Search Documents

By H. Nematollahi

Numerous magnesite deposits are found in the south part of Khorasan state, east of Iran. During the past few years, production of high-grade magnesite ore was possible only by using selective mining method. The decreases of high-grade ore imply upgrading of the low-grade ore. To do so, the objective for the first phase is to obtain a material which contains less than 2.5% SiO2. The present study was carried out based on three different samples. The results obtained in laboratory indicate that the direct flotation of magnesite by fatty acids led to acceptable result.

Jan 1, 2003

By Rolando V. Cuaño

For geostatistical applications, heterogeneous spatial phenomena are better modeled as mixtures of populations. However, the modeling of the constituent populations can become complex. The alternative mixture model offers a simplified approach to the w modeling problem. The model is applied and tested on the Walker Lake data set. Compared to the univariate ordinary kriging model, the alternative model generates less biased block estimates.

Jan 1, 1996

By Eric Hansen, Todd Wanless, Chris Mueller, Shannon Dunne, Scott Elmer

Between 2010 and 2018, Houston added more than 1 Million residents; the third largest rate of growth in the nation. With growth, the region faces new challenges with water supply, capacity of its wastewater system, and regional drainage. While tunnel construction has been limited in Houston since the Clean Water Program of 1990s, it is about to see a resurgence to improve water supply reliability and to reduce flood risks and sanitary sewer overflows. This paper examines the challenges with “going deep” below the built urban environment and related to high ground water; stiff, fissured clays; flowing silts and sands; faults; hazardous materials; and abandoned well fields.

Jun 13, 2021

By C. DeRossett, K. F. Unrug

Sedimentary rock fractures commonly occur in the vicinity of outcrops. Mine highwalls and highway cuts provide excellent views of these near-surface joint systems. This paper explains the origin, characterization, distribution and extent of the these joint systems with reference to the lithologic composition of the rocks. The practical implications of these joint systems on the operation of a mine are described. Included are discussions of the discontinuous deformation that results from surface subsidence, the stability of mine portals and near-outcrop underground operations, and the stability of highwalls when using highwall miners and strip operations. Some design procedures are recommended to minimize the problems encountered within mining areas having intense joint systems.

Jan 1, 1996

By R. W. Waytulonis

New exhaust control techniques and devices may be necessary to meet future diesel particulate matter emission standards in underground coal mines. This paper reviews conventional work practices and devices used to control diesel exhaust emissions, and new techniques being tested by the Bureau of Mines. Discussions will center on important work practices and on the function and efficiency of exhaust after-treatment devices. An industry/government cooperative research project to develop and test an exhaust after-treatment system for part 36 equipment is also discussed.

Jan 1, 1990

By Javad Sattarvand, Amin Moniri-Morad

Predicting equipment failure behavior plays a critical role in providing a safe operation. Although various reliability evaluation methods are available for estimating failure behavior profiles, these approaches are based on mathematical formulation, leading to actual operation simplification and improper estimation of failure trends. This study proposes a discrete-event simulation (DES) approach to model fleet failure behavior. This approach can model the maintenance strategies in multi-component systems with minimum simplifications. In this regard, the first step was to collect a historical failure time dataset (e.g., the time between failures). Then, the DES model is established to predict the severity of failure events and design maintenance strategy considering actual operation circumstances. Afterward, the maintainability analysis was performed to estimate equipment downtime and availability. The achieved results showed that the system availability was about 85%. Also, the findings demonstrated that the DES could efficiently predict the equipment failure behavior using various stochastic events.

Jun 25, 2023

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are some of the most widely used instruments in a variety of industrial applications. Their major functions are to sort, classify and separate solid particles and liquid droplets within a multiphase flow system. Research studies employing both experimental and numerical methods recognize that the performance of a cyclone is related to its geometric dimensions as well as the inner flow pattern. Although many successes have been achieved over the past years, the majority of investigations only focused on the simplified design of cyclone geometry and on single-phase flow. Therefore, this study set out to investigate the flow field in a new-design hydrocyclone and used particle image velocimetry (PIV) to explore the complex swirling flow behavior inside the cyclone within an air core. The flow field inside the cyclone was also studied by computational fluid dynamics (CFD) simulation using a commercial CFD package. Different turbulent models were tested in this study with a moderate-size mesh, and the interface of liquid phase and air phase was predicted by the volume of fluid (VOF) model.

By Earl H. Miller

The United States Potash Company was the original discoverer and first producer of under-ground mined potash ore in North America and commenced active production of potash in 1931. In July 1956, the company merged with United States Borax & Chemical Corporation and is now a Division of that corporation. The mine is located twenty-two miles east of the city of Carlsbad and the refinery is located sixteen miles south of the mine, The mine was placed where the ore was found and the refinery placed where there was sufficient water for a dissolving and re-crystallization plant. For twenty-three of the last twenty-six years, the potash ore was mined with the room and pillar method, taking approximately sixty percent extraction and leaving forty percent in pillars. These pillars are generally fifty-eight feet by fifty-eight feet square. Three years ago, it was decided that removal of as large an extraction as possible from these pillars should be commenced.

Jan 1, 1958

By Aidan Giblett

"It is important to make a clear distinction on the scope of work of the Global Mining Standards and Guidelines (GMSG) guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and consequently require a large amount of information to calibrate and validate the unit models. As a result, these surveys are labour intensive, somewhat expensive, depending on internal capabilities of the mine site or company and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions.As a result of these factors, full grinding circuit surveys are not a common occurrence at a large number of processing facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices.To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result, it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. These methods can also be manipulated by an experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, allowing an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2015

By Paul F. Ph. D. Ziemkiewicz, Courtney D. Black

According to the American Coal Ash Association, 105 million tons of coal combustion products (CCP) were produced by the power generating utilities in 1997. Of that total, 1.68 million tons were used in mining applications (ACAA, 1997). Results have ranged from the environmentally beneficial to neutral and, in some cases, detrimental. Twenty years ago coal ashes: bottom and fly ashes constituted nearly all CCPs. With the shift to new emission control technologies at power plants, however, large volumes of new products are being generated. Many do not lend themselves to traditional ash applications such as cement formulation. Many CCP disposal sites are not documented with reliable pre and post application monitoring. In this report we discuss types of CCP, their relevant characteristics and the mining environment. We have attempted to identify a range of documented applications and to draw conclusions about their environmental effects including benefits and adverse impacts.

Jan 1, 2000

By C. Cardoso, G. Bermudez, A. Jalili

Bigger flotation cells can result in larger froth surface areas and longer froth transport distances, this has been credited to impact froth recovery. Thanks to recent advancements, the newer flotation machines can be designed with different launder and crowder arrangements to enhance froth management. Nevertheless, lower head grades, complex ores and even larger mechanical flotation cells can lead to insufficient froth collection, even if the cell is equipped with the most recent flotation advancements like the center launder design. Aforementioned issue can become critical at the end of the flotation row. Increased crowding has been proven to be a solution to overcome inadequate froth recovery. However, scaling-up crowders for larger flotation cells can rise challenges, particularly in terms of structural limits and design for service. This paper presents the development journey for the Spider Crowder Upgrade, an advancement to improve froth collection in large flotation cells that are already equipped with center launders.

Feb 1, 2024

By T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate: 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3) Azospirillum had no effect on canopy cover.

Jan 1, 1999

By J. P. Savely, D. E. Nicholas, R. D. Call

Slope stability is a probabilistic phenomenon and as such should be analyzed with probabilistic methods. Fracture orientations alone, insufficiently model the rock mass. Other parameters describing the fracture set characteristics are required with distributions that can be sampled to fit mathematical stability models. Important considerations are length, spacing, dip, waviness angle, and overlap. These parameters are of major concern in design and are difficult to measure. Reasonable estimates of the characteristics can be used to provide distributions.

Jan 1, 1977

By P. Bevilacqua, G. Vallebuona

Empirical models are now used for predicting the performance of hydrocyclones in terms of capacity. cut size (d50.c), water split and partition curve. These models (such as the model by Lynch and Rao and the model he Plitt) were developed and checked for hydrocylones with diameters larger than 4 in. However, for smaller-diameter hydrocyclones, little empirical modeling has been done. This paper reports on an extended experimental research program on small hydrocyclones. For these cyclones, the suitability of existing empirical models was investigated and their accuracy was compared. To improve the predictive capability of these models to small cyclones modifications to the equations are proposed.

Jan 1, 1996

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By T. W. Healy, M. S. Moignard

The use of electrokinetic or zeta-potential phenomena in studies of the properties of mineral sulphides has increased greatly over recent years. This review aims to examine and discuss the body of literature on the subject of electrokinetic properties of sulphides in a comprehensive and critical manner. Although the review covers the period from 1925 to 1975, it is only in the past ten years that researchers have been fully aware of the implications and problems of chemical reactions, notably oxidation and precipitation reactions, on the surface properties of sulphide minerals. These papers are discussed in more detail than the earlier publications. A table containing a list of determinations of iso-electric- points and points-of-zero-charge of mineral sulphides, and the methods employed in obtaining these results, is presented.

Jan 1, 1976

By Randal J. Barnes

The January 1988 issue of Engineering and Mining Journal includes two short articles on blasting practices in surface gold mines (Anon., 1988 ; Carr , 1988). A reader of these articles learns, among other things, that a "12 x 13 ft" blasting pattern is used at the Carson Hill Mine, and a "17-ft burden and 18-ft spacing" is used at Echo Bay Mineral's Borealis operation, while at Mascot's Nickel Plate Gold Mine "ore shots are on a 10 x 10 ft" pattern. Like a new edition of the World Book Almanac, these articles are overflowing with useful tidbits of technical data; but, they never mention why the particular blasting patterns were selected. A survey carried out during the Winter of 1988 at six surface gold mines in the western United States also failed to produce a satisfactory answer. The responses from mine planning engineers to the question "why is your blasting pattern X by Y", reduced to "we use X by Y here because we used X by Y at our last operation, and it worked ok." Certainly, with the available decades of experience and professional practice in blast holes design, rock fragmentation in surface mines has been thoroughly investigated. However, and this is the central issue, fragmentation of the rock is not the primary purpose of most rotary drill holes in surface gold mines. Quoting senior mine engineers from companies operating, three of the richest surface gold mines in the world (AMAX Gold, Homestake Mining, and Gold Fields Mining)

Jan 1, 1989

By Robert P. Mahoney, William J. Roe

Polymers of a wide variety of composition are used in coal and mineral beneficiation. Applications include flocculation and coagulation in thickeners, filtration enhancement, mill scale control, dust control, ore leaching improvement, and pond management. The proper chemistry of the polymer is determined by many factors, including the nature of the process, mineral type, and respective performance requirements. This paper provides an overview of the various current applications of polymers in mineral processing, and a description of the applicable polymer chemistries which find utility in these applications. Examples of structure/performance relationships are discussed.

Jan 1, 1994

By Roger P. Ashley

The main problem in geochemical exploration for gold ore bodies in the 40 km2 hydrothermally altered area at Goldfield is to decide which of the many silicified ledges exposed are most likely to yield deposits with additional subsurface exploration. We conclude that the most efficient way to search for exploration targets is to collect rock samples from the ledges and analyze for the following elements in decreasing order of priority: gold, lead and silver, bismuth, and mercury. These elements form relict hypogene aureoles restricted to the ledges and are not appreciably redistributed during supergene leaching.

Jan 1, 1978