Search Documents

By Henning R. Norbom

Lime has been produced for many centuries. The simple pot kiln was one of the first devices used in this process. It was constructed of stone often on the side of a hill to reduce construction efforts and provide easy access to the top for feeding of limestone. It was fired from below with wood and coal. The pot kiln was very small and operated on the batch principle. The kiln being cooled between each batch, the fuel consumption was horrendous. The lime quality was poor with perhaps only one half of a batch being lime of suitable quality. Of the remaining half one part would be over burned and another part underburned. For centuries the lime burning technique was improved at a barely recognizable rate. One of the first major steps forward was the introduction of the continuous process vertical lime kiln. Although at first crudely constructed, the kiln had a refractory lining. It was charged with alternate layers of limestone and solid fuel usually in the form of coke. Continuous mode of operation, larger unit size and better heat distribution resulted in greatly improved fuel economy. However, quality of lime produced still left much to be desired. One problem was contamination by ashes from solid fuel.

Jan 1, 1978

By D. D. Harbuck

Previous studies at the U.S. Bureau of Hines have shown that only 70 to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the Bureau developed and researched the hypothesis that minor amounts of germanium and zinc silicate, both present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of silica gel formed increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1991

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By Dirk van Zyl

It can systematically assess if the control and management systems designed for protection of sensitive ecosystems are adequate. The results of the assessment can help to identify key elements in the project that pose higher risks due to uncertainties in design. These assessments can then be used to make recommendations to further manage and reduce risks as the project is developed. QUALITATIVE RISK ASSESSMENT The general principles of a risk assessment are well summarized by Kaplan and Garrick (1981): "In analyzing risk we are attempting to envision how the future will turn out if we undertake a certain course of action (or inaction)." Fundamentally, therefore a risk analysis consists of an answer to the following three questions: What can happen? (i.e. what can go wrong?) How likely is it that that will happen? If it does happen what are the consequences?" Risk assessments can be performed using various levels of sophistication depending on the amount and accuracy of data available. A qualitative risk assessment uses descriptors throughout to express the level of risk. The definitions of the descriptors are presented in terms of the magnitude or concentration of contaminants. The results of a qualitative risk assessment can be used to: a)Document the evaluation and decisionmaking process. Although differences of opinion may exist about the definitions of the descriptors, the process is well-documented; b)Express the relative risk associated with specific activities or design elements; and, c)Select those failure modes or release mechanisms that may result in significant risks. These mechanisms can then be further developed in quantitative risk assessments. A qualitative risk assessment can be performed in a systematic approach using four steps (Van Zyl, 1987): A qualitative environmental risk assessment can be used to describe the risks associated with the development of a new mine and to make an evaluation of the adequacy of its design for environmental protection. The relative magnitude of risk associated with selected failure modes and exposure/consequence scenario assessments is the final result of a qualitative risk assessment. These failure modes are based on site specific areas and components, and mining and construction phases. The four steps of a risk assessment (hazard assessment, exposure assessment, consequence assessment, and risk characterization) are used in the development of a qualitative risk assessment. Relative magnitudes (using a five point scale of negligible to high) for each step, can be quantified in a qualitative risk assessment. Development of the descriptors for the relative magnitudes in each step is a very important part of a qualitative risk assessment. The success of a qualitative risk assessment depends on the adequacy of the information base and the subjective judgements made in each step. The quality of the risk assessment is, therefore, dependent on the experience of the assessors. A mining project in a sensitive coastal environment is presented as an example to demonstrate the application of a qualitative risk assessment. INTRODUCTION Environmental impacts from mining operations have been a significant factor in the last century. This was especially the case prior to the development of a better understanding of environmental processes and the potential impacts of acid rock drainage (ARD), and associated heavy metals, or the uncontrolled disposal of tailings and waste rock (Smith, 1987). Much care has been exercised over the last two decades in designing and operating mines to limit the environmental impacts as far as possible. All new mines are specifically designed with mitigative methods to manage such potential environmental impacts. Attention is directed to ARD impacts, safe disposal of mine waste rock and tailings, transportation and storage of chemicals and fuels, and final reclamation. A qualitative risk assessment can be used to address all project systems and activities that may potentially pose a risk to the environment.

Jan 1, 1992

By Douglas F. Crickmer

Pocahontas Land Corporation, a wholly-owned subsidiary of Norfolk and western Railway Company, owns a 100,000-acre block of coal lands in Martin, Johnson, Pike, Floyd and Lawrence Counties, Kentucky. These holdings were largely acquired in three major purchases between the years 1942 and 1959. The area is undeveloped and constitutes a part of the coal reserve for future mining. This block, which is principally in Martin County, lies in a triangle formed by the Levisa and Tug Forks of Big Sandy River on the sides with Dewey Dam at its base and the Town of Louisa at the apex. The topography'is typical of eastern Kentucky and consists of steep hills rising from 500 to 800 feet above creek level. There is little level ground in the area. As a matter of fact, some roads are on the creek bottoms with what little bottom land is available in the hollows being utilized for small-scale farming. The steep hills are marked by three separate massive sandstone formations which form cliffs ranging from 40 to 100 feet in height.

Jan 1, 1964

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By İlknur Erol

The abstract highlights that hearing loss is an occupational disease caused by noise exposure in the workplace. The study investigates noise-induced hearing loss among miners in underground coal mines in Turkey, considering factors like occupation, age, and exposure time. The research employs logistic regression analysis to reveal the relationship between hearing loss and these factors. The findings suggest that occupational groups and duration of noise exposure significantly affect hearing loss. Miners in production groups and those exposed to noise for 10-14 years have a higher risk. The study concludes that age does not significantly increase the probability of hearing loss.

Mar 24, 2022

By C. Huang, S. Lin, Y. J. Wang

Introduction A mine characteristic curve is of great importance for both theoretical analysis and daily management of a mine ventilation network. Ventilation engineers are well acquainted with the ways of obtaining and using a mine characteristic curve that is conventionally associated only with single-fan networks. However, for a multiple-fan network, difficulty has long been recognized in defining the curve, not to mention, obtaining or using it. To extend the concept of mine characteristic curves for a multiple-fan network, a subsystem-based approach has been introduced by Wang (1992a). He defines a subsystem characteristic curve for a multiple-fan network and discusses the numerical procedure for constructing the curve. A graphical method of obtaining a subsystem characteristic curve for serial-parallel, multiple-fan networks has also been accomplished (Wang, 1992b). In spite of the maturity of the fundamental concepts related to and the numerical analysis tool for a multiple-fan ventilation network, information regarding the related laboratory tests is very scarce. To make up this gap, laboratory experiments have been done by using a two-fan experimental network. This paper presents the methodology and major findings regarding the construction and features of a subsystem characteristic curve. Characteristic curves and measurement fundamentals A characteristic curve A characteristic curve is a graphic presentation of the relationship between any two variables of a two-terminal component. It is typically defined in the form of a quantity-pressure curve for a ventilation component, which can be a single branch (airway), a fan, a regulator, a portion of a network or even a whole network. If a component is a single branch, the curve is called a branch characteristic curve. If it is a fan, then the curve is called a fan characteristic curve, and so on. Figure I illustrates the characteristic curves of some typical ventilation components. A general method for obtaining a characteristic curve from measurement is to apply an adjustable-pressure source between the two terminals of a component and measure the quantities corresponding to the different pressures. Mine characteristic curve A single-fan network can be easily divided into two ventilation components, the fan and the remaining network. The latter consists of only branches and regulators. Under this subdivision scheme, two characteristic curves can be constructed. They are the fan characteristic curve and the characteristic curve of the remaining network. The latter is referred to as the mine characteristic curve or the system characteristic curve. Although the general method for constructing a characteristic curve from measurement can be applied to obtain a mine characteristic curve, there is a shortcut for constructing the curve by introducing a mine resistance factor R. It is a constant if all of the resistance factors in the network are constant. R relates mine pressure H with quantity Q as in: H=RQ2 (1) For a given R, Eq. (1) can be directly used to plot a mine characteristic curve by assigning a series of Q values and calculating the corresponding H values. Hence a shortcut to constructing a mine characteristic curve is to measure one set of mine pressure H and quantity Q values, calculate the mine resistance factor R using Eq. (1) and then plot the curve. Subsystem characteristic curve Applying a similar scheme as is used for a single-fan system, divide a multiple-fan network into two components, a fan under consideration and the remaining network that contains all the other elements (branches, regulators and remaining fans) of the network. The fan under consideration

Jan 1, 1994

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By Michael L. Clar

Reclamation of surface mined lands has two basic objectives: (1) the elimination or abatement of undesirable environmental conditions, and (2) the restoration of mined land to its former or more productive uses. This paper addresses some of the planning concepts and site factors that influence the selection of suitable land uses for surface mined lands. Three planning concepts included in the discussion are: (1) mine land planning, (2) comprehensive land use planning, and (3) environmental site planning. The site factors that will influence the selection of an appropriate land use have been grouped into three categories: (1) legal, (2) geographic, and (3) natural. The natural factors are further subdivided into three groupings: geomorphology, soils, and climate.

Jan 1, 1981

By Harold Bloom

Dimethylglyoxime reacts with nickel in a buffered ammonical-citrate solution containing the detergent ?Aquet? and hyroxylamine-hydrochloride. The resulting nickelous dimethylglyoxime is extracted with xylene. Visual comparison with standards permits the estimation of from 50 to 10,000 ppm of nickel. Soil, rock, or sediment may be decomposed by digestion with (1-3) nitric acid, allowing about 70 determinations per man-day to be carried out. With minor modifications to the above procedure, sediment and soil may be semi-quantitatively analyzed for nickel at the sample site. The chemical equipment is easily portable and the analysis extremely rapid because the buffer, dime thylglyoxime and xylene are added simultaneously to the sample and no heating is required. The sensitivity varies with the "availability" of the nickel ions; under favorable conditions, one may obtain a positive test for as little as 10 micrograms in soils and sediments. This procedure is similar to one, for the field determination of heavy metals described elsewhere by the author.

Jan 1, 1958

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

By J. Drelick

Among the wide variety of modern surface chemistry analytical techniques, contact angle measurements still remain attractive for wetting characterization of solid surfaces. The captive-bubble and sessile-drop techniques are the most popular methods for the examination of flotation systems. Systematic measurements of advancing and receding contact angles for several three-phase systems using the captive-bubble and sessile-drop techniques show that the contact angle measurements depend on the technique used and may differ significantly for some heterogeneous and rough solid surfaces. Importantly, it was found that these discrepancies in contact angle measurements depend on the bubble (drop) size. Contact angles as measured with the static captive-bubble technique are compared with those measured with the dynamic captive-bubble technique, in which the capture of a bubble at the solid surface results after buoyant transport and attachment The dynamic captive-bubble technique allows for the formation of much smaller bubbles than is possible with the static placement technique in which a bubble is placed at the solid surface with a microsyringe. Although this dynamic technique cannot be recommended for the systematic wetting characterization of solid surfaces, its significant advantage is the ability to examine the contact angle/bubble size relationship over a wide range of bubble sizes, from several micrometers to several millimeters in diameter.

Jan 1, 1995

By William D. Mayercheck

Beginning in 1974, the Bureau of Mines, U.S. Department of the Interior, sponsored R & D efforts related to further development and use of continuous face haulage in underground coal mines (Cowan, 1975). The U.S. Department of Energy continued this effort as of October 1977. This paper represents an update of an article previously published in Mining Engineering magazine (Mayercheck, 1979). Development progress is summarized for a variety of prototype systems or components now being built, surface tested, or tried underground.

Jan 1, 1981

By W. J. McDonough

Rapid growth and acceptance of engineered materials have changed the way we live. We have come to expect improved performance at less cost. At the same time, our awareness of societal and environmental issues created by these materials during and after their lifetime has been heightened. As a result, material lifecycle analysis is receiving considerable attention. Material lifecycle analysis evaluates the cost/effective tradeoffs at each stage of a material's life: feedstock, fabrication, performance, recycle, and disposal. The U.S. Bureau of Mines investigates a material's lifecycle using technical cost models augmented with decision and impact analyses. Results of these studies are useful in gaining a better understanding of current material selections and illustrating the multifaceted issues associated with engineered materials in today's society.

Jan 1, 1992

By J. D. Pitts

The worldwide production of iron ores was approximately 880 million metric tons in 1975. This level is the result of an annual growth rate of nearly four percent during the period 1967 to the present. The high growth rate was particularly significant in that two relatively severe worldwide recessions occurred in 1971 and 1975. The current upturn in world economic growth will probably allow future annual iron ore production growth rates in excess of the four percent figure, and, in fact, the International Iron and Steel Institute (IISI) has predicted that a five percent rate should be realized through 1985. The IISI figures would indicate a 1.4 billion metric tons per year output by 1985 or an increase in current production levels of around 500 million metric tons per year (MMTA)1. Even the more conservative four percent growth rate prediction from historical data would provide an 2 increase over current figures of nearly 350 MA by 1985. A large portion of world iron ore production is being provided by large resource-rich countries with relatively new industrial bases. These countries are typified by heavy export of raw materials such as iron ore and ore products and a large capital investment in the facilities to recover these raw materials. Brazil and Australia are typical of such countries and, indeed, their production of iron ore in the period 1967 to 1973 increased at annual rates of 17 to 30 percent, respectively, The continual reassessment of resources in these and other major iron ore exporting countries such as Venezuela and Liberia would indicate chat these high growth rates may continue for some years to come to meet anticipated world demand for raw steel production.

Jan 1, 1976

By J. Szarkowski

"INTRODUCTION The Butte district of Montana is well-known as one of the biggest historic producers of copper in the world. It is also a classic example of a porphyry Cu-Mo system that has been overprinted by zoned, polymetallic (Cu-Zn-Pb-Ag) lode mineralization. After copper, silver was the next most important metal mined from Butte, with over 700 million ounces of total Ag production between 1880 and the present day. Although many papers have been written on the mineralogy of the early porphyry Cu-Mo mineralization and the high-grade Cu-rich lodes in the center of the district, relatively little information exists on the mineralogy of silver in Butte. The purpose of this paper is to summarize past and present silver production trends for the district, and to combine previously published work with new research to examine the mineralogy of silver in the Butte mining district. BUTTE HISTORIC SILVER PRODUCTION According to a recent USGS compilation1, Butte is one of the most Ag-rich porphyry deposits in the world, both in terms of average Ag grade (8.6 g/ton) and total production + reserves (Fig. 1). It is also the 2nd biggest Ag-producing mining district in the U.S. (after the Couer d’Alene district, Idaho). Annual silver and copper production data for the Butte district, compiled from various sources2,3,4, are summarized in Figure 2. Peak production of Ag and Cu was in 1917. While Ag production gradually declined in the ensuing decades, Cu production remained strong until the years leading up to the closure of the Berkeley Pit in 1982. In 1984, mining of the nearby Continental Pit resumed under a different operator, and continues to the present day. The Continental mine produced an average of 35,000 metric tons Cu and 575,000 oz Ag per year between 1984 and 20044. These figures do not take into account a period of mine closure in 2001-2003 due to an unexpected hike in utility prices. The long-term decline in Ag/Cu ratio of ore mined in Butte (Figure 3) is due to several factors, including: 1) changes in metal prices; 2) a downwards decrease in Ag/Cu ratio of most of the lodes with depth below surface; and 3) a shift in mining methods from selective underground mining of high-grade veins to open-pit mining of the bulk rock."

Jan 1, 2016

By J. Armstrong, J. Bourgeois, S. Warren

The application of statistical analysis software programs has proven useful for investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Mar 2, 2022

By Boyd Eisenbraun, Dennis Murr, Milton Rojas

Approximately since 1925, the phenomena of grinding and classification of minerals with screens have been studied. In the U.S. iron ore mining operations located in the so-called “Mesabi Iron range,” magnetite processing plants have made progress in the application of high-frequency screens that have allowed them to process low-grade Taconite ores and successfully achieve the economic benefit of these minerals. In the particular case of magnetite minerals disseminated in the siliceous matrix, the main objective is to reduce the generation of particles called “middlings” with high silica contents. Commonly the primary challenge of the metallurgical task is to achieve high recoveries and iron concentrates with low impurities. To achieve this, several studies and industrial applications have shown success in this regard and not only in iron ores, but also in other minerals around the world. The study described in this paper attempts to describe some key aspects that helped develop an effective solution and list the benefits associated with this modern process design by using industry-proven technologies for minerals in Chile that have similar characteristics to the minerals of the iron belt in the United States.

Feb 1, 2025

By E. R. Bauer

The ground control aspects and occupational safety concerns of extended depth-of-cut mining are presented in this U.S. Bureau of Mines (USBM) report. The scope of extended cut use and typical face operations while extracting extended cuts is reported. A comparative review of roof fall fatalities and a statistical analysis of accidents and injuries for both extended and nonextended cut mining is included. The views and opinions on extended cutting from a series of interviews with mine workers in five states are summarized. In addition, some of the problems and safety concerns of this extraction system are mentioned.

Jan 1, 1995