Search Documents

By Keiichi Fujita, Katsumoto Ueda, Hiroshi Nakauchi, Naohiko Okumura

INTRODUCTION This paper presents (1) modified slipform system which was employed for simultaneous concrete placement for permanent lining and Instruction of a partition wall in the execution of a ventilation shaft 620m deep, and (2) current shaft sinking techniques which have been applicable and efficient for the subsurface conditions in Japan. MODIFIED SLIPFORM SYSTEM FOR PERMANENT LINING OF VERTICAL SHAFT General Information This paragraph deals with rapid construction by using modified slipform system for the permanent concrete lining and a partition wall of ventilation shaft, which has inside diameter of 620m and depth of 620m, of Enasan Highway Tunnel. The general feature of the shaft is illustrated in Fig. 1 and standard section of the shaft is illustrated in Fig. 2. The geological condition surrounding the shaft is mainly of ryolite and surface is of talus, but as a whole, they are rather weak and weathered rocks with faults, fissures and clay seams. 220mm borehole for the geological investigation was used as a drainage hole, predicting the amount of water inflow into the shaft to be 10t/min. The shaft was executed mainly by means of the conventional short step sinking method of 1.2m lift, employing temporary headframe and hoists. For each lift, 40 to 50cm thick temporary concrete lining was used. About 28,600m3 of rocks were excavated and

Jan 1, 1979

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By Biswajit Samanta, Pranjal Pathak

This article presents a customized genetic algorithms (GA) with new crossover and mutation operators to solve the short-term production scheduling problem of multi-mine mineral value chains (MVC). The preceding problem consists of determining the extraction sequence and destination allocation of blocks from all the mines collaboratively while closely meeting the quality and quantity requirements of the processing units subject to relevant technical and operational constraints. The short-term production scheduling is carried out at shorter scales wherein the operations are modeled in a great detail with large number of constraints. This makes the industry-scale instances of the problem computationally intractable for standard mixed-integer programming (MIP) solvers. Thus, a GA-based heuristic approach is developed to obtain nearoptimal solutions to the large-scale instances of the problem in a reasonable amount of computational time. Computational experiments show that the developed GA-based method is a promising way to handle industry-scale instances of the problem. Moreover, the sensitivity analysis on various parameter combinations of crossover and mutation operators indicates that the customized global mutation operator, when used in combination with the customized crossover operators, took on average 12.5% less time than the customized local mutation operator to converge to a solution.

May 21, 2022

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By Barry Hunsaker

I cannot help but be reminded, as I stand here today, of my boyhood years and heritage, both of which are inextricably tied to this very valley and are, in a: bay, apropos of the theme of this Keynote Session. I remember the scarcity of people. For example, 48, 000 in Phoenix and 436, 000 in the State in 1930 and 65,000 in Phoenix and 499, 000 in the State in 1940. Today Phoenix boasts a population of over 500, 000 and the State a population of 1, 500,000. I remember the' lack of facilities, goods and services, including gas and electric power. I recall stories of my grandfather who had the freighting or teaming contract to haul all the supplies and generating equipment, by wagon mind you, up the old Apache Trail to Roosevelt Dam. . .a three day trip from the nearest railhead which, by the way, was not Phoenix, for it did not merit a railhead on those days, but the village of Maricopa approximately 25 miles south of Phoenix. I remember chopping firewood, heating wash water on an open fire in a No. 3 wash tub at the rear of the house and doing my school homework by the light of a kerosene lamp just 25 to 35 years ago within what is now a large metropolitan area

Jan 1, 1965

By Lake H. E.

The request to participate on your theme panel was accepted with some reluctance but indeed as an honor. My subject was outlined to cover 'Energy Resources - both nuclear and conventional' as related to your theme 'Minerals - Treasure Trove of the West'. This is indeed quite an order and I hope you will forgive me for concentrating mainly on the nuclear-uranium portion with brief references only to conventional fuels some of which will be covered in detail later in your conference. In regard to Uranium, I am speaking on the fringe of the area containing half the uranium reserves in your country and no doubt to many who are very conversant with knowledge of these resources. Nevertheless since our two countries have been very closely allied in both nuclear developments and uranium supplies I hope an exchange of information may be mutually beneficial. Concentration on the nuclear fuel resources is I hope understandable as nuclear energy is the coming source of power which will augment the rapid demand in the industrialized countries and provides hope for economic power in many of the more underdeveloped countries. The situation regarding conventional fuel resources is more widely known and their expanding future revolves around production cost reductions, research into diversified uses, plus more assurance of imports from countries less effected by international controversies determining export policies.

Jan 1, 1967

By F. Gonzalez, A. Zambrano, J. Schwoebel, S. Kravits

Significant lost time delays were experienced by Carbonifera de Nueva Rosita, S.A. de C.V. ("CNR") during mining development of the Pasta de Conchos Mine ("the Mine") near Nueva Rosita, Coahuila, Mexico. Furthermore, methane gas concentration in the return air course had exceeded 1.0 percent. Resource Enterprises, Inc. ("REI") was contracted by CNR to recommend an approach to reduce methane emissions at the Mine. In order to recommend a degasification approach, REI and CNR obtained geologic and reservoir characteristics of the Double coal seam, Olmos Formation. A vertical core hole was drilled to obtain core samples to determine gas content (average 8.4 cm3/gm) and to conduct a slug test to estimate permeability (34 md). This information was used to simulate gas productivity and drainage effectiveness. The simulation indicated that underground horizontal boreholes would remove significant quantities of gas in advance of mining in a reasonable period of time. Based on the results of the simulation study, an underground degasification drilling program was initiated at the Mine. In a six month period, five long in-mine degasification boreholes were drilled in advance of CNR's three to five years mining projections. Peak gas production from the five boreholes (approximately 2,750 cumulative meters) had exceeded 45,000 m3/D. Results to date have indicated a general reduction in methane concentration in the return air course below 0.8 percent.

Jan 1, 1993

By Robert J. Clarke

Reflections on over ten years experience handling bituminous coal from railroad cars to ground storage and lake vessels. The arrangement of the facilities is described but the basic theme of the discussion is the experience gained and lessons learned from facility operation. The Great Lakes provide the maritime environment for the economical transport of vast quantities of raw materials from their source in the Upper Lakes (the Mesabi Range, for instance) to Lower Lake Ports. Lake Erie, because of its proximity to the steel centers , blossomed with the great ports that now line its southern shore - Toledo, Sandusky, Lorain, Cleveland, Huron, Ashtabula, Conneaut and Erie.

Jan 1, 1981

By Charles Kocsis, Pedro Nascimento, W. Patrick Arnott, Samuel J. Taylor

Respirable crystalline silica (RCS) is an inhalation health hazard for mining and industrial work environments and must be monitored. We provide theoretical analysis of real-time measurements for determining RCS mass concentration without the use of filters by using photoacoustic spectroscopy. The suspended dust in the mine air can be continuously sampled by the photoacoustic instrument. A tunable quantum cascade laser is the light source, allowing for determination of interferences such as kaolinite, coal dust, and water vapor. The most useful spectral region is found to be between 11 and 13 μm. Absorption by water vapor, and, to a lesser extent, carbon dioxide, in this spectral region has gaps that allow for quantification of the aforementioned dust species as well as a convenient check on the calibration of the instrument. This work brings photoacoustic measurement of aerosol to the mid infrared range where spectrally dependent light absorption can be used to quantify dust composition and mass concentration.

Jul 31, 2022

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By Daniel H. White

Block caving, unlike most other conventional forms of mining relies principally on the natural forces within the rock mass to fragment and transport the ore. Obviously, not every orebody can be satisfactorily mined by block caving. In the early stages of mine planning an attempt should be made to assess the benefits of the block caving system relative to others, and develop a reasonable mining concept that may be used to provide preliminary information to mine planners and financial specialists. It is the intention of this paper to outline some basic geotechnical parameters that are essential to: 1) Assessing the feasibility of block caving an orebody and 2) Providing semidetailed information relative to mine design based on drill hole and other data.

Jan 1, 1979

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

By G. Thorsen

An alternative way to the normal practice of precipitation of jarosite, goethite, or hematite for removal of iron from zinc sulphate process liquors/ is to employ the techniques of solvent extraction. The process presented avoids the addition of any external alkali for the extraction of iron by integrating the leaching and solvent extraction steps in a hydrometallurgical zinc plant. By starting the leaching of zinc from the solid zinc calcine material with an organic solution of an acid liquid cation exchanger, the organic phase is loaded with the organic zinc salt from the direct reaction with zinc oxide. The residue from the organic leaching is transferred to a hot acid leach circuit where the remaining zinc oxide and the zinc ferrites will dissolve form¬ing an aqueous sulphate solution of zinc and iron. In the subsequent solvent extraction of iron from this aqueous leach solution, iron is exchanged with zinc from the organic phase. The commercial carboxylic acid Versatic 10 (Shell) is highly efficient for this integrated process of leaching and solvent extraction. The resulting iron-loaded organic phase is heated to 150-200 C in the presence of water whereby the iron will be directly precipitated from the organic phase as iron oxide of high purity and the regenerated organic acid is recycled to the organic leaching step for reloading with zinc.

Jan 1, 1980

By Leonard Sugin

As we approach the end-of the 20th century we are made more aware of the tremendous role that energy plays both directly and indirectly in our varied way of life. The industralized nations of the world have already established industries and economies which are greatly dependent upon the availability of energy. The underdeveloped and developing nations of the world are slowly and surely moving to the same utlimate requirements. The world wide need for distribution of energy sources is continuing to grow. At the present time there is a great imbalance between the sources of energy and the consuming economies In order to bring about greater equality between supply and demand major efforts and large capital expenditures are constantly being made. Industralized areas are seeking their own independent sources of energy whereas those areas of the world which contain great reserves of energy are limiting its export as well as developing its own industralized capacity. Nevertheless, energy bearing materials are still transported great distances in order to satiate the appetites of power hungry economies.

Jan 1, 1975

By L. R. Hossner

Chemical and physical properties of surface soils and overburden materials must be evaluated prior to strip mining activities. This information can be used to assess whether subsurface overburden can be equal in quality to the existing surface soils, especially when these soils are classed as prime farm lands. In Texas, materials from the Carrizo, Calvert Bluff, Simsboro, and Hooper Formations overlie the lignite. The Carrizo Formation consists of thick clean sands with poor water and nutrient retention capabilities. These materials are least suited for placement of the surface of reclaimed land. The oxidized, medium textured overburden from the Calvert Bluff and Simsboro Formations possess adequate water and nutrient properties and are better suited for sustained plant growth. Non-oxidized Calvert Bluff and Hooper sediments generally have acceptable properties for reclamation. However, caution must be exercised in vegetating these materials since they may contain acid forming sulfide minerals.

Jan 1, 1982

By C. E. Silverblatt

The advent of larger quantities of -1/4 inch coal in the raw feed to the preparation plant and the necessity of recovering this material has made the problem of meeting product moisture specifications more difficult. For a number of years thermal dryers have been used advantageously as a means of reducing fine coal moisture content where the over-all economics would justify such an installation. However, these units are not without their drawbacks because of high capital and operating costs, safety hazards and possible degradation of the product, and thus an alternative method of moisture reduction is highly desirable. After the various mechanical variables associated with filtration have been optimized, an examination of theory shows that surface tension and liquid viscosity are the only two remaining variables which might be altered to reduce moisture content.

Jan 1, 1964

By W. A. Mathews

We report on the progress of an automated mineralogical deportment of fluorine (F) in two portions of the Grasberg District for the development of metallurgical amelioration protocols for Cu sulfide concentrates. Fluorine detection limits in automated SEM technologies range from 1% (TIMA) to about 9% (QEMSCAN), however substitution in hydrophobic minerals or those reporting to concentrate is typically much lower (

Mar 2, 2022

By D. Brandt

The Dos Pobres Mine is a copper oxide heap-leach operation located near Safford, AZ. Mine production is 163 kt/d (180,000 stpd) with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority. The engineering department began a project to improve fragmentation through blasting and thus increase throughput in the crushing system. It soon became clear that input from other departments was going to be required to make this a safe and economical project. Therefore, the crush and convey and ore control departments worked together to evaluate all available data on blast patterns and explosive loads and tracked performance and results. Using image analysis, drill energy index and databases, improved fragmentation size has been achieved and results have been verified while controlling costs.

Jan 1, 2011

By R. Asamoah, P. Forson, W. Skinner, M. Zanin

Despite the seeming benefits decoupling pyrite and arsenopyrite minerals present in practice, little success has been achieved. The present study presents possible process routes for attaining selective flotation broadly capitalizing on differential oxidation between these minerals, and the use of a chelating collectors. The best performance was achieved with dithionocarbamate application following copper activation, yielding 81.4% arsenopyrite and 37% pyrite recovery. Preaeration followed by staged addition of xanthate produced 76% arsenopyrite and 31% pyrite recovery while reverse flotation of pyrite after H2O2 addition gave rise to rejection of 66% pyrite accompanied with 24% arsenopyrite.

Mar 2, 2022

By Bartłomiej Bursa, Paweł Stefanek, Paweł Stefaniak, Sergii Anufriiev, Wioletta Koperska, Maria Stachowiak

The article presents the main functionality of the DSS class system for monitoring and stability assessment of tailings storage facilities. The presented demonstrator was deployed on the example of the Żelazny Most reservoir - the largest active facility of this type in Europe and the second one in the world. Considered a high-risk structure, it demands a system capable of online analysis of big data from various sources using machine learning, 3D modeling, or GIS mapping with the functions of interactive time-spatial analysis. In this paper, we present a complex calculation module with an integrated user interface.

Jun 25, 2023