Search Documents

By Donald J. Westmaas, Fred C. Drury

The factors affecting the selection and use of exploisves have changed radically in the past three decades. The objective of this paper is to point out considerations which should now be employed by the Explosives Engineer in his selection and use of modern chemical explosives.

Jan 1, 1978

By Kenneth Eltschlager, Steven V. Crum, David E. Siskind

The Bureau of Mines was funded by the Office of Surface Mining (OSM) to determine how blast vibrations from a local surface coal mine were affecting homes in the towns of Daylight and McCutchanville, located in southwestern Indiana near Evansville. Although Daylight was about two miles from the blasting and McCutchanville four to five miles away, many residents claimed that blast vibrations were damaging their homes. At least one citizen felt that the vibrations worsened at the time the mine began cast blasting.

Jan 1, 1992

Prepare ATF Report of Theft or Loss (ATF Form 5400.5). A Report of Theft or Loss - Explosives Materials must be prepared when it is discovered that explosive materials are missing from inventory. Submit the original to the U.S. Bomb Data Center and keep a copy for your records. The form can be obtained from the ATF Distribution Center or from www.atf.gov. Although the U.S. Bomb Data Center should be notified as soon as possible, Federal law requires notification within 24 hours of the discovery. A full inventory check is also highly recommended (but not required) to locate missing explosives and to prevent future losses.

Jan 1, 2008

By U Nyberg

Peak particle velocity (PPV) and distance measurements from a single-charge blast test conducted by Swedish researchers in iron ore at the Kiruna Mine in northern Sweden are presented. They are used along with theoretical PPVs calculated using an equation based on hydrodynamics to determine a damage distance range caused by a single charge. This equation, which relates PPV to explosive properties, charge geometry, and distance from a charge, was then applied to a charge of different geometry that was used in drift rounds. A comparison between calculated and measured PPVs suggests that the stoping holes likely damage the easer hole locations, and the easer holes produce damage to the perimeter hole locations. The practical effect is that typical damage limit predictions based on measurements conducted in fresh or undamaged rock are conservative. This suggests that even when perimeter control is not exercised in drifting (i.e., the perimeter holes are fully loaded), the resulting damage may be less than normally expected due to the wave damping effect of the pre-damaged rock. Due to the damping effect, poor perimeter blasting practices are somewhat self correcting. However, it must be strongly emphasized that well-engineered blast designs with perimeter control are highly beneficial in relation to both economic and safety aspects.

Jan 1, 2011

By Raymond Hofstetter, Paul Worsey

The purpose of this paper is to investigate commonly used methods for mitigating the effects of shrapnel from linear shape charges (LSC) used in the demolition industry. Primarily the problem is not that shrapnel poses a threat to human bystanders, but rather it can affect the other charges in the demolition or damage to structures in close proximity to the charges. This research aims to determine what methods have success at stopping shrapnel, what methods do not, and to promote an awareness of the dangers of using the LSC without any protection. The project was carried out at the Experimental Mine site at the Missouri University of Science and Technology. This research is an undergraduate research project to fulfill the requirements for the Explosives Engineering minor program at MST.

Jan 1, 2008

By S Burchell

During the past few years, high-speed cameras, laser surveying equipment and photogrammetry have become standard tools for recording blast geometry and results. While laser profiling yields accurate 3-D measurements, most cameras capture only two-dimensional images. Attempts to extract 3-D information from photographs have been unsatisfactory. Recent advances in electronic imaging and computer programming have made it possible to develop a 3-D computer based analysis system which can capture and measure 3-D images quickly and accurately. This paper describes the technology to create 3-D images and to analyze blast geometry before, during and after the blast.

Jan 1, 1992

By Hairong Zeng, Shahram Tafazoli, Edmond Chow

Blast fragmentation is one of the main parameters for optimizing mineral processing, but reliable data is difficult to acquire, resulting in unpredictable performance and efficiency. Crusher and grinder circuits are designed to process specific rock size ranges. Oversized rocks require extra energy to reduce before feeding into the process, and undersized rocks indicate that the process is not used to its full extent. Blast design is the key to controlling the blast fragmentation, so the ability to accurately monitor the particle sizes is imperative.

Jan 1, 2011

By Bengt Ljung

Manual charging of long upward drilled holes in mines is a heavy and risky job today. Mechanization of this work has been requested for some time by miners, their supervisors, industrial safety organizations and the trade unions, all of whom are interested in improving the working environment. This paper presents newly-developed charging systems intended primarily for charging in connection with sublevel caving and sloping. These systems have been field-tested during 1977 in the LKAB mines in northern Sweden. The results of these field tests and the results of laboratory work conducted to help eliminate the risks involved in charging explosives are also discussed. The equipment being tested (see fig. 1 and 2) consists of a charging vehicle with articulated steering, the PT-60, which has been equipped with a hose feed system mounted on the hydraulic extension boom. From a sheltered position, the operator brings the detonator and primer to the hole opening, after which the hose is pushed in mechanically to the end of the hole. Measuring equipment indicates when and if the end of the blasthole is reached. The operator then withdraws the hose mechanically as charging takes place.

Jan 1, 1978

By John Petty, John Loviza

Single sentence describing content-- "The best ally an Explosives Engineer can have in a court of law is a regulations enforcer stating all codes and standards were met on a jobsite".

Jan 1, 1996

By Raymond V. Adolphson

The introduction of a new explosive component in 1955-56, called ANFO, featured much safer, effective blasting characteristics when compared to dynamite, accompanied by a notable reduction in cost. These savings mounted as borehole diameter or depth was increased with ANFO volume subsequently enlarged.

Jan 1, 1983

By Kfw Eick

The paper describes the use of the Nonel millisecond delay blasting system in narrow, deep, tabular ore bodies and briefly describes the standard stoping method as used on Harmony Gold Mine and compares this with the new Nonel short panel system.

Jan 1, 1990

By Jung-Hoon Ryu, Chang-Ha Ryu, Byung Hee Choi, Yang-Kyun Kim

Control of overbreak in tunnel blasting is one of the key factors affecting the construction expenses as well as safety. Overbreak causes an increase in the cost of construction by requiring an additional amount of shotcrete. In addition, blast damage to the final rock face may cause instability and rock fall hazards. For these reasons, controlled blasting is an indispensable routine in tunnel excavation in order to get a smooth face and to reduce damage to the final wall. We have experienced a very poor quality of excavation depending on the tunneling sites although a similar design of controlled blasting technique was applied. Field experiments over 40 rounds were carried out to investigate the cause of the poor results in tunnel blasting. In this paper, discussed are the parameters affecting the overbreak and some findings from the field experiments. Overbreak could be controlled considerably by adjusting some parameters before the efforts of developing a new blasting method.

Jan 1, 2004

By Larry R. Fletcher, Virgil J. Stachural, Matthew N. Plis

The Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of a series of tests to improve presplitting at a western surface coal mine. Reductions in overbreak were achieved by decoupling and/or repositioning the main explosive charge in the 10-5/8 inch presplit blastholes that formed the highwall. Blast designs are presented by the authors for 1) repositioning the explosive charge from a weak rock layer to a stronger rock layer, 2) decoupling with cardboard tubes in the toe region, and 3) suspending bagged powder at intervals along the length of the blasthole. About the same total quantity of explosives was used in all three test designs. It was readily apparent from periodic visual examination and photographic surveys of the highwalls that the amount of rockfall was reduced, and with a longer delay before rockfalls began, in all test areas.

Jan 1, 1991

By Ivan Kovac, Pero Marjanovic, Branko Bozic

"The paper deals with results of geophysical survey of the rock masses, and the blasting parameterswhich have effect on the fragmentation in quarries . A relationship between the burden, which is the distance between the charged borehole and the free rock surface, and the velocity of longitudinal waves in the rock mass is established based on measured values for different quarries. It is shown that the drilling geometry can also be detemrined from this relationship."

Jan 1, 1999

By F O. Otuonye

Full-face blasts were fired in a 12 x 8 ft drift of an underground hardrock mine in a basalt formation with porphyry copper to study the effects of drill pattern and explosive type on the size distribution of the resulting muckpile. Each muckpile produced by five full-face blasts was sampled four times with a scooptram equipped with a 5-cu yd bucket and the size distribution of the broken rock in each bucket was determined by screen analysis. Results show a strong dependence of the fragment size distribution of muckpile on the blast pattern and explosive type for a given rock type. The mean fragment size of the broken rock was compared with the predictive equations of other investigators. Random sampling of the muckpile from full-scale blasts and screen analyses of the samples are recommended in assessing the size distribution of the broken rock because of scaling errors that are inherent in full-scale blasts when designed from results of small-scale tests.

Jan 1, 1985

By Neal Lee

Reduced relief horizontally means an increase in energy expended vertically into the rock surrounding the stemming column, and potentially through the stemming column. The vast majority of holes in any surface blasting operation are afforded two horizontal relief faces at the moment of firing, whether by existing relief faces in front of and to one side, or previously blasted hole(s) in front of and to one side of the holes in question. When the energy expended in any hole on the blast pattern has less than two Horizontal Relief Planes or faces (referred to moving forward here as “HRPs”) available to it at the moment of firing, a higher percentage of the available energy is directed vertically. In the analysis of recorded videos by the author, one will note the fact that stemming ejection/flyrock is observed to a much greater degree from the center of almost all patterns when they are timed to “pull out of the middle” (“box cut" timed patterns). This is because the first hole to fire in each row has only one Horizontal Relief Plane, which significantly decreases horizontal avenue for energy release for these holes. This of course results in an increase in the amount of energy expended vertically. This paper proposes a novel methodology to modify the stemming to better use the explosives energy of each hole, while controlling side effects such as flyrock and airblast.

Feb 6, 2023

By David E. Siskind

In the early 1980's, the Bureau of Mines published four reports of structural response and damage from surface mine blasting, vibration monitoring, and analysis methods. These findings replaced simpler and less restrictive Bureau criteria dating back to 1962 for ground vibration and 1943 for airblast.

Jan 1, 1991

By Mark S. Stagg, Stephen A. Rholl

The firing times of millisecond-delayed initiators are random variables that exhibit varying degrees of scatter. This scatter can cause crowding and overlap of adjacent delay periods, which results in adverse effects on safety, fragmentation, and blasting vibrations.

Jan 1, 1988

By Mark S. Stagg, Steven V. Crum, Stephen A. Rholl

As part of its ongoing research concerning rock fragmentation by blasting, the Bureau of Mines has undertaken a series of test blasts where six cylinder-shaped pieces of granite rock were fragmented using high explosives. The tests were intended to: 1) Establish a dataset that could be used in the development and verification of theoretical models that simulate rock blasting and 2) To add to the fragmentation data currently being collected by Bureau researchers. The cylindrical geometry was chosen so that the fragmentation could be directly compared to two-dimensional computer simulations that assume an axisymmetric configuration as well as more sophisticated three-dimensional models. The granite cylinders, Carnelian granite and Charcoal granite, ranged in size from about 0.46 meters (18 inches) to 0.58 meters (23 inches) in diameter by 0.91 meters (36 inches) to 1.52 meters (60 inches) in length. Physical rock properties tests performed on the Charcoal granite cylinders indicated that the rocks did in fact have similar physical characteristics. PETN-based detonating cord and dynamite were used as the explosive charges and estimates of the values of some important physical properties are given. For the first five tests, the blasted rock was contained by a heavy rope mat suspended inside the Twin Cities Research Center's blasting shelter. The fragments from each of these shots were sorted and weighed to determine the corresponding fragment-size distributions. Even though different types of granite and cylinder sizes were used, similar fragment distributions were produced from shots that used a similar explosive, in this case the PETN-based detonating cord, and comparable burden-to-charge diameter ratios. Significantly coarser fragmentation was produced from a blast that used dynamite as the explosive charge. Fragment velocities were calculated using photographic data from the sixth test which was shot unrestrained in a quarry and filmed with high-speed cameras.

Jan 1, 1990

By Yoshiharu Tanaka, Keita Morooka, Masaaki Yamamoto, Katsuhiko Kaneko

Smooth blasting is the standard method for underground rock excavation, to reduce over break and remaining rock damage. We already utilized the high accuracy of the electronic delay detonator to investigate its effect on over break remaining rock damage, and surface smoothness. And we presented at 11th annual symposium on Explosives and blasting Research.

Jan 1, 1998