Search Documents

By Lyall Workman

New mines are frequently located at altitudes above 3,000 meters (10,000 ft.). Drill selection must take the altitude effects into account, to insure high productivity and good bit life. In particular, compressors must be sized differently than for low altitude operation. A larger compressor is required to deliver adequate air to the bottom of the blasthole. Many drills in remote locations use diesel engines as the prime mover. Altitude effects on engine performance should also be considered.

Jan 1, 2007

By C. Partouche, T. Bernard

Blasting engineers are mainly concerned about fragmentation issues. Even further, this is the final goal of using explosives. A lot of models have been developed for controlling fragmentation distribution, but most of the time, they are based on physical phenomena using field data as input for rock characteristics. Fragmentation is a result of two phenomena: waves from the borehole, damaging and cracking the rock, and gas pressure, widening those cracks and spreading out rock fragments. This model simulates the P wave escaping from boreholes and the cracks created by these P waves. It takes into account rock characteristics, provided by digital imaging, and explosive characteristics coming from VOD measurements. What we need to focus on, is the interaction of P waves coming from each borehole related to different timing sequences. This paper presents several simulations that show the influence of the timing and the sequence accuracy on the fragmentation distribution.

Jan 1, 2002

By Miles Huntly

This paper will discuss the ideas and actions that led to the development of a Drill Improvement Team at an open cut coal mine in Australia. It will show significant cost savings can be attained by forming a focused Team derived from all the participants that go into drilling a blast hole

Jan 1, 1999

By Richard N. Snyder

In this system for connecting blasting caps to the initiation source, the need for a redundant design structure provides more reliable method of explosive initiation. This is accomplished by using a complete system starting at the blasting control, through the initiation line structure through the initiation line and connecting blocks to the blasting cap. The connecting structure between the initiation device and the blasting caps may be connecting blocks or other means.

Jan 1, 1995

By R D. Skaggs

A good blast is dependent on a well engineered design. However, a good design's performance depends on the control of the drilling and loading of the blast holes. The key stone to good blasting is the drilling of straight holes of the correct orientation in the required positions.

Jan 1, 1991

By Jaak J. K Daemen, Carol Geertson

A portion of a tailings impoundment may need to be removed with the expansion of an open-pit mine in northeastern Nevada. The tailings are saturated and consist of fine silty soil. During the removal of the tailings, they would have no support structure and vibrations induced by blasting in the pit could lead to slope failures.

Jan 1, 1998

By Syed M. Tariq, John W. Wilson, Paul N. Worsey

The position of a major joint in relation to a blasthole has a significant effect in presplitting. Broad research into the combined effects of firing two decoupled blastholes has been performed in the past. The effects of joints simulated between two blastholes has also been evaluated. However, no attempt has been made to investigate the splitting effects produced by firing a single decoupled blasthole. This paper presents the results of such an investigation.

Jan 1, 1996

By John T. Day, Lex L. Udy, Mark L. Thomas

When we consider that the purpose of blasting is to fragment rock or ore so it can be subsequently handled and processed, we can see that the cost of blasting, in reality, affects all downstream steps of the mining (and in some cases) production processes. The productivity of all subsequent operations is influenced by the degree of fragmentation of the primary blast.

Jan 1, 1987

By Chang-Ha Ryu, Hyung Yang, Hyung-Sik Yang

Ground vibration by rock blasting causes many environmental problems to adjacent structures and human bodies. Growing concerns have been given to the effects of dynamic loading induced by blasting works near safety-related structure like nuclear power plant, hospital, broadcasting station, research institute and tish farm, etc. In order to ensure the safety, rational safe criterion should be established. It requires development of a model to predict the design parameters through more systematic measurement and analysis. Primary estimation by adequate model with general parameters will be very useful for safe design and understanding the possible hazards in advance.

Jan 1, 2001

By T N. Hagan

Where explosion energy moves rock from the in-situ to its desired location without considerable assistance from digging and/or hauling equipment, good fragmentation is of minor importance. Maximum displacement must remain uppermost in the mind of the blast design engineer.

Jan 1, 1979

By Richard Scales, Giles Hellyer, Ian Travers, Dean French, Peter Bellairs

"The Mt Whaleback iron ore mine is located in the Hamersley Province situated about 1OOOkm to thenorth of Perth, the capital city of Western Australia. A small but significant portion of the waste in Mt Whaleback presents problems due to its ability to react with normal commercial bulk explosives resulting in premature detonations, two of which occurred at the mine in 1983 causing great consternation as well as disruption to the mining operation. The techniques and procedures developed to overcome this problem were based on the use of tough durable, acid and heat resistant liners to provide a physical barrier separating the explosive from the rock togetherwith the development of an accurate down the hole remote temperature logging technology. The liner technology was developed due to the inability to produce a reliable inhibited ANFO despite exhaustive mine based testwork."

Jan 1, 1999

By Syed M. Tariq, Paul N. Worsey

Pre-splitting is now widely used to minimize overbreak and to protect final surface rock excavation profiles in large scale civil construction projects, open pit mining and quarrying. Jointing has been shown to affect the success of pre-splitting and the smoothness and integrity of the resulting rock face. Many facets of jointing have been investigated in detail, including the inclination of joints with respect to the desired pre-split plane, the effects of various filling materials, etc. However, the effects of joint frequency and spatial positioning has been paid little attention. The paper addresses this issue.

Jan 1, 1995

By Edward Fitch

The DOE is evaluating Yucca Mountain, Nevada as a potential site for disposal of high level nuclear waste. Yucca Mountain is located approximately 160 km northwest of Las Vegas on the western edge of the Nevada Test Site and the Nellis Air Force Range. An exploratory tunnel has been constructed through Yucca Mountain for site characterization. A controlled drilling and blasting technique, smooth wall blasting, was used to excavate the TBM starter tunnel and alcoves off the main tunnel to provide areas for scientific investigation. Fundamental to the blasting program has been the use of two blast design equations used in concert to minimize blast damage to the surrounding rock mass. The first of these equations was developed by Roger Holmberg and estimates near-field peak particle velocity that is the basis for minimizing blast damage to the host rock. The second of these equations was developed by B. H. Sanden and provides bore hole pressure estimation which allows controls to minimize crushing of the rock mass along the perimeter yet allowing enough force to create tensile failure between perimeter bore holes. This is key to the smooth wall blasting technique. To date, essentially the same controlled drilling and blasting program has been in place for all excavation requiring controlled drilling and blasting at the ESF. The controlled drilling and blasting program uses an iterative process to achieve continuous improvement in the blast rounds. This involves interaction between Architect and Engineer (A/E), Constructor, and Testing Coordination O&e (TCO) to ensure each blast round successfully meets the expectations of affected participants. The A/E requested that the TCO provide validation of the near-field peak particle velocity estimation under the Construction Monitoring Program. Data gathered under this program were reduced by statistical analysis and used to verify blast design parameters and provide a site specific blast damage relationship.

Jan 1, 2000

By E E. Cloete, R I. McCrindle

Permitted explosives were previously nitroglycerine based and cap sensitive. Due to safety, health and environmental requirements, water-containing explosives, such as watergels and emulsions, were used instead. However, in order for these explosives to perform at their designed level during blasting, a more powerful stimulus than is delivered by detonators on their own is required.

Jan 1, 1999

By Kenneth Eltschlager

Post-blast assessment techniques using off-site data which includes location, seismograph and photographic data were discussed during the Blaster’s Weekend at this year’s ISEE Conference. Blast and property locations with commonly available GPS units allow for the spatial relationships surrounding the blasting to be documented. When distances are coupled with the charge weight per delay, the scaled distance can be calculated to any structure for either compliance with the rules, or to project limitations. When blasting seismograph data is obtained, the scaled distances are then able to be plotted against ground and air vibration levels for post-blast assessment purposes.

Jan 1, 2007

By Robert L. Brooks

Blasting liability problems are frequently compounded by a company's inability to effectively communicate with concerned property owners and the lack of adequate complaint documentation. Often, by the time the insurance carrier becomes involved in a blasting claim, the situation has deteriorated to the point that a solution agreeable to both parties is virtually impossible to reach. The insurance carrier, wishing to minimize their lose potential may decide to pay on a somewhat questionable blasting claim rather than be drawn into lengthy civil proceedings that would ultimately end up in front of a jury with little chance for a successful outcome.

Jan 1, 1992

By Hans Florin

This paper describes the modification of a nonelectric detonator which is ignited by a signal tubing. The heart of the new detonator lies in a so-called ignition transmitting element. The construction of the transmitting element is such that the detonator remains closed even after the signal tube has functioned. Due to the sealing of the delay element, this nonelectric detonator achieves the same accurate delay timing as high tech delay electric detonators and will not fail due to a sudden pressure loss.

Jan 1, 1988

By Calvin L. Cumerlato, David E. Siskind

The Bureau of Mines has monitored structural responses to airblast overpressure produced by munitions disposal at the McAlester Army Ammunition Plant. The Purpose of this study was to determine if the blasting caused vibrations, airblasts or structural responses that could possibly be responsible for cracking or other damage observed in nearby residences. Monitoring took place during a 3-month period at 10 selected residences surrounding the plant. By the end of the monitoring period, nearly 2300 blast-related events had been recorded.

Jan 1, 1994

By L D. Lawrence, R S. Day, Gordon Coleman

Commercial emulsion explosives are typically characterized by their relatively high detonation velocities due to the intimacy of oxidizer and fuel and to their sensitization with glass microballoons. However, numerous blasting operations in softer, more porous rock formations are better fragmented with slower shooting explosives. Although mixtures of emulsions with large amounts of ANFO (60-80%) can considerably reduce the high velocities, little water resistance is achieved with low levels of emulsion blended with ANFO. "Water proof" blends containing typically 50 percent of emulsion become quite costly due to escalating powder factors in ANFO patterns. Blends of sensitized emulsions with 20-30 percent ANFO retain the high velocity characteristics of the emulsions as well as increased densities which can also adversely affect blasting results in softer rock formations. The introduction of a reliable and predictable on-site gassing process for sensitization and density control of repumpable emulsions, with or without added ANFO, offers the end user the option of supplying a final product more suited to his blasting needs. The capability to widely vary final product loading densities and consequently product detonation rates better tailors the final explosive to different rock characteristics. The beneficial advantages of this system in softer rock formations have been well documented. Overall comparison between these variable density products with typical repump emulsions containing solid density control will be reviewed. Besides the obvious cost advantages and safety advantages of these systems the end user is provided more definitive control of his blasting operation.

Jan 1, 1990

By John Cowin, Dan McCutchen

Cowin & Company has specialized in underground construction since 1924. This paper reviews the sinking of two shafts in the Alabama coal fields using bulk-loaded explosives. Each shaft is eighteen hundred feet deep, and their diameters were twenty feet and twenty-three feet. The first consideration in changing to a new explosives system was safety. Safety began with the explosive supplier training the miners in the use of the new system, from explanation of the pumping unit on the surface to hands-on training in the shaft. The considerations covered include establishing a thunderstorm exit plan, and reducing exposure time of the crew to explosives while loading. The system consisted of a specialized pumping unit and an advance emulsion product. Eliminating the need for nitroglycerin based explosives, and reducing sensitivity to mechanical shock were goals that were met. Performance in the shaft and ease of use meant morale of the miners using the system remained high and positive. Performance benefits discussed include reducing the number of holes in the round, and cutting explosives loading time in half. Damage to the ribs of the shaft was greatly reduced, making it safer to work near the ribs on succeeding rounds. Cleaning the bottom before drilling the next round also showed marked improvement. The economics of the system became very apparent when cycle time saved was allocated against fixed cost of sinking these shafts.

Jan 1, 2000