Search Documents

By William S. Gilmer

INTRODUCTION As man moved through the ages into the era of metals, he became increas¬ingly dependent on the extraction and beneficiation of various ore types. His progression has required more material, new sources, and inevitably, a need to extract the values from ores of much lower yield. Inherently welded to this need to extract has been the attendant requisite of power and water to carry out these tasks. With the richness of these deposits diminished, and the in¬crease of demand, mining has become so intimately tied with the needs of these auxiliary systems that the modern day milling operation can ill afford to ignore them. In the times of Agricola 16th century methods of milling required little thought for power or water consumption. Reduction was accomplished by hand¬sorting and hammer and grinding done with stamps and millstones. Medieval concentration was carried out by the "Jigging sieve" with agitation supplied by the sleeveless arm of the operator (The Mines Magazine,_ March 1933). Little consideration was likely given to the power source unless it became apparent that he had insufficient means to meet the demands of a dawn to dusk operation. Fuel for power production was also probably of little consequence unless sustained drought or warring neighbors burned the miners fields. Water was available from any adjacent stream with recycle, potable, tailings and mill consumption all going and coming from the same source. By the end of the 18th century and the early 19th century the requirements of larger throughputs and better re¬covery were forcing the miner to the need for greater sources of power and water. Arrastras, capable of accepting several hundred pounds of charge, con¬sisted of a clay bottom, a "liner of rocks harder than the substance to be crushed" and a revolving center post in which the ore was ground and amalga¬mated. Used in conjunction with a slucing system, this formed the primary recovery method of the time. Power was supplied by horse or oxen or, if terrain was amenable, by use of a horizontal or overshot water wheel. A typical system required 4.5 kw (6 hp) and needed to run in the vicinity of 15 rpm (Pre¬ston, 1895).

Jan 1, 1986

By H. F. Hennigar, D. L. Pawson, E. J. Foell

Results of an analysis of abyssal benthic megafauna based upon review of nearly 250 hours of videotape and 2149 bottom photographs are presented, and the utility and limitations of such analyses in deep sea biological studies are discussed. The images were acquired at depths of 4400-4800 m during a resource assessment cruise aboard the RV Prospector using a unique, deep-towed, television telemetry system coupled with 35-mm photography. The data review was carried out in support of NOAA efforts to provide adequate environmental baseline information before industrial exploitation of nodule deposits and concurrent monitoring begin.

Jan 1, 1991

By W. R. SHAHAN, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation on the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). 

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999

By D. Newman

"The U.S. stone industry is in a transition from surface quarries to single and multiple level underground stone mines. The factors driving this transition include surface quarries; ? reaching their economic stripping ratio, ? encroaching on the mineral reserve boundary where the remaining reserves are below the active pit, ? dust, noise, and blast vibration concerns as suburban neighborhoods and development move into formerly rural areas. Ground control is critical to the success of a safe and productive, mining operation. The primary focus of the ground control engineer in an underground stone mine is the stability of the roof or back, development and benched pillar stability, stability of the sill pillar between vertically adjacent mining levels, and floor stability. Roof stability begins with the selection of a stable back horizon based upon the presence of a thin shale parting, stylolite, or other discontinuities from which the production shot can easily ""peel"" away leaving a stable back stratum. Room width and the decision of whether to bolt the roof, the bolt length, bolt type, bolt diameter, and spacing of the support is controlled by the thickness, fracture spacing, jointing, and material properties of the back strata. Horizontal stress controls the header and crosscut azimuth as to avoid driving perpendicular to the maximum horizontal stress direction. Stable pillar dimensions depend upon the interaction of the; ? vertical stress resulting from overburden thickness and multiple level interaction of overlying level(s), ? mining height during development and the final mining height after floor shots are taken while benching, ? presence of faults, folds, or joints passing through the pillar, and ? stone lithology recognizing that the presence of oolitic bands, shale partings, and bentonite beds create zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture sensitive strata, weak stone bands, or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. The ground control issues for underground stone mines are most clearly presented through a series of case histories. The case histories presented in this paper are a mix of ground failures and successful mining. The focus is on the geotechnical data required for underground stone mine ground control for roof, pillar, and floor design and stability analysis."

Jan 1, 2016

By R. Benito, J. Lopez, H. Gamarra

This article describes three practical applications of the Hill of Value (HoV) methodology within different stages of strategic planning for open-pit mining operations and projects. In the pursuit of optimal mine planning, this study establishes a comprehensive case study during the (i)design phase, by refining key parameters for efficient decisionmaking. (ii)production planning, where the HoV is used to define achievable production rates, enhancing operational effectiveness through a nuanced consideration of mining and processing capacities. (iii)Additionally, the study introduces a conceptual framework for orchestrating the optimal sequence of multiple pits during the planning phase, with a focus on maximizing project value.

Feb 1, 2024

By John C. Schneider

During the past decade, operators and researchers have worked toward a better understanding of the mechanisms operating in flotation. As reported by W. J. Trahar in 1981, this work commenced with the operators determining a relationship between recovery and particle size. They defined three particle size ranges, that being fine, intermediate and coarse. It was noted that the fine and the coarse ranges had slower flotation rates than the intermediate range as demonstrated by their lower recoveries.

Jan 1, 1998

By Carl E. Williams

Several years ago it was decided that ASARCO was in need of a good mine scheduling program to complete the computerized open pit mine planning package that was being used on new prospects and operating properties. A trial and error approach was being used to schedule a mine on a year by year basis, but this was time-consuming and far from offering an optimum solution l. Due to the magnitude of time and expertise required to develop such a sophisticated computer program, it was decided to search outside of the company for one already developed and available for purchase, This proved fruitless and therefore proposals were requested from consulting firms that had the expertise to develop such a program. Out of the five firms that submitted proposals, the one chosen was Systems Control, Inc., (S.C.I.) of Palo Alto, California. S.C.I. was selected because it was felt that they offered the greatest capability in the mathematical solution of complex problems. But due to their lack of mining expertise, a cooperative venture was developed whereby ASARCO would supply this mining knowledge. The selection of this vendor, the formulation of the contract and specifications, and the development of the computer program required about 3 years to accomplish.

Jan 1, 1973

By Pentti Seppanen

The activities of Outokumpu Oy in the mining industry span all branches from prospecting to the production of refined metals and the manufacture of semifinished products. Products include copper, zinc, mercury, cadmium, nickel, cobalt, sulfur, gold, silver, iron ore, stainless steel, selenium, ferrochromium, lead and chromium concentrates, as well as chromite foundry sand. In addition, the activities of Outokumpu Oy extend to development and production of instruments, planning of industrial projects and instrumentation as well as the manufacture of specialized machines for ore concentration. The company now operates ten mines, eight of which are underground and all of which are in sulfide deposits except one. The fully automated monitoring and control of underground mine ventilation at the Pyhasalmi mine are an important technological contribution to the industry. Development work on the ventilation control was started in 1969, and since May 1973 it has operated in a fully automated computer-controlled mode. The Pyhasalmi mine has been in production since 1962, having begun as an open-pit operation. Development of underground mining began in 1967. The present annual production is one million tons all from underground mining. The underground mine is equipped with a main shaft and an auxiliary shaft, and two raises for ventilation. There is also a rampway from the surface to a depth of 500 m. The main shaft is for ore hoisting and the auxiliary shaft is used for waste-rock hoisting and for downcast ventilation. One of the raises is for downcast ventilation and the other is for upcast ventilation. The mining methods employed at Pyhasalmi are sublevel stoping with backfill, sublevel caving, and sublevel shrinkage stoping. Copper and zinc concentrates are produced. The Pyhasalmi mine is highly mechanized with about 4000 installed diesel horsepower underground. The maximum capacity of fresh air is 150 m3/s.

Jan 1, 1979

By Bruno Mattle, Max John

For tunnels with low overburden, the shotcrete lining is the main element of ground support, which is why shotcrete behavior is of prime importance. Following its application, shotcrete not only gains strength and stiffness with time but—if loaded at an early stage—it is also subject to creep which in turn leads to stress relaxation. For two-dimensional FE calculations, a computational modulus of elasticity of shotcrete is to be used. Based on parameter studies it was found that the modulus of elasticity of shotcrete depends on both shotcrete mix and ground behavior. While the Young’s Modulus used for young shotcrete may range from 1,000 to 7,000 MPa, the Young’s Modulus used for hardened shotcrete is best represented by a value of 15,000 MPa.

Jan 1, 2003

By David Beck

In Australia, Safe Work legislation requires mines to have a documented ‘Safety Case’ explaining how a mine will safely manage all major hazards. A similar requirement is legislated or inferred by regulation in all jurisdictions. For small scale, instabilities leading to day-to-day seismic hazards, a ‘Stability Safety Case’ built around observational methods and measurement triggered responses can be effective because adverse situations are easily identified and the costs of lower control measures are not onerous. Also, if the influence of a volume of yield on the mine load system is small, the response of the system will be more predictable. However, for episodes of large scale mine instability, the hazard derives from the widespread, multi component influence of the event on the mine load system. As the system response depends on interactions between many parts, the resolution of predictions will be lower and situations can arise without local precedent. Further, as episodes of large scale instability change the stiffness and nature of the connectedness between parts of the mine load system, the behavior of the system before the event will be a poor empirical basis for forecasts of event related hazards. Most importantly, Triggered Action Response Plans (TARPs) and ‘traffic light’ warning systems cannot make design choices or identify new hazard phenomena. They are ‘lower’ control measures targeting explicit human-made instability hypotheses. As such, the Safety Cases related to management of hazard from potential large scale seismic events and mine instability cannot rely solely on TARPs. Mines that successfully manage meaningful dynamic instability always acknowledge the ultimate reliance on expert human intuition, knowledge and imagination to appreciate the range of possible hazard scenarios, to make stability hypotheses and propose solutions. Complex analysis, TARPs and measurements are critical steps in the human decision cycle, but only support the making and testing of ‘Stability Hypotheses’ made by expert engineers. Relying on expert skill and judgement as essential components of a Safety Case, however essential, introduces human vulnerabilities. Another challenge is that the expert decision making process is hard to document. Beck et al 2019 first described an organizational and procedural framework for maintenance of an ongoing large-scale ‘Stability Safety Case' where a degree of expert judgement and imagination is needed to manage a seismically active mine. The structured data appreciation process outlined sufficient measurements, analysis and appreciation to confirm the stability state of the mine and was applicable to all underground mines. After several years of implementation in various forms in stoping, caving and room and pillar mines, this update addresses lessons learned and describes some considerations for numerical forecasting to establish a base case, and some challenges for empirical hazard identification.

Apr 26, 2022

By Paul H. Miller

After passage by the Congress, Public Law 95-87, the "Surface Mining Control and Reclamation Act of 1977" was signed by President Carter on August 3, 1977. This law, in its simplest form, was intended to control the environmental effects of surface coal mining and to ensure that mined land is restored to a condition equivalent to that prior to mining. Immediately after the signing, the wheels of government bureaucracy began turning to establish a new federal agency -the Office of Surface Mining Reclamation and Enforcement or OSM -in the Interior Department that would implement the provisions of the Act. Since this took time and because the Congress had not yet provided funding for OSM, a special task force was assembled within the Interior Department to begin the task of writing interim regulations to implement the Act. With respect to the use of explosives, the Act specified that a blasting plan be included in the application for a mining permit. The blasting plan will outline the procedures an operator will use to meet specified environmental protection performance standards. The performance standards established by the Act require explosives to be used only in accordance with existing state and federal laws and regulations and with regulations to be promulgated by the regulatory authority. The regulatory authority was defined as either a state agency operating under an approved state program or the OSM operating under a federal program. As a minimum, it was specified that the regulations should include provisions to require that: 1) a blasting schedule be published in a local newspaper and be mailed to local governments and to all residents living within 1/2 mile of the blasting site . 2) daily notice be given to residents in the area prior to blasting. 3) blast reports be prepared that are maintained for three years and available on request to the public. 4) blasts be designed to prevent injury to persons, damage to property outside the permit area, adverse impacts on underground mines and adverse effects on ground or surface water channels or availability outside the permit area. 5) upon request of residents or property owners within 1/2 mile of the permit area, preblast surveys shall

Jan 1, 1978

By R. Shields

"Hard rock mines move large volumes of material. But the conveyors essential to this movement suffer lots of problems, including carryback, spillage, dust, and belt wander. Many of these issues are created at the transfer points where the belts are loaded. This presentation will start with an overview of the latest transfer point systems that incorporate safety and serviceability by design. It will then report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, Nevada. Here performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine. THE IMPORTANCE OF TRANSFER POINTS Conveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance are the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created. The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material—cargo released in the form of carryback, spillage, or airborne dust—that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems, and issues with community relations. As estimate attributed to the U.S. Mine Safety and Health Administration (MSHA) notes that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points. TECHNOLOGIES TO IMPROVE TRANSFER POINTS A number of techniques to improve the performance of conveyor transfer points have been developed. They include: • Absorbing impact, to prevent damage to belt, belt support systems, and conveyor structure, and reduce spillage caused by the impact energy arising from long material drops or large lumps of material loaded onto the receiving belt. • Stabilizing the belt line, to eliminate sag that allows spillage and encourages material entrapment that can damage the belt. • Protecting the skirtboard seals, by sheltering the sealing strips from the mass of cargo pushing material toward the edges of the belt. • Using self-adjusting, multiple-barrier edge seals, to keep material on the belt by providing long-lived seal efficiency with minimum maintenance requirements. • Controlling and centering the belt’s path, to eliminate belt wander and the spillage and damage it can cause. • Allowing dust to settle, through the incorporation of chutework that provides expanded stilling zone and the use of dust curtains at the points where the belt enters and exits the transfer. • Adding supplemental dust control systems, through the installation of systems for passive dust gathering, water-based dust suppression, and/or active dust collection."

Jan 1, 2017

By D. L. McClure

Gold mineralization at the Colosseum Mine is submicroscopic and associated with pyrite. Pyrite occurs in breccia clasts, replacing dolomite, in crackle breccia veinlets with traces of quartz, and as disseminations in two small, interconnected intrusive pipe complexes of rhyolitic felsite and breccias of felsite and wall/country rock. Breccia types grade from felsite plus wall rock of Pre-cambrian gneiss to cross-cutting breccias "of felsite, gneiss, and Paleozoic sedimentary rocks that are in contact with the Precambrian gneiss terrane one-quarter mile (40Om) southwest of the Colosseum pipes. Mineable reserves are estimated to be 8 million short tons (7.3 million metric tons) at 0.074 troy ounces of gold per short ton (2.3 g/metric ton) at a cutoff of 0.03 troy ounces of gold per short ton (1.0 g/metric ton).

Jan 1, 1988

By R. Chandramohan, Landon Jackson, C. Meinke

Understanding constraints within the raw battery material supply chain is essential for making informed decisions that will ensure the battery industry’s future success. The primary limiting factor for long-term mass production of batteries is mineral extraction constraints. These constraints are highlighted in a first fill analysis which showed significant risks if lithium-ion batteries are used to fully support vehicle electrification and intermittent energy storage. Nickel, lithium, cobalt and graphite reserves risk 100 percent depletion with significant consumption of known resources. Furthermore, more than 700 new critical mineral mines will need to be developed to meet the required production rates for decarbonization by 2050. Demand for critical minerals will outpace mine development timelines even as improvements are made to battery energy density and compositions. Governments and the private sector need to align themselves on decarbonization goals to establish cooperative agreements on the critical mineral supply chain by reducing the barriers to entry and increasing exploration efforts. Additional measures must also be taken to reduce the demand for critical minerals. Policy such as incentivizing public transportation and biking infrastructure can be exploited to drastically reduce the mineral demand placed on the mining industry.

Feb 1, 2025

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By Mohamed Gamal, Bill Zietlow

"In oil fields that have been depleted with conventional surface oil wells but still contain significant reserves, an extraction alternative that has been constructed recently consists of a drilling gallery below the oil-bearing formation at the bottom of a 1,200-ft deep shaft where upward sloping wells are being drilled to allow oil collection by gravity. The gallery is 92-ft diameter with a flat ceiling supported by rock bolts and shotcrete structurally connected to the shaft liner, which doubles as a large tension support element. A special excavation sequence was implemented for the gallery to maximize arching in the stress above the large diameter gallery. The gallery was located in competent sandstone, constructed with sequential excavation methods, and designed with a 3D finite element model. Special consideration was given to optimizing the gallery location to take advantage of the geology for construction and support while giving good positioning to the well drilling equipment. BACKGROUND Brierley Associates was contracted to provide both design and construction management services for an approximately 1,165-ft deep, 18-ft excavated diameter vertical shaft that opens to a 92-ft diameter flat roof gallery. The geotechnical data for the site was based on information available from literature and from data obtained during core drilling and from in-situ testing in a 1250-ft deep borehole. Wire line coring was conducted using a HQ, 10-ft long core barrel with a mud-rotary drilling method through sedimentary bedrock. The geometry of the shaft and the bottom gallery is shown in Figure 1(a). GEOLOGIC SETTING AND STRUCTURAL GEOLOGY The stratigraphy at the site includes a series of interbedded marine limestone, shale, claystone, siltstone, sandstone, and chert units. Limestone and shale are the predominant lithologies in the upper approximately 675 ft, while the lower portion contains five distinct sandstone units and more abundant shale, claystone, siltstone, and coal than the upper zone. A cherty sandstone at a depth of 1,130 below ground surface (bgs) was encountered. At a depth of about 1,000 ft to 1,116 ft bgs, a non-marine sandstone unit was encountered. This sandstone is the hydrocarbon bearing layer. Joints and fractures observed in the limestone had dips ranging from 0 to 90 deg. from horizontal with joint and fracture surfaces that ranged from planar to irregular and smooth to rough. Several, near vertical shear planes with slickensides were observed with surfaces that were generally smooth and planar. RQD values for the limestone ranged from 0 to 100 percent but in general were good to excellent."

Jan 1, 2016

By J. B. Hiskey

INTRODUCTION The extraction of gold and silver from ores, concentrates, and various metallurgical products can be achieved by a number of hydrometallurgical techniques. The solvation properties of alkali cyanide solutions on gold and silver were recognized 200 years ago. A cyanidation process for leaching gold from its ore was patented in 1887 and 1889 by MacArthur and Forrest. The solvent action of thiosulfate on gold and silver was observed over 100 years ago. Recently, several patents have been issued for processes using ammonium thiosulfate as lixiviant for precious metals, Berezowsky, et. al (1978) and Kerley (1981). Tozawa and and coworkers also examined the dissolution of gold in ammoniacal thiosulfate solution. Thiourea leaching of gold and silver initially discussed by Plaksin and Kozhukhova in 1941 but has received only limited attention since that early work. Use of thiourea as an alternative to cyanide was the topic of several papers presented at the 1981 AIME annual meeting In Chicago, Illinois. Hiskey provided a review of the fundamental chemistry of the dissolution of gold and silver in acidic thiourea solutions. Pyper and Hendrix reported on the leaching of a finely disseminated gold ore using thiourea as a lixiviant. The review article(6) previously presented was fairly comprehensive covering Important contributions to the chemistry of thiourea and the processing of gold and silver with acidic thiourea solutions. A search of the technical literature was made to determine recent (since 1981) progress and developments in applying thiourea to the processing of gold and silver. This review reveals that Soviet and Eastern European scientists are continuing to make major contributions to our understanding of thiourea/precious metal systems.

Jan 1, 1984

By Matthew Preedy, Anthony Pooley, Mike Wongkaew, Dirk Bakker, Raghu Bhargava

Sound Transit’s ST3 program will add 62 miles of light rail to the Puget Sound area, including connections to the neighborhoods of West Seattle and Ballard. These connections include considerations for both elevated and tunnel alternatives in West Seattle and Ballard, as well as a new tunnel and six underground stations in the densely developed downtown Seattle. This paper describes the conditions and constraints along the corridor, and the latest development in the ongoing process to plan the underground guideways and stations.

Jun 13, 2023

By M. D. Martin

Low metal prices and increasingly stringent environmental regulations, coupled with the threat of higher governmental royalties are adversely affecting both existing and new operations. Existing operations must therefore be run at maximum operating efficiencies to enable mining companies to survive and grow. Well planned and executed "outsider" reviews can help achieve this goal. Many mine managers and those who direct them resist the idea of "outsider" reviews for a variety of reasons, some valid and some not. Those managers who do bring in the "outsiders" are nearly unanimous in reporting that the exercise in self-discipline was well worth the pain and effort and repaid the cost many times over. This paper makes a strong case for "outsider" reviews and gives recommendations on the kinds of reviews to undertake. The authors draw upon their nearly 70 years combined experience, much of which has been in operations.

Jan 1, 1994