Search Documents

By R. Rodgers

The Pinto Valley Concentrator of BHP Copper Inc. restarted its sulphide mining operations in September 2007 to produce copper and moly concentrates. During the plant production ramp up, the copper/moly circuit quickly reached the copper grade and recovery targets, but the production and quality of the moly concentrate continued to be a challenge. Even though several improvements in the moly circuit were completed, the final moly concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns was chosen. The column design and construction were done utilizing in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing moly concentrate to the required specifications, that is, high moly tenors and low copper and iron content. In this paper, the operating parameters, mass balance, design, installation, commissioning and operation of the new flotation columns will be discussed.

Jan 1, 2010

By Takuji Yamamoto

High-speed TBM excavation requires rapid ground assessment ahead of excavation, particularly in complex grounds. The Tunnel Reflector Tracing technology (TRT) developed by authors, uses seismic reflections to produce volumetric images of ground anomalies. To further minimize interruption in the TBM excavation the authors modified surveying technique switching from cable (wired) to radio (wireless) data acquisition system. This paper presents the outline of the Wireless TRT system, and compares the results for the wired and the wireless surveys. The comparison shows that the wireless system offers high precision data, is more efficient and economical and significantly less intrusive in tunneling operations.

By Nicholas T. Esposito

An advanced coal preparation plant has been built at Homer City, Pennsylvania, by Pennsylvania Electric Company, a subsidiary of General Public Utilities Corporation, and New York State Electric and Gas Corporation, as an alternative to utilizing flue gas desulfurization technology to meet the Federal Environmental Protection Agency and the Pennsylvania Department of Environmental Resources air quality emission regulations of 4.0 lb S02/106BTU for the two (2) existing coal-fired generating station Units No. 1 and No. 2, and a 1.2 lb S02/106BTU for the new Unit No. 3. The coal preparation plant is designed to process 5,200,000 tons of run of the mine coal annually and has a design capability to process 1,200 tons per hour via two (2) equal capacity 600 tons per hour preparation circuits.- The plant is designed to produce multi-product coal streams consisting of a middling product of medium ash and medium sulphur content, which is environmentally compatible to support operation of the two (2) existing generating Units I and 2, and a deep cleaned, low ash, low sulphur coal product capable of environmentally supporting the ambient air quality requirements of the new Unit 3 generating facility. The waste product from the process consists of high ash, high sulphur reject material. The process has the acronym MCCS (Multi-Stream Coal Cleaning System).

Jan 1, 1982

By A. D. Davis

The former Homestake gold mine at Lead, South Dakota, has been selected by the National Science Foundation as the proposed host site for the Deep Underground Science and Engineering Laboratory. The deep laboratory and associated research campus will be developed at approximately the 7700-ft level. Plans also include the development of the Sanford Underground Science and Engineering Laboratory at the 4850-ft level. After the mine?s pumps were shut off in June, 2003, water levels rose to approximately the 4650-ft level by early 2008. Pumps in the 8150-ft deep mine were turned on again for dewatering in April, 2008. Instrumentation is being installed in the mine to measure water-level declines during pumping, for later analysis of permeability and related hydraulic properties of the formation. Pressure-sensitive transducers and data loggers will provide real-time information on water levels that will be available to interested parties. Quality of the water also will be monitored as it is pumped from the mine. I

Jan 1, 2009

By Ronald E. Heuer

A 1995 RETC paper of similar title presented a method for estimating rock tunnel water inflow based on semi-empirical correlations with borehole water pressure tests. Since that time the author has found the method to be very useful, and it has been used by others in the industry. This current paper is an update which is intended to: A. More clearly explain assumptions and limitations of the method. B. Describe some case history examples. C. Respond to questions which have been raised; and extend the method to other considerations including distribution of inflow along the tunnel, panning requirements, interpretation of tunnel probe hole water inflow, and estimation of potential effectiveness of pre-excavation grouting to reduce water inflow.

Jan 1, 2005

This geometallurgical study examines the gangue mineral variability at the Bingham Canyon porphyry copper mine in Utah. Understanding an orebody?s mineralogy is important for mine and mill planning because it provides information on the size, texture, and distribution of ore minerals, the relationship between ore and gangue minerals, and the extent and type of alteration. Quantification of the mineralogical variability and properties of an orebody provides valuable input to the ore model and may have a significant effect on recovery optimization. This study was designed to be carried out on an initially detailed scale in order to develop a robust methodology for measuring and quantifying specific parameters, such as the distribution of mineral phases, alteration assemblages and fractures from key ore domains at the Bingham Canyon mine (Figure 1). Details of the methodology are reported below. This technique can be applied to testing the impact of mineralogy on a number of processing parameters. [ ] Figure 1. Ore domain map of Bingham Canyon (Kennecott Utah Copper, 2003) showing the 33 geometallurgical ore domains. The samples for this study were collected from the northwest part of the deposit circled on the map. PROJECT BACKGROUND Geology The Bingham Canyon deposit is a large porphyry Cu-Mo-Au deposit with associated skarn and base-metal replacement deposits mined in an open-pit mine measuring about 2.5 miles across and 4,000 feet deep. The deposit is hosted by the Bingham Stock, a Late Eocene to Mid-Oligocene intrusive complex. The skarn is hosted by the Late Carboniferous-age Bingham Mine Formation, which is comprised of quartzites and basal limestones (Babcock Jr. et al., 1998). The Bingham Stock is a composite intrusive complex that was emplaced over a period of about two million years. The oldest phase is described as a fine-grained equigranular monzonite (MZ), which intruded the country rocks at 39.8 ± 0.4 Ma (U-Pb zircon TIMS age) (Parry et al., 2001). Subsequently, the quartz monzonite porphyry (QMP) was emplaced, followed by intrusion of a latite porphyry (LP). The final intrusive phase, which forms narrow dikes that crosscut the Bingham Stock, is represented by a quartz latite porphyry (QLP), which is dated to 37.5 ± 0.4 Ma by 40Ar/39Ar dating of sanidine (Deino and Keith, 1998). Also present, are a minette dike in contact with a QLP dike (Waite et al., 1998; Deino and Keith, 1998), and a biotite porphyry (BP), a quartz latite porphyry breccia (QLPbx), and a pebble dike (Redmond, 2002). The copper orebody is centered above the Bingham Stock and forms an inverted cup shape with three high-grade copper zones extending to depth. Molybdenite mineralization occurs within and extends below the copper orebody, but is not correlated with copper mineralization. The main sulfide assemblage is chalcopyrite, bornite, molybdenite, and pyrite. Gold is locally intergrown with chalcopyrite and bornite (Babcock Jr. et al., 1998; Phillips et al., 1998). The surrounding country rocks host skarn deposits with three main ore types - garnet skarns, massive sulfides, and iron oxides. The garnet skarns contain chalcopyrite and pyrite with magnetite veins. In the massive sulfides chalcopyrite and pyrite occur either in banded sulfides or in unconsolidated microbreccias. The iron oxides contain disseminated chalcopyrite with minor chalcocite and bornite (Harrison and Reid, 1998). The deposit is overprinted by several stages of alteration. Potassic alteration is concentrated at the center of the deposit. It is surrounded and partially overlapped by a propylitic alteration zone. Both zones are overprinted by sericitic alteration. In the northern part of the deposit evidence for argillic alteration can be found (Bowman et al., 1987). Similarly, the skarn deposit was also overprinted by several stages of alteration: wollastonite, idocrase, and garnet in cherty limestones, and quartz and diopside forming in calcareous quartzites. Distally, diopside was replaced by talc, tremolite, dolomite, secondary calcite, and pyrite, and quartz and sulfide veinlets with biotite and actinolite selvages are present. Andradite garnet, diopside, quartz, magnetite, hematite, and copper sulfides were overprinted by wollastonite (Babcock Jr. et al., 1998). Because the monzonite, quartz monzonite porphyry, latite porphyry, and quartz latite porphyry host the bulk of the mineralization, our research is focused on these lithologic units. Geometallurgy On the basis of geological (lithology, alteration assemblages, fracture density, copper mineralization) and metallurgical properties, the deposit has been divided into 33 ore domains by mine geologists and metallurgists (Figure 1). In map view, these domains cross geologically defined boundaries (MZ, QMP etc.). These domains reflect regions of the deposit that have particular, mapable attributes or properties. They reflect a combination of geological and mineralogical characteristics that combine to impact processing. Alteration, for example, as shown by talc mineralization, is one such key feature. Hardness may reflect the absence of sericitic but presence of potassic alteration. Structural discontinuities such as faulting, fracturing, or development of void

Jan 1, 2009

The state of the tunneling and underground construction industry and the advancements of the industry?s biggest machines were the main topics at the 2008 edition of the UCA of SME?s annual George A. Fox Conference. This year SME hosted more than 250 tunneling and under-ground construction professionals at the Graduate Center, City University of New York. During the morning session of the long-running one-day conference, attendees heard a state of the industry through the annual Home-town Update where it was evident that the industry is doing well. Michael McHugh of Moretrench cruised through the many projects that are under way along the Eastern seaboard of the United States and said he could have gone longer if time allowed. An example of how well things are going for the industry is a look at New York, where the industry is flourishing. The New York City Water Tunnel # 3 project is a $668 million project that was awarded to Schiavone/Shea/Frontier Kemper joint venture in 2004. McHugh said that mining on the project was completed in August 2006 and that all con-tract work is expected to be completed by August 2009. The Second Ave. Subway is a $337-million twin tunnel project that will connect upper Manhattan with the financial district. This is a four-phase project. McHugh said the Metropolitan Transit Authority obtained full funding in 2007 and construction awards will be awarded during the next two years. The No. 7 Line Flushing extension, a five-year, $1.15- billion project that will redevelop the Hudson Yards area of Midtown West and the New York City Water Tunnel No. 3 project is the largest capital construction project in New York City?s history. McHugh said the project was given notice to proceed on Dec. 13, 2007. The project includes three large shafts, two parallel 6.7 m (22 ft) tunnels at 2,000 liner m (6,500 liner ft), one large cross adit, one large underground rock cavern station with two interlocks and eight penetrations. These were just a few of projects mentioned in the Hometown Projects update.

Jan 1, 2008

By MATT RENAUD, Mustafa Kumral

As high-quality mineral deposits are thoroughly exploited, mines of the future will have to move towards more remote and lower quality projects. With these projects comes an increased business risk to the operator. Even now, mining companies often turn to foreign countries for new deposits to produce, introducing the concept of country risk into their portfolio. Furthermore, feasibility studies often fail to accurately quantify the risks associated with various projects, and as such, this study proposes a technique of risk quantification which can both aid mining companies to evaluate the viability of investment and assist in risk disclosure to public investors for the mining industry of the future. This paper aims to quantify the effects of country risk on the valuation of potential mining projects, using a combination of modular and risk-weighting techniques to evaluate the country risk premium (CRP) required to obtain capital for operation of risky foreign mining projects. The techniques proposed in this paper are demonstrated using fictional examples and then evaluated for accuracy against a recently developed debt-funded precious metal project in a country in the Americas.

Sep 30, 2021

By M. Haase

[ ] How important is a robust communications system for your mine site in order to meet operational and safety requirements? Do you currently have VSAT in place and need a low cost, high quality multi-line VoIP phone system at the site? By adding a single, compact piece of hardware, you can utilize your existing satellite internet connection and have as many as twenty-four separate phones lines from a single unit. The platform is scalable for any size of operation and can be implemented above or below ground.

Jan 1, 2012

By Gino Vogt

In mechanized tunnelling operations performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequate/ suboptimally dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water and polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole job. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer´s point of view.

Jun 13, 2021

By E. Snyders

Two alternative processes for the manufacturing of zircon products were investigated by the South African Nuclear Energy Corporation (Necsa). These were the synthesis of doped-zircon pigments from plasma dissociated zircon, and an upgrading process to convert an inferior grade of zircon into a superior opacifier for ceramic applications. A solid-state reaction process was used to produce doped-zircon pigments. The influence on the colour intensity of the pigments on a ceramic tile were compared for milled and un-milled plasma dissociated zircon (PDZ) material, prior to calcination. Pr-yellow and V-blue zircon pigments produced from PDZ with different degrees of dissociation, were also evaluated. The second zircon beneficiation process entails the upgrading of an inferior grade of zircon to a superior opacifier for ceramic applications. A calcining process in the presence of mineralizers was used to produce the product in a conventional muffle furnace. A pre-milled inferior grade zircon concentrate, with a relatively high iron and alumina content generally not suitable for high quality ceramic applications, was used in this study. The influence of the upgrading process on the opacifying properties of the zircon material was compared to that of commercially available prime grade zircon opacifier products currently being produced in South Africa. The influence of a calcining step in the presence of mineralizers with regard to the milling characteristics of the treated zircon material was also evaluated.

Jan 1, 2005

The authors summarise the development and recent advances in the reconstruction and visualisation of three-dimensional objects from point data and describe applications to the reconstruction of orebody shapes from drill-hole and other data. In particular, Dijkstra's algorithm is proposed and implemented as a means of optimal reconstruction of complex orebody and topographical shapes from irregularly located sample data. The surfaces of the shapes are constructed from triangular tiles and the algorithms proposed by the authors are guaranteed to find the optimal set of tiles that "best" construct the surfaces on the basis of specified objective criteria. The algorithms are illustrated by applications to a complex silver/gold/zinc/lead deposit.

Jan 1, 2002

By B. Li

"Sepiolite is a magnesium-rich, porous, and fibrous clay mineral with broad applications. These applications take advantage of sepiolite’s high specific surface area and unique nano-sized channel structure. Over the past years, numerous materials and techniques based on the structure and property of sepiolite have been developed. This article reviewed the recent achievements in developments and applications of sepiolite in environmental protection, catalysis area, and nanocomposites. The prospectives of sepiolite applications is also discussed. INTRODUCTION Sepiolite is a magnesium-rich, porous, and fibrous clay mineral. The typical chemical formula of sepiolite is Si12Mg8O30[OH]4[OH2]4·8H2O [1]. Sepiolite has a high specific surface area and nano-sized channels because of its special structure [2]. This unusual crystal structure projected onto the [001] plane is shown in Fig.1 [3]. As it can be seen, silicon and oxygen atoms make up for the tetrahedral structure and magnesium and oxygen atoms form octahedral structure, respectively. Those tetrahedral-octahedral-tetrahedral ribbons expand boundlessly in one direction, leading to the special fibrous structure of the sepiolite. Every tetrahedral-octahedral-tetrahedral ribbon is combined to the next by an inverted Si–O–Si bond, which causes an interlaced layer with a continuous tetrahedral sheet and a discontinuous octahedral sheet. Terminal MgO at the edges of the ribbons is coordinated with two structural water molecules, which can form hydrogen bonds with zeolitic water molecules that are located in the channels running parallel to the fiber axis [3,4]. The Mg2+ ions inside the channels can be exchanged with other cations in solution. Therefore, sepiolite can be used to remove metal cations from aqueous solutions [5,6].It can be seen from Figure. 1 and Table 1 [7], the unique structure endows sepiolite with a substantial surface area and nanoscale channels. Its specific surface area reaches 320 m2/g and channel dimensions up to 3.7×10.6 Å. There are three active adsorption sites on the surface of sepiolite: one is oxygen atoms of the Si-O tetrahedron. The second is the structural water molecules paired with magnesium ions at the edges of the ribbons, which can form hydrogen bond with adsorbent. The last one is the Si-OH groups due to the breaks of the Si-O-Si bonds on the surface of Si-O tetrahedron. Thus, sepiolite has strong adsorption ability which has been widely used in environmental protection. Moreover, sepiolite has many significant features such as good mechanical and thermal stability, rheological property, porous, and easily modification, making it be a hotspot in chemical and biological researches. However, with the development of technology, broader and more advanced applications of sepiolite have been carried out in recent years. In this study, the recent achievement in sepiolite applications is summarized, the further tendency is also discussed."

Jan 1, 2018

By Mike Moody

"No matter what type of ore is being extracted from a mine, mucking with front loaders can be accompanied by wet fines that cling to every surface. Once loaded into a hopper or conveyer transfer chute, viscous material can quickly build up on the walls to create bottlenecks, clogging the chute and causing expensive downtime.Clearing material from hoppers, chutes, bins and vessels can be done using manpower and tools on hand, but safety experts recommend considering a solution that prevents exposing workers to potential hazards. Operators at modern mining sites, such as the Eagle Mine, located in Western Marquette County of Michigan’s Upper Peninsula, understand that using specialized equipment reduces worker exposure, offers the safest mode of production and provides the most cost-effective lasting results.“Safety is a top priority for us,” said Ted Lakomowski, lead reliability technician at the Eagle Mine. “When we experienced clogging and downtime at the processing mill, the crew naturally swung into action to resolve it, but we immediately sought a safer long-term solution.”Stope mining for nickel and copperOwned by Lundin Mining, a globally diversified base metals mining company headquartered in Toronto, ON, Canada, the Eagle Mine is the only primary nickel mine in the United States, producing 1.5 percent of the world’s total nickel production. The first operation permitted under Michigan’s Part 632 Non-Ferrous Mineral Mining Law, it opened in 2014 and is expected to produce 163 kt (360 million lbs) of nickel, 134 kt (295 million lbs) of copper and small amounts of other metals over its estimated nine-year lifespan.The company extracts approximately 2 kt/d (2,200 stpd) from the underground nickelcopper mine using a bench-and-fill stoping process. Accessed from the surface by specialized underground trucks, the vehicles carry about 45,400-kg (100,000-lb) loads through a 1.6-km (1- mile) long and 5.4-m (18-ft) diameter ramp shaft descending into the earth at a 13 percent grade. Stoping is a bottom-up method that involves systematically blasting columns of loosened ore that is then mucked by front loaders into trucks and backfilled using cemented and uncemented rockfill."

Aug 1, 2019

The Virginia Center for Coal and Energy Research has been developing models of wireless signal propagation in underground coal mines since 2007. The current mine propagation modeling software, named COMMS, is able to locate potential broadcast points for underground wireless mesh systems and estimate their coverage. COMMS utilizes programmed routines to calculate necessary values to both quantitatively and qualitatively solve and analyze predicted coverage areas. The program approximates the spatial relationships that are encountered, such as ventilation regulators, belts and other obstructions. Using this model for propagation allows the optimal communications node locations to be calculated, by using lessons learned from current installations and experience with the new technology. In addition, the optimization can be calculated by checking all possible combinations of broadcast locations. This paper compares these optimization calculation methods. The ability to solve a mine?s communication network provides a pre-installation mine network design map, creates coverage maps of the mine and allows planning for future communication activities

Jan 1, 2011

By Donald O. Rausch, William E. Hawkes, Odin Jr. Strandberg

INTRODUCTION Kennecott Copper Corp.'s Tintic Div. Burgin mine is a 725 t/d (800 stpd) lead-zinc producer, located in the east Tintic mining district, 5.6 km (3.5 miles) east of Eureka, and 130 km (80 miles) south of Salt Lake City, UT. The Burgin mining complex includes three shafts, shop, dry, and office facilities, and a 454 t/d (500 stpd) flotation concentrator. Production and ser¬vice entry to the mine is through a 4.26-m (14-ft) diam concrete-lined production shaft, and a three-compart¬ment rectangular shaft. A connection with the Apex No. 2 shaft and the Burgin mine provides a second exhaust airway. Bear Creek Mining Co., Kennecott's exploration sub¬sidiary, began exploration of the Burgin mine area in 1957 with the sinking of the 335 m (1100 ft) deep No. 1 shaft. A station was cut at the 320-m (1050-ft) level of the shaft and extensive drifting, diamond drilling, and some winzing and raising confirmed the presence of a major lead-zinc ore body, the main portion of which oc¬curred below a hot saline water table. Surface facilities and the 4.26-m (14-ft) diam concrete-lined production shaft were completed in 1966. Ore production has been steadily increased to 725 t/ d (800 stpd) since 1966. The collar elevation of the No. 2 production shaft is 1731 m (5678 ft) above sea level. The mine's three levels, the 1050, 1200, and 1300 are at elevations of 1414.6, 1356.4, and 1338.1 m (4587, 4450, and 4390 ft), respectively. The approximate elevation of the hot saline water table is 1382.6 m (4536 ft). The earliest production on the east Tintic mining district was from the Eureka Lilly mine in 1909. Later, in 1916, the Tintic Standard mine was discovered, and pro¬duced ores with a gross value of $80,000,000 through 1956. The Eureka Standard mine located 1.6 km (1 mile) southwest of the Burgin mine produced ore worth $12,000,000 from fissures in the Tintic quartzite along the Eureka Standard fault. Ores produced from the east Tintic mining district through 1971 are valued at $151.3 million. The production from the entire Tintic district is approximately $500 million. GEOLOGY The Burgin ore deposit occurs as replacement bodies in limestone, dolomite, and shale. Numerous fault struc¬tures and rock formations make the mine geology com¬plex. The mineralization is strongly associated with sev¬eral major geological features, which include the Ophir formation, consisting of limestone, dolomite, and shale as the favorable host rock, and the structural influence of the east Tintic thrust, the Eureka Standard and sev¬eral other significant faults. Fig. 1 depicts the Burgin 1300 level workings, a generalized configuration of the ore body, and the main geological features. Covering the quartzite, limestone, dolomite, and shale facies enclosing the Burgin ore deposit are 183 to 274 m (600 to 900 ft) of andesite. The Burgin ore consists of massive sulfide and oxide lead-zinc ores with significant silver and cadmium val¬ues. The main ore minerals are galena, cerrusite, and spalerite. Extensive manganese oxide deposits are associated with the lead-zinc ore occurrence. A limited

Jan 1, 1982

By T. J. Crebs

The latest estimates compiled by the Society of Exploration Geophysicists again indicate a moderate increase in mining geophysical activity in 1980 over the 1979 level. While North American activity remained at above the 1979 level, a considerable increase in mining geophysics was reported in South America, Australia, and the Far East. The total worldwide expenditures for mining geophysics were reported to be $53.7 million in 1980, compared to $44.4 million in 1979, and $31.6 million in 1978. During 1980, approximately 2% of all dollars spent on geophysics were attributed to mining geophysical activities; this percentage has remained relatively constant in recent years. Airborne surveys accounted for 51% of the total worldwide mining geophysical expenditure, 43% was spent for land surveys, and 6% for borehole surveys. Within the US, the breakdown of expenditures for land surveys was 60% for elec¬trical methods, 23% for gravity and magnetic methods, and 17% for seismic techniques. Electrical techniques remain the primary exploration tool for US mining geophysicists. Electrical Methods With inductive or electromagnetic (EM) techniques, significant developments were achieved in both frequency-domain and time-domain systems. Work continued on increasing the signal level on most time-domain (TEM) methods, to increase the exploration depth. The Crone group increased the power of its Pulse ElectroMagnetic system (PEM) to a 20-amp transmitter-loop capability. The GEOEX group is modifying the SIROTEM II system to obtain larger transmitter amperage from a portable motor generator. Geonics developed a new digital recording system (data logger) for its EM-37 system. This development should increase the productivity of EM-37 crews. A new ground, frequency-domain EM system was developed by the Scintrex group. This novel Genie system does not require a wire link between the receiver and transmitter. Because an amplitude-ratio is measured, the Genie data are reported to be relatively insensitive to coil orientation and distance errors. This new technique does not need extensive line-cutting or accurate station-chaining and would appear to be a good reconnaissance instrument. Scintrex also began marketing the new IPR-11 induced polarization spectral receiver. This receiver is microprocessor controlled, and can output to a cassette tape and record 10 windows of secondary voltage decay simultaneously from up to six receiver dipoles. The Phoenix group's new 100 kW induced polarization/resistivity (IP/R) transmitter began tests using their IPV-3 multifrequency, multichannel receiver. While this unit was primarily developed for "oilfield" IP exploration research, it has obvious application to "deep" mineral exploration. The Phoenix group also developed a new remote-reference, real-time magneto-telluric (MT) device in 1981. This five-component MT sys¬tem has a frequency range from 0.0005-384 Hz. Helicopter-borne electromagnetic (HEM) developments also continued in 1981. The mining in¬dustry increased its use of the new Geonics EM-33-3 multifrequency, multicoil instrument. In 1981, the Dighem group developed software for estimating magnetite as a mapping parameter from its HEM system. Dighem's work is said to complement airborne magnetic intensity surveys, since the HEM estimate is independent of remanent magnetism and magnetic latitude effects. Gravity and Magnetic Methods Probably one of the most innovative techniques in geophysics in 1981 was the use of airborne gravity surveys for both mining and petroleum exploration. The Carson group is using a modified, shipborne LaCoste-Romberg platform in helicopters. Data accuracies to 0.5 milligal have been achieved by flying gridded surveys. Although this airborne method is expensive-up to $186/ km ($300/line-mile)-the geophysical community has been excited by initial results. On the ground, the portable proton-precession magnetometers are becoming sophisticated. Both GeoMetrics and EDA recently introduced field magnetometers having data storage and processing capabilities. This development should greatly increase the productivity of ground-magnetic surveys. Seismic Methods Development of high-resolution seismic techniques continued in 1981. These techniques have primarily been directed toward coal studies for fault detection. OYO Instruments introduced their McSEIS-1500 seismic data acquisition system in 1981. This device contains a 24-channel recording capability, with digital output to 256-kbyte floppy disks. The high-speed data transfer using the disk media is considered a desirable feature. Borehole Methods The general decrease in uranium exploration, where borehole logging is extensively used, probbly led to the overall decline of geophysical logging activity in the minerals industry. However, a number of new sondes and logging systems were introduced in 1981: • Mount Sopris recently introduced their Series III logging system. This microprocessor-controlled unit records up to four channels of data on nine-track or cassette magnetic tape. The logging package is relatively light-weight, so helicopter transport to mountainous or roadless exploration sites is possible. (Both the Edcon and Woodware-Clyde consulting groups offer "slinging" capabilities for their Mount Sopris units.) Mount Sopris is continuing work on their 500-mm-diam (2¬in-diam) spectral gamma-ray sonde. This tool is expected to be available soon. • Owl Technical "slim-downed" its successful digital deviation probe to 380-mm (1.5-in) outside diameter. This new sonde will also measure inclinations up to 80° from the vertical, as compared with its older instrument that could measure inclinations to 30°. • A magnetic susceptibility sonde was introduced in the US by the OYO Instruments group. This Kappalog sonde contains two aircored coils for measurements slightly affected by thermal changes within the borehole. The increased activity in massive-sulfide exploration and the need to "look" deeper no

Jan 5, 1982

By Bob Gordon, Allen Furth, Dan Dobbels

A 4.8 m (16 ft) diameter hard rock tunnel was driven through granite bedrock to create the 1.7 kilometer (1.1 mile) long Hampton McCloy Retention Tunnel for the city of Richmond, Virginia. During the work the tunnel encountered narrow seams of partially decomposed granite that were not self supporting and could be dealt with using ribs and lagging. However, as the tunnel approached the receiving shaft, it encountered a large seam of highly decomposed rock, alluvial deposits and running sand which resulted in soil loss into the machine. As a result of this condition, a jet grouting program was quickly developed to allow the tunneling to continue. This paper will describe the manner in which jet grouting was used to solidify and stabilize the decomposed bedrock, alluvial soils, and running sand to allow the TBM to continue tunneling.

Jan 1, 2003

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By M. H. Pettibone

During the past decade, the size of grin- ding mills has steadily increased. Mills 11 m in diameter with 9 mW motors have been installed with even larger units on the drawing board. The rising costs of energy and labor have spurred interest in improving efficiency while reducing capital investment and operating labor. Autogenous and semiautogenous grinding have experienced renewed interest as efforts to reduce operating and capital costs have increased.

Jan 1, 1981