Search Documents

By Steven J. Kirk

In the past decade, many hardrock surface miners have revegetated dumps and tailings ponds to allow those waste disposal areas to blend more easily with the surrounding landscapes. Efforts have also been made to more creatively use the flat land resulting from the disposal of overburden and tailings. However, the mines which serve the best post-mining land uses are those that have been preplanned to incorporate such end uses. To more fully explore such a philosophy, interdisciplinary team from The University of Arizona conducted a study during 1974 and 1975 of six open pit copper mines in the Santa Cruz River Basin south of Tucson, Arizona for the purpose of investigating both interim and end-use possibilities for mine waste disposal areas. Among other reasons for the study, it was felt that alternatives for such waste areas would be more socially acceptable than barren dumps or tailings ponds. The team, known as the Mines Project Group, consisted of architects, engineers, and hydrologists. As it would have been economically infeasible to move the existing waste rock dumps or tailings ponds, preplanning was limited to the disposal of waste generated after the inception of the project. To better present their concepts, architecture professors Kenneth Clark and Fred Matter constructed a large-scale cardboard relief model of the mines and the surrounding Santa Cruz River Valley (1). The model was built at a scale of 1:12 000 (1 in = 1000 ft) with 30.48 m (100 ft) contour intervals and covered an area of 40.23 km by 32.18 km (25 miles by 20 miles) in scaled area. The mines being studied were cut into the model, but the proposed waste dumps and tailings ponds were built separately so different disposal configurations could be evaluated.

Jan 1, 1980

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Robert D. Thomson

The plastics industry runs into the billions, both in the dollar value of its finished, products and in the pounds of plastic raw material produced. It is, too, one of the fastest growing industries with a 300 percent increase in production in the past ten years. Informed estimates set 5.9 billions pounds as the plastic volume for 1959. Statistically, this is equivalent to a per capita consumption of 25 pounds in the United States. Plastics are man-made materials in contrast to natural materials like wood and are a family of materials -- not a single material - each member having special advantages. A generally accepted definition; for plastics is; a large and varied group of materials which consist, wholly or in part, of combinations of carbon with oxygen, hydrogen, nitrogen, and other organic and inorganic elements. This, while solid in the finished state, at some stage in its manufacture is soft enough to be formed into various shapes, most usually through the application either singly or together of heat and pressure. Many combinations and many different materials are thus possible. Therefore, for purposes of simplification, most plastics can be classified under one of 14 recognized basic family groups. These groups in turn generally can be further classified into one of two major subdivisions - thermosetting or thermoplastics. A few plastics are in between and they can be formulated to be either thermosetting or thermoplastic.

Jan 1, 1960

By A. Bruynesteyn

Results are presented from a series of tests designed to determine the beneficial effects of the microorganism Thiobacillus ferrooxidans upon the leaching of uranium from a pyritic uranium ore. Minus 1-inch (-25mm) 0.0711 percent uranium containing, pyritic ore from the Rio Algom Mine at Elliott Lake, Canada was leached with lixiviants of various Eh and pH as well as being subjected to a biologically-assisted ferric iron leach. In all cases, the biological leach gave superior extraction. At pH 1.6, the biological leach gave 100.6 percent extraction and the ferric iron leach 69.8 percent. This improvement in extraction is associated with a relatively rapid biological breakdown of the pyritic material, thus liberating uranium mineralization associated with these pyritic materials and regenerating the ferric sulphate lixiviant in situ.

Jan 1, 1981

By Milan Lipensky

This paper discusses the longwalling practices used at the San. Francisco Mine of Compania Minera Autlan in Mexico, in. the mining of a sedimentary, manganese deposit. Bethlehem. Steel Company is a part owner of this property. The San. Francisco Mine is located approximately 580 miles west of Mexico City, on the outskirts of the town of Autlan, in the State of Jalisco. The ore is shipped from the port of Manzanillo 120 miles southwest of Autlan. The mining method is a variation of the longwall retreat system, using friction. props that, until recently, had been used only in coal mining operations of Europe and the United States. However, due to the structure of the ore body and the modified longwall system that is practiced, there exists some unusual variations, such as: .1) friction props set by a mechanical two-step lifting device, 2) drilling and blasting, against the friction props, 3) a highly fractured and undulating, volcanic tuff roof; 4) displacement faults-up to 5 meters, and 5) a relatively stable, irregular floor.

Jan 1, 1964

By C. Villa Diniz

It is proposed that battery grade Mn02 can be produced directly from a manganese ore from Azul Mine in Brazil, by leaching with HCI to remove heavy metals selectively. We are working to find a way of selectively separating Cu, Ni, Co, Pb and Fe from the resulting acidic manganese chloride solution, to detoxify it and produce marketable chloride solution. Chelating ion exchange resins are proving more promising for this separation than solvent extraction with commercially available reagents. Results from batch and column ion exchange tests that characterize the behavior of copper, nickel, cobalt, lead and iron are reported.

Jan 1, 1999

By G. J. Hartman

The Fort Cady in situ borate mining project involves recovery of boron from a mineral deposit located over 1400 feet below the surface. The resource recovery method is being developed using in situ mining technology employing weak acid solution injected directly into the ore body. As the acid contacts the calcium based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by use of submersible pumps. At the surface the borate values are recovered as a finely divided solid white powder after a series of chemical reactions and precipitations resulting in the production of calcium borate. The refined product is then sold under the trade name CADYCAL 100.TM All environmental permits for up to a production rate of 90,000 tons per year have now been obtained. These permits required an Environmental Impact Study (EIS) for federal lands and an Environmental Impact Report (EIR) for the private portion of the property. Regulatory permitting took over 5 years to obtain all authorizations for this operation. The ore body has an average thickness of 118 feet extending over 273 acres. At a production rate of 90,000 tons per year with only a 70 percent resource recovery allowance, in place reserves are sufficient to sustain production for over one hundred years.

Jan 1, 1997

By Abdelaziz Baçaoui, Imane Aarab, Mohammed Derqaoui, Abdelrani Yaacoubi, Khalid El Amari, Abdelmoughit Abidi, Abderahman Etahiri

Numerous researchers have addressed the complexity of the direct flotation separation of apatite from low-grade phosphate ore. The majority of these studies were limited to the micro-flotation scale. In fact, there is no warranty that a reagent scheme that showed a direct flotation of apatite at a micro-flotation scale on pure minerals would automatically replicate the same expected results on the natural ore in the mechanical flotation cell and so was the case for the phosphate ore studied. The overall trend was concentrating apatite in the non-float product. This study aspired to thoroughly assess the flotation performance of this never-exploited low-grade sedimentary phosphate using design of experiments (DOE). Unveiling new insights on such a strategy twist, various parameters and operating conditions, namely, desliming, type of collector and depressant, reagents dosages, conditioning times, flotation time, and pH, were addressed by multiple-factor screening using asymmetrical fractional factorial design followed by statistical interpretations. The collectors tested were the sodium oleate and a fatty acid mixture (FAM). The depressants tested were sodium alginate (NaAL), corn starch, carboxymethylcellulose (CMC), and sodium silicate. The results of the multivariable analysis revealed that desliming, pH, collector dosage, and flotation time significantly influenced the flotation process. Desliming was beneficial for the yield, P2O5 recovery, and SiO2 removal; however, there was still a compromise between grade and recovery. A strongly alkaline pH value of 12 stood out from the whole range. P2O5, CO2, and SiO2 grades of the products and flotation recoveries were improved, except for P2O5 recovery, which was negatively affected. A collector dosage between 2000 and 3000 g/t increased the P2O5 grade and reduced CO2 grade and recovery, enhancing the apatite/carbonates separation. A flotation time of 15 min was significant for P2O5 grade and CO2 recovery, nevertheless, at the expense of yield and P2O5 recovery. The products having initial concentrates of 28.08% P2O5 with a recovery of 88.96% and 29.41% P2O5 with a recovery of 62.71% were obtained using 25 g/t of NaAL and 2000 g/t of the collector FAM and sodium oleate, respectively, at pH 12.

Jun 5, 2022

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in by-product molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have reduced the possibility ofH2S gas evolution immensely. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Benchscale rougher flotation results for samples from the Sierrita Cu–Mo plant showed the best DCMTperformance at 8 kg/t of DCMT and pH=10.5 with 30 min of shear conditioning and 10 min of flotation conditioning time. The Aminpro plant model simulation confirmed that DCMT with 4–8 kg/t under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared to NaHS.

Apr 19, 2021

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By Kenneth S. Johnson

Large reserves of high-purity Permian gypsum crop out and are at shallow depth in three regions of western Oklahoma, Gypsum beds in the Blaine Formation are 10 to 30 feet thick and are generally 95 to 99 percent pure, whereas the massive Cloud Chief Gypsum is 20 to 100 feet thick and is 92 to 97 percent pure. Reserves are estimated at 48 billion short tons. Eight companies in the State currently mine about 1 million tons of gypsum each year for wall- board, for plaster, as a retarder in portland cement, and as a soil conditioner. Future uses, under more favorable market conditions, may be in the chemical industries, largely because of gypsum's potential as a source of sulfur. Three thick sequences of Permian rock salt underlie most of western Oklahoma at depths of 30 to 3,000 feet. Individual salt beds 5 to 30 feet thick are interbedded with thinner layers of shale and anhydrite. Five large salt plains, fed by natural springs of saturated brine constitute additional resources of salt. Reserves, estimated at 20 trillion short tons, are virtually untapped, and, ironically, about 90 percent of the salt used in Oklahoma is imported. Chemical data on the rock salt are lacking, but evaporated salt produced from brines is generally 97 to 99 percent pure. Current production from three solar-evaporation plants is used mainly for stockfeed, recharging water softeners, and deicing roads. Potential uses are in the chemical industries, where salt or brine is a necessary raw material.

Jan 1, 1973

By Caibin Wu, Bin Xie, Jiaqi Tong, Ningning Liao, Chong Zeng

Understanding the energy-size reduction relationship is vital to grinding process; therefore, this paper aims to show the energy-size reduction of magnetite-calcite binary mixture in a laboratory wet conical ball mill. Single magnetite, single calcite, and blended magnetite-calcite mixture at three weight ratios in four particle sizes were ground in a laboratory wet conical ball mill at four grinding time periods. The results showed that the particle size distribution of both fine particles and coarse particles of single and mixture ground product fitted well with the PSD computed by Rosin–Rammler-Benne function. The larger mass percentage of calcite is, the higher t10 of binary mixture ground product is. On the contrary, t10 in the mixture decreases as the percentage of magnetite in the mixture increases. The different breakage behaviors in blended samples are due to the hardness and particle size. The results of calculated ratio of energy absorption factor showed that the calcite consumed more energy in the breakage process of binary mixture than ground alone. The JK size-dependent breakage model based on the t10 method fits all the experiment data, be it generated from pure minerals, mixtures at different weight ratios, or each component separated from the mixture.

Jun 4, 2022

By Clarence A. Johnson

The discovery of the Prudhoe Bay field temporarily reduced interest in the development of coal conversion processes, but interest is being re¬newed by the current energy crisis. According to M.A. Wright, Chairman of the Board of Humble Oil and Refining Company(l), the reserve in the Prudhoe Bay bield has been confirmed to be about 10 billion barrels. At first glance this appears to be an extremely large reserve which will eliminate supply problems for the United States for some time. This feeling of security is lost when one realizes that by 1980 the world will consume the reserves of a Prudhoe Bay or a Libya, or Venezuela in less than a year, based on the recent predictions of U.S. and world reserves made by Eastman-Dillon, Union Securities Company(2). Recent forecasts of U.S. demand and source of supply made by Kenneth E. Hill of Eastman-Dillon are shown in Figure 1. This forecast shows a decline in domestic supplies (excluding Alaska) after 1973, with the total domestic supply leveling off in 1975 at about 13 million barrels per day. Since the predicted demand increases from about 14 million barrels per day in 1970 to about 20 million barrels per day in 1980, about 35% of domestic consumption must come from imports or non-conventional sources by 1980. More imminent is the shortage of low sulfur fuel oil which has been created by the new, tough air pollution regulations that are basically legis¬lating eastern coals out of the market. As an alternate to importing large quantities of low sulfur fuel oil or importing and desulfurizing regular fuel oil, one of two domestic solutions is possible: stack gas clean-up or solids fuel pretreatment. Stack gas clean-up may be the cheapest approach for old installations, but fuel pretreatment has real advantages for new installations. Coal pretreatment at the mine could eliminate all solids fuel handling

Jan 1, 1972

By A. L. Hinde

The recovery of heavy minerals by gravity concentration during grinding is practised widely in the minerals industry. Studies have shown that the grade and recovery of the concentrate depends not only on the performance of the concentrator but also on the degree of liberation achieved in the mills and the scavenging action of the hydrocyclones closing the grinding circuit. In the current study, consideration is given to the development of mathematical models to quantify and unify the operations of comminution, liberation, classification and concentration. The models are based on test work done at production scale with gold ore.

Jan 1, 1985

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

By Judith A. Marks, Deane K. Smith, Jan M. Mutmansky, Maria Klimkiewicz

The mechanical mining of coal seams where roof, partings, and floor rock are extracted along with the coal often introduces large numbers of quartz particles into the mine atmosphere. This study concentrates on the quartz properties in situ and in the airborne dust to determine how they are released from the source rock and whether they are fractured by the mining machinery. Three mines using drum-type continuous miners from different geographic areas were sampled to provide a data base. The roof and floor rocks were primarily siltstones containing 5% to 25% quartz measured by the X-ray powder diffraction (XRPD) method. Much of the work presented here is based on the morphologies of the mineral grains determined by the scanning electron microscope (SEM). The study concentrated on particles of 0.2 to 10.0 µm and on particles containing > 75% Si. Mechanically-crushed quartz particles were also examined for comparison purposes. Particle shapes from the airborne samples suggested that fractured quartz particles were rare. Particle statistics also show that the average size of quartz particles in the airborne samples were similar to the average size of all particles. The conclusion is that very few quartz particles from the source rocks are fractured during mining due to their small initial size and the protection of the associated clays.

Jan 1, 1991

By J. R. Cobble

The Bureau of Mines has developed a process to improve the leaching kinetics of diffusion controlled systems. The system features the Bureau-developed turbomill, an attrition grinder which scrubs the reaction product coating away from the unreacted mineral grains during leaching. The system can be continuously operated at any temperature up to the boiling point of the leaching agent. This paper describes the research on the dissolution of chalcopyrite with acidified ferric sulfate which forms a sulfur product on the unreacted chalcopyrite surface. This method is a hydrometallurgical alternative to chalcopyrite smelter technology which eliminates S)2 emission problems with its associated costs. Batch testing at 90? C with the chalcopyrite/ferric sulfate system resulted in better than 99-pct extraction of copper. At an optimal energy consumption of 1,520 kW h/st, 95 pct of the copper was extracted. Recent work has been directed to development of a continuous system and SX/EW treatment of the resulting pregnant liquor from the chalcopyrite/ferric sulfate leach.

Jan 1, 1991

By Jian Wang, Kun Li, Hao Wu, Juan Nan

In this paper, in order to solve the problems of low accuracy and slow speed of fire flame recognition, an extreme learning machine (ELM) method based on improved Harris hawks optimization (IHHO) is proposed for fire flame recognition. A novel Harris hawks optimization (HHO) is used to solve the problem of parameter selection of ELM. In order to solve the problem that the original HHO is prone to fall into local optimum, firstly circle mapping is used to initialize the population to solve the problem of uneven distribution and small range of the initial population. Then the formula of escaping energy of HHO is modified to make the population have a large range in the middle and late iterations while gradually decreasing in the whole iteration process. Thus, the exploitation stage in HHO is improved to make the search range smaller near the optimal solution to accelerate the convergence process. Finally, at the end of each iteration, a certain number of individuals are selected to perform Gaussian and Cauchy hybrid mutation to prevent the IHHO from falling into local optimization. Through three groups of experiments, the effectiveness of the proposed IHHO and IHHO-ELM is verified. In experiment 1, the convergence performance of IHHO is significantly better than that of the other remaining algorithms in the test results of six benchmark functions. In experiments 2 and 3 of real fire flame recognition case, IHHO-ELM outperforms other remaining algorithms on the whole and has significant advantages in some indexes.

Jan 17, 2023

By Yi Yang, Xiuzhu Su, Wei Sung Ng, Shuiping Zhong, Miao Chen

With over 260 tons of gold reserves, the Shuiyindong gold mine is one of the largest Carlin-type gold deposits in China. A particular challenge in the processing of the ore is the presence of carbonaceous compounds, which can cause substantial losses in recoveries via the preg-robbing and adsorption of gold. To investigate the structural properties of the native carbon and to compare between different characterization techniques for such compounds, pre- and post-flotation mineral samples containing 0.9–4.8% non-carbonate carbon from the Shuiyindong mine have been examined via mineralogical and thermogravimetric approaches, as well as spectroscopic techniques, including X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine edge structure spectroscopy (NEXAFS), solid-state 13C nuclear magnetic resonance (NMR) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, Raman spectroscopy and preg-robbing measurements. NEXAFS and DRIFT yielded the most reliable results, indicating that 60–75% of the organic carbon in all samples consist of aliphatic alkenes with substantial unsaturated content, highly similar to activated carbon, with the remainder being graphitic and humic. Speciation by XPS was sub-optimal due to spectral overlaps between graphitic and aliphatic carbon, and between carboxylic and carbonate functionalities, while NMR spectroscopy could not provide reliable speciation of the carbon groups. The preg-robbing strength was strongly correlated to the aliphatic content and structural disorder in the carbon, while no such relationship was found with the graphitic and humic content.

Nov 29, 2021