Search Documents

By K. E. Brown, T. D. Murphy

At Monterey Coal's No. 1 Mine in central Illinois, it became necessary to predict if the sulfur content of individual trainloads of coal would exceed a contract sulfur maximum. Using geostatistics and Monte Carlo-type simulations, a forecasting procedure was developed to meet this need. The developed procedure predicts the monthly, mean sulfur content of the coal shipped and the probability of individual shipments exceeding the contract limit. During the first five months of using this procedure, the forecasted, monthly mean sulfur value was within 0.03% of actual. This represents a significant improvement over the inverse-distance, gridding-based, forecasting used previously.

Jan 1, 1994

By Tracy E. Barnes

The process of computerized reserve estimation consists of assuming a model of the spatial continuity of a deposit and then, working within the assumed model, estimating the grade and tonnage of the deposit. The basis for geostatistical analysis is a statistical definition of this continuity or the variogram. The true variogram is essentially impossible to define. So an experimental variogram is defined from the sample data and kriging proceeds assuming that this experimental variogram is a good approximation of the true variogram. Therefore the closer the experimental variogram is to the true variogram the better the estimate will be. Realizing that the variogram is nothing more than the definition of the spatial continuity of the deposit, taking the known geologic continuity of the deposit into account will give a superior variogram. The use of known geology is a widely recognized necessity for good structural analysis of a deposit, but is rarely fully incorporated into the structural analysis.

Jan 1, 1982

By Murali M. Gadde, Syd S. Peng, C. T. Holland

Cutter roof failure is one of the most common ground control problems affecting the safety and economy of an underground coal mine operation. Several attempts were made in the past to understand the processes responsible for cutter development and to devise mitigating measures. Yet, many cutter failures still happen and their advance prediction remains as elusive as before. One of the reasons for the impasse in predicting cutters lies in the limitations of the current numerical modeling technologies. The development and propagation of cutters is a progressive phenomenon and continuum models can only approximate this process. Since the discontinuum modeling is severely restricted by the lack of reliable input data, alternatives must be sought to better understand cutter failures using the continuum models. This paper proposes one approach using strain-softening material model to simulate the cutter initiation and propagation process. An attempt has also been made to provide some insights into the reasons for the change in cutter location at different parts of a development layout.

Jan 1, 2005

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH's Pittsburgh Re¬search Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, which are tightly wrapped with many turns and which carry current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften, making them prone to damage. The damaged insulation reduces the life of the cable and can lead to shock, electrocution and mine fires. This paper describes a method of measuring the conductor tem¬perature of mine trailing cables during normal operation. The temperature is measured using a 50/125-, µm graded index multimode optical fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an optical time domain reflectometer (OTDR). This system is capable of measuring temperatures with an accuracy of ± I °C over a length of 4 km at I -mintervals. With this unique way of measuring temperature, tests can be conducted that simulate actual mine conditions. The tests provide important data that allows MSHA's Approval and Certification Center to develop approval criteria for cycli-

Jan 1, 2000

By SAMUEL A. LOLON, ADITYA JUGANDA, JURGEN F. BRUNE, JR. GREGORY E. BOGIN

Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of explosive methane-air mixtures, herein referred to as explosive gas zones (EGZs) [1]. The risk of mine explosions can increase if these EGZs migrate out from the gob into the surrounding mine entries — a phenomenon known as gob breathing. A number of 3D computational fluid dynamics (CFD) simulations using various magnitudes and periods of barometric pressure variation have indicated that the EGZ outgassing potentially occurs due to lags in pressure, which are strongly influenced by mine conditions and ventilation systems. Early-warning systems with real-time pressure monitoring and the application of gob ventilation boreholes are recommended to detect and mitigate explosion hazards from gob outgassing.

By Song Xiaotian

Studies have been carried out to optimize the VCR's mining sys- tem on the basis of synthetic analysis at Fankou Pb-Zn mine in Southern China. The synthetic e- valuation method is proposed for selection of mining alternatives and stope dimension optimization techniques. Theoretic calculation and computer optimization of the fragmentation of rock blasted by multispherical explosive charges are discussed. The mathematical and optimal fragmentation models are built. The optimum model is built for the main mining operations such as drilling, blasting and haulage. Lt can be used to evaluate VCR?s mining projects, select mining parameters and provide design fundations. From the point of view of system research on the geomechanical process, stoping technological process and benefit, the complex method of optimization is proposed for VCR's mining. Using computer simulation, based on this model, the optimal parameters are established and analysed. An effective approach is provided for research on the mining method optimization and getting better economical benefits from the application and improvement of VCR's method.

Jan 1, 1986

By Y. C. Kim

For the past quarter of century, much more effort and research have been expended in developing the "optimum" ultimate pit limit design algorithms and much less to solving the "optimum" open pit production sequencing. However, the potential economic benefit to an operating mine is far greater for the latter than the former. Unfortunately, the problem of "optimum" open-pit production sequencing has not been fully solved to date. This paper first reviews the past and currently used methodologies for developing this sequence. The staggered pit phase geometry problem of advanced stripping and operational constraints such as ore and waste tonnage requirements by period and necessary contiguity of mining faces are the main reasons why the "optimum" production sequencing problem has not been solved as yet. This paper also explains why any method which attempts to simplify the problem using ultimate pit limit design algorithm will fail to reach an "optimum" solution.

Jan 1, 1994

By P. M. Brown

The Bureau of Mines, U. S. Department of the Interior, has developed a method of dewatering clay slurries based on flocculation by high-molecular-weight polymers and water removal from the formed flocs using a trommel or hydrosieve. The exchange ion on the clays affects their dewaterability. Metal ions in solution and on the exchange sites of smectite clays are known to act as Lewis acids. Recent work has determined that these ions can be titrated with high-molecular-weight polymers. The relative acidity of the exchange ion and the basicity of the polymer determined by the new method give insight into the dewatering mechanism.

Jan 1, 1988

By Richard A. Williams

The design, modelling and simulation of solid-liquid mixers remains one of the least advanced aspects of minerals processing, due to difficulties in quantifying complex slurry hydrodynamics from first principles, and in acquiring reliable experimental data for model verification and development. This contribution describes the application of electrical resistance tomography (ERT) for three dimensional imaging of the concentration of mineral particulates in a slurry mixer as a function of key process variables (particle size, impeller type, agitation speed). It is demonstrated how ERT can provide a wealth of detailed data to allow model development, which ultimately will lead to much improved design capabilities and the generation of mixing models which could reside within Particle Process Simulators. This principle is illustrated using descriptions of mixer behaviour based on an empirical approach, although the measurement methodology described is equally suited to development of computational fluid dynamics models, cellular models or design approaches based on artificial intelligence. The experimental data can be built into a visualisation data bank, which acts as a "process toolkit" by allowing a library of process responses to be catalogued. Hence these data can be accessed for the purposes of model development, equipment selection, optimisation of operating conditions or testing on-line control strategies.

Jan 1, 1995

By Marco Aurelio Piangatelli, Massimiliano Bringiotti, Ferdinando De Angelis

"The construction of the three connecting tunnels between the east side and the west side of station C13, adjacent to the Vistula river, has a long and complex history, as they cross beneath one of Warsaw’s main road arteries (Wislostrada). After the attempt to excavate the first tunnel, the face of the tunnel collapsed on the night of August 13, 2012, and a volume of about 10,000 cubic meters of liquid mass (water, silty soil and sand) entered and flooded the west side of the station, which was filled with more than seven meters of material. Fortunately, the workers managed to escape, but machines and equipment were lost. This is the story of how the tunnels were completed, by adopting soil improvement, jet grouting, GRP bars, ground freezing and a careful choice of work steps. INTRODUCTION The Centrum Nauki Kopernik station on Line II of the Warsaw Underground is located alongside to the Vistula river (Figure 1). This station hereinafter is referred to as station C13.The station consist of three parts: the east and west part, and three connecting tunnels 40 meters in length with a large cross section (170 m2).. It includes the rails along the sides and the platform along the centre. The reason for the underground connection of two shafts with a tunnel is due to the presence of a road tunnel (Wislostrada, hereinafter called WS), which must be underpassed by the new metro line (Figure 2).The existing tunnel (Wislostrada) was built many years before, between diaphragm walls, and some foundation structures interfere with the underground tunnel. The challenge was to build the connectors without stopping the traffic of vehicles along the highway above. All works took place in very difficult geological and groundwater conditions due to the presence of Vistula alluvial deposits with poor mechanical characteristics. The soil profile consists of relatively loose sands on top, and silts overlying high plasticity Pliocene clays highly disturbed by the effects of the repeated over-sliding of glacial moraine deposits."

Jan 1, 2016

By Thomas J. Martin, James W. Martin, Paul F. Martin

The conveyor belt is the basic building block of a broad range of material handling applications in modern mining systems. The mining plans and site conditions dictate basic system requirements but this is only a part of total design evaluation. The total system in the typical mining situation can encompass all the activities from the excavators at the mining face to the processing plant, site loadout facilities and/or a power plant. The number of alternative configurations which must be evaluated including subsystems and components is limited only by analytical time and creativity. The constraints and issues which must be addressed continue to expand, driven by reliability, environmental impact and cost competitiveness. All of the system requirements must be translated into specifications for costing, final design and construction.

Jan 1, 1993

By Roland Froidevaux

The potential use of geostatistics for quantitative ore reserve reporting is shown using a simple gold case study as an example. The need of defining quantitative class limits is stressed, and a possible approach to this problem is suggested.

Jan 1, 1983

By Xiangze Shu, Yuzhong Xing

All programs used to optimize main fan nowdays have to be run on the large and medium- sized computers. With a lot of array elements, complex processes, low convergence speed and large storage, these programs are both time consuming and difficult to be used in the micro computer. This program uses two languages (dBASEIII and BASICA) to calculate the network and to choose the fan respectively. It allows user to compare and choose the parameters of various kinds of fan and to transfer the selected fan parameters to the master program by a data communication system. Then the user can get the air quantity, the air pressure, the power and the efficiency of the main fan. The advantages of this program arc as follows: 1. It can be run on IBM-PC or compatible micro computer. 2. It can select a fan more quickly and less time consumingly. 3. It can choose desired one or a set of fans according to user's requirements. 4. It is suitable for the research institutions and coal mines.

Jan 1, 1991

By M. García-Vásquez

In Peru, the third destination in worldwide exploration based on expenditure, mining conflicts have spread dramatically over the last decade. Mining companies need to create new initiatives to avoid social conflicts and strengthen the social capital needed to keep mining in a country with proven mineralogical riches. This document provides information about a research project that explored the opinions and experiences of a resource many times overlooked by companies: the human resource. Over 30 surveys were conducted among professionals working at mines in the Peruvian mining industry, in different departments and from different organizational levels. Mining employees acknowledged that they play an important role in the development of company-community relationships and gave their impressions about initiatives implemented by international mining companies in Peru. Mining employees also provided their recommendations to succeed in a location where cultural differences have not been properly considered.

Jan 1, 2011

By F. Breu, R. Fraser, R. Lawrie

Diesel-powered underground mining equipment is generally accepted as the most productive, safest, and most efficient equipment used in underground mining operations. Widespread application of this equipment to underground mining is restricted, however, largely because of the difficulty of controlling the diesel engine exhaust emissions. This paper briefly examines control devices currently available for underground application, and also discusses the theory and mechanics of controlling diesel emissions with particulate traps and filters.

Jan 1, 1988

By J. J. Peshel

As per the current conceptual design presented by the Department of Energy, the exploratory shaft facility (ESF) becomes a part of the repository if the Yucca Mountain site is found suitable for repository development. Therefore, the design of the ESF should be compatible with the performance requirements for the repository. The construction methods selected should limit to the extent practical, the degree and the extent of damage to the surrounding rock mass. The ESF construction and operation should be compatible with the site data gathering activities, such as geological, thermomechanical, hydrological and geochemical testing.

Jan 1, 1991

By J. P. Savely

This paper describes the development of a trim blast design to improve the stability of a final pit wall. Description is given of the effects of rock characteristics, rock type, and pit plans on the blast design. Currently, six benches have been mined with trim blasting. A more stable final wall has resulted and the successful program has reduced mining costs over an extended time period. Low-cost blast monitoring and field observation were used to determine peak particle velocity and blast damage. Using criteria developed from this relationship, trim blasts were designed and evaluated.

Jan 1, 1987

By David R. Shaddrick

Ore reserves are based on sampling developed by drilling programs. Correct choices concerning the type of drill to be used, depth of drilling, hole orientation and sample spacing are not only critical to the accuracy of the ore reserve but to the cost in time and money of the project. Appropriate interpretation and use of geologic information can significantly enhance the ability to make these decisions effectively. Geologic characteristics of mineralized rock that affect drilling and sample quality include: rock quality, openness, water content, mode of gold occurrence, internal gold distribution and grain of mineralization. Each of these characteristics and sources of data about them are revuewed, then related to the various drill program options. Finally, some procedures for checking the validity and appropriateness of the selected options are reviewed.

Jan 1, 1987

By Merrill P. Allen

The Vernal phosphate rock concentrator is located in the Uinta Mountains near Vernal, Utah. Ore is sedimentary rock from the Phosphoria Formation. Truck and shovel mining is done at a rate of 11,500 TPD. Run of mine ore is crushed and then milled through a SAG mill and ball mill to minus 16 mesh. Milled ore is deslimed using cyclones and hydrosizers. Sands are conditioned with fatty acid, petroleum sulfonate, diesel fuel and frother prior to primary rougher and cleaner flotation. Primary flotation tailing is milled to 95% minus 48 mesh, deslimed in cyclones, conditioned using reagents previously described, and then processed through rougher and cleaner scavenger flotation. Product of scavenger cleaner concentrate is upgraded by reverse flotation of dolomite. Flotation concentrates are combined and dewatered, pulp being milled to 99.5% minus 65 mesh and then thickened to 65% solids. Product is pumped from storage through a 10 inch, 94 mile pipeline to a conversion plant at Rock Springs, Wyoming. Mill tailing is stored behind an earthen dam, water from the settled tailing being reclaimed for mill use.

Jan 1, 1993

By S. Page, R. Bhaskar

The development is described of a real-time tracer gas sensing system for use in fell-scale laboratory studies of air flow behavior around mining machines. A semiconductor sintered tin-dioxide gas sensor is used for gas analyses. A data acquisition and analyses software specific to the sensor characteristics was also developed as part of the system. The system permits the study of transient behavior and assists in obtaining a better understanding of the movement of air around mining machines and in the study of the effect of potential airflow modification devices on the dust exposure of face personnel. It seeks to replace the current method of using a centralized infrared gas analyzer that polls several sampling points using an array of solenoid valves and gas line purgers. The polling results in a significant time lapse between the first and the last set of readings. The system described in this paper has the advantages of real-time sampling and safe operation.

Jan 1, 1992