Search Documents

By A. Valenzuela

During the last years, Chile has been the largest copper producer, either as concentrates or cathodes. Copper obtained via pyrometallurgy is produced by seven smelters, which have carried out modernization plans to increase smelting capacity or to achieve environmental regulations established in the Chilean legislation. Thus, the present work updates technological innovations in smelters, environmental regulations and presents solutions for SO2 handling, particulate matter and arsenic. Also, the authors emphasize the important role of CODELCO Chile, the most important state-owned copper company, in developing technologies such as EI Teniente Converter and EI Teniente Slag Cleaning Furnace,

Jan 1, 2003

By A. Valenzuela

During the last years, Chile has been the largest copper producer, either as concentrates or cathodes. Copper obtained via pyrometallurgy is produced by seven smelters, which have carried out modernization plans to increase smelting capacity or to achieve environmental regulations established in the Chilean legislation. Thus, the present work updates technological innovations in smelters, environmental regulations and presents solutions for S02 handling, particulate matter and arsenic. Also, the authors emphasize the important role of CODELCO Chile, the most important state-owned copper company, in developing technologies such as El Teniente Converter and El Teniente Slag Cleaning Furnace.

Jan 1, 2003

By Manoj Kumar, Vinay Kumar, Nikhil Dhawan, Manish Wadhwa

"Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.IntroductionThe electrical and electronic industries comprising computers, television, mobiles, etc, which are manufactured utilizing printed circuit, boards, capacitors, resistance, soldering material etc. During production, at the end-of service life and degradation due to the advanced version with latest features generate valuable metallic and non-metallic constituents. European Union Council on waste electrical and electronic equipment (WEEE) has classified these into different categories as listed in Table 1 [Streicher-Porte et al., 2005]. Among these the information technology, telecommunications and consumer equipment constitute electronic waste (e-waste) [EC, 2002]. Almost all e-waste consists of an integrated part of printed circuit boards which is a valuable source of several metals such as copper, tin, lead, aluminium, iron, silver, gold, platinum etc. [Relay et al., 1990]."

Jan 1, 2008

By Sudhir C. Dhara

An attempt has been made on the concentration of Platinum Group Metals (PGM) from the converter matte material by microbial .leaching. Biological oxidation of base metal sulfides such as iron, copper, nickel and free sulfur present in the matte material using Thiobacillus ferrooxidans is an alternative method to concentrate the PGM-and gold. The method which produces a platinum group metals concentrate is comparable to chemical processes and electrochemical process.

Jan 1, 1995

By H. Palkowski

Recent trends in the automotive industry lead to increasing interest in advanced high strength steels (AHSS). Those steels often have a high bake hardening potential (BH), giving additional contribution to the strength of structural parts, subjected to the paint baking process. For hot rolled AHSS, namely dual phase and martensitic steels, the effect of process conditions on mechanical properties had been investigated. However, the influence of chemical composition within the range in industrial production has not been investigated sufficiently yet. In the current research, samples with different chemical compositions within the characteristic interval for industrial production are under investigation under different preload conditions and simulating the thermo-mechanical production process. The samples were then subjected to BH process. Tensile tests were performed to study the influence of varying chemical composition on the BH effect. The results of investigations on dual phase steels will be presented in this paper.

Jan 1, 2008

By Wei Gao, Qing-cai Liu, Cun-fang Lu, Huimin Zheng, Jian Yang, Chun-ling Yao

"Mercury in flue gas of coal-fired plants was concerned as another serious pollution when sulfur dioxide pollution was controlled now. The adsorbent made from fly ash by thermal precipitation sulfur to remove mercury in fuel gas from coal combustion plant, SEM, BET, TGA and other measurement methods were used to characterize the effect on surface morphology, sulfur distribution and specific surface. High temperature deposition furnace was applied to increase sulfur content in fly ash based adsorbents produced in lab. The study found that sulfur attached to the adsorbent surface, mesopore and microporous structure, increasing its sulfur content of adsorbent. Sulfur was filled in interspace as small molecule S2, S5, increased their surface area and enhanced their adsorption capacity. The specific surface area increased by thermal precipitation sulfur, and specific surface area which increased with increasing temperature.1. IntroductionThe mercury emission caused by human activity has accounted for 10%-30% of total mercury emission all over the world[11, and the emission from coal-fired power plant have a huge proportion of these emission caused by human activity. Active carbon microstructure and surface morphology play an important role in its adsorption capability, which offers the potential for controlling environmental pollutant, such as sewage, fuel gas, atmosphere and et al [2,31, because it is a material with high specific surface area that long been considered as an excellent adsorbent. At present, include activated carbon, fly ash, calcium-based sorbents and other novel adsorbents. The adsorption capacity and production cost were very important in the process of mercury removal by adsorbents, so the mercury removal has focus on developing adsorbents of highly-efficient. In particular, the waste of metallurgical from coal combustion and the others have a significant advantage about the cost, and they have the highly-efficient in mercury removal after modified to enhance their adsorption capacity, such as fly ash of coal-fired. Apart from specific surface area, element content, pore structure, and surface morphology of activated carbon have great effect on its adsorption ability. Compared to adsorbents without modification, active carbon impregnated with other elements, such as chlorine, sulfur, bromine and et al. had more excellent characteristics to remove specific pollutants."

Jan 1, 2011

By Guozhi Lyu, Ting-an ZHANG, Biyu Long, Yajing Tian, Xuejiao Cao, Weiguang Zhang

Aim to the separation problem of high concentration V–Fe in stronger acidic leaching solution of vanadium slag, a novel chelating extraction system is proposed to separate V and Fe. Influence factors including initial pH value, the extractant concentration, the phase ratio, temperature and time are investigated. The experiment results show that single extraction rate of V and Fe reach 85.57 and 0.39% respectively, when pH value is −0.4, organic phase composition is 30% Mextral 973H + 70% sulfonated kerosene oil, O:A = 1:1, stirring time is 10 min, extraction temperature is 30 °C. The industrial experiment results of three levels countercurrent extraction show that the total extraction rate of vanadium and iron can reach 97.44 and 0.23%, separation factor is 6410. The effective separation of V and Fe in high acid and high iron solution can be accomplished.

Mar 1, 2018

By Guy Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity' (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By Jerome P. Downey

The Indium Corporation of America - Colorado School of Mines Indium Separation Technology was evaluated as a potential means of treating smelter flue dusts stockpiled at the Pintlar Corporation property in Kellogg, Idaho. The patented technology represents a method for segregating the contained indium, lead, and other metals in forms acceptable for downstream processing and recovery. Separation is effected by treating the dust with metallic sodium in a bath of molten lead. Process effectiveness was measured by determining the relative distribution of key metals between the bullion and dross products at small pilot plant scale. The study indicated that application of the technology to the Pitlar samples results in a highly efficient concentration of lead in the bullion, while indium is collected in the dross. The distribution of other key metals between the bullion and dross products and the effect of varying selected process parameters are also discussed.

Jan 1, 1994

By José Roberto de Oliveira

In a smelting reduction process the reduction reaction occurs predominantly in the liquid state. The main reduction agent is the carbon from the carbon saturated iron bath. The aim of the present work was to determine the velocity equation and the rate constant of the reduction rate of MnO content in a Mn0-SiO2-Fe0 slag by iron saturated carbon and the carbon dissolution rate in a Fe-Mn bath. The manganese content in the iron bath was in the range of 5 to 15 wt.%. It was observed that the rates of carbon dissolution in all Fe-Mn baths are faster than the rates of MnO reduction by the carbon saturated liquid iron.

Jan 1, 1999

By A. V. Tarasov, V. M. Paretsky

"Based on theoretical and experimental studies into the specific features of the mechanism, kinetics, aerodynamics and heat transfer parameters of the flame-type oxidation of metal sulfides in a stream of technical-grade oxygen, a three-dimensional deterministic mathematical model of an oxygen-flame smelting furnace has been developed on the basis of the zonal method for computation of heat exchange. The model is presented in the form of equations taking into consideration the radiation component of the selective radiation, the convection component of mass transfer between the space and surface zones, heating of charge particles due to heat conductivity, accretions formation on a multi-layer refractory lining with inserted cooling elements. The adaptation of the model for a full-scale furnace has demonstrated the possibility for its use for computation of main smelting process parameters. Multifactor model investigations were conducted and the results obtained were applied using statistical methods for development of a simplified computational regression model describing the interrelation of the main output parameters: temperatures of flame, lining, slag and off-gas; heat fluxes to the lining; thickness of accretions; heat removed by cooling elements; copper content of matte. On the basis of this model, a block diagram of the algorithm was developed for control of the thermal conditions of the furnace, as well as the control algorithm itself.IntroductionThis paper presents the results of an integrated modeling and development of principles for control of copper smelting process using as an example the oxygen-flame smelting process (KFP) for treatment of sulfide concentrates at the Kovoguty Krompahy copper smelter (Slovakia) with a capacity of 20,000 tpy of copper."

Jan 1, 2001

By A. J. van der Zeeuw

The use of SME 529 in the extraction of copper from acidic liquors and of copper and nickel from ammoniacal solutions, is illustrated with results of laboratory and bench scale mixer/settler experiments. Special features of SME 529 are its high loading capacity and the ability to keep the complexes dissolved in the organic phase up to quite high concentrations.

Jan 1, 1976

By Denise Cristina de O. Nascimento

Natural lignocellulosic fibers are increasingly being used as polymeric matrix composite reinforcement owing to economical and environmental advantages as renewable and biodegradable materials. Among these, the piassava fiber extracted from a palm tree native of South America stands as one of the most rigid with a potential to be used as composite reinforcement. Therefore, the present work investigates the notch toughness behavior, by Izod impact tests, of epoxy composites reinforced with up to 40 % in volume of continuous and aligned piassava fibers. It was found that the incorporation of piassava fibers results in significant increase in the impact energy of the composite. Scanning electron microscopy analysis showed that the nature of the piassava fiber interface with the epoxy matrix is the major responsible for the superior toughness of the composite.

Jan 1, 2009

By Deng Ma

In order to obtain the solubility of carbon in vanadium-bearing hot metal, graphite powder is used for the carburization experiments. The other kinds of carburizers, namely low nitrogen carburizer, anthracite and coke are used for carburization of vanadium-bearing hot metal weighing 500 g at temperature of 1450, 1500 and 1550 °C respectively. Carbon increments of low nitrogen carburizer, anthracite and coke fall in descending order. It was found by comprehensive analysis that anthracite is the most cost-effective carburizer among three carburizers. Magnitude of apparent rate constant of carburization reactions is 10−4s−1. It is found that the carburization rate increase with temperature.

Mar 1, 2018

By Sedef Pinar Basag, Onuralp Yucel, Ahmet Turan

Niederschlag process is commonly used to produce metallic antimony. The process is a metallothermic process which is conducted in one step for metallic antimony production. Using this method Sb2S3 is mixed with coal and metallic iron and subjected to reduction. During heating, antimony sulfide is decomposed and sulphur combines with iron to form the matte phase. Metallic antimony is collected at the bottom of the crucible. In this study, evaluation of Sb2S3 concentrate, extracted and obtained from West Anatolian Region of Turkey was investigated by using Niederschlag process. The reductant stoichiometry, reduction temperature and duration were carried out in the experiments. Chemical analysis methods by using atomic absorption spectrometry (AAS) and X-ray diffraction spectrometry (XRD) techniques were used for the characterization of the concentrate, metallic nuggets and matte phases.

Jan 1, 2016

By D. I. Davidov, D. A. Shishkin, M. B. Rigmant, E. P. Romanov, N. N. Stepanova, N. V. Kazantseva

The Co-19 at.%Al-6 at.%W alloy was prepared by two methods of casting. We used arc melting under an argon atmosphere with casting into a copper water-cooled casting mold and induction melting furnace with casting into a ceramic Al2O3 mold. According to the X-ray and SEM analyses, phase compositions depend on the cooling rate of the ingot after melting. After arc melting, the cast alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co3W (DO19) type. After the induction melting, the alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co7W6 () type. All phases in the investigated ternary alloy at the room temperature are ferromagnetic. Curie temperatures of all obtained phases were defined. It is shown that the magnetic properties of the studied alloy are typical for soft magnetic materials.

Jan 1, 2015

By Chuanyu Feng

In this paper, a load-based micro-indentation technique suitable for field applications was developed. This technique bears the same theoretical background as traditional load-depth sensing indentation, and does not need any direct measurement of indentation depth or contact area. The removal of this requirement will reduce much of the cost associated with traditional instrumented indentation. To demonstrate the feasibility, a portable indentation system suitable for online material characterization was developed. Design issues of the portable unit were discussed and preliminary results using the portable unit were also presented.

Jan 1, 2009

By James P. Bennett

The successful reuse/recycling of refractory materials after removal from industrial service is limited because of contamination, the low value of spent materials, the low cost of virgin raw materials, the lack of driving forces such as regulations or taxes, and low disposal costs. Most spent refractory is disposed in landfills. Concerns over future liability for waste materials, corporate images, and IS0 14000 have helped to encourage recycling at some companies. The recycling practices and application for spent refractory materials at facilities successfully recycling used refractory materials will be discussed, with emphasis on similarities.

Jan 1, 2002

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016

By Joël P. T. Kapusta, Romeo U. Pagador, Noparut Wachgama, Chumnoom Khuankla

"Thai Copper Industries (TCI) is a custom copper smelter and refinery in Rayong, Thailand, with an annual capacity of 165,000 tons of cathodes. It employs the El Teniente Technology as the primary smelting reactor to produce white metal from copper concentrates. The white metal is further treated in Hoboken Siphon Converters to produce blister copper then refined in anode furnaces before being cast into anodes for electro-refining in the on-site tankhouse.Thai Copper Industries is the first copper smelter to install and successfully operate on a commercial scale with the Air Liquide Shrouded Injection (ALSI™) Technology in the Hokoben converters with sonic injection of oxygen enriched air and nitrogen for cooling of the injector tip areas. Following commissioning and the establishment of operating practices, the performance of the Hoboken converters with ALSI™ Technology produced outstanding results. The unique combination of an El Teniente and Hoboken siphon converters, both of which are bath smelting operations, offers very high blowing and oxygen efficiencies. As a consequence, reverts recycling was accelerated with minimal build up on the mouth, end-plates or even below the siphon that is typical in Hoboken converters.These outstanding results in the Hoboken Siphon Converters with ALSI™ Technology helped the TCI Plant reach a production of about 75% of its capacity within four months despite the fact that the TCI staff is quite young and its converter know-how and experience are not yet fully developed."

Jan 1, 2009