Search Documents

By Richard C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1982

By Pierre Mousset-Jones

A questionnaire was sent out to three classes of mines to determine the extent of the heat problem in U.S. and Foreign underground mines. The following list shows the replies received from this questionnaire, however not all the known hot mines in the US replied. A complete listing of the results can be seen in Appendix I. 1) US coal mines - 37 replies 2) US non coal mines - 23 replies 3) Foreign non coal mines - 36 replies. At the present time there are approximately eleven non coal and one coal mine in the US experiencing heat problems which require special efforts to maintain an acceptable working place climate. However since the survey was completed some of them have been placed on standby. The Mine Safety & Health Administration (MSHA) does not have any specific regulations relating to heat stress. Informally the American Conference of Governmental Industrial Hygienists guidelines are followed which use wet bulb globe temperature (WBGT) with values ranging from 26.7°C to 31.1°C for a moderate workload, and different rest regimes. An MSHA report (Misaqi 1976) recommended that conditions should not exceed 26.1°C WBGT for men and 24.4°C WBGT for women. However, quite recently the organizations involved with planning two of the proposed nuclear waste repositories in the United States, have opted for the criteria of an air cooling power of 300 w/m2, and a WBGT of 27'C respectively.

Jan 1, 1986

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By E. D. Gardner, William O. Vandenburg

This chapter on the square-set system of mining em¬bodies the results of a special study of the subject made as a part of the US Bureau of Mines (USBM) general investigation of mining methods and costs. Data for the chapter were gathered by the authors during visits to mines using square-set mining, from information circu¬lars prepared by consulting engineers to the USBM on mining methods at individual mines, and from articles in the technical press and the Transactions of the American Institute of Mining and Metallurgical Engineers. Al¬though some of the properties discussed are no longer in operation, the methods described are still valid. The square-set system of mining has been very widely applied and is one of the oldest methods in use in the US. It is mainly employed for extracting rela¬tively high-grade ore in heavy ground. It is also useful in taking out pillars left in mining by other methods. It is used to some extent as an auxiliary method with many underground systems and as an alternate with cut-and¬fill, shrinkage, and open-stope methods when heavy ground is encountered. In some cases as much as 50% of the ore may be extracted by square setting at mines listed as using some other method of mining. A large tonnage has been mined yearly by square setting, prin¬cipally in the western states. Due to the high cost of timber and the relatively low average production per manshift, this system generally is not used when the ore can be mined by some other method; it usually is adopted as a last resort. Square setting, however, has a special field in that ore bodies not minable by other methods can be stoped by this system. As square-set mining was widely known, there was a tendency for years to use the method regardless of its suitability. With the increasing need for economy and the development of other methods, square setting has been superseded in many mines by cut-and-fill, top slic¬ing, or sublevel caving methods. The term square-set mining as used in this chapter includes all stoping methods in which the space made by the removal of the ore is timbered with framed sets. The sets usually are square in horizontal section. The stope may or may not be filled with waste rock as stoping progresses. HISTORY OF THE SQUARE-SET SYSTEM Prior to 1860, open-stope methods with stulls for casual support accounted for most of the mineral pro¬duction from underground mines. Attempts to mine large ore bodies that required artificial support resulted in disastrous cave-ins and loss of life. The art of mining received a tremendous impetus following the introduc¬tion of methods for mining the bonanza ore body which was discovered in 1860 in the Ophir mine on the Comstock lode, Virginia City, NV. This ore body was phe¬nomenally rich and eventually proved to be 122 m (400 ft) high, 27 m (90 ft) wide, and 98 m (320 ft) long. The mining of this large high-grade ore body taxed the best engineering talent of the time; the problem was finally solved by Philip Deidesheimer. According to Eliot Lord (1882): "At the 50-foot level the vein of black sulphurets was only 3 or 4 feet thick, and could be readily extracted through a drift along its line, propping up the walls and roof when necessary by simple uprights and cap-posts. As the ledge descended the sulphuret vein grew broader until, at the depth of 175 feet, it was 65 feet in width, and the miners were at a loss how to proceed, for the ore was so soft and crumbling that pillars could not be used to support the roof as in coal mines. They spliced timbers together to hold up the caving ground; but these jointed props were too weak and ill-supported to with¬stand the pressure upon them, and were constantly broken and thrown out of place. The dilemma was a curious one. Surrounded by riches, they were yet un¬able to carry them off and their mass of black sulphurets bade fair to become a white elephant on their hands. The Ophir Company began to wish themselves less for¬tunate, as their miners narrowly escaped burial day after day in their attempts to stope out the ore. "A young mining engineer, Philip Deidesheimer, was in charge of a quartz mine in Georgetown, El Dorado County, Calif., in the autumn of 1860, when this serious check to the development of the lode occurred. At the request of William F. Babcock, a trustee of the Ophir Company, Mr. Deidesheimer left his California mine and crossed the mountains with a letter from the direc¬tors of the Ophir Company, authorizing him to inspect the workings of their mines and make such changes in the method of timbering as should seem to him expe¬dient. After examining the vein he designed, in the course of a few weeks, a system of timbering which proved to be exactly adapted to the requirements of the work. Experiments which he had previously made in California gravel and quartz mines furnished the out¬line of his plan. This was to frame timbers together in rectangular sets, each set being composed of a square base, placed horizontally, formed of four timbers, sills, and crosspieces from 4 to 6 feet long, surmounted at the corners by four posts from 6 to 7 feet high, and capped by a framework similar to the base. The cap pieces forming the top of any set were at the same time the sills or base of the next set above. These sets could readily be extended to any required height and over any given area, forming a series of horizontal floors, built up from the bottom sets like the successive stories of a house. The spaces between the timbers were filled with waste rock or with wooden braces, forming a solid cube when¬ever the maximum degree of firmness was desired. By adjustments of these sets the ore bodies along the line of the lode were extracted with comparative ease and security." Most mining methods are evolved slowly and are the result of the combined efforts of a number of minds; Deidesheimer's feat was remarkable in that his system was immediately successful. He died in 1916 at the age

Jan 1, 1982

By Mohammad R. Jafari

The Camp Dresser & McKee (CDM) has been retained by the Sacramento Regional County Sanitation District (SRCSD) to design the Mather Interceptor, a portion of the South Interceptor and Mather Interceptor program. The Mather Interceptor consists of 14,667 feet of 54 to 72 inch gravity interceptor. Approximately 90 percent of the alignment will be constructed via tunneling. Cobbles and boulders in a sand/gravel matrix dominate the ground conditions combined with seasonal perched groundwater table at some of the deeper reaches of the alignment, impacting design consideration. This paper will present the results of a comprehensive geotechnical investigation conducted for this project and in-depth technical evaluation of various trenchless techniques feasible for tunneling in the cobble and boulder laden formations of this project. This paper will also present the risks and issues of the design alternatives and selection criteria.

By C. K. Kocsis, S. Hardcastle

Mine ventilation, requires electricity to operate the fans and fossil fuel for heating. Typically, this accounts for approximately 40% of the overall underground energy consumption. This is considerable, and one of the major causes of this expense is that most mine ventilation systems are designed for the "worst-case-scenario" with respect to ventilation demand, which is commonly dictated by diesel equipment usage. Once designed, mines tend to operate their ventilation system at this peak level despite their exceeding day-to-day development and production needs due to lack of appropriate ventilation controls. In underground metal mines, TeleminingTM, which includes the tele-remote operation of mobile development and production equipment from surface, will change the mine design criteria including its support infrastructure such as the ventilation system. With the removal of machine operators to surface control rooms, conventional ventilation systems designed to dilute and remove pollutants can become redundant. Depending on the ultimate need for ventilation, its cost in automated mines with tele-remote equipment operated from surface will be lower than the cost of ventilation in conventional mines. These cost savings, which could be significant, would not only come from the ability to reduce the amount of ventilation in the mine, but also through the capacity to automate its distribution. This paper provides an indication of the new airflow requirements in stopes and dead-end developments for the tele-remote and automated mining processes based on climatic modelling. Furthermore, this paper makes a cost benefit analysis by comparing the ventilation system operating cost of a conventional underground metal mine based on the mobile diesel powered equipment design criteria with the newly redesigned ventilation system operating cost of an automated mine based on the "heat management" design criteria.

Jan 1, 2002

By A. Arik

An accurate estimation of mining block grades continues to be a challenging task for ore reserve practitioners. Two of the factors that affect the accuracy of the estimates are the estimation method used and the variability of the mineralization in the deposit. The objectives of the study are twofold: Firstly, to see how different estimation methods perform on a given deposit. Secondly, to determine the impact of particular nature of the mineralization on the results. The comparison of several estimation methods for the prediction accuracy is performed using the conditional simulation results as the basis.

Jan 1, 2000

By J. B. Hiskey, X. H. Jiang

The extraction of gold from chloride solutions by ion exchange is examined. It is shown that at initial gold concentrations between 1 - 5 ppm, 20 g/l C1- and pH 5, the kinetics of loading on weak base resins are slightly slower than those observed with activated charcoal. Equilibrium loading of auric chloride varies considerably as a function of pH from one resin to another. For all of the resins studied, nearly complete gold extraction was achieved between pH 2 and pH 6.5. Sodium hypochlorite was found to exhibit a slight effect on the equilibrium loading of gold chloride.

Jan 1, 1990

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By L. Franko, S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium circuits. In this study the performance of a continuous, laboratory wet-drum magnetic separator was evaluated with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration, and nonmagnetic materials. The results indicate that under certain conditions, the purity of the magnetic material increased after ultrasonic treatment.

Jan 1, 2001

By H. Y. Sohn, R. D. Hagni, M. K. Kojo

Reflected light microscopy was used to study the mineralogy and textures of experimental reactions of a nickel concentrate with a slag. Such an interaction is an important step in the bath smelting of nickel sulfide concentrate. Concentrate particles in the central portions of the pellets are rounded and develop vermicular SO2 gas porosity. In the outer portions of the pellets, the original minerals of the concentrate, pyrrhotite, pentlandite, pyrite, chalcopyrite, and violarite have agglomerated and reacted to form two intergrown phases: 1) pyrrhotite solid solution (Fe0.75Ni0.18Cu0.01S) and pentlandite solid solution (Fe0.58Ni0.51Cu0.03S). Magnetite formed euhedral crystals, skeletal crystals, and dendrites at the margins of the matte. Prismatic ferrohypersthene and octahedral Mg-Al-Fe spinel crystals and dendrites are present in the glassy slag.

Jan 1, 2001

By T. H. Eyde

Worldwide production of natural zeolites during 2001 was estimated to be about 3.5 Mt (3.85million st). Construction and agriculture continued to be the major consumers. Estimated production in North America during 2001, including the United States, Canada and Mexico, was about 40 kt (44,000 st). In the United States and Canada, the zeolitic tuffs are ground, extruded or modified for use as adsorbents, desiccants, ion-exchange media and carriers. In Mexico and the rest of the world, the zeolitic tuffs are cut into dimension stone that is used in construction. Zeolitic tuffs are usually composed of the minerals clinoptilolite, mordenite or both. They occur in a variety of colors and are easy to cut and shape. And they have low thermal conductivity. This construction application is classified with dimension stone rather than with chemical and agricultural uses.

Jan 1, 2002

By J. P. P. Silva

Sodium silicate (water glass) is a modifier reagent widely used in flotation with the function of a depressant or dispersant. The interaction between sodium silicate and mineral surfaces is still not well understood. This investigation aimed to illuminate the sodium silicate action mechanism as a depressant in the flotation of the minerals quartz and calcite. The experiments were done with high-purity mineral samples in the particle size range below 147 µm. The microflotation tests in a modified Hallimond tube showed that, in all systems tested, the efficiency of sodium silicate increased with the concentration. At concentrations above 1,500 g/t, almost total depression (96% for calcite and 97% for quartz) was achieved. The variation of sodium silicate modulus did not alter the quartz flotation performance in the presence of amine (150 g/t). The most efficient depression pH range was observed between 5 and 8. Above pH 10, the depressant action of sodium silicate was negligible. The infrared spectra obtained at pH 7 after silicate contact showed the presence of the groups OH and Si-OH, both suggesting that the adsorption of the neutral species Si(OH)4, as well as siloxane groups (Si-O-Si), attributed to adsorption of polymeric species. Sharing electron pairs is the proposed adsorption mechanism between Si(OH)4 and polymeric species and the surface sites (Si-O on quartz and Ca-O on calcite). At pH 11, the electrostatic repulsion prevents the species adsorption, impairing the sodium silicate action.

By R. J. Sweigard, R. V. Ramani

G.F. Learning The paper by R.V. Ramani and R.J. Sweigard is a wonderful description of the labyrinthine web that has been spun about the mining industry by energetic bureaucrats and politicians over the past 50 years. The remedy for the problem, however, is not more of the same, but less. That may be difficult for the industry to achieve, for it is not a technical solution but a political one. And the current fervor for more detailed planning at all levels of government and private enterprise has become deeply ingrained. The authors recommend the provision of more information about mining and mineral resources to "macro" (i.e., government) land use planners. They apparently overlook, however, the already strong tendency on the part of most government land use planners to consider themselves omniscient. Thus, giving them more information about the technical problems of mining will only make them want to get more and more involved in the "micro" (private, site specific) mine development and production plans of the individual mining firm. In fact, this has already happened at all levels of jurisdiction from municipal to federal government. Examples are legion. The most effective way to ameliorate the adverse impacts of government land use planning on existing and potential mining operations is to: (1) introduce greater flexibility in the definition of land use zones by local and state governments; (2) adopt realistic and relevant ambient environmental performance standards in governing relationships between mineral land uses and concurrent or subsequent nonmining land uses; (3) allow greater leeway for economic considerations in land use decisions in contrast to the explicit legalistic approach now in vogue; (4) recognize that all minerals are not the same and that sand and gravel mining should not be treated the same as underground metal mining, coal stripping, oil field production, or in situ leaching; and (5) eliminate the notion that mining operators should be responsible for determining in detail the use of land by subsequent owners of mined land. This last bit of conventional ethic really makes no more sense than requiring the builders of every shopping center or government office complex to provide detailed plans for the use of that land when its use for shopping or government is ended. Did the builder of Ebbetts Field plan for Brooklyn after the Dodgers went to Los Angeles? Should the developer of the Bingham Pit plan for suburban Salt Lake City after the copper mining goes to Chile? The nation's mining industry must address these questions before further bankrupting itself to provide more data to planners and spending thousands of dollars per acre to create land that when reclaimed is worth only a few hundred dollars per acre. Reply by R.V. Ramani and R.J. Sweigard We thank Mr. Leaming for his valuable contribution. His views on the problems of land use planning and mineral resources are most welcome additions to our paper. As the title indicates, our paper was more concerned with the impacts of land use planning on mineral resource conservation than with the details of the planning process. On the whole, his five recommendations would be helpful for mineral resource conservation. However, we would suggest that the argument he presents for his final recommendation does not address the differences between mining as a land use and commercial or institutional uses. We believe that this difference is the crux of the issue. We share Mr. Leaming's desire to ameliorate the adverse impacts of land use planning. Possibly the most detrimental impact is the loss of mineral resources. Any development, whether mineral or community, that does not give proper consideration to other resources can result in permanent loss or sterilization of resources. With proper planning, some of these losses can be avoided. As our paper indicated, one factor that limits the consideration of mineral resources, and ultimately leads to their sterilization, is the generally inadequate levels of resource characterization and understanding of the unique nature of mineral resources and mining operations. The last point raised by Mr. Leaming is also important. In terms of reclamation and land use planning in mining districts, we certainly do not advocate spending more than what the results are worth. The main thrust of the paper was to explore the avenues for conserving the mineral resources so that, at some appropriate time, the issue of mining and reclamation can still be addressed.

Jan 4, 1985

By Alex Stewart

Most iron bearing ores treated by the R=N Direct Reduction Process yield products lower in phosphorus than the initial ores. The sulfur is also removed and generally is in the range of 0.02 to 0.05 percent in the final R=N product, independent of the sulfur content of both the ore and carbon fuel used. The mechanism and thermodynamic justification of the principal reactions leading to the removal of both phosphorus and sulfur and the control of sulfur in the iron concentrate produced are discussed and supported by the results of laboratory experiments. In substantially all iron ores (containing up to 4% sulfur as sulfate) and solid carbon fuels (containing sulfur from 1 to 8%) tested, the rejection of sulfur has been in the order of 90-95%, with not more than 0.02 0.05% sulfur in the final metallic iron product. With respect to phosphorus-bearing iron ores ranging up to 0.70% P205, the rejection to tailings has been in the order of 70-95%, resulting in not more than 0.03 - 0.07% phosphorus in the final product.

Jan 1, 1958

By Richard H. Kennedy, G. A. Swanquist, John W. King, Frank F. McGinley, Dale C. Mathews, Hans H. Adler, E. C. Peterson, Ralph M. Wilde

INTRODUCTION From the first historical records of the discovery of uranium as an element and the attempted classification of its minerals in the early 18th century-through its first uses in pigmentation and the coloring of glasses and ceramic glazes-until 1939 when it was discovered that the isotope U235, was fissionable, uranium oxide in the form of pitchblende ores and concentrates (produced mainly in Bohemia, Canada, and the former Belgian Congo) in recent times was the source of uranium compounds incidental as byproducts to the recovery of radium from this invariable associated source. In 1938 this byproduct production from pitchblende concentrates was about 471 st of U3O8, with over 90% from Canada and the Belgian Congo and only 25.85 st from carnotite ores in the United States.1 Under the impetus of the Atomic Energy Commission's (AEC now part of the Energy Research Development Administration) domestic and foreign production incentives and buying programs, and as an initial assurance of atomic armament capability of the United States and the Free World, the growth of the uranium mining and milling industry burgeoned from 1952 to 1962. After a short period of decline, in the second decade and in large commitments beyond, it has again extended its capacity to meet ever-increasing fuel demands of atomic power generation by the electric utilities industry. In 1961 the peak production in the United States alone was 17,758 st of U3O8. Peak aggregate domestic and foreign deliveries of 34,581 st of U3O8 to the AEC occurred in 1960.z Canada's maximum delivery of 13,506 st of U308 was made in 1959. These peak and continued productions in the Free World are largely from: the Mesozoic (Jurassic) and Tertiary (Eocene) sandstones in the United States; the quartz pebble conglomerates of Canada and the Witwatersrand; pegmatites, Jurassic limestones, and Precambrian complexes, with less but significant production; the phosphoria, where byproduct production is minor. This uranium production in the form of precipitated concentrates has come from the milling of ores from these sources, both directly and by retreatment of gold cyanidation tailings on the Witwatersrand. Milling of crude ore has followed these processes: conventional crushing and size preparation, ore drying when required, salt roasting for high vanadium ores and byproduct vanadium recovery, carbonate or acid-leaching processes, classification sand-dine separations or countercurrent decantation (CCD) circuits and complete liquid-solids separations, resin-in-pulp (RIP) or liquid-liquid (solvent) ion-ex- change extractions, clarification of pregnant liquors, precipitation, filtration and washing, sodium and vanadium removals, and drying or roasting and packaging of the high-grade, high-purity uranium concentrate commonly referred to as "yellowcake." Coupled with the hazards and control of dust generation incident to conventional crushing and milling operations, more stringent control of airborne respirable and ingestible radioactive particulates and the protection of personnel against definitive external radiation are inherent to uranium milling. Impoundment and control of tailings and other effluents of uranium milling are more restrictive than in conventional practice, be- cause long-term disposal and containment of the uranium series of radionuclides, whether in solution or in solid form, are requisite to uranium milling and are made manadatory under regulatory agencies of government. 2. GEOLOGY AND MINERALOGY OF URANIUM Early Uses and Byproduct Production of Uranium Uranium was discovered by Klaproth in 1789 but had little commercial importance until the discovery of uranium fission by Hahn and Strassman at the close of 1938. The well-known uranium ores of Joachimsthal, Czechoslovakia, the Congo, and the Colorado Plateau were early sources of radium. Minor quantities of uranium were used for small-scale technical and industrial applications, particularly in coloring glass and ceramics, but most of the uranium was discarded. The Colorado ores were also mined later, chiefly for vanadium. Impetus of Armament Capability and Fuel Demands for Atomic Power Following the discovery of atomic fission, uranium became critically important for military applications and, more recently, as a nuclear fuel. Prior to 1966 uranium was acquired in the United States almost solely for use in the weapons program of the AEC. By 1970 the AEC had procured approximately 325,000 st of U3O8 from domestic and foreign sources. Current and future marketability is primarily dependent upon commercial demand for reactor fuel. Estimates of

Jan 1, 1985

By C. K. Blankenship

The competitive forces now driving the electric utility industry and the constraints of regulation at all levels are changing the way we will all do business now and into the next century. Utilities are using every technological tool at their disposal to find optimum solutions to challenges in every aspect of operations. In fuel planning and procurement, these tools include models that predict which dispatch line-up will comply with environmental regulations at minimum cost. This paper presents how those tools are being used for Duquesne Light Company.

Jan 1, 1995

By A. Zeni, S. L. Bessinger, T. A. Palm

San Juan Coal Company (SJCC) operates an underground coal mine near Farmington, New Mexico. Continuous miners and a longwall produce 7-8 million tons per year. The coal seam at SJCC has tested to have a propensity for spontaneous combustion. As such, during feasibility for this project, it was elected to utilize a bleederless ventilation system on the longwall. Three-entry gateroads are developed, and the longwall gob is sealed as mining progresses. SJCC utilizes a nitrogen injection system to continuously inertize the gob. In 2004, the mine was nearing completion of its first longwall district. The next district would contain longer panels (up to 12,500 feet). Due to the liberation of methane, and to a lesser extent hydrogen sulfide, a typical wrap-around ventilation system would not be appropriate. Not only would gas concentrations likely be challenging, but the overall ventilating pressure in the mine would have to be increased beyond limits established to mitigate the potential for spontaneous combustion. Given the above-described operating constraints, SJCC determined a need for a small ventilation shaft in the back (longwall setup area) of the next district that would draw adequate air past the longwall seals to maintain low gas levels and permit the required regulatory inspections to occur. Extensive ventilation modeling and gas desorption testing indicated that the shaft would be required to handle a volume of air ranging from 40,000 cfm to as high as 185,000 cfm. This large range is driven by the position of the longwall face with respect to the shaft and the effectiveness of the SJCC degasification program (SJCC uses vertical gob vent boreholes and horizontal in-seam methods). Ventilation simulations determined an appropriate diameter for the 350-ft-deep shaft to be 5 feet. Having determined shaft size, the next decision related to the method of shaft construction. Conventional shaft sinking was ruled out, due to the small diameter. Raise boring was an attractive option but had two drawbacks: (1) development crews would reach the bottom of the shaft just a few weeks before longwall startup, leaving a compressed timeframe to install the shaft, and (2) raiseboring requires additional underground entries to be developed to stow the project’s cuttings. While raiseboring remained a viable option, the problems associated with it led SJCC to also investigate blind drilling.

Jan 1, 2006

By Ray Brainard

Charleston Water System?s Daniel Island Extension Tunnel, initially thought to be the simplest of the four replacement tunnels to design and build, became the most challenging after the discovery of an unexpected 30-ft thick lens of sand in the normally consistent Cooper Marl while sinking a shaft on Daniel Island. This paper will explore the challenges involved with determining the extent of the unforeseen lens of sand, the accelerated boring program, and the redesign of the vertical alignment?keeping the alignment between the sand layer and the bottom of the Cooper River. It will describe how the challenges were overcome, and how the Owner, Engineer, and Contractor were able to team together to achieve the desired results.

By K. A. Natarajan, S. Usha Padukone

"An industrial waste liquor having high sulfate concentrations was subjected to biological treatment using the sulfate-reducing bacteria (SRB) Desulfovibrio desulfuricans. Toxicity levels of different sulfate, cobalt and nickel concentrations toward growth of the SRB with respect to biological sulfate reduction kinetics was initially established. Optimum sulfate concentration to promote SRB growth amounted to 0.8 - 1 g/L. The strain of D. desulfuricans used in this study initially tolerated up to 4 -5 g/L of sulfate or 50 mg/L of cobalt and nickel, while its tolerance could be further enhanced through adaptation by serial subculturing in the presence of increasing concentrations of sulfate, cobalt and nickel. From the waste liquor, more than 70% of sulfate and 95% of cobalt and nickel could be precipitated as sulfides, using a preadapted strain of D. desulfuricans. Probable mechanisms involving biological sulfide precipitation and metal adsorption onto precipitates and bacterial cells are discussed.IntroductionIndustrial effluents from hydrometallurgical and mineral processing operations often contain high sulfate and metal concentrations posing significant disposal problems, which require urgent solution to avoid serious environmental contamination. In such waste liquors, sulfate and heavy metals such as cobalt, nickel, zinc and iron originate from the chemical or biological oxidation of exposed sulfide minerals. Reduction of sulfate and precipitation of toxic metal ions from industrial wastes is essential from the viewpoint of environmentally acceptable waste disposal and recovery of associated strategic metals.Many of these heavy metals are essential for metabolic activity of bacterial cells at low levels. But they exert toxic effects at concentrations encountered in polluted water. Removal of toxic metals through biological reduction of sulfates from industrial waste waters have been practiced for several decades. Metal remediation through common physicochemical techniques such as oxidation-reduction, chemical precipitation, filtration, electrochemical treatment, evaporation, ion exchange and reverse osmosis processes is expensive and not suitable in the case of voluminous effluents containing complexing organic matter and low metal concentrations. Further, strong and contaminating reagents are used for desorption, resulting in toxic sludge and secondary environmental pollution. Biotechnological approaches can be more efficient and cost effective for detoxification of such effluents. Biotreatment/ bioremoval offers several advantages over conventional chemical and physical treatment technologies, especially for diluted and mixed contaminants. Biological detoxification, which involves the use of microbes to detoxify and degrade environmental contaminants, has received increasing attention in recent years (Iwamoto and Nasu, 2001). In addition, valuable metals can be recovered from metal sulfide sludge (Boonstra et al., 1999)."

Jan 1, 2015