 addition. The effect of CaF2 on the viscosity of the slags was quantitatively analyzed using micro-Raman spectra of quenched glass samples accompanying with a concept of silicate polymerization index, Q3/Q2 ratio. A polymerization index continuously decreased with increasing content of CaF2 in the 10%MnO system, whereas it was not affected by CaF2 in the 40%MnO system. Consequently, the bulk thermophysical property of the CaO-SiO2-MnO-CaF2 slags was quantitatively correlated to the structural information.

Jan 1, 2014

By Shengli Wu, Wei Huang, Xinliang Liu, Kaifa Zhang

The slagging behavior, the phase of primary blast furnace slag and its transformation law of structure for the single furnace burden were studied in this paper. The results showed that the formation of primary slag was controlled by CaO/SiO2, Al2O3 content, MgO content, reducibility, iron content and porosity of the furnace burden. Fayalite (2FeO•SiO2) was easily formed from acid ferrous furnace burden while kirschsteinite (2(Fe,Ca)O•SiO2) was produced from alkaline ferrous furnace burden

Jan 1, 2015

By Aïda Espinola

This work is part of a research program concerning the study of heavy metal removal and selective recovery from electroplating waste waters in the Guanabara Bay ecosystem, preventing the potential noxious retarded effect of landfill, specially in a country of heavy rainfall. A flow-throw cell was employed to adapt to the limits established by the local legislation for disposal in rivers and seas. The cell design is presented and preliminary results show that this cell may be applicable for the decontamination from copper.

Jan 1, 1994

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By Mariane Costalonga de Aguiar, Carlos Mauricio Fontes Vieira, Sergio Neves Monteiro

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850, 950 and 1050°C. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at 1050°C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antonio de Padua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antonio de Padua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption [3,4]. To avoid this problem, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2011

By Toshihiro Tanaka

The information on viscosity and surface tension of molten slag is indispensable to design new refining procedures in ferrous and non-ferrous processes. For example, the authors have tried to develop "Capillary Refining" to remove impurities in liquid metals by applying capillary absorption of molten slag with those impurities into solid fluxes which have a lot of small capillary tubes. It is necessary to adjust the above physico-chemical properties to adequate conditions on the capillary penetration. In the present paper, we discuss our recent trial to predict surface tension and viscosity of molten slag in multi-component systems. We have derived a thermodynamic model to predict the surface tension of molten slag by using ionic size, molar volume and surface tension of pure components. In addition, we have applied neural network computation to evaluate the viscosity of molten slag. We found good agreement of the calculated results with experimental values of the surface tension as well as the viscosity in various slag systems.

Jan 1, 2006

By Tomoji Kawai

"The Pulsed Laser Deposition method using multi-targets is extremely useful for the creation of functional multi-layers and variety of artificial lattices. The topic of the present talk is on the creation of ''Function hannonized artificial lattices by laser ablation"" made of the combined magnetic, ferroelectiric and superconducting layers. The outline of talk is,1. Features of Pulsed Laser Deposition method (Laser Molecular RHEED and S1M/AFM.2. Creation of magnetic, dielectric and superconducting artificial lattices by Pulsed Laser Deposition.3. Novel properties of function harmonized artificial lattices: especially on the magnetic and magnetoresistive artificial The outline of talk is, lattices made of3d transition metal oxides."

Jan 1, 2000

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Half of the input energy to aluminum reduction cell will be lost as waste heat which could be studied for possible recovery. Since price of energy is increasing and the main production cost in primary aluminum industry is energy, so waste heat recovery consideration will be interesting. One of the possible choices for recovering is from aluminum exhaust gases that needs minimum modifications for reduction cell and has no influence on cell heat balance which is vital for the operation. By using heat exchangers with in-line and staggered tube arrangements which placed before fume treatment plant (FTP) we will be able to recover enough amount of heat. The main challenging problem which is necessary to overcome will be the heat exchanger material and its design because of corrosive and dusty exhaust gases from potroom. In this paper, a desalination system with six effects of evaporator is proposed for producing distilled water by using recovered heat from hot exhaust gases. The calculated amount of produced distilled water is around 27,000 / in this specific suggested desalination plant. The suggested desalination plant is based on Hormozgan Aluminum Company data (Hormozal) in Bandar Abbas, Iran which is constructed by the Persian Gulf.IntroductionWaste heat losses arise both from equipment inefficiencies and from thermodynamic limitations on processes. The exact quantity of industrial waste heat is poorly quantified, but various studies have estimated that as much as 20 to 50% of industrial energy consumption is ultimately discharged as waste heat [1]. In order to achieve a final decision for establishing the waste heat recovery plant in any type of industry, a strong feasibility study is mandatory. Also, we need to remember that the possible amounts of energy and suggested process plant for recovery have to be investigated before starting any feasibility study. This kind of study which is important to be finished before moving to feasibility step is mainly a theoretical study, and was done for the Hormozgan Aluminum Company (Hormozal). In addition to the exhaust gases from the potroom, the exhaust gases from anode baking plant appear to have a better potential for waste heat recovery compared to potroom exhaust gases. The average temperature of exhaust gases from anode baking kiln is 120°C higher than the exhaust gases temperature in the potroom. This needs further investigation in a different study, because this study is just focusing on potroom exhaust gases."

Jan 1, 2011

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By Messias dos Santos Machado, Renato B. Godoy, Roberta Lima, Andressa Silva, Francisco Valenzuela-Díaz, Rene R. Oliveira, Esperidiana Moura

This work aims to incorporate the Bof White Clay, from Boa Vista, Paraiba State, Brazil, as natural nanofiller in Ehylene vinyl alcohol copolymer (EVOH) and obtain flexible films. Nanocomposite was obtained using a twin-screw extruder, and film formed using a blow extruder machine. The flexible film nanocomposite was characterized, by tensile tests, XRD, DSC and their properties were evaluated. The results showed a good interaction between the clay and the EVOH resulting in an increase of properties of films nanocomposites as compared to films neat polymer.

Jan 1, 2015

By Godwin M. Beene

Large scale mining operations started in Zambia in 1913 and rapidly expanded during the post 1930 period with the opening of several mining and processing plants on the present Zambian Copperbelt. As a consequence of poor tailings dumps design methods at the start of the mines, and in view of stringent Government Legislation pertaining to environment in the recent years, Nkana Mine has developed a unique method of dump construction at its current tailings depository, Tailings Dam 15A. This method has enabled the revegetation of the dump retaining walls while construction is still in progress, a situation which was not possible on the older dumps. Cowdung has proved to be a superior fertilizer for providing plant nutrients on the tailings. The new method of dump walls construction and walls rainwater runoff drainage system has almost eliminated tendency of gully formation which is common on older dumps, as rainfall on the Zambian Copperbelt comes in intense thunderstorms. The decanted water from the dump is discharged to the natural environment in a controlled fashion after ensuring that it meets the Zambian Government Statutory requirements.

Jan 1, 1999

By V. M. Mukhin

Among the methods proposed for spent activated carbon regeneration, the most acceptable is, thermal reactivation, because in this case the existing equipment for manufacture of activated carbon can be adapted for this purpose. In order to conduct the process of thermal re-activation of spent activated carbon directly at gold mills, a full-scale drum-type furnace with external electric heating has been developed, i.e. EPV-300 model with a throughput rate of 50 to 120 kg/hour. Its use ensures restoration of the adsorption properties of carbon up to the level of fresh activated carbon with an insignificant (by 0.7%) decrease in strength and with a high (95% to 97%) yield of reactivated carbon. During the recent years, activated powder carbon has been extensively used in flotation processes for treating polymetallic ores at ore treating plants to improve recoveries of main metals (copper, lead, nickel, etc.). Especially large volumes of activated powder carbon are used at the Talnakh concentrator of the Norilsk Mining and Metallurgical Complex in Russia for absorption of residual flotation reagents from recycled water in order to ensure efficient selective separation of minerals with similar physical and chemical properties.

Jan 1, 2006

By Tapio Ahokainen

Commercial modeling software and increasingly efficient computers enable today computational fluid dynamics (CFD) to be used as a tool for a more comprehensive understanding of the flash smelting and flash converting processes. CFD modeling can be used for design purposes in many technological areas, but some relevant physical and chemical phenomena are still missing in the commercial CFD solver packages. Therefore, Outokumpu has developed several subroutines for solvers to describe analytically the phenomena in the flash smelting environment. CFD sub-models of the copper concentrate and matte combustion, the particle-particle-wall interactions and for more accurate radiation properties of the gas-particle suspension are needed to ensure reliability of numerical simulations on the flash smelting and converting vessels. Several basic combustion phenomena can be modeled with a number of commercial solver packages, but own models for combustion must be included in the case of sulfides as the feed. Mathematical models for copper concentrate and solid matte combustion have been developed during the last decade. They calculate compositions of the particles and temperature, based on extensive experimental research work in laboratory scale furnaces with validated kinetic parameters and temperature measurements of reacting particles. Inside and near the concentrate burner, the standard particle tracking methods do not include the particle-particle interactions and the particle-wall interaction is too much simplified to describe properly the particle collisions with the distribution cone. Therefore, additional models for the particle-particle as well as particle-wall interactions have been written and implemented. For thermal radiation, models for the emissivity of a gas mixture and for calculating the particle absorption and scattering coefficients have been developed and tested. In addition, the advanced radiation model can be used i.e. in the enhanced simulation of off-gas cooling in the heat recovery boiler area of the flash smelter.

Jan 1, 2006