Search Documents

By M. J. Shulman

The exploration geologist is frequently confronted with the problem of allocating his resources, i.e., exploration effort, among various areas. Although geologic, financial, and logistic considerations influence the allocations, no objective criterion is usually given that determines the optimal allocation. Maximizing the expected gain in information, subject to the constraint of a limited exploration budget, is used as the objective criterion to allocate airborne reconnaissance effort. The information function, I(x), quantifies the expected gain in information, where x is the scale of exploration. To calculate the information function, the following probabilities are required: the probability that an area contains a deposit; the probability that an anomaly is produced by the target; and the probability that an anomaly is produced by a barren area (false signal). Alternatively, the barren areas can be replaced by other targets. To illustrate the allocation method, the optimal number of line kilometers, i.e., the optimal line spacing per area, is determined for an aeromagnetic survey for iron in Egypt.

Jan 1, 1987

By D. A. Rice, R. G. Swanton, A. May, O. C. Carter

As part of a cooperative effort between the US Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input from the phosphate industry, the conversion of phosphogypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: (1) thermal treatment to volatilize sulfur. and (2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1987

By L. Tondo, W. Lim

The high pressure grinding rolls (HPGR) is a relatively new technology which offers the potential benefits in energy savings, circuit simplicity and improved product characteristics in minerals processing applications. Over 300 machines are now operating world-wide, but most of these are used for grinding cement clinker, and relatively few are used in conventional mineral processing. One of the rea- sons for its current limited use in the minerals processing industry is that design, scale-up and flowsheet assessment procedures are seen to be relatively immature and untested. This has reduced confidence in the potential application of the technology. To help rectify this situation an industry funded research project was undertaken, one of whose aims was to develop and prove a mathematical model of the HPGR and a scale-up procedure. Data were collected from tests using laboratory, pilot and in one case a full scale unit (2.2m diameter). A range of feed types were tested including quartz, limestone, kimberlite, bauxite, iron ore and gold ore. These data were then used to develop models of the size reduction performance, power draw, throughput and operating gap for a wide range of pressures, feed sizes, and roll speeds. This paper describes the models that have been initially developed and illustrates their accuracy using some of these data.

Jan 1, 1998

By I. J. Jansen, C. L. Hooks

Successful soil construction involves prepa¬ration of an adequate base, selection of high quality soil ma¬terials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experi¬ments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construc¬tion. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By Subhash B. Bhagwat

No economic activity would take place without human ingenuity, driven by our needs and wants. Economic activity is made possible by the energy from fossil and other energy sources, our technological hardware, the buildings and infrastructure made from materials such as metals, plastics, wood, water, and numerous industrial minerals. Industrial minerals are difficult to define; however, they generally include utilitarian minerals other than metals and fuels. Some of the industrial minerals form an exception to this categorization and, as explained elsewhere in this book, belong to more than one category because of the manner in which they are used. Industrial minerals are so numerous, and their applications so ubiquitous that they often do not receive the attention given to metals or fuels. Nevertheless, without industrial minerals, many of our most fundamental economic activities such as construction of our cities and towns, control of floods, transportation of our people, the search for minerals, the smelting of metals, and the delivery of supplies of clean water would be impossible. How then do we assess the economic importance of such a variety of materials lumped together under the general designation of industrial minerals? The price per ton or the total amount consumed do not satisfactorily explain the relative value of these materials to the economy. For example, the current price of limestone is about $5/t and the price of fluorspar is about $190/t. However, nearly 1.1 Gt of limestone, valued at about $5.5 billion, are consumed in the United States annually, compared with 590 kt of fluorspar, valued at about $1 12 million. It would not, however, be accurate to conclude that the mineral with the higher total value is always more economically important. Many other questions must be answered before making judgments of this type. These questions include how many people are employed in the production, processing, and distribution of the mineral? How is the mineral used? Is it partly or entirely imported? Where do the imports come from? How is the mineral transported? Is the mineral considered critical to national security? Is there a substitute material available in case the mineral supply is interrupted? Where would the substitute be produced? What would be the basic material from which the substitute will be produced? Even when these questions have been answered satisfactorily, the economic importance of the mineral is not completely known until the consuming sectors are studied as well. For example, even though the manufacture of fighter aircraft is vital to the national security, it employs only a fraction of the number of people employed in the housing and construction industry or the automobile industry or the appliance industry. Mineral commodities consumed in these latter sectors of the economy are more significant than those consumed in the production of fighter aircraft, because nearly two-thirds of the Gross Domestic Product (GDP) depends on the purchasing power of individual consumers. In comparison, the entire defense budget accounts for only 6% of the GDP. There is no easy way to present the importance of industrial minerals to the US economy because most minerals have diverse applications and products made from industrial minerals often con- tribute to the production of other goods and services. One way of highlighting the value of a mineral would be to relate it to the GDP reported by categories such as construction, machinery, stone, clay and glass products, electrical and electronic equipment, paper and allied products, and chemicals and allied products. These GDP categories represent industries fundamental to the economy totaling $644 billion, or about 12% of the GDP in 1990. However, these categories are not convenient for discussion of the many minerals that are used in our complex economy. In a general way, minerals are the 5% of our economy that make the other 95% possible. This chapter, therefore, discusses a selected few industrial minerals to illustrate their importance to various sectors of the economy.

Jan 1, 1994

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By Chris Lynagh, Collin Schroeder

Determining the best excavation method is a critical step in successful tunnel construction. In rock tunneling, several factors can dictate the excavation method, such as: (1) rock characteristics, (2) tunnel size and length, (3) nearby utilities/infrastructure, and (4) contractor’s preferred means and methods. This paper discusses the various rock tunnel excavation methods utilized on the Doan Valley Storage Tunnel Project (DVT), a project constructed as part of the broader Project Clean Lake in Cleveland, Ohio. The differences between each method’s initial and final lining, geology, and cycle sequence will be analyzed and compared.

Jun 13, 2023

By David Wilburn

Recycled materials are increasingly being used in road construction to supplement natural aggregate derived from crushed stone, sand, and gravel. An understanding of the amount of substitution that is taking place, its economics, and factors affecting the level of substitution is useful in estimating the potential for recycling and in assessing the total supply of aggregate. While U.S. consumption of recycled aggregates from crushed concrete is estimated to have increased 160 percent between 1994 and 1996; it comprised less than 5 percent of total aggregates consumed in 1995. Construction waste supply is regional, and is determined by infrastructure decay and replacement rates. Aggregate recycling rates are greater in urban areas where infrastructure is being replaced, natural aggregate resources are limited, disposal costs are high, or strict environmental regulations prevent disposal. Recycling is expected to increase as construction contractors attempt to save on transportation, disposal, and new material costs. Aggregate producers include recycled material as an option to consumers in order to prolong the life of their reserves and improve their range of products. Recycled aggregates can be a supplement for natural aggregates in selected applications, but their use should be evaluated locally based upon relative cost, quality, and market factors Because aggregate recycling is often affected by local and regional transportation systems, disposal and tipping fees, resource supply, the market for specific products, and municipal support, costs for three representative fixed site operations of different sizes were modeled. Under study conditions, all were found to be profitable, but highly dependent upon local tipping fees and market prices, which can differ significantly by location. Smaller operations were found to have different operational dynamics, often requiring creative marketing or incentives to maintain profitability.

Jan 1, 2001

By Stephen Krickovic

"Bleeding", as used in mine ventilation language, has a number of meanings among mining men and is regarded with different degrees of importance. This lack of uniformity stems from a number of specific situations. A method that is adequate in a mildly gaseous mine may fall short in a very gaseous mine. Projected bleeders could be dependable under a certain type of roof, and totally unsatisfactory under a different type. Similarly a plan of bleeders can be rendered useless due to undulations of seam and water in one mine and function well in another. Finally, what is effective in a mining system with partial recovery will not suffice with full recovery. You may wonder, then, if there is a common denominator for the essential function of "bleeding". In my opinion, there is, and it can be defined as controlled movement of air across an active pillar line toward the back and outby ends of the adjacent gob area into the headings provided for the purpose. The objective is to maintain as methane-free as practicable a belt adjacent to the working places, so that, if face ventilation is interrupted temporarily, the gas will not accumulate in dangerous volumes at the working faces before ventilation is restored. It's possible for these temporary interruptions to be unnoticed in time or at all. In such cases, ineffective bleeding could cause a disaster. This has happened. To control, there must be power. That is to say, there must be adequate air, pressure differential between the front and back ends of a pillar line to facilitate proper regulation for diverting of air to the various portions of the gob and as far away from the active section as is practicable. As an indication of the importance of pressure, it is noteworthy that one may provide and maintain in a reasonably open condition a heading or two for a bleeder system and fail to obtain effective bleeding .because air pressure differential is inadequate. On the other hand, you are all familiar with the fact that pillar lines in some seams can be ventilated adequately by air flow straight across the gob when the section is near a main return shaft and thus obtains a heavy pressure differential.

Jan 1, 1962

By J. A. Herbst, K. N. Han, P. B. Queneau, S. W. Asihene

As hydrometallurgy matures as a technology, more of its existing process knowledge will continue to be summarized in the form of detailed mathematical models. This development is happening at a time when major improvements in computer hardware have reduced the cost of computing. The opportunity then exists, through the solution of these process models, to design, control, and optimize hydrometallurgical plants on the basis of the physics and chemistry of its processes and less on empiricism. In this paper, a review of the current capabilities of sensors and phenomenological models for selected hydrometallurgical processes is presented. Future trends, in terms of the control and optimization of hydrometallurgical plants, are then explored. The possibility of simultaneously optimizing plant design and associated process control system performance is discussed.

Jan 1, 1993

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models have the potential to be used to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1993

By Surendra K. Mishra

The principles of dewatering fine coal has been examined in terms of solid- liquid separation. It is noted that the physical and physico-chemical properties of the particle-liquid system influence the rate and degree of moisture removal. Using postulated models the roles of polymers, surfactants and other physical means as dewatering aid are discussed.

Jan 1, 1988

By Craig Ammar

JAMIE DAVIS: Our next speaker is Craig Ammar. He's director of equipment management for Cyprus Climax Metals Company. He has, prior to this assignment, been responsible for maintenance at Bagdad Copper, Cyprus' Miami smelter, and Thompson Creek. Like Jerry, he's very shy and retiring, and doesn't have any strong opinions about maintenance. INTRODUCTION CRAIG AMMAR: The ultimate goal behind implementing a proactive equipment management process is to provide capacity assurance and ultimately increase an organization's ability to generate revenue while reducing operating costs. Targeting such lofty objectives has brought many an organization to its knees, utilizing new maintenance techniques, concepts, and technology aimed at making our lives better and more organized. The root cause of such frustration generally stems from a lack of understanding or support for the fundamentals of implementing a proactive equipment management process. There are just two types of maintenance programs, reactive and proactive. It's an established fact that you need a little of both to run an effective equipment management process, obviously more of one (proactive) than the other. Here are some telltale signs that your equipment management process is in trouble: -Maintenance is performed as a knee jerk reaction when equipment fails. -Repeated and frequent equipment failures occur, with no focus on eliminating the root cause. -Sketchy, inconsistent, unclear preventive maintenance is performed or there is no support for the preventive maintenance process. -No predictive maintenance technology process is in place, or little support for predictive maintenance exists. -Less than 50 percent of your work is generated by the maintenance group resulting from inspections.

Jan 1, 1998

By J. L. Chakravatti

INTRODUCTION Mining of uranium does not differ, in many respects, from the mining of other metals; the ore must be drilled, blasted and transported in an underground or surface mine. Underground mining proceeds by the continuous development and advancement of a network of passages and rooms or stopes from which ore is excavated. As in most mines, rock conditions and ore grades in uranium deposits vary from area to area and between different mines. For mineral benefications of this ore in the mills, use is made of various chemicals, often with toxic or hazardous properties.1 As well as the need to control the more conventional hazards associated with any mining and milling operation, special care needs to be exercised in the mining and milling of uranium because of the radioactive nature of the ore. This requires that we examine closely the radiation hazard areas encountered in the mining and milling of uranium, with the broad overview of some of the basic facts in the radiation hazard control programme. To place the hazard in its proper perspective, we require recognition, evaluation and control of those factors arising in and from the workplace which may cause sickness, impaired health and affect the well being among workers or citizens of the community. The radiation environment in uranium mine is complex and variable. Although uranium ore is only mildly radioactive, it naturally contains a complex mixture of radioactive isotopes. Workers are exposed to external gamma radiation, to some beta radiation and to airborne radon, radon daughters and ore dust. All of these types of exposures warrant considerations in formulating control procedures but, in general, radon daughters are known to present the dominant risk. The basis of dose limitation in radiological protection is risk limitation. Long-term epidemiologic studies of United States uranium miners and that of miners in Czechoslovakia indicate that the incidence of lung cancer can be accounted for by a linear relationship with exposure to radon decay products.2 On the basis of this proportional exposure-risk relationship, a risk coefficient for lung cancer in the range of 1-5.10-4 WLM-1 during the total lifetime, has been estimated by UNSCEAR3 and other researchers. It should be noted that this risk coefficient includes the excess lung cancer risk from external gamma radiation in mines and from other carcinogenic chemical effects, if any, to which the miners are normally exposed during their underground work. It also takes into regard the possible synergistic influences. This paper reviews the occurrence of radiation and its control factors and the development of engineering design features for the environmental control at Denison Mine. NATURAL URANIUM SERIES Uranium is the most common element in the Earth's crust. It is widely distributed in nature in all rocks and is readily measurable in the sea. Hence, radon gas is universally produced in every part of the globe. Mining is patently confined to ores containing more than half a kilogram, or so, per tonne of uranium unless it is combined with other marketable metals. Uranium-238 is the first element in the uranium series. In all, there are 13 radioactive decay products of 238U (Fig. 1), ending up as a stable isotope of Lead-206. The whole basis of the radiological hazards associated with the mining and milling of uranium is dependent on the behaviour of these isotopes during each phase of the process.

Jan 1, 1981

By Jon C. Yingling

Techniques for optimization of mineral processing flowsheets are reviewed. Though not yet widely used in the minerals industry, approaches for chemical process optimization based on successive quadratic programming (SQP) algorithms may be employed to determine optimum unit design and control settings for a mineral processing flowsheet. Moreover, in certain mineral processing flowsheet applications, specialized techniques can be applied because of the nature of the system relations. These techniques offer advanta es in efficiency. Moreover, their capability exceeds that o f the SQP approaches since simultaneous optimization of circuit configuration and unit controls can be addressed.

Jan 1, 1990

By H. Suharyono, R. Hogg

A laboratory investigation was performed on flocculation following the addition of polymer to slurries flowing through pipes and in-line (static) mixers. Results are presented showing the effects of flow velocity, pipe length, in-line mixer elements and the use of multiple addition points. Flocculation performance was measured by the settling rate and the supernatant turbidity. The effects of agitation and mixing time are shown to be generally consistent with the results of equivalent tests (both batch and continuous) conducted in stirred tanks.

Jan 1, 1997

By Donald Towse

The Permanente plant of Kaiser Cement & Gypsum Corporation is located at a unique thick deposit of Calera Limestone (Figure 1) on the southwest side of San Francisco Bay. Limestone is rare in the eugeosynclinal Franciscan assemblage, constituting less than 0.1 percent of the total volume. On the northwest part of the San Francisco peninsula Calera Limestone is present as isolated masses from the type sect ion near Rockaway Beach southeastward for ten miles, where the belt is truncated by the San Andreas fault. The large Permanente deposit is sixteen miles south of the truncated belt, on the northeast side of the San Andreas fault. Scattered small exposures are known for about twenty miles southeasterly from Permanente. (1,2) Most deposits of Calera are thin; the type section is about two hundred feet thick. At Permanente, however, the normal limestone section contains at least four hundred feet of limestone; and, due to folding and extensive faulting, the total vertical thickness of the limestone section is over 1400 feet. The unusual thickness of limestone is due to low angle thrust faulting. This fortuitous structure formed a deposit of limestone that supplies an 8,500,000 barrel cement plant in a major metropolitan market.

Jan 1, 1966

By S. Vijayan

Despite the limited demand for rare-earth elements, as well as yttrium and scandium, in conventional applications, the emergence of ne~ high-technology applications such as supermagnets, lasers and superconductors is expected to result in significant demand for some of these elements. This paper examines the anticipated applications and demands for rare-earth elements over the next decade and their implications on the utilization of available resources. Process methods for the recovery of rare-earth elements from conventional and unconventional resources are reviewed in the context of their growing demand. Challenges facing the industries in meeting this opportunity are also discussed.

Jan 1, 1988

By H. Mischo, F. Daniela, L. Schaarschmidt, I. Paschke

In order to safely store radioactive waste long-term, HAW repositories in saliferous formations have to be backfilled. The main purpose of those backfill operations is the restoration of the geological barrier function of the containment area. For best possible results the used material should be of a comparable composition or characteristic for the host rock formation. Additionally, the material should show a high density after completion of the backfilling process as well as a low permeability. A major aspect to consider in these processes is the minimization of the gap of the backfill body to the roof of the drift. To fulfil those requirements, a micro-structure stabilized crushed salt backfill material has been developed as part of the GESAV-I-project. Due to the material composition of this so-called GESAV-material, salt mineralcrystallization processes start after emplacing it, a process that leads to the polyhalite formation. With the crystallization of polyhalit, the halite grains are bridged, which in return stabilizes the matrix of the backfill. The GESAV-II-project continued successfully what GESAV-I started and determined an ideal backfill method in order to build the backfill bodies composed of GESAV-material. Due to the compaction of the material during emplacement by vibration, high in-situ densities, low permeabilities and a backfill factor close to 1 was able to be reached. In the following SAVER project this journey of practical test underground will be continued.

Mar 2, 2022

By Keith G. Wallace, Robert Wise, Ian J. Duckworth

This paper describes a case study for the ventilation planning at Utah Fuel Company's Skyline Mines which are located outside Price. Utah. The Skyline Mines are currently comprised of two longwall coal mining blocks located in two different mines. A third replacement longwall block is currently being developed. Future ventilation systems for the mines were determined by establishing ventilation models developed from data collected during a detailed ventilation survey. The paper discusses the challenge to coordinate immediate ventilation requirements with long-term demands. The continuous movement of the longwall, which frequently represented the only open split in the ventilation network, resulted in cyclic ventilation demands dependent upon the length of the tailgate. A series of system configuration changes were recommended based on the results of the network modeling exercise and an economic evaluation of the various options. The scope and cost of the configuration changes, and the mead improvement resulting from these changes is discussed.

Jan 1, 1995