Search Documents

By R. Gerling

A computer program has been developed for finding a near-optimum schedule of the mining sequence for flat lying, tabular orebodies. The deposit is divided in blocks with equal areas and definite grades, thicknesses and ore contents. Mining is done by room and pillar method and trackless haulage to surface. Access from surface is by adits or ramps with additional vent raises. In total eight different general concepts for access and development can be realized. The optimum mining sequence is found by a heuristic method. Criterion is the maximization of the net present value over the lifetime of the mine. Specific stoping costs per t of ore are taken for con¬stant, whereas development and haulage costs for individual blocks and also sequences will be different. Correct ventilation and a technically sensible sequence are guaranteed. Beginning with a single block, neighbouring blocks are tested and an optimum stoping sequence is generated. The net present value of the total mining operation for the planning period is calculated, taking into account ore, which is mined during development. The program can also be used to investigate given mining sequences.

Jan 1, 1986

By S. P. Mehrotra, P. C. Kapur

A phase-species classification is suggested for the mathematical models of flotation kinetics. Important models are discussed and the structure of their rate constants and parameters is analyzed. Split or enhancement factors are formulated for different kinetic models. The steady state dynamics of the flotation circuits can always be described in terms of these factors. For simulation of circuits, feed is characterized in a formal manner starting from a multivariate distribution of particles in flotation rate, size and mineral content. Synthesis of optimum circuits which simultaneously searches for the best process variables and structural parameters from a generalized master network is described. Trends in the areas of search algorithms, role of middlings and feed identification etc. are indicated.

Jan 1, 1989

By Jon Holder, Brann Johnson

Pore-fluid/rock chemical interactions on both short and long time scales can produce significant pore structure and mineralic changes that can markedly alter transport properties, such as fluid permeability. The introduction of the chemical factor requires modification of experimental systems and methodologies developed for measurements in which chemical effects are minimal. Particular attention must be given to temperature effects, fluid chemistry, fluid/rock reactions and kinetics, fluid flow rate, and fluid/experimental-system reactions. The ability to obtain very low, steady flow rates at constant fluid pressure is important for study of some fluid/rock systems. Minimization of metal corrosion is of paramount importance and requires choice of proper metals, such as titanium, and certain Ti-alloys and Ni-alloys. In this paper, we briefly discuss the relevant chemical factors affecting system and experimental design. The primary focus, however, is on the characteristics of highly corrosion resistant metals, thermal and chemical resistant jacketing materials, and the attributes and limitations of various flow-rate and back-pressure control systems and flow-rate measurement systems.

Jan 1, 1986

By Yelloji M. K. Rao, P. Somasundaran

Reagents of biological origin are becoming more and more important in the field of metallurgy, especially in the areas of mineral processing and hydrometallurgy. The advantage of lower operating cost over physical and chemical processes and the capacity to operate with low grade ores make the microbial processes further attractive. In this paper, the role of microbes directly as a reagent and microbially produced reagents or secreted metabolites in mineral processing and hydrometallurgy will be discussed. Adhesion of microbes to surfaces is known to alter the hydrophobicity of minerals. Applications include surface modification to impart hydrophobicity or hydrophilicity on sulfide or non-sulfide minerals and dissolution of precious metals. Microbes can also perform the role of flocculating agents. Biosorption of toxic and heavy metal ions by microbes are finding application in treating tailing ponds. Mechanisms associated with the use for microbially produced reagents are discussed along with some recent results.

Jan 1, 1994

By Y. Kurokawa, R. Kurosawa, I. Iwata, I. Fukuoka, N. Sugita

INTRODUCTION The Ningyo-toge Mine is located in the western part of Honshu, about 800 km from Tokyo. Since the discovery of uranium ore deposit at Ningyo-toge in 1955, different kinds of mining and milling tests have been carried out. A new pilot plant of milling and UF6 conversion is also being under construction. Operations are scheduled to start by the end of this year. In 1979, the uranium enrichment pilot plant was constructed at Ningyo-toge and test operations have started. Thus, the Ningyo-toge area is assigned to undertake the Research and Development of the upstream of the nuclear fuel cycle in Japan. PNC has been strengthening its security measures more than ever. This paper will focus on the disposal of wasted material, especially on the disposal of heap leaching residue, in Japan. URANIUM ORE DEPOSITS The uranium of the Ningyo-toge Mine is characterized genetically by epigenetic sedimentary type deposits. They occur in the host rock of Neogene tertiary fluviatile conglomerates and sandstones which unconformably overlies the Mesozoic-Palaeogene granitic basement covered with lucustrine deposits and volcanic ejecta. More than 12 deposits have been found over the area of approximately 160 km2, and distribution of the deposits are strongly controlled by the so-called channel structure, probably remnants of paleo-streams on the denudation surface of the underlying grantic basement. Each ore body has different shape and dimension respectively, but about 2-3 meters thickness with the average grade of 0.05-0.2% U308 is common feature of the ore bodies. The ore is soft and loose, and it is composed of common rock forming minerals of allogenic origin and their altered products. The chemical composition of the ore depends on the constituents of the country rocks or the pebbles. A primary mineral, ningyoite and secondary mineral, autunite are major ore minerals, although three primary tetravalent minerals and thirteen secondary hexavalent minerals have also been detected. MINING EXPERIMENT Since 1959, various types of underground mining tests have been carried out at Ningyo-toge Mine. The room and pillar method was safe and simple, although the uranium ore recovery was below 70%. After experiment of the retreating long-wall method and slicing mining method, it was found that the modified long wall method was the most appropriate for the underground mining of the Ningyo-toge uranium deposits. This method was completed successfully to increase efficiency up to 2 or 3 times, as compared to conventional methods. MILLING EXPERIMENT In 1964, a small test mill was constructed at Ningyo-toge, and a milling experiment using the Ningyo-toge uranium ore was started. Re-modelling of equipments and improvement of the process lead to the establishment of the technique of the so-called wet process, and produce UF4 directly from the ore. The flow diagram is shown in Fig. 1.

Jan 1, 1981

By T. D. Rourke, E. J. Cording, O&apos

INTRODUCTION Detailed investigation of a 60-ft-deep excavation in a mixed profile of sands and stiff clay was performed by the University of Illinois for the Washington Metropolitan Area Transit Authority (METRO). The work was coordinated through DeLeuw, Cather and Co., the General Engineering Consultant of METRO. Instrumentation was concentrated in a portion of braced excavation for the Gallery Place Station near the intersection of 7th and G Street. The early construction date, the 60 ft depth of cut, and the proximity of large buildings formed the basis for selection of this site as the focal point of observation and measurement. A history of lateral and vertical displacement is provided wherein movements which occurred during excavation to the full depth of cut and, subsequently, during station construction and the removal of braces are described in detail. Observations of preloading and the consequent brace loads and wall displacements are described. The effect of temperature change on brace loads is discussed and the measured apparent earth pressure for the 60-ft cut is provided. The paper discusses the relationship of lateral displacements of the cut wall to the construction procedure, and compares the lateral wall displacement with both lateral and vertical movement in the surrounding soil mass. Based on observed movement, the method by which displacement was predicted for a nearby 82-ft-deep excavation is described. The performance of the 82-ft-deep excavation has been summarized elsewhere (2).

Jan 1, 1974

By Oscar Letelier Gonzalez

The goal of mine planning is to determine "the best" strategy to exploit an ore deposit during its workable life. Such strategy must be consistent with the objectives of the company and must be subject to the contraints imposed by economical, physical and geological conditions. Mine planning process may be broken down into three categories, according to the planning horizon: Long range, Short range and Operational. The shorter the scope of planning, the higher the level of details and the lower the degree of freedom associated to each plan. A long range plan defines the economic limit of mining at the mining life end of the deposit; it also can be used as an aid in the evaluation of the economical potential of a mineral deposit and as a guide for short range plans.

Jan 1, 1979

By Ebrahim Tarshizi, Livernois Ryan, Emily Sarver, Zoe Scopa, Robert Setterlind, Leah Frost

"The mines of the future present a host of challenges, which may appear exciting or daunting, depending on one’s perspective. Whether some sectors of the public recognize it or not, the demand for raw resources is not going away any time soon. In fact, it is rising, as the global population grows, urbanizes and attempts to steadily increase quality of life. Yet, at the same time that much of the highly developed world is calling for greener goods, reduced consumption and cleaner production, in other areas there are cries for clean water and sanitation, consistent energy supply, access to health care and education, personal security and support for basic human rights. The balancing act for sustainable development of our global society is, indeed, precarious and the mining community is a key player. Fortunately, many industry members have accepted this role and the responsibility to provide leadership and a solid foundation for progress. Looking ahead, we need new generations of leaders, including many mine engineers who are ready to tackle all sorts of complex problems.There are tremendous needs just for technological innovations. Increasingly tough deposits will require that the industry continues to expand scale toward “mega pits” and “super caves;” fully develop unconventional recovery techniques like in situ leaching and gasification or deep-sea extraction and seriously consider off-earth endeavors. Such work will take entirely autonomous equipment, novel separations, processing and recycling methods, and systems that can withstand extreme physical conditions, just to name a few. It will also take a level of systems integration never-before seen in the mining industry, complete with big data issues, sophisticated predecitve analytics and modeling efforts and cyber-security challenges.Moreover, increasingly complex environmental problems will require creative solutions. Addressing issues like pollution control across multiple media, emerging contaminants, optimal management of wastes, selective mining and shared use of resources between mine operations and surrounding communities and ecosystems are among the top priorities. Really, a complete paradigm shift must occur, such that the focus is on overall improvement of environmental conditions, rather than minimization of impacts. A similar shift will be required in the social realm. How can miners be safer and healthier on-site and off? How can the industry contribute to communities such that they are better off, now and longterm, for having a mine next door? How can artisanal mining practices be transformed to also contribute to sustainable development? How can the industry’s work be a factor in increasing economic and political stability? How can the public understanding of raw resources and the need for mining enterprises be improved?Given the coming challenges, there is no doubt that the mine engineers of the future will need highly diverse skillsets — meshing traditional and contemporary competencies to a degree not previously considered in mining, or most others fields. To be sure, the scope and scale of mining projects make them wholly different than most other engineering work, aside from perhaps the largest civil and urban development projects. While on-the-job experience will continue to be essential, formal education programs (i.e., at post-secondary institutions) must lay critical groundwork."

Jan 6, 2017

By Greg Bold, Mahmood Khwaja, Yuannian (Jerry) Wan, Michael S. Schultz, William Simcoe

Beaver Creek Clean River Project will satisfy the consent decree requirements by capturing and treating combined sewage overflows. The project consists of, approximately, 2,700 feet of 30-inch trenchless pipe installation, a new screening/disinfecting facility, an expansion of an existing diversion structure, and a 72-inch internal diameter, 530-foot long mined tunnel. The tunnel portions are being progressed as early release packages. This paper presents the geotechnical exploration program and the subsurface conditions encountered; interpretation of the geotechnical conditions; and, approach to developing stand-alone packages for the tunnels to mitigate construction and schedule risks and continue to advance the project.

Jun 13, 2021

By K. S. Narasimhan, T. C. Rao, R. Bhima Rao

Investigations have been carried out to evolve a grinding aid useful in grinding a 40% iron-bearing magnetite containing quartz as the major gangue, based on studies conducted with pure magnetite, pure quartz and its synthetic mixture. These investigations established that an addition of 200 g of CaO per metric ton of ore was the most effective in grinding quartz preferentially over magnetite at 75% solids concentration by weight. The limited rheological studies conducted suggest that the effect could either be due to dispersion or the structural modification of quartz. More importantly, a new concept, that of Critical Solids Concentration, where two different minerals behave like one with respect to response to communication in a tumbling mill, has been introduced for the, first time. Above this concentration, one of the minerals is ground at a faster rate than the other, whereas the reverse is the case below this concentration.

Jan 1, 1992

By Y. C. Kim, W. L. Meyer, W. Cai

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the US has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms. This paper compares the performance of the floating cone algorithm with the rigorous optimization algorithm of the Lerchs-Grossman's graph theory and the newly developed maximum network flow algorithm by Hanson (1986). The maximum flow algorithm is a modified version of the logic as initially advocated by Johnson in 1968. Comparisons are made for three different deposits in terms of the total profits generated and the computation times involved. The results of the comparison show that both algorithms produced higher total profitability pits than the floating cone in all three deposits, although the increase in profits never exceeded 1 % of the base design obtained using the floating cone. Between the graph theory and maximum flow, graph theory produced consistently higher profits. The current version of maximum flow, however, cannot be modified to produce the optimum pit. Nevertheless, the authors prefer the maximum flow over the graph theory, simply because it is easy to program as well as to explain.

Jan 1, 1987

By Kal V. S. Sastry, Stephen N. Little

Computer simulation of comminution systems is found to provide significant cost savings by enabling efficient circuit design and development of control systems. These simulation systems are based on sound mathematical models and numerical methods. Nevertheless, they are found to be hard-to-use and hard-to-modify to carry out more elaborate process analysis. This paper discusses the fundamental principles and practical aspects of an advanced, highly functional, and user-friendly SIMulator for COMminution, SIMCOM, that is being developed at Berkeley by incorporating state-of-the-art software engineering principles.

Jan 1, 1992

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994

By D. U. Deere, T. R. Harrell

Factors such as rock cover, rock type and rock quality can exert a dominate influence on the behavior of a concrete tunnel lining. This paper will present and discuss the investigation, evaluation and use of such factors at the Rocky Mountain Pumped Storage Project in the design of the 10.67m (35 foot) diameter concrete tunnel lining. A plane strain, finite element analysis was performed on the concrete/rock system. The finite element model consisted of a concrete lining zone and three (3) rock zones; a highly destressed rock zone, a transitional rock zone and an intact rock zone. Zones were differentiated from one another by varying the modulus for each zone. Results of this study yielded a concrete lining strain from radial expansion which was used in the crack control calculations for the concrete tunnel lining. After the tunnel excavation was performed, plate jacking tests and additional seismic surveys were run on the tunnel walls. This testing served to confirm the rock modulus values used in the preliminary analysis. However, results were observed which indicated that a two zone rock model would more accurately represent in-situ rock conditions than the three-zone rock model used in the preliminary analysis. This revision to the concrete/rock model was made and a final concrete tunnel lining analysis was performed.

Jan 1, 1986

By Robert A. Haney

During the last ten years, longwall mining systems have undergone many changes. Panel widths and lengths have increased. Longwall faces have become more automated. Average production from individual longwall panels has increased from 1,000 to 3,600 tons per shift. To control the dust generation resulting from the higher production, longwall dust control systems have integrated various dust control techniques. Systems designed to control dust generated at the crusher/stageloader, shearer, and supports are common to most longwall faces. A survey was made of the dust controls that are currently in place on all the longwalls in the U.S. This survey addressed the types of controls used to reduce dust generated at the crusher/stageloader, shearer and roof support movement. Additionally, information on face ventilation rates, cutting cycle and level of automation was obtained. The purpose of this paper is to review the dust control practices that have been implemented throughout the United States and to identify those controls that are being used on high production longwall faces. Additionally, a model is used to demonstrate how ventilation and automation affect occupational exposure. Automation of roof support movement can offer some of the greatest reductions in occupational dust exposures. While technically feasible, its full benefit has not been fully realized by the industry. Until technology to fully automate longwall mining systems becomes more reliable, future dust control systems must rely on increased ventilation, application of headgate dust collectors, improved shearer dust controls and improved shield dust suppression systems.

Jan 1, 1995

By W. E. L. Minter

The most important witwatersrand gold placers occur on extensive unconformity paleosurfaces that were produced during protracted periods of fluvial degradation. The erosional etches on what was generally unlithified substrate indicate that low sinuosity erosion patterns prevailed. The transport systems were dominantly braided fluvial with a minor debris-flow component. The placer sediments were non-cohesive sands and gravels which were evidently transported by fluctuating, yet perennial, discharges across extensive, low relief, bra1dplains, not far from littoral environments. Progress made in understanding heavy-mineral transport processes now emphasizes the importance that selective entrainment probably had in producing concentrations. Cognizance that these characteristics are not unique to the Witwatersrand should be taken into account when designing exploration models.

Jan 1, 1988

By Simon D. Handelsman

Technical co-operation activities of the Department of Technical Co-operation for Development of the United Nations Secretariat have included the introduction of electronic data processing techniques in mineral sector projects for several years; computers have been provided to countries in Africa, Asia and Latin America. Advisory services are provided to interested developing countries at their request concerning applications for various uses in mineral sector activities. They include advice on appropriate hardware and software depending upon the requirements of the particular Government. The Department's activities in this area are described. The input from a Group of Experts on this subject convened by the United Nations, and their conclusions and recommendations, are also discussed.

Jan 1, 1986

By Duk-Won Park

A new gage for monitoring fractures in underground openings was successfully developed utilizing the reflection photo-elastic technique. The gage may be used to detect crack initiation in mine openings or tunnels so that remedial action may be taken to prevent further deterioration. Fringes concentrated around the cracks were spread by the use of rubber backing. Crack growth as little as 0.003 inch up to as much as 0.1 inch width were detected in this study. Variation of gage materials will provide alternative ranges. The feasibility of the method was tested and calibration was made in the laboratory study. Field study successfully demonstrated the capability of applications in detecting mine roof crack development.

Jan 1, 1982

By N. Parra, M. N. Herrera, T. Vargas, C. González, B. Escobar

The bioleaching of mineral sulfide pulps in a bench-scale rotating-drum reactor was studied. The reactor contained horizontal paddles on the inner wall for lifting the mineral pulp. The performance of the reactor was tested by bioleaching a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans (ATCC 19859). The concentrate was efficiently bioleached at a 50% pulp density with the drum operating at from 0.5 to 1.0 rpm. Attempts at bioleaching the concentrate at the same pulp density used in a conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows the process to operate at much higher pulp densities than conventional stirred-tank reactors. This results in improved bacterial activity because of better attrition control of the mineral particles.

Jan 1, 1999

By Kevin Lundberg, Philip Sander, Daniel Weinberger, John Reilly

Since the early days of risk management, developments in technology and guidelines (ITA, ITIG, OGG, UCA) have advanced risk management and probable cost estimating, which are now widely recognized. WSDOT’s CEVP risk-based cost validation process is now established after 20 years. This paper traces these developments, summarizes advanced techniques, and presents examples of US and international projects with results. A particular case of using advanced risk evaluation to allow enhanced-capability TBMs to be considered in a competitive bid process is presented. Further advances, including the use of digital twin risk-based representation of complex projects, are described.

Jun 13, 2023