Search Documents

By A. E. Jack Swanson, Brian P. Micke

INTRODUCTION Nevada Goldfields began underground mining development at the Kingston Project in September, 1986, followed by mill start-up in March, 1987. The first gold pour in April followed three years of preparatory work in establishing a North American operational base for the production of precious metals by Golconda Minerals N.L., an Australian mining firm. GENERAL CORPORATE BACKGROUND The Golconda Group of companies was established in early 1983 in Australia. It began operations by successfully retreating tailings at several old gold mining sites throughout Australia. With the limited reserves available for tailings retreatment, Golconda began to look toward the future by conducting a gold exploration program in Australia. However, the continued high price of gold in Australia had limited the possibilities of acquiring good properties at a reasonable cost and consideration was given to looking outside Australia in addition to Golconda's domestic exploration activities. North America was favored because of the proven potential for substantial gold deposits, the established infrastructure which would allow for rapid and cost-effective development of new projects and the advantages of similar political and economic climates. In mid-1984, Golconda established an office in California and began an extensive study of over 100 prospects throughout the United States. Two prospects were identified as a result of this study whch showed merit; one was located at Empire, Colorado and the other at Aurora, Nevada. Negotiations were then successfully undertaken to acquire these two properties. Golconda's U.S. offices were moved to Reno, Nevada in early 1985 to facilitate management of its projects. To operate and manage these projects, a small Canadian company listed on the Vancouver Stock Exchange, Cannon Minerals, was acquired by Golconda and renamed Nevada Goldfields Corporation. The current structure of the company is shown below in Figure 1. A private placement of 2,575,000 shares of common stock at US54.00 per share was arranged by Jacksons Limited of Australia in association with W.I. Carr (U.K.) Limited of London. This placement resulted in US510.3 million being available in May, 1986 for the acquisition and initial development of the Aurora and Empire projects. While the financing was underway, project planning commenced on both the Aurora and Empire projects. The Aurora project was selected as the one to be initially developed because of its relatively advanced stage of development. The

Jan 1, 1987

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese alloys are important raw materials for steelmaking. However, selective mining of high-grade manganese ore resources has resulted in a scarcity of these high-grade Mn ores (Mn: >42; Mn/Fe: >5). The present research work is carried out to explore a new smelting reduction process to produce high-Mn/Fe syntheticMn ore from low-grade ferruginous manganese ores. Representative samples of low-grade ores (Mn: 25–30%; Mn/Fe: ~1) were collected and smelting reduction studies were carried out using variable smelting power (20–30 kWh), carbon rate (10–20% of ore) and slag basicity (0.1–0.3) to produce high-MnO slag and manganese pig iron. Studies have shown that different-grade high-MnO slags (MnO: 38.57–58.24%; Mn/Fe: >15) and manganese pigs (Mn: 5.16–24%) can be produced at optimum process conditions. The high-MnO slag can be used as synthetic ore for the ferroalloy production process. The developed process is capable to effectively segregate the iron and manganese in the metal and slag, respectively. The optimum Mn and Fe separation (>95%) was achieved by smelting of 10 kg Mn ore batch in a 50-kVA electric arc furnace using 30 kWh smelting power and 0.16 kg of coke. The slag basicity was maintained at 0.3 and the optimum slag SiO2 was ~30%. The studies indicated that the upgrading of low-grade ferruginous manganese ores is a promising solution for achieving high-Mn/Fe-ratio synthetic ores for ferroalloy production. It can help the manganese alloy industry to overcome challenges associated with the scarcity of high-Mn/Fe-ratio Mn ores and efficient utilization of low-grade resources.

Aug 3, 2020

By Brian Fulcher

The Fort Lawton Parallel Tunnel was built in 1990 - 1991 by Morrison Knudsen Corporation (MK) as an integral part of Seattle METRO's planned expansion of the Westpoint Treatment Plant. The project included a concrete lined 2542 m (8,340 ft) long tunnel bored in sands and clays under the presence of methane gas and over 27.4 m (90 ft) of ground water table. The tunnel roughly paral¬lels an existing and still operating 3.65 m (12 ft) diameter tunnel originally completed in 1909. The parallel tunnel was constructed using a Lovat 4.72 m (15 ft-6 in) earth pressure balanced TBM with ribs and timber lagging as primary support. The tunnel alignment crossed under as much as 91.4 m (300 ft) of overburden as well as twin mainline railway tracks; terminating in a shaft adja¬cent to the Seattle ship canal. The project was completed in June, 1991 after a final "wet-tap" tie-in to the existing brick-lined sewer; over five months ahead of the contract schedule. This paper will describe the construction methods, job site conditions and difficulties encoun¬tered on this very challenging and successful project.

Jan 1, 1993

By D. J. M. Grodzian

Polymorphic transformations taking place in grinding processes, of massicot to litharge in PbO system, and of y to a in Fe203 system, were re-investigated. Grinding was carried-on in a steeel rotation mill charged with WC balls, under inert atmosphere. The kinetics of transformation in PbO was established by means of quantitative X-ray diffraction analysis. The resulting data fit a modified logistic growth function up to about 75% of transformed volume fraction, when a mixture at steady-state equilibrium is formed. The reasoning for the use of a modified logistic function is discussed. A sigmoidal growth function can be used if resulting data fit also an empirical power relationship between transformed volume fraction and time. However, it lacks the significance expressed by a modified logistic function. Assuming, the loss in magnetism is directly related to the amount of transformation in Fe 203, a quantitative analysis was performed using a magnetic balance method. The results fit only the modified logistic growth function, and transformation proceeds almost to completion. A wide literature survey of the subject is given. Available data from literature is compared with the results of the present study, and is shown also to fit a modified logistic grown function, with surprisingly similar slpes in a linear plot, independently of the material. The instrumentation effect on kinetics parameters, and the establishment of equilibrium mixture values, are discussed.

Jan 1, 1975

By J. O. Marsden, M. M. Botz

"Heap leaching is responsible for approximately 21 percent — 3.9 million metric tonnes — of copper production and 9 percent — 270 metric tonnes or 8.7 million ounces — of gold production worldwide. Given metal price assumptions of $2.25/lb for copper and $1,250/oz for gold, these portions of global production generate revenues of $19 billion and $11 billion, respectively. For heap leaching operations, small changes in metal extraction efficiency drive substantial changes in operating cash flow margins and affect project viability. Variances in actual metal production from budgetary forecast estimates can mean the difference between success (value creation) and failure (value destruction) for a heap leach project. Despite the importance of heap leaching for copper, gold and silver production worldwide, there are no clear standards or guidelines for developing heap leach metal production forecasts. There is considerable variation among copper and gold producers that apply heap leaching technology as to how such modeling and forecasting is applied at the operational level. There are a variety of different modeling approaches that can be utilized for this purpose. However, these vary in cost, complexity, time to implement, accuracy and credibility. This paper explores the options available for heap leach modeling, discusses the advantages and disadvantages of each approach, and provides guidelines/recommendations for an effective approach to modeling metal production at existing or planned heap leach operations. The paper also provides expected ranges of variation between actual and modeled production.Introduction and backgroundHeap leaching is fundamentally different from other methods used in the processing and extraction of gold, silver, and copper and other base metals. Considered globally, the technique represents a relatively modest portion of production compared with the primary technologies applied for copper and gold recovery. Approximately 21 percent of copper production is attributable to heap leaching techniques, as opposed to 79 percent by conventional crushing, milling, flotation, smelting and refining. For gold, about 9 percent of global production is obtained from heap leaching, compared with over 90 percent by various combinations of crushing, milling, gravity concentration, flotation and/or agitated cyanide leaching processes or, in the case of placer deposits, by direct gravity concentration and/or amalgamation. In cases where heap leaching is the primary source of metal production, the ability to accurately forecast metal production may be the difference between commercial success and failure for a project or operation. Heap leaching — of crushed or run-of-mine ore — is also commonly applied as a secondary process to treat lower-grade ores from a given deposit, such as at Chuquicamata in Chile, Cerro Verde in Peru and Bagdad in Arizona for copper extraction and at Twin Creeks and Carlin, both in Nevada, for gold. In such cases, heap leaching provides incremental revenue to supplement the primary process. Variances between actual and forecast metal production from heap leaching as a secondary process are typically tolerated and absorbed within the overall site metallurgical balance. In either case, accurate production modeling and forecasting creates significant value for heap leaching projects, is essential for managing production expectations — timing and volumes — and is likely to be a critical success factor for most heap leach projects."

Jan 1, 2017

By Erik A. Munroe, Nelia W. Dunbar, Virginia T. McLemore

In New Mexico, there are at least 100,000 abandoned mine waste rock piles with widely ranging geochemical and mineralogical compositions. A geochemical and mineralogical study was implemented for five waste rock piles, some which contained sulfides, in the Hillsborn Mining District. Chemical and physical characteristics of mineral grains and their secondary mineral oxidation rinds were examined with the electron microprobe. Pyrite and chalcopyrite appear to be the most reactive to oxidizing conditions. Clays, iron oxide, iron hydroxide, iron sulfate, and primary texture rinds exist in the waste rock piles analyzed.

Jan 1, 2000

By Jon Y. Kaneshiro, Stephen J. Navin, Jerry Ostberg

In 1968, the U.S. Bureau of Reclamation awarded S.S. Mullen Construction of Seattle, the Intake Tunnel (488 m by 4 m diameter tunnel) and Pumping Plant No. 1. In1998, the Southern Nevada Water Authority awarded Lake Mead Constructors (Kiewit of Omaha) a parallel New Intake Tunnel (518 m long by 4.6 m diameter tunnel) and Pumping Plant. Both projects provide water to a thirsty Las Vegas. This paper presents a detailed comparison of the two intake tunnels in terms of grout takes and pressures, geologic mapping and rock quality, grout penetration beyond the excavation line, degree of fracture grouting, and groundwater inflow boundary considerations. The paper provides a comparison of grouting techniques and material developments then and now.

Jan 1, 2001

By G. Deschenes, M. Fulton

The New Britannia Mine processes a qumtz-carbonate gold ore containing 4.63 git Au at a rate of 2,200 tpd. The ore contains approximately 3 .0% arsenopyrite, 2. 7% pyrite and the rest is gangue minerals. Eight to ten percent of the gold is refractory to leaching. Two years ago, New Britannia Mine experienced cyanidation problems. Gold extraction was not stable and occasionally decreased significantly. Preliminary test work, at laboratory scale and in the plant, indicated that lead nitrate addition was beneficial. A laboratory study was initiated to evaluate the level of control of the parmneters (grinding size, dissolved oxygen, pH, free cyanide and lead nitrate) to optimize the efficiency of the process. It was found that lead nitrate addition is required to alleviate the effect of metallic sulphides. This addition causes a significant increase in the gold leaching kinetics and a reduction in the cyanide consumption. The optimum system appeared to be: leaching for 24-30 hours at pH 11.8, 50 git lead nitrate, 250 ppm NaCN and 8 ppm 02. The gold extraction was 89.8% with grinding at 89%-74Fm (leached tail at 0.48 git). Cyanide and lime consumption are 0.40 kglt NaCN and 1.9 kglt respectively. Following the incorporation of lead nitrate, overall gold extraction was increased from 89.2% to 91.1 % but no change was noticed in cyanide consumption. The gross profit is $CDN 988,000 per year.

Jan 1, 1999

By J. A. Brierley, S. N. McIntosh, C. L. Brierley, E. G. Baglin, E. G. Noble, D. L. Lampshire

The U.S. Bureau of Mines investigated column bioleaching as a means of recovering manganese from a domestic low-grade oxide ore. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms and molasses as the nutrient source. The effects of medium flow rate, molasses concentration, and frequency of medium replacement on the rate of manganese extraction were examined. Results showed that flow rates between 0.4 and 8.1 L/min/m2 had little impact on manganese extraction, while an increase in the total amount of molasses applied during leaching directly affected the extent and rate of manganese extraction. Manganese extractions of more than 90% were achieved in 12 weeks of bioleaching in column tests using 500 g charges of ore. Sugar utilization by the microorganisms and formation of organic acid metabolites were monitored by high performance liquid chromatography (HPLC). Two methods were evaluated to recover manganese from the sugar- depleted bioleaching medium: (1) adsorption onto weak cation exchange resin, followed by stripping and precipitation techniques; and (2) direct precipitation of the manganese as MnCO, using ammonium carbonate. Both recovery methods removed at least 95% of the solubilized manganese from the medium as a carbonate salt. The stripped molasses medium was replenished with fresh molasses and recycled back through the bioleach column, successfully leaching more manganese.

Jan 1, 1993

By Levent Ozdemir, Gerald Dollinger

An extensive series of linear and rotary cutting tests were run in soft and medium strength rocks at the Earth Mechanics Institute of the Colorado School of Mines to investigate the possibility of very high speed mechanical excavation for tunnel, raise, and shaft boring. The results of these tests demonstrate that cutter penetrations of 38.1 mm (1.5 inch) and cut spacings up to 228.6 mm (9 inch) are possible in such rock without exceeding the bearing capabilities of the cutters. It was also demonstrated in vertical boring tests that continuous excavation rates up to 38.1 m/hr (125 ft/hr) can be achieved with state-of-the-art technology provided sufficient thrust and torque is available. A predictor model for soft rocks was also developed using the test data. Analysis of this model shows that the errors between the predicted and observed cutter normal loads appear to be independent of cutter diameter, tip width, cut spacing, and depth of penetration. This suggests that the structure of the model is correct with respect to these variables. An analysis of the coefficients in the model was also made and a correlation found between the principal coefficient and Unconfined Compressive Strength. The second coefficient in the model was found to be similar in magnitude to rock properties such as Brazilian Tensile Strength, Shear Strength and Point Load Index.

Jan 1, 1989

By Y. Lv, H. Ye, D. Du

Electrolytic manganese residue (EMR) is a kind of industrial solid waste with high silicon content that contains harmful metal elements such as chromium (Cr), copper (Cu), lead (Pb), cadmium (Cd), nickel (Ni) and cobalt (Co). Developing a highly effective and environmentally friendly process to treat EMR is important, both for the reutilization of metal resources and for environmental sustainability. In this study, the bioleaching of available silicon from EMR using silicate bacteria is investigated, with flask experiments conducted to optimize the parameters in the bioleaching system. For metal ions, the concentrations of manganese (Mn), Co, Ni and Pb in solution were measured to determine the environmental safety effects before and after bioleaching. The results show that the bioleaching rates of available silicon in the slag were mainly affected by the temperature, pH and pulp density. Under the optimal conditions of temperature of 30 °C, pH of 7.0, pulp density of 5 percent, shake flask rotational speed of approximately 210 rpm, particle size of approximately 0.150 mm and leaching time of 16 d, the concentrations of available silicon in the bioleaching system rose to approximately 110 to 140 mg/L. The metals remaining in the residues were mainly bonded in stable fractions, with concentrations lower in the leachate after bioleaching. This study demonstrates that silicate bacteria can be used to increase the contents of available silicon from EMR, and that bioleaching technology can realize the harmless resource utilization of EMR.

By Brian P. Canning

Ion exchange resin processes are receiving renewed attention in the mining industry for recovery;, of metals from solution. This interest has been inspired by the development of continuous countercurrent ion; exchange systems (CCIX) which are of much lower cost than the original, fixed bed contactor processes. With the countercurrent systems and new developments to process or upgrade the eluate product, ion exchange can now compete successfully with solvent extraction for treatment of uranium ores. The low concentration of U308 obtained in the CCIX strong eluate is generally upgraded by solvent extraction methods in sulfuric acid systems. Resin loadings of up to 120 grams per liter of U308, however, have been produced experimentally by recycling of eluate (HIM-IX process) and further developments may be expected in the near future. New developments in resin technology are bringing forth products of greater strength, loading capacity, selectivity and density. Densities up, to 1.35 spgr have been claimed by some suppliers. The process is not a new one and has taken years to advance to the present state of development. The earliest system to gain widespread acceptance was the resin-in-pulp system applied to uranium recovery. Ion exchange, however, later lost acceptance in favor of solvent extraction in the 1960's due to problems in resin degradation, resin contamination and resin-pulp separation, in addition to the development of improved solvent extraction reagents and techniques. The resin-in-pulp system continues to have application on high clay ores and has advanced in design. A number of other continuous ion exchange systems were also tried but never gained continued acceptance. In the current resurgence period the CCIX systems to gain acceptance were the Utah and Chem-Sep (Higgins Loop) systems. These processes are relatively simple in concept although require sophisticated controls. Fixed bed columns have also been designed into multistage systems in countercurrent operation but are not discussed in this paper. These systems remain competitive today for many applications. The most recent advancements however have been in the multistage contactors from,, which three are in current acceptance. These are the Himsley, Porter, and NIM systems. All industrial applications of these systems are relatively new, although pilot plant and in-plant development has been in progress over the last decade. Fur36ther developments should be expected in the near future.

Jan 1, 1979

By F. K. Letowski

Leaching of zinc sulphide concentrate by nitric acid which is simultaneously regenerated by oxygen in the reactive froth has been investigated. The reactive froth was formed by a recycled zinc sulphate electrolyte containing nitric acid, a mixture of gaseous 02 and NOx, entrapped in the foam and particles of the zinc concentrate suspended in the foam. In the reactive froth the multiple regeneration of nitric acid proceeded owing to the encapsulated oxygen and amount of nitric acid used can be considerably lower than in the continuous liquid phase. 93 to 97% of zinc was extracted to a solution containing 30 to 409/1 HNO, during 40 to 60 min of leaching in a batch reactor without regeneration of nitric acid. 50 to 100% of the consumed nitric acid was regenerated during continuous leaching in froth carried out in the ‘flotation column’-type reactor at 80 to 90°C and under pressure of 100 to 200kPa. The rate of HNO, regeneration in the froth was proportional to oxygen pressure and inversely proportional to nitric acid concentration in the froth. A two-stage process flowsheet is proposed. In the first, the reduction stage, removal of nitric acid from the leach solution directed to standard purification and electrolysis is carried out by its reduction to nitric oxide using fresh concentrate in the froth. In the second, the oxidation stage, nitric acid is continuously regenerated by oxygen in the froth.

Jan 1, 1995

By T. J. Lutz, J. L. Carr, J. A. Yonkey, C. C. Jobes

"Since 1984, the date of the first recorded fatality involving a remote controlled continuous mining machine, 38 miners in the United States have been killed when they were struck by a continuous mining machine. Proximity detection is a valuable tool for preventing fatalities, and the use of these systems is expected to significantly improve safety. Proximity detection provides a means to prevent accidents like these. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a series of underground tests to evaluate the accuracy and repeatability of proximity detection systems under a number of conditions such as varying the orientation and height of the personal wearable device (PWD), moving the PWD close to the trailing cable, and activating the machine’s mining mode. At the 2014 SME Annual Meeting, results from tests on first-generation proximity detection systems were presented. This paper will provide results from the similar tests performed with second-generation systems. The results show that performance has improved. For example, the negative impact of PWD orientation and the trailing cable has been reduced. However, some inconsistencies remain. Notably, performance changes dramatically when mining mode is activated. INTRODUCTION Since 1984 there have been 38 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM) [1]. In August 2011, the Mine Safety and Health Administration (MSHA) published a proposed regulation that would require proximity detection systems on all continuous mining machines except full-face machines [2]. Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHA-approved proximity detection systems are commercially available. MSHA estimates that of the 38 fatal striking and pinning accidents that have occurred since 1984 involving CMMs, the use of proximity detection could have been a preventative factor in at least 28 cases [1]. Furthermore, MSHA estimates that proximity detection could prevent 20% of all deaths throughout the industry [3]. NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system [4] and have recently conducted research intended to develop more advanced proximity detection technology for CMMs [5,6,7,8]. In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate [9,10] and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators [11,12]."

Jan 1, 2015

By S. G. Hardcastle, Akbar Sheikh

In Canadian underground uranium mines, bacterial leaching is being increasingly applied to low-grade ore reserves. At Denison Mines Limited uranium operations, old stopes are used as leaching vessels; these contain a leaching muck pile brought down by drilling and blasting from the back which contained a low-grade reef. The bacteria used require atmospheric oxygen to oxidize the pyritic ore. A study was initiated to evaluate the ventilation, including oxygen supply, specifically, of flood leaching stopes during their rest period. The method of ventilation investigated was a single ended compressed air system which feeds airlines laid under the muckpile and carried through the inlet pressure bulkhead. The air delivery system was tested for post- blast integrity with a sulphur hexafluoride, SF6, tracer gas technique. This was injected into the intake compressed air line and collected at the stope's borehole exhaust in grab-sampling bags. The samples were analyzed with a laboratory gas chromatograph and results provided information on the stope's airflow, average residence time, overall clearance time, volume of the airpath and the airflow distribution. The borehole exhaust was monitored by anemometer and psychrometer and indicated that the psychrometric conditions in the stope were independent of the area's ambient climate. Evaluation of the exhaust's standard gaseous composition showed the oxygen consumption of the bacteria to be independent of the investigated flow range. Field derived results are compared with computer models, theoretical predictions and laboratory investigations.

Jan 1, 1987

By M. S. Moats, A. Luyima, W. Cui

"Organic smoothing additives are used to produce dense, thick, high-quality cathodes in copper electrowinning. Glue had been used traditionally and is still used in operations that do not employ solvent extraction to produce the electrowinning electrolyte. With the advent of solvent extraction–electrowinning, guar started to be used and remained in use for many years as it does not affect the phase disengagement in solvent extraction. Recently, however, guar has been replaced by less-expensive saccharide- and polyacrylamide-based additives. This paper is the first of a series of four papers that examine saccharides and polyacrylamides as new additives for copper electrowinning. A review of previous research related to copper electrowinning additives is presented here, along with a selected review of additives in other copper electrodeposition systems.IntroductionThe recovery of copper from solution by electrowinning was first practiced in the early 1900s, but it was the combination of solvent extraction with electrowinning (SX-EW) in March 1968 at the Ranchers Bluebird Mine (Kordosky, 1992) that changed the landscape for the electrowinning process. Most copper electrowinning capacity is now associated with solvent extraction, though some copper is still won directly from leach solutions (Robinson et al., 2013). The ability to produce high-purity copper cathodes from SX-EW has taken the continued improvement of SX-EW technology over the past more than 40 years.One of the technologies that has seen improvement is that of the organic smoothing agents used during the electrodeposition of copper in the tankhouse. These organic additives are added to the acidic copper sulfate electrolyte during electrowinning to improve the smoothness, brightness and density of the copper cathodes. The organic additives that are presently in use are different from those used in 1999 (Jenkins et al., 1999). Over the past decade, many tankhouses have replaced the use of guar-based organic additives with those derived from other saccharides. Until now, there has been no comprehensive publication in the open literature on the behavior of these additives during copper electrowinning."

Jan 1, 2016

The 26th international APCOM symposium, hosted by The Pennsylvania State University, was held Sept. 16 to 20, 1996 in University Park, PA. Conducted about every 18 months throughout the world, APCOM symposia focus on the Application of Computers and Operations Research in the Mineral Industry. The APCOM International Council is the governing body of the symposia and determines the symposium’s locations and sponsorships. This group is composed of the nine permanent (voting) members. They include the University of Arizona, Colorado School of Mines, Pennsylvania State University, Society for Mining, Metallurgy and Exploration, Inc., Canadian Institute of Mining, Metallurgy and Petroleum, South African Institute of Mining and Metallurgy, Technical University of Berlin, Institution of Mining and Metallurgy and Australasian Institute of Mining and Metallurgy. The three nonvoting members are Moscow Mining Institute, China Institute of Mining and Rudarski Mining Institute of Slovenia.

Jan 1, 1996

"?irovski Vrh" Uranium deposit in Slovenia is type of mineralized sediments in ore bearing belts of deflected S-structure, in which the belt is less than 25% mineralized. Ore bodies of irregular small thickness, unreliably contoured, made difficult estimation of correct contours, which are necessary for design and exploitation works. The deposit was explored by vertical boreholes made at the surface and by boreholes fanned from drives. For the purpose of application of this estimation method, 1 m composites have been made in slices which were parallel to the referential belt plane. Estimation was made for 1,5m x 1,5m x lm blocks which do correspond to the size of the containers in the ore transport stage. Two variables have been used: the first, indicator of function (ore=1, waste material =0) and kriging method; the second, logarithmical content of Uranium and Minimum Mean Square Error Estimation (MMSEE) method. Based on estimated values of those variables, probability of ore quantity as well as Uranium content over determined cut-off were calculated for each block. Those two parameters enable determination of the most probable form of the ore body in ecah one metter slice. Estimation of sixteen small blocks in a large 1,5m x 1,5m x 1m block made possible estimation of ore quantity and its content for the determined cut-off, as well as categorization of exploration. This method is being used for estimation of ore reserves and planning of exploration operations. The described' methodology was tested in an exploitation block.

Jan 1, 1986

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By Scott Ellenbecker

Mining has evolved in recent years, taking steps forward in the way that the industry is considerate of the environment and the communities in which it operates. Technology plays a major role in that evolution. Osisko Mining?s Osisko Mine near Malartic, Quebec is developing a new way of doing business. One manager said, ?We are building the Osisko culture,? but the company is doing many things that could become industry changers. Much of the change is driven by mine ownership and management to offer a better workplace and better community relations. Mining equipment manufacturers are changing, too, by engineering products with more operator comfort, fuel economy, ease of maintenance and more cleanly designed machines. And for those drills working close to communities, smaller bore sizes and sound retention are just two changes for the better.

Jan 1, 2012