Search Documents

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By B. J. Arnold

Coal blending inherently means homogenizing a mixture of coals so that the properties of the blend meet some specifications for maintaining power plant performance and emission requirements. In practice, however, coal blending is, at best, coal mixing. The degree of blending sophistication required depends on the reason for coal blending in the first place. If it is to maintain fuel characteristics that will diminish the chance of slagging and fouling, then some swings in variability may be tolerated at some power stations. However, if emissions limits are the issue, then more sophistication may be needed. Emissions limits are becoming stricter with requirements to meet averages for shorter time frames (hours and days instead of weeks and months). These restrictions require closer control over the quality of the blend being fed into the bunkers at the station. Even scrubbed units should have a consistent quality of fuel as feed so that sorbent additions can be minimized. To meet these challenges, engineers must consider available equipment and control techniques and the properties of the parent coals when evaluating new blending systems.

Jan 1, 1994

By C. E. Brechtel

Bench cut-and-fill stopes with heights between 85 and 105 ft are being excavated in the lower levels of the B-NEATH Zone. Estimates of pillar strength and pillar loading indicated a high probability of pillar failure. Some changes in mining practice were made to minimize impacts of pillar failure and a rock mechanics instrumentation program was employed to monitor stability during mining of the first stopes. Limited pillar failure, in the form of destressing, was observed in the initial stopes; however, global stability during mining was good. Instrumentation data indicated that predictions of pillar strength and stress were quite close to field results.

Jan 1, 1989

By J. Davitt McAteer

Improvements in the control of coal mine dust have occurred over the past 25 years. Simultaneously, dramatic improvements in coal mine production technology have occurred, particularly at mines where longwall systems are in use. Production rates of longwall systems have quadrupled since 1978, and dust generation on these systems has significantly increased. However, technology to address control of the resulting increased levels of respirable dust has not kept pace, and many high-production longwall sections continue to experience problems with respirable dust control. This paper seeks to enlist the entire mining community in the effort to resolve the health problems presented by excessive levels of respirable coal mine dust, particularly on longwall systems. These systems are expected to increase in number and length, and to generate increasingly higher levels of dust as production rates of these systems continue to rise.

Jan 1, 1995

By Louis W. Cope

INTRODUCTION Various methods for sampling placer deposits have been mentioned by Wojcik in Chapter 2. Here, a brief description and comparison of these methods will be given as related to bulk versus drill sampling. The advantages and disadvantages inherent to each will also be given. The means of sampling can be grouped into bulk or drill samples. As a generality, drill samples over a five-foot length will run from I/,, to 1 /, cubic yard, depending on the diameter of the drive shoe on the drill casing. Bulk samples can be expected to be in the range from one to many cubic yards each. SAMPLE METHODS Bulk Bulldozer-dug trenches and dozer or front-end loader pits are two methods to excavate large bulk samples. Smaller bulk samples can be obtained by digging small dimension shafts through the deposit, by hand or caisson-like drills. It is not recommended to split samples by alternate bucket-loads or by other means, as the effect of a nugget falling into one or the other fraction will seriously alter the sample.

Jan 1, 1992

By D. A. Smith

The successful integration of overburden casting techniques into the mine production cycle can be an extremely cost effective use of explosives. The entire mining cycle revolves around the cast blasting and to be successful requires a great deal of planning and cooperation. Several operations of Cyprus Coal Company in the Appalachian coal fields have successfully integrated blast casting into their mine plan. This paper will detail the parameters and necessary controls to integrate an overburden casting program into a surface coal operation.

Jan 1, 1993

By A. G. Sciulli, G. P. Ballock, G. Hearnshaw, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water

Jan 1, 1987

By Gary S. Brierley, Ronald E. Romley, Alan L. Howard

The Price Road Drain Tunnel in Tempe, Arizona is part of the drainage system constructed in conjunction with the Outer Loop Highway in metropolitan Phoenix. The Outer Loop Project is a part of a much larger expressway system that includes other large drainage tunnels such as the Papago Freeway Drain Tunnels. Large diameter downhole inspection borings were utilized to obtain subsurface data for the design of these tunnels. Subsurface data obtained from the large diameter borings resulted in the development of empirical parameters that were successfully incorporated into the Geotechnical Design Summary Report and which satisfactorily predicted ground behavior, formed the basis for improved geotechnical design criteria, and facilitated the cost effective assessment of third party risk. The purpose of this paper is to describe the subsurface exploration program performed for this project and to explain the methods used to evaluate underground construction procedures.

Jan 1, 1991

By C. W. Schultz

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained.

Jan 1, 1991

By Carleton K. Smith

Due to special job or client requirements, there will always be some variation in the philosophy of organizing and controlling construction under a project management contract. In typical cases, however, some standard procedures apply. Controls on a construction project are best described only in general terms. They should apply to the total job and can be most effective only when all pieces of the job organization fit together to support a control system for the entire project. Controls are more than a system of reports, schedules, and tabulations-they are the result of an integrated organization dedicated to getting a job done on time and within budget. One of the most important aspects of project control is the construction organization. It must include the right people, facilities, and site equipment, as well as the authority to do what's necessary to accomplish the work. This should be set up to function with as little involvement from off-site or the home office as possible. However, the jobsite construction group must work within established policies and guidelines and is subject to continuous off-site or home office monitoring. In other words, the job-site leaders need to have a clear definition of their responsibility, their authority, and the necessary people and equipment to make things happen. With that philosophy in mind, this is how Bechtel sets up a new job to be

Jan 10, 1980

By Hiroyuki Kawata, Toshiyuki Ueno, Mikio Yamazaki

INTRODUCTION For the construction of several kinds of structures which pass through under railways, we have recently developed an effective and new tunnel construction method, aiming at more secure train operation during the construction as well as the rationalization in the construction works for such structures. Most important in carrying out the construction works for the structures under railways is how to maintain the safe operation of trains. For such construction works, temporary supporting structures and supplemental works have been often applied, for which high cost and long period for the construction have been required. While, this new tunnel construction method has the feature that it is capable of constructing definitive structures for various purposes, which, at the same time, acts as the temporary supporting members for protection of railways. Therefore, this method is now drawing much attention in that higher safety of train operation, low construction cost, and shorter construction period are accomplished, minimizing the period required for slackening the train speed during the construction works.

Jan 1, 1979

By S. Siddiqua

Diffusion is known to be the main transport mechanism of contaminants in fine-gained soils. To date, it is still common practice to estimate contaminant migration in the Bangkok Clay by means of pure advection models. A series of experiments with various chemical species was performed to determine transport parameters such as the diffusion coefficients and the distribution coefficients. The soil used was saturated undisturbed Soft Bangkok Clay. Column experiments were utilized in a number of laboratory tests involving advective-diffusive migration. Effective diffusion coefficients of different ions were back calculated from the test results. The distribution coefficients were determined from the results of the column tests and batch test. The results indicate that the evaluated parameters are in the range of values obtained from other researchers on similar kinds of soil. Based on this results contaminant migration by diffusion in the Soft Bangkok Clay can now be performed.

Jan 1, 2005

By J. H. Hill

The globalization of mineral markets and intense competition in downstream mineral-consuming industries such as transportation, agriculture, and construction are requiring raw materials suppliers to innovate, improve quality, invest in new technology, and control costs. Mineral specifications are becoming more refined, and pressure to improve products is felt from increasing numbers of competing producers, substitute materials, customers, and regulators. As a result, engineered mineral products are becoming more like manufactured ones in terms of cost structure, differentiation, and the importance of market driven, customer specific product development. Engineered mineral products are defined as those where the costs of refining and upgrading outweigh those of conventional mining activities (blasting, crushing, classification, haulage etc.), and where close control of physical and chemical parameters is required for customers' processing and manufacturing applications. This includes industrial minerals such as calcium carbonate, kaolin, mica, specialty oxides, talc, and some metal powders. It excludes most metals and bulk commodity materials such as gypsum, lime, sulfur, and soda ash. Engineered mineral products are utilized in common household goods, and are at the forefront of industrial materials engineering in plastics, ceramics, composites, glazes, coatings, and construction materials. As a group, they introduce interesting questions to the minerals firm. Advanced materials or basic? Diversify or specialize? What are the implications of advanced materials and for mineral markets, and most importantly, where can the producer look for long-term value, volume, and profits?

Jan 1, 1993

Raises are widely constructed underground in hard rock mining for ventilation, material transport or emergency escape. The four major raise excavation methods, Drop Raise, Conventional, Alimak and Raise Bore can be divided into two categories from ground control point of view, one ground support can be installed during excavation, the other not. Excavation method must be chosen carefully to keep the raise wall in stable state during excavation and make sure enough rock stand-up time to install ground support if needed. If rock quality is permitted and there is no strict space limitation, raise bore method which is the only method that ground support can not be installed after the whole excavation is finished should be considered first because it is faster, cheaper, safer and less disturbance to the hosting rock. Support may or may not be needed depends on the purpose of the raise and rock quality. In high quality hosting rocks, if the raise is only for ventilation or material transfer, support may be not needed. If it is for emergency escape or escape and ventilation, which provide or require personnel access, the whole raise must be supported either in high or low quality rock. Based on on site data collection, construction and raise utilization, this paper gave out the rule of thumb how to decide an excavation method. After purpose of the raise, required raise diameter (size) and raise site options being known, geotechnical data collection is the next important step in a raise project.

Jan 1, 2011

By James R. Arnold

Over the past few years several commercial wetting agents and drying aids have been tested in the lab and in the plant at Gold Fields Mining's operations at Mesquite and Ortiz. The major goal was to increase recovery with these surfactants by improving the permeability of the pad and increasing the rate of penetration through the rock.

Jan 1, 1988

By T. M. Biddle

If an accident occurs at a mine, the mining company, its parent and affiliates, and its supervisory employees may face substantial -- and sometimes unexpected -- liabilities and costs. This presentation surveys the likely sources for post-accident exposure, including wrongful death and personal injury claims, mine closure/operational disruptions, and government civil and criminal actions against the company and its employees.

Jan 1, 1986

By Dominic F. Howarth

Cuttability and borability assessment methods in rock and coal are reviewed. TBM, roadheader and coal cutting machine boring rates can be predicted from a knowledge of machine, intact rock property and rock mass parameters. Results that were obtained from a detailed analysis of two TBM borability prediction methods and comparison with data from twenty case histories, show that a simple, low-cost method that uses one machine parameter and one rock parameter compares very favourably with a sophisticated, high-cost method that also includes details of rock mass characteristics (discontinuity, type frequency and orientation).

Jan 1, 1987

By Klaus Schönert, Martin Botsch

In common high intensity magnetic separators, the magnetic particles are deposited on ferromagnetic matrices, such as expanded metals, steel balls or grooved plates, inserted into a strong magnetic field. The nonmagnetic material is flushed through the matrix chamber. Discharging the magnetic particles is only possible if the magnetic field is reduced to zero (e.g. high gradient magnetic filtration for the purifying of kaolin) or the matrix chamber is moved out of the field by a rotor (e.g. the Jones Separator). Therefore, these separators perform only in a batch or semicontinuous mode. A real continuous operation requirs transport of the deposited magnetic material to an outlet where it can leave the separation chamber inside the field. One possibility for accomplishing such separation and transport is through the use of a rotating induction body with a certain shape, such as a spiral.

Jan 1, 1995

By D. Legg

This is the first in a series of studies commissioned by the European Environment Agency that aim to raise awareness of the use of economic instruments and assess their effectiveness. The emphasis is on sharing good practice and increasing knowledge and understanding across European countries in this emerging policy area. A methodology for evaluating the effectiveness of economic instruments has been developed and this will examine whether the inclusion of economic instruments in complex policy packages can improve the overall performance, particularly as a prevention tool in terms of resource use and waste generation The focus for this initial study is the use of aggregate taxes in four EU countries which include the Czech Republic, Italy, Sweden and the UK so that a range of experiences (e.g. geographical, political etc.) can be included. The findings will be used to inform and influence future policy development in other EEA countries. The methodological approach is divided into two main sections: - Technical analysis, which covers quantitative and qualitative analysis. - Process design, i.e. who should be involved when, where and how. Process design is essential if the full learning benefits are to be gained from the technical analysis, which is the ultimate objective of these evaluations.

Jan 1, 2007

By P. Hornby, S. Henley

INTRODUCTION The project described in this paper is designed to provide a standard and flexible method by which data can be exchanged among different systems and packages in common use for geo- logical modelling and mine planning, with substantial savings in ad hoc programming which is expensive and produces interface software that is difficult to maintain. Such packages include specialised applications such as Vulcan, Surpac, Datamine, and Gemcom software, and the Whittle pit optimisation programs, and more general products such as AutoCad, Microstation, and Maplnfo, and database management systems through a generic SQL interface. The data translator is built around the CSIRO Data Model and GeoEditor, and will make widely available the benefits of the Data Model by adding functionality to its implementation in an industry- standard language and style, with interfaces to important geological and mining software products used by the industry, while including also the visualisation and editing capabilities of the GeoEditor which provides the functional framework within which the Data Translator is developed. The Data Translator is intelligent in the sense that it is not a black-box solution but allows visualisation and validation of data during transfer; furthermore it provides a means for changing abstraction levels during the transfer operation. There have been few similar efforts to address this problem. It is not a problem which is likely to be solved in any general or long- term way by any individual commercial software vendor. THE CSIRO DATA MODEL A wide variety of software tools have entered the exploration and mining industries via different pathways. Examination of these pathways and the origins of the software illuminates the types of data transfer problems and difficulties which might occur in the day to day life of exploration and mining operations. In exploration, the focus is normally on a large area (>5000km2) which is explored primarily in two dimensions. For 20 exploration purposes, geographical information systems (GIs) software, image processing software, and, in some cases, 20 computer aided design (CAD) software have been employed. Typically, GIs soft- ware is used the most by lands and tenements personnel and government geological survey organisations, image processing software is used the most by geophysicists, and 20 CAD software is used the most by drafting and geology personnel. In contrast, within the mining environment, almost all activities have 3D character. In this realm, 3D CAD software and specialised mine planning and design software are important. Specialised mine planning and design software is similar to 30 CAD software, but typically has additional capabilities such as specialised modules for surveying, drill hole data operations, open pit design and optimisation, underground mine design, mining block model creation, and/or ore reserve calculations. Unfortunately, the different origins of the software in exploration and mining lead directly to problems in data exchange and the design of seamless software systems. These problems result from the different data management strategies employed by the different classes of software. In order to address these problems, CSIRO Exploration and Mining and CSIRO Division of Information Technology have been investigating the structure, character, and syntax of data and soft- ware present in computer-aided exploration and mining activities since early 1993. The goal of this effort is to 1) systematically ex- amine the breadth and depth of the data in use within exploration and mining, and to 2) promote a data organisation strategy which is broad enough and comprehensive enough to enable wiser soft- ware design and easier data transfer. In the short term a data model can be used to improve data transfer; in the longer term it is hoped that a data model framework will help object-oriented concepts to enter the next generation of geoscientific software. The data model is described in more detail by Power et al., 1995. THE DATA TRANSLATOR PROJECT The CSIRO Data Model provides a basis for a very wide range of applications in geology and mining. It has been developed over the past two years by a joint team from the Division of Exploration and Mining and the Division of Information Technology, and its principal purpose is to provide a comprehensive and self consistent model of the geometric and topological properties of geological and mining data. The project is being carried out by CSIRO with the support of Australian mining companies through AMIRA (the Australian Mining Industries Research Association). Eight companies are sup- porting the project : • North Ltd Minenco • MIM Exploration • Fractal Graphics • BHP Australia Coal • Pacific Coal • Gencor CRA Exploration The systems to be interfaced have been decided by comparing the priorities of the various sponsors, to produce a final combined priority list as follows : • Vulcan • Minescape • Micromine • Mapinfo INTRODUCTION The project described in this paper is designed to provide a standard and flexible method by which data can be exchanged among different systems and packages in common use for geo- logical modelling and mine planning, with substantial savings in ad hoc programming which is expensive and produces interface software that is difficult to maintain. Such packages include specialised applications such as Vulcan, Surpac, Datamine, and Gemcom software, and the Whittle pit optimisation programs, and more general products such as AutoCad, Microstation, and Maplnfo, and database management systems through a generic SQL interface. The data translator is built around the CSIRO Data Model and GeoEditor, and will make widely available the benefits of the Data Model by adding functionality to its implementation in an industry- standard language and style, with interfaces to important geological and mining software products used by the industry, while including also the visualisation and editing capabilities of the GeoEditor which provides the functional framework within which the Data Translator is developed. The Data Translator is intelligent in the sense that it is not a black-box solution but allows visualisation and validation of data during transfer; furthermore it provides a means for changing abstraction levels during the transfer operation. There have been few similar efforts to address this problem. It is not a problem which is likely to be solved in any general or long- term way by any individual commercial software vendor. THE CSIRO DATA MODEL A wide variety of software tools have entered the exploration and mining industries via different pathways. Examination of these pathways and the origins of the software illuminates the types of data transfer problems and difficulties which might occur in the day to day life of exploration and mining operations. In exploration, the focus is normally on a large area (>5000km2) which is explored primarily in two dimensions. For 20 exploration purposes, geographical information systems (GIs) software, image processing software, and, in some cases, 20 computer aided design (CAD) software have been employed. Typically, GIs soft- ware is used the most by lands and tenements personnel and government geological survey organisations, image processing software is used the most by geophysicists, and 20 CAD software is used the most by drafting and geology personnel. In contrast, within the mining environment, almost all activities have 3D character. In this realm, 3D CAD software and specialised mine planning and design software are important. Specialised mine planning and design software is similar to 30 CAD software, but typically has additional capabilities such as specialised modules for surveying, drill hole data operations, open pit design and optimisation, underground mine design, mining block model creation, and/or ore reserve calculations. Unfortunately, the different origins of the software in exploration and mining lead directly to problems in data exchange and the design of seamless software systems. These problems result from the different data management strategies employed by the different classes of software. In order to address these problems, CSIRO Exploration and Mining and CSIRO Division of Information Technology have been investigating the structure, character, and syntax of data and soft- ware present in computer-aided exploration and mining activities since early 1993. The goal of this effort is to 1) systematically ex- amine the breadth and depth of the data in use within exploration and mining, and to 2) promote a data organisation strategy which is broad enough and comprehensive enough to enable wiser soft- ware design and easier data transfer. In the short term a data model can be used to improve data transfer; in the longer term it is hoped that a data model framework will help object-oriented concepts to enter the next generation of geoscientific software. The data model is described in more detail by Power et al., 1995. THE DATA TRANSLATOR PROJECT The CSIRO Data Model provides a basis for a very wide range of applications in geology and mining. It has been developed over the past two years by a joint team from the Division of Exploration and Mining and the Division of Information Technology, and its principal purpose is to provide a comprehensive and self consistent model of the geometric and topological properties of geological and mining data. The project is being carried out by CSIRO with the support of Australian mining companies through AMIRA (the Australian Mining Industries Research Association). Eight companies are sup- porting the project : • North Ltd Minenco • MIM Exploration • Fractal Graphics • BHP Australia Coal • Pacific Coal • Gencor CRA Exploration The systems to be interfaced have been decided by comparing the priorities of the various sponsors, to produce a final combined priority list as follows : • Vulcan • Minescape • Micromine • Mapinfo • Medsystem

Jan 1, 1996